Registry changes not saving - Tilt, TyTN II, MDA Vario III General

Today, I noticed that my remapped PTT button was no longer remapped and I got that annoying message if I want to use PTT. I had it mapped to Vibraswitch and then voice recorder for holding. I looked at my registry settings and they were back to default. And the PTT key was recreated in services/ptt. I redid the settings then soft reset. When I turned it on my changes were once again taken off. Any one else have this issue?

vscout said:
Today, I noticed that my remapped PTT button was no longer remapped and I got that annoying message if I want to use PTT. I had it mapped to Vibraswitch and then voice recorder for holding. I looked at my registry settings and they were back to default. And the PTT key was recreated in services/ptt. I redid the settings then soft reset. When I turned it on my changes were once again taken off. Any one else have this issue?
Click to expand...
Click to collapse
I believe there are some registry changes that get automatically written when doing a soft or hard reset. There are some provxml files that based on their name automatically set certain reg entries. I'm not 100% sure how these work, but it might be your issue.
I would suggest writing a mortscript or something similar to run on startup, that time every time you reboot the script will change the entries back.

Related

Messaging hardware button not working (MDA)

The Messaging hardware button on my MDA Vario III is not working properly. When I press it, sometimes the top task bar shows "messaging" for a second, then disappears and the app does not start. Sometimes when I press it again, the messaging app starts after all, sometimes it does not. The strange thing is, that when I attach another prog to the button, it works flawlessly. I think that is is a software/registry issue, since this started after I installed AEBPlus. I deleted AEBPlus, but this has not helped. The only difference that I see in the registry is the first value, BTNWND. it has the value 2080975920, where all other keys have 0. I tried resetting it with PHM regedit, and it stuck for a few minutes, but after a while it resets to the old value again.
Does anyone know how to fix this? The registry key I am talking about is HKLM/Software/Microsoft/Shell/Keys/40C2.
I had a similar problem with my hermes on the original WM5 orange rom... but only if I had lots of apps open.
I would suggest that you experience this problem when you have left lots of programs running in the background.
Thanks, but I have no other apps running in the background. I have HTX X-button configured to close an app when I hit x. Strange thing is that the x-button does not close messaging when I hit x. I installed Pocket Plus and that x-button does close the messaging app.edit: SPB Pocket Plus, like HTC X-button, does not close the app properly, although it is not in the exclusions list. I have to kill it manually in the memeory/taskmanager app.
I played around a bit and noticed that the app is opened almost instantly when I go into settings-buttons, assign another app (Bubble breaker) to the button, then I close the button settings and the other app pops-up the second I hit the button. Then I go back to button settings, assign messaging to the button and when I press the button, I have the problem appearing again. It works this way till a soft reset. After the reset, the button does not work at all, untill I first assign another app to the button and then re-assign the button to messaging. Very strange behaviour. Can someone perhaps post the values in their registry ( the key is HKLM/Software/Microsoft/Shell/Keys/40C2). My value there differs with every soft reset, but is always something like 2080960048. When I set it to 0, the app opens instantly when I press the button, but for some reason after a while it resets to a value like 2080960521.

