Hi all,
I hope you can help. Whenever I connect my bluetooth keyboard my keys on front of the diamond will be disabled. After disconnecting the keyboard they will work again. How to disable this? beceause now whenever the keyboard is connected I can't use de answer, hangup en navigation keys on the diamond.
thanks.
right now that seems to be how it is. when you say you have to disconnect the keyboard what do you mean by that? I'm guessing you turn off your keyboard right?
What I do is that I just toggle the bluetooth radio by turnning it off and on again. that will break the link between the keyboard and the phone and allow you to use the keys again.
Yes you'd have to do this pretty much everytime after you're done with the keyboard.
irritating.
Yup I mean turning off the keyboard. There must be a registry sollution for this.
Related
Ok this may be a dumb question but I have been searching for the answer and can not find it any where. I want to unlock and have the screen come on( comeout of standby) by sliding the keyboard out.
Like when you flip out the screen on the side kick.
I have the 2.17 custom rom by xelencin if that helps.
Thanks
I really want that feature too!
To add a same thing to your question, can i unlock the machine with one hand?
I have smartkey installed but everytime i try to unlock the screen, it said I have to press Unlock, and there is no way to press it with a softbutton, i have to either do it with a stylus or the keyboard....
baraider said:
To add a same thing to your question, can i unlock the machine with one hand?
I have smartkey installed but everytime i try to unlock the screen, it said I have to press Unlock, and there is no way to press it with a softbutton, i have to either do it with a stylus or the keyboard....
Click to expand...
Click to collapse
why not use your thumb?
huangyz said:
why not use your thumb?
Click to expand...
Click to collapse
and leave fingerprint smurk on the screen you mean?
The only problem I could see with sliding to turn on / unlock etc is that the magnetic catch on the standard case would then activate the switch on etc... I'm sure it would be possible to intercept this trigger in some way even when the OS is in standby but I can see issues with the device turning on when used with the standard case...
The screen doesn't rotate when you open the keyboard until aftr the device is turned on, which suggests to me that the position of he keyboard isn't monitored by the device when it's switched off. If this is the case ten it would be impossiblt to have the keyboard switch turn the device on.
Correct me if I'm wrong.
Yep, pretty sure sliding the keyboard out does not create a wakeup event. It is possible that something like MortSaver could be used to mimic this function - that's a program that turns off the screen and locks the buttons when you press a hotkey - i.e. it doesn't put the device into standby, it just kinda puts it into low power mode. I'm pretty sure that could be rewritten to turn the screen back on when the keyboard slides out. Perhaps if you plead with the author...
Is there any tweak to disable powering on the device when slide the Keyboard?
I always put my tilt in my pocket and it power by itself when keyboard slide by mistake... any help?
I've noticed this as well, quite annoying...some kinda fix would be awesome.
Greets,
While the subject line really says it all, I have intermittent luck with getting the little picture of the keyboard at the bottom of the screen to actually bring up a keyboard.
Does anyone know what this may be, and how I can reset it (without a soft reboot). I can get it to bring up the selector (which lists the screen keyboard as active), but I cannot actually bring up the keyboard.
Thanks!
Hhmmm
I say try a hard reset...I know that's a sucky thing to do ....but I think it will fix you problem
Hello
Does anybody know if it is possible to set vibrant signal for the virtual keyboard press? How?
zoltancsapo said:
Hello
Does anybody know if it is possible to set vibrant signal for the virtual keyboard press? How?
Click to expand...
Click to collapse
i think this might have been discussed before in other forums. you may want to do a search on this and i believe you can find the results.
just out of curiousity, why would you want to activate vibrate effect for keypress? you are using 1800MAH battery?
Here
Heres an app that works fine with my Diamond. He's right, though, battery conservation is crucial on this phone, unless you can charge it all the time, like at work in the car, etc. Here it is anyways.
View attachment KD8DNS_KEYPAD_VIBRATE.cab
vibrate keyboard
just loaded the vibrate phone pad vibrate cab, I was hoping the the keyboard for texting would also vibrate.
Is this possible to change
lenaddison said:
just loaded the vibrate phone pad vibrate cab, I was hoping the the keyboard for texting would also vibrate.
Is this possible to change
Click to expand...
Click to collapse
same here.
Unfortunately the display of my Diamond broke and now i can't use it anymore (touchscreen didn't work - phone still works (booting, ringing etc)). I want to make a backup with Active Sync and MyMobiler, but everytime I connect the Diamond with my PC it only starts the access to the in-build flash-memory. I cannot change the behavoir for starting in Active Sync-Mode on Diamond.
What can I do?
Screen acting weird.
I have a problem with my screen too. Sometimes I cant use my touchscreen anymore. When I turn off the screen and wait a little bit I can use it again. But lately another problem has occurred, my screen keeps on loosing its alignment.
Its almost like my screen is dying...
i recently had the same problem...my fone was fully functioning all apart from my touch screen itself... i had to painfully keep runing the screen alignment an now it is fine
The only solution I could think of would be to put a registry file containing the ActiveSync setting [instead of 'connect as removable drive'] onto the phone and try to start it using the hardware buttons.
Unfortunately, I couldn't get into the start menu without the stylus. But the hardware buttons allow you to scroll through the TouchFLO tabs so you're able to access the programs tab. Maybe you've assigned explorer or activesync to one of those buttons? If not, you're able to assign one even w/o the stylus. I failed to re-enable the settings tab so I don't know what's on it. Maybe that one helps, too.
When you connect your device to your PC you can change you connection optons with the hardware buttons. This way you can set it to activesync. this has also been my solution to get to the screen alignment settings via mymobiler. But now I need to get a stock dutch SPL so I can return my phone to repair the screen. I dont carry my laptop around at all times...