Database Develop

What's Wrong With My Computer!?!?!

I have two PC's, one is a XP Media Center Edition. It had a virus on it and kept getting a corrupt file, so my techyish relative came and wiped the hard drive from scratch ( or so he says but it was a partial wipe) and reloaded the OS onto it. It worked fine, but then kept getting the corrupt file again. I then decided to order the recovery disks from HP, which is the computer manufactuer. They arrived and I put them in, followed the steps, and all wen well until I came to the recovery partition. It was backing everything up ( one time process only) into the recovery partition all fine and dandy until it came to a file that had to do with Microsoft Office. It stayed their for about 45 minutes backing up this file where the longest had been 10 minutes max for all the others. I looked the file up and it said it was a small 10 mb file, so I turned the computer off and went to normal without the recovery partition. Worked fine until one day something happened and I guess I needed to do the recovery again (it's been a few months since this has happened) and did all the steps, but it wouldn't take. It gets to about 4% and then dies with a BSOD and this message:
A problem has been detected and Windows has been shut down to prevent damage to your computer.
DATA_KERNAL_INPAGE_ERROR
If this is the first time you’ve seen this stop error screen, restart your computer. If this screen appears again, follow these steps:
Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any Windows updates you might need.
If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use Safe Mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode.
Technical information:
*** STOP: 0x0000007A (0xE121F318, 0xC0000185, 0xBF8B6147, 0x1C610860)
*** win32k.sys – Address BF8B6147 base at BF800000, Datestamp 3b7de698
Copied it down word for word, space for space. Can anyone help me get this thing up and running again? It's now getting important.

Forgot to mention that I get the same problem each time I put the recovery disk in.

I'd recommend using a NON-Recovery Disk, but rather a Clean, Non-OEM, Windows Disk. If the issue pertains to the Kernal, it's usually unfixable without a Hard Boot of the Drive. You should do more than Re-Format.. you should delete all the partitions off of your Hard Drive with a Windows Disk, then pop in the Recovery Disks and do the OEM install.

So I need to wipe the hard drive clean again and put in another non OEM OS?

Not quite. Wipe the HDD clean with the NON-OEM Windows Disk, as most Recovery Disks do not allow you to alter the Partitions [Everything is done for you], then pop in your Recovery Disk and let it install the new Primary, and possibly the Recovery, Drives.

I see what your saying now, so what exactly happened to it?

Get Windows 7

I have windows 7, that's my other computer.

The guy at the un paso store got you too!!

At the step store? Lol.

PurpleLlamaLover said:
I see what your saying now, so what exactly happened to it?
Click to expand...
Click to collapse
When your supposed "Tech Savvy" friend attempted to fix your computer.. he, I'm assuming, did a simple "Repair" of the partition with an XP Disc. That is LITERALLY the most unwanted version of a fix ever... All it does is replace the system files, but keeps all of the other software that may have been conflicting with the system itself, BUT usually, all of the software is inaccessible. It's still on your computer, f*cking it up, but you can't see it.
Thus I always say, "If you get a bluescreen... more than once, and don't know what the code means... don't repair your computer.. re-format that b*tch after recreating the partitions."
But, if your XP compy has the specs to support Windows 7, your best bet, all in all, would be to install Windows 7. Doing so will save you the hassle of having to manually download all of the drivers for it... unlike installing a non OEM Windows XP [have to download & install the drivers manually].

