GPS problem - Touch Diamond, MDA Compact IV General

First time i had used Goole map en tomtom 7 that was good adn my diamon found gps satellites. But now programs are finding the reciever but do not find any satellites. I made 4 hard reset and now it is the same "nothing". Is there someone who know how to fix it.
Thanks
Ps: I am belgian so excuse me for my english, I am doing what I can

same problem to me with navigon navigator 6. it automatically found the gps device but no satellites.
check the baudrate! it has to be 4800

All is good ( and at factory default ) COM 4 and 4800 but no signal in any programs (google map, IGO 8 , TOMTOM 7 , GPS positionning for wifi site survey)

I had make a new hard reset and reused goole map all good and reinstall IGO 8 and all good but I hope it will not change a new time. For IGO 8 I had used the normal install and not changing any thing but it used port 4 at 57600 for running. If something chang in a few days and no gps signal and satellites again I will post a new question. That is not as simple as a PDA with internal or external antenna with SD.

dge669110 said:
All is good ( and at factory default ) COM 4 and 4800 but no signal in any programs (google map, IGO 8 , TOMTOM 7 , GPS positionning for wifi site survey)
Click to expand...
Click to collapse
What's your settings in Settings/system/external GPS?

settings:
programmes : com 4
material : none and 4800
access : gps auto gestion "on"

@ dge
Het is ook mogelijk dat je het programma QuickGPS even moet runnen voordat de sateliet gevonden wordt. Om de 6 dagen even opnieuw downloaden.
Let me know..

sorry I do not speek weel deutsh and I had not undestand all in your reply. can you tell me that in english or french. This time I am not using the update of GPSquick but I can try and see. If you know how to disable it tel me too.
And excuse me spikelee I realy need to learn néderlands

dge669110 said:
settings:
programmes : com 4
material : none and 4800
access : gps auto gestion "on"
Click to expand...
Click to collapse
What about trying to change to first tab com2, second tab com4 4800, that's my setting and it works on all mentioned programs. I've selected com2 in TomTom.

I have not try because tomtom 7 just select for me the config and do not let me edit the settings, I will try on the divice only and tell you. but I notice that the 2 times that I install fring I had lose my GPS signal, the GPS is still detected but no signal.
Thanks to everybody

Could it be that you've enabled the Assisted GPS (for example with Schnap's advanced configurator?). I've read that this could cause some problems as well.

I have not enable A-gps and not downloaded QuickGps info. The last time that i used Advance config, just after the install my phone was realy slow without touching anything in config. But I do not know the difference between A-GPS and QuickGPS in the tabs.

dge669110 said:
I have not enable A-gps and not downloaded QuickGps info. The last time that i used Advance config, just after the install my phone was realy slow without touching anything in config. But I do not know the difference between A-GPS and QuickGPS in the tabs.
Click to expand...
Click to collapse
Don't know the exact difference either, so from what I've understood: QuickGPS needs information from the internet in order to be able to get a quick fix as it knows more or less where you are from the GSM antenna's you connect to. AGPS helps in case there is no or bad GPS reception to get more or less a fix.
QuickGPS is functional and really helps. AGPS is not necessary in my opninion.

205_lacoste said:
Don't know the exact difference either, so from what I've understood: QuickGPS needs information from the internet in order to be able to get a quick fix as it knows more or less where you are from the GSM antenna's you connect to. AGPS helps in case there is no or bad GPS reception to get more or less a fix.
QuickGPS is functional and really helps. AGPS is not necessary in my opninion.
Click to expand...
Click to collapse
I agree with you.