Vibrating dial pad buttons

On my old ETEN M600 (RIP) I had a phone pad app/skin that gave me big buttons and when a dial button was pressed the phone vibrated for a 1/4 of a second. It was great physical feedback to feel that little blip when a button was pressed and I believe it allowed me to dial numbers quicker. Anyone know of a app that enables this for the Tilt/Kaiser?
And yes I did a search for this before I posted a new thread.
Thanks
OT
How to set up one button press on/off with device and screen locked
Also for those that are interested. I have AE Button Plus, Ilauncher and DeviceLock by Matt Armstrong installed on my Tilt. The combination of these programs allow me to program the left softkey to turn off the Tilt. Matt's Devicelock auto locks the phone and prevents any other buttons to be pressed. When I want to use the phone I can press the left hard key that corresponds with the left soft key and that turns on the phone and unlocks it with one button push. This set up gives me one button off/on and all other keys and the screen is locked from accidental button pushes. Now I just wished that Devicelock would shut off the phone after 10 seconds if not unlocked. Right now my phone is in my pocket and if I accidentally push any button other then the left hard key my screen will turn on in a locked state and time out only after 1 minute if no other buttons are pressed. I would like it to turn back off faster.
BTW Thanks Matt
Not an app but it can be done with registry tweaking:
[It involves modifying registry keys so beware].
Navigate to HKCU\ControlPanel\Sounds\
In here there are a bunch of keys named Dtmf which represent all the keypad keys [0-9, #, *]
Rename Standard DWORD parameter Sound to Sound1
Create new String Parameter Sound
Assign value *vibrate* to this new parameter.
Save and exit, test it, then go back and do the same for all your keys, sorted.
A .cab for this?
Is there a .cab floating around for these reg settings?
It would be a great contribution to the community if someone could whip up a cab to make these reg changes ;-)
Wow, now that was usefull. I had installed some small prog to do the same, but it didn't work great. It wouldn't vibrate unless you pressed for a more than 250 ms. This mod vibrates immediately! Thanks!
someone should tell Kaisertweaks that that needs to go in
Here you go, working great on the TyTN II
That's what I'm talking about
Gizmo5148 said:
Here you go, working great on the TyTN II
Click to expand...
Click to collapse
Thanks Gizmo!
I love this place. Where would WinMo be without xda-developers???
Any chance you could upload the .cab directly instead of zipped? For some reason it won't extract on my tilt and I can't get to a PC tonight.
Thanks again.
Sure thing, here you go
Installed and it is working great. This is really a great tweak!
aren't dtmf tones what are used for things like voicemail and such? like "press 7 to delete" it recognizes the sound? does this affect that at all?
I don't think this tweak has any effect on dtmf tones. I just tried my VM and everything worked as usual.
strange...i installed this on my tilt (htc rom) and when i touched a button there was no vibrate, until about 5 seconds later, it was delayed i guess, and after that i never felt another vibrate, even after a few resets.
bump.
would like to get this working.
Will this make it beep and vibrate or just vibrate? It would be cool it it could do both at once!. Also, maybe post cab to revert back to just the sound in case anyone wants to change it back?
Mikeeey,
Try holding the number down a little longer. If you just touch it, it will display the number but not vibrate.. I had the same trouble also.
I do appreciate the afford, but shouldnt it just work when it notices a keypress, not a long keypress.
You have to hold it for a little time. Thats how it works
Gizmo5148 said:
You have to hold it for a little time. Thats how it works
Click to expand...
Click to collapse
That's how the cab file works. But when I did the registry edits as listed in the 2nd post, then it is an immediate vibrate. I used to use the cab file version. I removed that and went with the direct reg edits. Now it vibrates immediately.
jomo25 said:
That's how the cab file works. But when I did the registry edits as listed in the 2nd post, then it is an immediate vibrate. I used to use the cab file version. I removed that and went with the direct reg edits. Now it vibrates immediately.
Click to expand...
Click to collapse
Same here, works great after manual reg edit.
dalewinterstein said:
Mikeeey,
Try holding the number down a little longer. If you just touch it, it will display the number but not vibrate.. I had the same trouble also.
Click to expand...
Click to collapse
thanks for pointing that out dalewinterstein, it works for me now.
i did the manual reg edit to try and make it respond faster but it doesnt, actually the keys lighting up after being pressed dont respond fast enough to my presses, does this happen for anyone else? i mean if i hold it just a bit longer it will light up and vibrate but im normally faster than that.