PurpleLlamaLover
it sounds like the HP recovery disk could well be corrupt,
So you now have 3 options:
1. Try Linux Ubunut 10.4 LTS (Free Distro)
2. Buy a ligit copy of Windows 7
3. Download Windows Vista / 7 / XP from a torrent
and try untill you find a OS you lyk

Agent Zach said:
When your supposed "Tech Savvy" friend attempted to fix your computer.. he, I'm assuming, did a simple "Repair" of the partition with an XP Disc. That is LITERALLY the most unwanted version of a fix ever... All it does is replace the system files, but keeps all of the other software that may have been conflicting with the system itself, BUT usually, all of the software is inaccessible. It's still on your computer, f*cking it up, but you can't see it.
Thus I always say, "If you get a bluescreen... more than once, and don't know what the code means... don't repair your computer.. re-format that b*tch after recreating the partitions."
But, if your XP compy has the specs to support Windows 7, your best bet, all in all, would be to install Windows 7. Doing so will save you the hassle of having to manually download all of the drivers for it... unlike installing a non OEM Windows XP [have to download & install the drivers manually].
Click to expand...
Click to collapse
I'll try and get 7 for it. It was the last of the XP models, just before vista so i'd think it should be able to run 7. Think I need a new hard drive?

Bro that Simon_WM guys a genius. Listen to him.

Yea. This is my computer here, http://h10025.www1.hp.com/ewfrf/wc/...en&dlc=en&cc=us&product=3257746&lang=en#N1030
Think it'll run it?

PurpleLlamaLover said:
Yea. This is my computer here, http://h10025.www1.hp.com/ewfrf/wc/...en&dlc=en&cc=us&product=3257746&lang=en#N1030
Think it'll run it?
Click to expand...
Click to collapse
it may run with a lag

I just want it back up and running, I don't want vista though. On the little windows sticker is says "Vista Capable" but i've heard bad things about it, especially rom updating.

PurpleLlamaLover said:
I just want it back up and running, I don't want vista though. On the little windows sticker is says "Vista Capable" but i've heard bad things about it, especially rom updating.
Click to expand...
Click to collapse
ummm i use vista and have updated all my win mo phones on it...never had a problem

Really? Well, i'll keep in mind if I can't get XP back on it. I'd rather just have 7 and XP. I don't care what it runs as long as it runs again.

the best suggestion in this thread was install linux , however i take it that isn't a possibility. so here's what you need to do, you will require the following:
1) a fresh mind
2) a freshly burned copy of XPwhateverflavoryouwant
3) you do not care about anything on that drive.
put in freshly burned xp into computer, boot to cd drive, follow onscreen instructions, delete all partitions, create new NTFS partition, install to new partition.
if error comes back, it is not a software issue. fixing a xp bsod really is simple if it isnt hardware related.

Windows XP Install via Flashboot

but i'm using flashboot to put XP back on my lapttop, and i think it will only boot from the usb drive, is there a way to install to my hdd? and i have no optical drive in it -,-;

Erm, good luck
XP does not support install from USB.
Best you can do, is install via network, or invest in an optical device as they surely must cost about ten cents from one of your WHARLMARTS

using wintoflash, hopefully it works....

acolwill said:
Erm, good luck
XP does not support install from USB.
Best you can do, is install via network, or invest in an optical device as they surely must cost about ten cents from one of your WHARLMARTS
Click to expand...
Click to collapse
yes it does. get the hp format tool to install a boot sector on your flashdriv e then dump the xp cd to your flash drive boot from the flash drive and run. the xp setup inside of the i386 folder.

Like I said previously. Windows XP doesn't support that.
Considering I looked into this probably about 5 years ago, I still stand by my first comment.
If you still want to attempt to install a 9 year old operating system, then you may want to read these:
http://www.pctipsbox.com/installing-windows-xp-using-a-usb-flash-drive/
http://en.kioskea.net/faq/3065-installing-windows-xp-from-a-usb-key

got an external usb and got xp for better drivier usuilities.

alcolwill is prolly drunk , dont worry about him , heres wat ya redneck is lookin for
1, get ur hands on a win7/xp image
2, burn it to your favorite min. 4gb/(1gb for xp) usb drive with your favorite disk burning program that supports writing to usb (ultra iso for one < top menu , burn boot image , its vital that u dont just pull the files cuz u wanna create a booting sector)
3, set >boot from external< on and >boot priorities< for usb drive to correct value in bios (some bioses also have Esc for boot menu option)
4, ????? (restart comp)
5, PROFIT
if doesnt work , ask family for other pendrive/c-reader , not all can boot

went ahead and picked uo an external optical, so its all good! =]

WinXP from USB
it is possbile because i've done it. all it is a bootable drive

[Q] Can not ADB my device?!