When I am using Quick GPS I am getting in some trouble with GPS but I will Try with other config like someone say earlier. For the moment I am Using tomtom7
and I will Install fring in few seconds + Wififofum and see if there is any think that change. After I will use QuickGPS and see.

dge669110 said:
When I am using Quick GPS I am getting in some trouble with GPS but I will Try with other config like someone say earlier. For the moment I am Using tomtom7
and I will Install fring in few seconds + Wififofum and see if there is any think that change. After I will use QuickGPS and see.
Click to expand...
Click to collapse
Quick GPS dont uses the gps hardware, it just downloads the position of the satellites for 6 days in advance. So your gps device knows where to look for the satellites.

for that I was reading somewere to use " othe NEMA " and it is finding directly GPS satellites so no need to wait 3 min for good GPS signal and it is working realy fine. There is only com 4 and com 7 but on com for its good, in IGO 8 that is 57600 baude on com 4 with internal and I do not know if I can use 57600 without killing my GPS antenna. For the moment all goes right and I hope it will continue, the first time that I experienced problems that was 2 after using prog or soon after a hard reset.
Thanks for those explainations and helping me, Iam sure that it will help other guys to.

oops, my bet.
Before you try change the setting(witch i believe must be correct) you have te run the QuickGPS prog. When downloaded it will give you a valid time(i think 6 days and a couple of hours). If you don't refresh this it won't work..

Related

GPS Fix Problems (official HTC ROM)