AT&T Tilt PTT Remap Solution

I searched all over the place to remap the PTT Button on my AT&T Tilt without altering the ROM. I don't use or want to use Push To Talk services which made the PTT Button useless, Remappers weren't working and the PTT settings screen kept poping up every time I hit the button.
So I tried the following solutions:
1: How to assign a shortcut to EndKey, SendKey, Power Button, PTT Button!!
+ This allowed me to assign another program to the key (Voice Command, Short_PTT.lnk). And it worked fine.
- However, the PTT Settings kept popping up also, though it would go away if I just ignored it.
2: Cingular ROM users: PTT function hacked!
+ Though this is not really for the Tilt/Kaiser, and it would not accept any remap in accordance with its directions, it did disable the PTT Settings program from rearing its ugly head.
++ Combined with solution 1 above, this button does exactly what I want it to do!
Thanks to the 2 contributors, HMA4 and SLEUTH255, Cheers!
NiteStalker said:
I searched all over the place to remap the PTT Button on my AT&T Tilt without altering the ROM. I don't use or want to use Push To Talk services which made the PTT Button useless, Remappers weren't working and the PTT settings screen kept poping up every time I hit the button.
Click to expand...
Click to collapse
Did you delete the PTT registry entry? Otherwise, your remap won't stick.
What I did was
1) delete the PTT registry entry
2) remaps the button using SPB Pocket Plus.
I searched but could not find the registry entry, and I have pocket plus, remapping wasn't working, probly due to the registry (and I'm not very comfortable editing that anyway). This has stuck through several resets, and can be uninstalled if i wish, maybe you could elaborate because I may not understand any negative implications in this method.
I'm pretty new at pocket PC's.
Thanks.
Here ya go!
NiteStalker said:
I searched all over the place to remap the PTT Button on my AT&T Tilt without altering the ROM. I don't use or want to use Push To Talk services which made the PTT Button useless, Remappers weren't working and the PTT settings screen kept poping up every time I hit the button.
So I tried the following solutions:
1: How to assign a shortcut to EndKey, SendKey, Power Button, PTT Button!!
+ This allowed me to assign another program to the key (Voice Command, Short_PTT.lnk). And it worked fine.
- However, the PTT Settings kept popping up also, though it would go away if I just ignored it.
2: Cingular ROM users: PTT function hacked!
+ Though this is not really for the Tilt/Kaiser, and it would not accept any remap in accordance with its directions, it did disable the PTT Settings program from rearing its ugly head.
++ Combined with solution 1 above, this button does exactly what I want it to do!
Thanks to the 2 contributors, HMA4 and SLEUTH255, Cheers!
Click to expand...
Click to collapse
Here's mine,
1)Disable PTT (Credit to vpoet)
2)In the registry navigate to the hklm\services\ptt
Back it up and delete it (yes the entire key)
3) Install cab
It'll map a new button 6; (two functions-button 6 press and button 6 hold) and also allow you to change whatever is on the button using the button menu in settings.
(It's default icon for button 6 is Voice Speed Dial, and button 6 (hold) is record, but you can change either key to what you want.)
Alemaker
Thanks, I didn't know that I could remap it with SBP Pocket Plus, but it works like a charm.
actually, i found this to be the absolute simplest solution available (no programs, just three registry tweaks):
http://tiltsite.com/2008/02/remap-that-ptt-button/
is there a way to remove PTT from 'Programs' also?

Remapping Right Soft Key in Touch-IT v3.01

I have tried searching for a long time on this because I know I've seen it before, but I can't find it anywhere.
Where is the mapping of the right soft key in the registry? I'm using itje's Touch-IT v3.01 and can't find it anywhere. I don't want the right soft key to be the "Today" screen, but any changes in settings do not "stick."
Hi
Use Advanced_Configuration_Tool_v3.3
Remap softkeys
Dinesh
ADC doesn't change the TF3d right key very well..
It's better to change the registry keys.
Use a decent regeditor (I use fdc taskmanager)
go to HLKM/software/htc/manila
the right and left softkeys are there.
You need to put the complete path to whatever file you want to access and enclose it in ""
HtH
Ok, so I got there, but I really don't want to map it to a path. I just want it to function like the left soft key, but on the right. I looked at the values of the LSKpath, but it is blank too.
If I changed the registry value to "<Right Softkey>" like it is called in settings-buttons-left key, would it still work? I'm a rookie with the registry although I am trying.
And I have the fdc task manager now.
try this little app, works perfect
http://forum.xda-developers.com/showthread.php?t=452505
Yeah, that tweak app lets me assign something else, but I want the right soft key to be context with what I'm running on the screen.
... but still good work! I love your ROM.
do you mean the right Hardware key then?
Yes. Sorry for any confusion... I am talking about the hardware key.
In that case again there's a reg key that you can change,
but have you tried it in the button settings control app? as I've just tried it and it works here using Itje's rom.
<Right Softkey> is one of the options and it sets it fine. Not tested to see if it sticks after soft reset but it works.
anyway reg key is HKLM/software/Microsoft/Shell/Keys/40C3
using the buttons settings control panel changes
Flags to 14 (decimal)
Default (blank as in nothing there)
HtH

[SOLVED] Buttons randomly messed up

Quite randomly, the start, OK, and application shortcut buttons on my Orange tytn ii have stopped working properly.
In ScummVM, I can use them as normal, they're not DEAD, but they don't do what they should. The start button doesn't open the start menu, the ok button does nothing, and the application shortcuts seem to think they're the softkeys...
Yet the softkeys do as well.
I suspect scummvm of having something to do with it, it only started after I remapped a key I was using in that.
So, does anyone know of this problem?
If not, do you think it's likely that ScummVM is changing registry entries or something to prevent windows from intercepting the keys then changing them back on exit, and not done it for some reason?
It's got to be as easy as changing some registry keys, I just don't know which ones and what to.
Thanks in advance
Hmm, after re-setting all the buttons in the "Buttons" control panel they're working again. I'll just put this down to general windows annoyances.

Categories

Resources