I have a Verizon Galaxy Tab 7 (SCH-I800) and I can not link up to it in ADB.
I have installed the Android Development Kit, Samsung drivers, and downloaded CM10.1.
I was able to contact the tablet in command prompt through heimdall and push clockworkmod recovery.
I'm following this guide:
http://rootzwiki.com/topic/33743-ext...rd-only-guide/
I've removed the internal memory card.
I've modified the update.sh file and rezipped everything.
I just need to know WHY adb cannot find my device. When I type "adb devices" in the command line NOTHING shows up. I've tried reinstalling the samsung driver, reinstalling the driver that came with heimdall, and updating the samsung driver via windows update.
By the way, this device would bootloop at the verizon loading screen, could not be updated, and could not load its original android OS, therefore I cannot turn on debugging or anything like that. Alls I can do is access the "PC connection" yellow screen and the CWM bootloader I pushed with Heimdall.

By "Internal" Memory ya meant "External" Memory right? as the Internal Memory is the 16GB Flash ROM.
In any case all pedantry aside. Did you remember to check the USB Debug Setting?
I think you can find this under the Wi-Fi Settings (On the Samsung Stock ROMs), IIRC it should be near the "Samsung Kies / Media Player / USB Storage" Settings. On CM10 Builds you'll find it in the "Developer Settings" near the bottom of the List.
Pretty sure you have to check this "Flag" before you can use ADB on your Device...
In that case consider yourself bricked!
In this case I'd recommend you find the Overcome Recovery Package: HERE
Install such Driver that you may need, then fire up Odin3 v1.7
Then set your Device into Download Mode (e.g. Hold Volume Rocker down + Power till you enter the Download Mode Screen)
Pit -> gt-p1000_mr.pit
PDA -> GB_Stock_Safe_v5.tar
Phone -> modem.bin**
Most People would just use the XXJPZ (GSM modem.bin), here but, since you have a CDMA Phablet, you'll have to find and pick the correct modem.bin File that is the best match for your CDMA Device. This is also likely why your now soft-bricked.
Hopefully after all this rigamarole you'll land up on a Stock, non-branded Samsung Gingerbread 2.3.3 ROM.
To which I would just download This, and that should give you Root.
Without all that tedious mucking about with ADB.

The internal chip has failed. I cannot boot the device whatsoever. I removed it as the link states. Therefore i cannot check off debug mode on the tablet. I will try your suggested method and report back

Don't look at Overcome method if you have a CDMA tab.
It will only brick your tab if it ever worked at all.
Regarding bad internal memory, there are two chips. The OneNand 512MB and the MoviNAND 16GB.
If your OneNAND is the one broken, removing the MoviNAND achieved nothing.
The bootloader, modem, (and is it /system too of stock rom?) sits on OneNAND.