i have problems with Satalite FIX.
it can take mor then 10-20min (if at all) to get a fix.
i setup my GPS manualy to COM9 @ 4800.
i know (at least) one other user have a simular problem.
HTC, after some e-mails, say that if i DON'T use TomTom software, they can't help my with this isue.
any idea ?
thanks.
Fix
I had some problems with slow fix. I enabled the GPS applet in settings and it was configured at 33600, changed to 4800 and also in Tomtom and miomap settings configured to 4800, after that, very quick fix, on cold start less than 1 min, on warm start just seconds. Try it.
under, settings -> connection -> GPS ...
i set:
program tab:
GPS Program port = GPD9
hardware tab:
Port = com9
boud = 4800
access tab:
mark on the manage GPS Auto.
is taht OK ?
and allso on the navigation program i set manualy com9 @4800
Yep, that's my config and works right...
interesting... i have my settings as follows -
program tab:
GPS Program port = GPD1
hardware tab:
Port = com1
boud = 115200
access tab:
mark on the manage GPS Auto.
with these settings i get a fix in 30 sec to 90 sec...
cortezzi said:
with these settings i get a fix in 30 sec to 90 sec...
Click to expand...
Click to collapse
After a sofreset? Probably not
The "warm reset time" in a GPS is not related with the Port number or the baud rates...but with its sensibility
SAme for me the GPS response can take up to 10 minutes.
I tried your setting Julioski and AriebK but it doesn't help?
In tomtom I don't see where to set the port and the baud speed can you help?
Any other ideas?
after configure the above settings, i get FIX, but after 20-30min of navigation... the FIX is gone, one more thing, i notice that my phone 3g signal drop allso, SR was nedded.
ariebk said:
after configure the above settings, i get FIX, but after 20-30min of navigation... the FIX is gone, one more thing, i notice that my phone 3g signal drop allso, SR was nedded.
Click to expand...
Click to collapse
According to HTC the reason the GPS function was not enabled in the first place was a conflict with the GSM signal,anyway try manually setting your phone band to GSM and see if that makes a difference.(Settings,phone,band,select network type:GSM)
What radio version have you installed?
1.35, 1.38???
I have an HTC p3600 Trinity and have also just installed the newest ROM from HTC.
I downloaded the TomTom application from HTC, installed it and everything "seems" fine accept I cannot acquire any signals.
I have tried many of the different GPS settings from the GPS manager, but nowhere do I see a way to change what TomTom is looking for. There are 5 default gps reciever options... (builtin, bluetooth, wired, other bluetooth and other NMEA device) and I really have no idea what to choose if I have to input the settings.
Can anyone help?
Thanks!
PAR
par02 said:
I have an HTC p3600 Trinity and have also just installed the newest ROM from HTC.
I downloaded the TomTom application from HTC, installed it and everything "seems" fine accept I cannot acquire any signals.
I have tried many of the different GPS settings from the GPS manager, but nowhere do I see a way to change what TomTom is looking for. There are 5 default gps reciever options... (builtin, bluetooth, wired, other bluetooth and other NMEA device) and I really have no idea what to choose if I have to input the settings.
Can anyone help?
Thanks!
PAR
Click to expand...
Click to collapse
Both the "built in" and "COM9" should work (and do for me).
Make sure you're in an open area, and give it enough time to acquire a signal (could take 10 mins).
According to HTC the reason the GPS function was not enabled in the first place was a conflict with the GSM signal,anyway try manually setting your phone band to GSM and see if that makes a difference.(Settings,phone,band,select network type:GSM)
Click to expand...
Click to collapse
i tryed that... seems that with GSM, it took much more time to get a FIX (if so)...
with GSM it get the FIX much faster, but stil... too much and it drop the signal without any reasone.
What radio version have you installed?
1.35, 1.38???
Click to expand...
Click to collapse
1.38.00.11
I have the same exact problem, sometimes GPS gets the satellites in 30 seconds sometimes no satellite after 15 minutes. This of course in the same location...
This is really anoying, any other ideas ?
PS: I am using the french version!
daghood said:
PS: I am using the french version!
Click to expand...
Click to collapse
Maybe that's why ... sorry couldn't help it...
Are you sure there aren't any other factors involved (like heavy cloud cover, rain, , etc.?) or more than 3 days since last fix (not that this should take 15 minutes - this is more than downloading the whole almanach). Can you check if you have signal all the time, or if you keep loosing all satellite signal? Because if it looses all satellites, he has to start from the beginning with the fix, so it's in a loop until he gets proper signal.
Well there seem to be quite a few issues with the GPS,personally i'm using the Destinator 6 software ,and here is what i noticed ;
With the official HTC rom :
The software detects the GPS in about a minute and acquires a fix in about 3-4 minutes with the GSM on and a clear sky.
If i softreset the device then 1/3 times it won't find a GPS antenna and i have to manually reconnect and define the com port,it then takes apprx 5 minutes to get a fix.
The weird thing is that when i used Destinator PN i didn't have any of these issues .
Lately i've started using img-32424-mUn and i've noticed a definite improvement in both GPS strength and speed.
i did use following test rom, the gps response is around 1min.
RUU_Trinity_CHT_1.23.751.1_101_6275_1.29.00.11_108_Test.exe
however, by using offical rom whatever config the baud rate or GDP, required 8-10 to get the fix.
the problem is that it's not stable
one day i get a FIX within 1 min, next day after 20...
and 2 days later, not getting any FIX.
i tryed with GSM and 3g ...
i guess the radio (or the GPS part) isn't as we excpect it
sad that HTC dont want to support users that NOT use TomTom.
I think it would be useful if each of us told the others the type of GPS software they were using as it (The GPS software)seems to affect the time it takes to acquire a signal.
Also try using the GPS with and without the radio (Flight mode) and see if it makes a difference.
No GPS Signal & Icon
Hi! I've another problem. I've downloaded new ROM upgrade and Tomtom applications. After waiting for 10 minutes, my device says no signal received. I read from some forums we can adjust some variables but there is no GPS icon under settings\connections folder.
Can anybody help me! I have version WWE 1.23.405.