If you look at the link I posted, my tablet was doing the same exact thing as pictured in the link. Saying it could not mount any files or anything. No matter what I did, it would just get to the verizon loading screen and keep flashing "verizon".
I haven't tried the "overcome" method as it didn't really seem like it'd work.
I want to ADB my device to push the new ROM to it. I've already formatted the SDcard as suggested in the guide. Since clearly no one is clicking the link and reading the guide, I'll post it:
Summary:
- Open up the device and take internal SD Card out.
- Re-assemble the device.
- Partition the external SD Card (3 partitions, two small ext4 and one big FAT32)
- Modify ICS or later ROM's update.sh to use partition 3 as external SD Card.
- Flash modded ROM via CWM (and Google Apps optional).
- Enjoy
Taking it appart:
Don't panic!, if you can use a screwdriver and build with Legos you are qualified to do this!
iFixit does a wonderful job of showcasing how to open the device up that I rather link to them than try to out-do them.
Follow their guide until step 13 then refer back to this guide. http://www.ifixit.co...Teardown/4103/1
Posted Image
To actually remove the Internal SD Card (that is not soldered to the board but in-fact glued to it), I recommend you take an exacto knife (or other small blade or thin screwdriver) and slide it around the edges gently; once the edges are loose, take your screwdriver under the chip and just pop it up.
Posted Image
There will be adhesive residue on the board, I recommend using some gentle solvent to remove it (I used a cloth with a little paint thinner).
Put everything back together (just follow the iFixit guide on reverse) and feel proud that you are done with the hardware mod.
Partition your external SD Card
I used three partitions (all primary, not logical) , two 500 MB ext4 and a FAT32 with the rest of the space.
Linux users will probably not require much help on deciding what software to use, but for Windows users MiniTool Partition Wizard does a good enough job.
Do note that your device will perform according to your external SD Card, so it's not a bad idea to invest in a category 10 SD Card.
Modifing the ROM:
Download your ICS / JB ROM of choice, unzip it and open update.sh
Edit both line 31 and 35 to be as bellow
SD_PART='/dev/block/mmcblk0p3'Save and zip back.
Loading the Modded ROM to the SD:
Because we messed with the SD Cards, CWM will have a bit of trouble finding the external SD Card (until we flash our ROM).
Go ahead and connect your device to your computer and ADB the following command:
adb shell "echo /dev/block/mmcblk0p3 > /sys/devices/platform/usb_mass_storage/lun0/file"
That will allow you to access your SD Card from your PC, just copy your modded ROM to it.
Now, issude the following command:
adb shell mount /dev/block/mmcblk0p3 /sdcard
This will allow you to install the .zip file from CWM, go ahead and do that.
After checking partition types, your device will reboot and appear on a countdown to find the external SD Card, go ahead and reboot it manually before it does automatically (reboot to recovery with volume up).
Flash the .zip again, this time the installation will go successfully and you will have a working device.
Optionally, flash your desired Google Apps.
Now if we could get back to my original question, does anyone know why this device will not allow me to ADB it even when it's in download mode (a.k.a volume down/power button)
I actually got my tablet to boot up this morning for about 1 minute, then it shut off for no reason and did the "verizon" flash again when restarted.

priyana said:
Don't look at Overcome method if you have a CDMA tab.
It will only brick your tab if it ever worked at all.
Regarding bad internal memory, there are two chips. The OneNand 512MB and the MoviNAND 16GB.
If your OneNAND is the one broken, removing the MoviNAND achieved nothing.
The bootloader, modem, (and is it /system too of stock rom?) sits on OneNAND.
Click to expand...
Click to collapse
Please correct my but, what other then the modem.bin File could brick such a CDMA Device?
AFAIK as long as he picks the correct CDMA modem.bin it should work alright?
In the case that I am in error, then how does One recover such a CDMA Device then?

I can easily recover this device if I can get the ADB commands to start working. I feel like no one is reading the instructions. If you look at the link where the instructions are, there is a screenshot of his device. All of that "unable to mount" etc is what was happening to my device, hence why I removed the failed chip.
If I could get my device to show up in ADB, I wouldn't be asking this question!
By the way, I'm on an HP DV6. I tried all this in windows 8 and got nothing, so I installed a backup hard drive and put windows 7 on (this is what I'm on now) to see if that'd make a difference. Still nothing. I also tried on my old Gateway desktop but in download mode my old PC (still USB 1.1 1GHz celeron 512mb ram) the PC has no clue what the tablet is.

So I finally got this thing to boot into 2.2. Now the touch screen is unresponsive and the battery goes to 0 as soon as it's unplugged. Going to take it apart in the morning and make sure everythings connected. Might try a new battery but if this thing doesn't show more promising results soon I'm going to just say screw it and get rid of it.
Edit: Touch screen works but is flipped. If I slide my finger side to side nothing happens. If I slide it up and down i can awkwardly unlock the device. I'm guessing reload the factory image?!

the CDMA device is of different hardware. Not just the modem.
I am not technical enough to explain the difference. But I know Overcome method will brick it.
EliteEmerz: can you at least share how you get the PC to detect your device again?

priyana said:
the CDMA device is of different hardware. Not just the modem.
I am not technical enough to explain the difference. But I know Overcome method will brick it.
EliteEmerz: can you at least share how you get the PC to detect your device again?
Click to expand...
Click to collapse
If you put it into download mode it shows right up in my device list, drivers for "samsung USB device" load up. I can contact the tablet through heimdall to load bootloaders, images, etc.
For some reason I got it working pretty good last night except the touch screen issue. I reloaded the stock rom again and am playing with the SD card partitions since that's how I got it to boot up the last 2 times. I dont even care if I can load Jellybean on, I just want a working tablet.

By the way, this is SOLVED.
It will now boot up using a Stock ROM plus the zImage + recovery from clockworkmod
My touch screen is flipped (so I have to slide up and down to get it to swipe side to side) but at least it's on now. Made a new thread to address the flipped touch screen issue!!

Backup your device before flashing

Hi,
i have my x98 Air 3G (C5J6) a few days and iam testing some roms and windows installation, but the first thing i do, is a full backup of the device and it worked great and is simply easy, no TWRP or other things needed.
Be sure you have a 32bit Windows installtion on your PC or virtual machine, i used macrium reflect for imaging harddisk (the free version is ok).
Install Macrium reflect under a 32bit machine and make the rescue bootstick from the macrium (use GPT when ask).
You need also an USB hub (no active needed) and a keyboard/mouse and enough space on the stick (you can also use an ext. USB disk for backup but with his own power).
With this USB stick you can boot on the x98, press "esc" when start the x98, goto save/exit and go down to your shown stick (begin with UEFI).
now you boot to Macrium reflect und make an image of your x98 (the hole disk with all partitions!)
When something went wrong with an installation, you can restore your x98. But not the bios!
You can also separatly restore your windows or andorid parts. Windows is partition 15-19, all before is for android.
I have test it and it works fine.
Sorry for my very bad english but i hope you understand what i write

Excuse me , can you explain better
This sentence?
"With this USB stick you can boot on the x98, press "esc" when start the x98, goto save/exit and go down to your shown stick (begin with UEFI)."
Thanks
PS
Another thing... You think what possible make this operation by win10 (32bit) installed on teclast (with support usb stick) ?

Teclast X80 Pro (E3E6) Dual OS (Win10/Android 5.0): Remove Windows

Hey guys. Sorry to bother you in the X98 section, but since there's no section for the X80 yet and maybe the devices have some similarities, I hope it's ok.
The tablet worked fine, but to remove any possible bloatware under Windows or Android, I reset Windows. Somehow the device must have crashed (low battery?) and now I can't boot to Windows anymore (black screen and / or boot loop). Of course I made no backup / recovery disk. Android still works fine and I still get into BIOS / UEFI.
I tried reinstalling Windows via OTG with USB stick. I got to the point where I can choose a partition. Problem is, there are lots of partitions (Android, recovery, System and so on). I located the Windows partition, formatted / deleted it and tried to reinstall Windows on this partition. Just the exact way I would do it on a PC. Somehow it won't install on this partition. The error message says something about "the partitions are not in the recommended order. Further information for installation on GPT-volumes..." (I don't know the exact English phrasing because everything is in German). I chose "continue anyway". Then I get the message that "the EFI-system is not formatted in NTFS. Format the partition to FAT32 and start install procedure again". I press ok and get back to Windows Setup (Install now).
I also tried different repair and recovery options. One time I got error code 0xC0000034. Funny thing is, Windows still seems to be there because while trying to repair / recover I tried to load some drivers and could see the hard drives and folders under Windows.
I tried downloading the original roms here: http://pan.baidu.com/s/1qYEa8gc
You need a Baidu account for the larger files and after days and days I gave up to create such an account as it seems to work only with a mainland China number. There's an option for oversea mobiles but that's not working. I tried a QQ-account, but Baidu wants to link with it and you need that telephone number again. So apparently there's no way to get the original files that way.
I found some stuff here: http://www.needrom.com/download/teclast-x80-pro-dualboot/ but that's only a tutorial file in Chinese and some flash programms / drivers (also got them from Baidu - smaller files are possible to download without an account).
Long story short: I guess recovering Windows 10 is too much effort, so I want to make the tablet Android only and of course want to use the whole capacity for Android. I found a thread on reddit about removing Windows on the X98: https://www.reddit.com/r/teclast/comments/479eua/teclast_x89_how_to_remove_windows_10/
But I have no idea which partitions are definitely needed for Android and which ones I can safely delete. I found a partition map here: http://wheresmykeyboard.com/2015/08/teclast-x98-air-64gb-dual-boot-default-partition-map/ but that doesn't help me that much because they look different.
Attached you will find a photo of all the partitions on my device. I guess there are some which were created during the failed Windows installation because I had about 20 GB free space and now only 17.7 GB.
So is there anybody out there who knows if it's possible to remove Windows completely and which partitions I have to delete?

Did you ever figure this out? I just bought an X80 Pro and was thinking of doing something similar since I plan on making it an android-only tablet.

Deathgazer said:
Did you ever figure this out? I just bought an X80 Pro and was thinking of doing something similar since I plan on making it an android-only tablet.
Click to expand...
Click to collapse
Hi. Sorry for the late replay. Yes, I figured it out and my X80 Pro is now running Android-only with 32 GB. In the end, it wasn't that hard but a long way to success.

metalaxi said:
Hi. Sorry for the late replay. Yes, I figured it out and my X80 Pro is now running Android-only with 32 GB. In the end, it wasn't that hard but a long way to success.
Click to expand...
Click to collapse
Please do describe how you achieved Android-only with 32 GB memory
Cheers

metalaxi said:
Hi. Sorry for the late replay. Yes, I figured it out and my X80 Pro is now running Android-only with 32 GB. In the end, it wasn't that hard but a long way to success.
Click to expand...
Click to collapse
Yes please tell us how metalaxi , it'll be much appreciated.:good:

Ok, guys. Since some of you are asking how I did it, I'm going to try to explain it. It's kinda embarrassing that I don't remember the exact way but I hope it helps somehow. I used the tutorial from this site: http://techtablets.com/forum/topic/x80-plus-android-os-only/#login
Even though it's supposed to be for the Plus model, it also worked on the Pro. Btw, the guy Alex in that thread is me .
You can download all the files from my Google Drive here: https://drive.google.com/open?id=0BxEFqy4Rt9w_cnh3VG9ySk5sOHM
You need
- Android5.1 Upgrade Tool.rar
- X80 Pro (E3E6)- Dual OS - Android5.1-V1.04 Firmware.rar
- gpt.rar (Credit goes to Allember @techtablets-forum; hope it's ok to spread the file)
First you have to install the flash tool. Unrar the firmware and replace the gpt.bin. Then flash the firmware by checking BLANK.
Problem is that when I did all that, my Windows was already crushed and wasn't working anymore. I can't remember anymore if I erased the Windows partitions or any others beforehand. If you're not interested in Windows anymore, just flash it without changing or erasing any of the partitions. I guess by replacing the gpt-file, you do all that automatically.
I hope this somehow helps you. Feel free to ask for more help.
Have a good night!

metalaxi said:
Ok, guys. Since some of you are asking how I did it, I'm going to try to explain it. It's kinda embarrassing that I don't remember the exact way but I hope it helps somehow. I used the tutorial from this site: http://techtablets.com/forum/topic/x80-plus-android-os-only/#login
Even though it's supposed to be for the Plus model, it also worked on the Pro. Btw, the guy Alex in that thread is me .
You can download all the files from my Google Drive here: https://drive.google.com/open?id=0BxEFqy4Rt9w_cnh3VG9ySk5sOHM
You need
- Android5.1 Upgrade Tool.rar
- X80 Pro (E3E6)- Dual OS - Android5.1-V1.04 Firmware.rar
- gpt.rar (Credit goes to Allember @techtablets-forum; hope it's ok to spread the file)
First you have to install the flash tool. Unrar the firmware and replace the gpt.bin. Then flash the firmware by checking BLANK.
Problem is that when I did all that, my Windows was already crushed and wasn't working anymore. I can't remember anymore if I erased the Windows partitions or any others beforehand. If you're not interested in Windows anymore, just flash it without changing or erasing any of the partitions. I guess by replacing the gpt-file, you do all that automatically.
I hope this somehow helps you. Feel free to ask for more help.
Have a good night!
Click to expand...
Click to collapse
Hi @metalaxi. Do you think its possible to like "reverse" and use the same files to remove Android instead and maintain the Windows 10? Appreciate to hear from you. Thanks!

Do we have to change the gpt before doing what you said in your PDF? Or I have just to follow your PDF?

Hi guys, got mine a few months and want to get rid of the Windows part, but the instructions are insufficient for a joker like me.....
1. Download the firmware, its 4 parts of rar being zipped together
2. flash the firmware HOW?!?!?! I have no Idea...... please give us some closer instructions.

reycharlesconrad said:
Hi @metalaxi. Do you think its possible to like "reverse" and use the same files to remove Android instead and maintain the Windows 10? Appreciate to hear from you. Thanks!
Click to expand...
Click to collapse
Sorry, I can't answer that sufficent enough. As far as I know, you can just delete all partitions except the ones from Windows. Then format the unallocated space and merge it with the one from Windows. No guarantee!

dirkzelf said:
Hi guys, got mine a few months and want to get rid of the Windows part, but the instructions are insufficient for a joker like me.....
1. Download the firmware, its 4 parts of rar being zipped together
2. flash the firmware HOW?!?!?! I have no Idea...... please give us some closer instructions.
Click to expand...
Click to collapse
1. Which 4 parts do you mean?
2. To flash any firmware, you need to install all the upgrade tools:
IntelAndroidDrvSetup1.5.0
iSocUSB-Driver-Setup-1.2.0
PhoneFlashTool_5.3.4.0_internal_win32

metalaxi said:
1. Which 4 parts do you mean?
2. To flash any firmware, you need to install all the upgrade tools:
IntelAndroidDrvSetup1.5.0
iSocUSB-Driver-Setup-1.2.0
PhoneFlashTool_5.3.4.0_internal_win32
Click to expand...
Click to collapse
it's too long ago, so I don't know what I exactly did there, but since there was no reply for a long time, I just took a shot and worked out well, now I have an Android only tablet.
I just got lucky I guess....

partition help
Hi, please help.
I have x80pro e3e8
I managed to erase a complete disk partition.
You are trying to revive again, fail.
installed here:
iSocUSB-Driver-Setup-1.2.0
IntelAndroidDrvSetup1.5.0
PhoneFlashTool_5.3.4.0_internal_win32
downloaded here:
Firmware (20161020_SZ)
Tablet joined and tried to flash.
* failed - failed loadet.efi
Please help. I can not download from Baidu
* If I use phoneFlasTool and flash a blank disc - Create Flash partition and dual boot and replace recovery?
What to do with an empty disc?
Thanks for any advice

It is not so hard. By mine it was only trial and error. Installiert all drivers an go in the bootloader with three Finger method. Go two levels up and go into bootloader. Then connect to PC and look in Intel flashing tool if connection is reconiced correctly. Select the downloaded file and select flash. Thats it. Device will reboot and you are ready to go.

theone0987654321 said:
It is not so hard. By mine it was only trial and error. Installiert all drivers an go in the bootloader with three Finger method. Go two levels up and go into bootloader. Then connect to PC and look in Intel flashing tool if connection is reconiced correctly. Select the downloaded file and select flash. Thats it. Device will reboot and you are ready to go.
Click to expand...
Click to collapse
Thank you for the advice. That's right, I did it was marked. I found a reason. rom file was saved on desktop, and had a long name (as I downloaded it) It must copy the file to C've renamed the firmware. Everything went alright. I downloaded and used the GPT files for resizing disk and now goes all right. Thank you for responding to my question.

hi, I have problem while flashing.
Phone flash tool always gives ERROR
Automatic reboot is not supported on this device, please reboot the device manually
ERROR : [Port 0/1/4] Failed to reboot the device
Click to expand...
Click to collapse
Any idea what to do? I followed all the steps, tried many times, still same problem. And it's not possible to reboot device manually, because then it lose connection with PC

Restock OS Without Android
Hi there.
I have to restock my Device, but the Intel Flash Tool does not recognize my Device.
I cannot boot into Android to turn on USB-Debugging or go into fastboot mode
How do i flash my device without any OS installed?
---------- Post added at 04:03 PM ---------- Previous post was at 03:52 PM ----------
affe2000 said:
Hi there.
I have to restock my Device, but the Intel Flash Tool does not recognize my Device.
I cannot boot into Android to turn on USB-Debugging or go into fastboot mode
How do i flash my device without any OS installed?
Click to expand...
Click to collapse
Ok, got it working... dnx fastboot mode is there

....

hello guys by accident i deleted windows 10, how can i reinstall them? i dont have the windows 10 icon in the dual boot select i only see the android icon

mike mike baby said:
hello guys by accident i deleted windows 10, how can i reinstall them? i dont have the windows 10 icon in the dual boot select i only see the android icon
Click to expand...
Click to collapse
Straightforward if you can obtain a USB stick capable of storing over 7GB (some 8GB sticks may not); USB hub (ideally a powered hub); USB keyboard; OTG cable.
1) Obtain the Windows files of the correct firmware. The procedure outlined here is for E6E9 firmware, but other firmware will be similar. Download the circa 6.5GB E6E9 firmware Windows files from https://yadi.sk/d/XEvRsoiD3Q4vKX or https://mega.nz/#F!I0AXGR5C!YiNFkZL9DIvzepH28qAjEQ (or from appropriate source for your firmware version).
Decompress the downloads as required to obtain six folders and two files.
2) Format the stick to FAT32.
3) Name the stick WINPE (five uppercase characters).
4) Copy the previously mentioned folders and files to the USB stick.
5) Plug USB stick and USB keyboard into hub; plug hub into OTG cable; plug OTG cable into tablet whilst the tablet is off.
6) Turn on tablet and immediately start tapping << Delete >> key on USB keyboard. This should open the UEFI config section prior to Android boot option. If the tablet displays the Android boot option, turn off the tablet, wait a few seconds, then turn on and start tapping << Delete >> key on USB keyboard again.
7) When in UEFI, touch the title menu option of << Save and Exit >> and look in the << Boot Override >> section for the name of your USB stick, then touch the name of your USB stick. The screen will immediately go blank as the tablet starts to boot from the USB stick.
8) After a few minutes, a numerically display of progress will be displayed in a CMD window.
9) After reaching 100% and nearing completion of the overall installation, the tablet will prompt for acceptance, so accept that prompt.
10) The setup will run a few final operations for a few seconds, then automatically reboot.
11) Done.
You will be prompted to complete the OOBE on each Windows boot until you complete OOBE.