help with gps on kaiser

ive got a kaiser and i cant get GPS to work.it asks for external connection.surly theres a setting for on board.i have copilot 7 legit software.im on o2 network pay&go.any HELP WOULD BE APPRECIATED
mattdehat said:
ive got a kaiser and i cant get GPS to work.it asks for external connection.surly theres a setting for on board.i have copilot 7 legit software.im on o2 network pay&go.any HELP WOULD BE APPRECIATED
Click to expand...
Click to collapse
Uggggghhhhhhhhhhhhh! SEARCH SEARCH and SEARCH!
Make sure you have GPS set to something like "internal GPS" and the baud rate set to 4800 and the COM port set to COM4.
gps
found setting still no go.struggling
I had a hiccup with the GPS lately. I installed and ran "GPSTest" and it helped sort things out for me (can be found in this post).
It may take 3-30 minutes to get a HDOP score (as mentioned in the linked post), but at least you'll know your GPS receiver is functioning properly. Then you can address the Copilot issue.
gl
gps probs
hi installed this prog and 1hour later still no gps function,the prog is just trying to find signal to no avail.please help
run quickgps, hit download, then start ur gps program......and go outside
done this already.still no gps signal.tried set up again and again.works fine via bluetooth receiver.might as well of stuck with xd2i for all this hastle.getting cheesed off.more help needed and much appreciated.thanks
This Is Now Solved Many Thanks TO XtreMe_G for prog link and Once Again To All At Xdev
I had the same problem with the gps not receiving a signal, I had to wait 15 minutes the very first time, now it connects after a few minutes everytime!

Intermittent GPS

Hi all, yesterday i've changed the "external gps settings":
COM8 For virtual GPS port and COM 4 as Hardware GPS port, baud 9600.
Today i was using my GPS the first time after the settings descripted before...
The GPS Works, but at regular intervals of 2 sec, then stops for 10 sec (No GPS Found with Tomtom) and works again.....
Now i have 3 questions:
1) Can i solve this WITHOUT an Hard Reset??
2) If i disable the Virtual com port, tomtom DON'T let me choose another COMport (it skips the Comport configuration page) and, when it allows me to select the right port, the COM4 isn't there
3) There are A LOT of comport into "External GPS Settings", some starting with COM..X and others ports named GPD..X ..... What type of ports are??
(Ps: i have already installed tomtom again)
Did you try to disable AGPS?
I have only seen this problem when AGPS is enabled (via advanced config) too
Also the defualt GPS COM ports is 4 and baud rate of 4800 (should be no need to change this) and why mess with external GPS settings when the device has internal GPS?
I have same problem on iGO8 with AGPS enabled.
You guys are right! The A-GPS was ON (strange, i don't remember i've activated it)
If i play with the external gps app is because i would to share the same com port to 2 gps apps.....
BTW when i set the com4 in Hardware port, reopening the app it disappear.
Now i have Agps disabled, External gps app "void" and tomtom don't let me choose the comport (it switch from baud speed to mainscreen)
Hmm, I had no problem at all using GPS at standard settings for:
Igo
TrackMe
GoogleMaps
at the same time!
Riel said:
Hmm, I had no problem at all using GPS at standard settings for:
Igo
TrackMe
GoogleMaps
at the same time!
Click to expand...
Click to collapse
diamond has disabled agps out of the box.
Hmmm I had no problems the first couple of times I tried iGo when I first got the device. Then I tweaked it, enabled AGPS and all hell broke loose (presumably due to this setting, though not 100% sure since I changed lots of things). Disabled it on my own, trying to back-track, now it's better but I still got problems with GPS lost...
By the way, is there any use setting COM4 to high speeds? Does it reall improve performance?
I had the same problem after flashing the actual rom build from HTC club. I am currently sticking to this one in italian and no problem at all.
P.S.: Just noticed you're from my same city
All ok now, i suppose that if we leave blank the GPS port (no HW port) into first COM screen of external gps app, tomtom skip the comport settings screen, and don't allow you to choose another one.
I've Hardresetted my pda yesterday, and i've seen that out of the box, the diamond has COM4 selected by default.
I don't want to change anything now (i have no time in those days to do another Hard reset) BUT, if you have problems regarding the GPS COM Settings screen in tomtom, try to set the COM4 into GPS PORT (not hardware port) of the "External Gps" app.
hello everyone
i have the same problem of signal GPS lost and coming back after a few minutes of use (i use IGO 8), then lose again, then back again, and so on.
I installed the new flash rom from HTC eclub, (QMR-RUU_Diamond_HTC_FRA_1.93.406.1_Radio_Signed_Diamond_52.29.25.12_1.00.25.05_Ship.exe)
Even if i disable the a-gps using advance config, the problem is still there.
Do you think that problem comes from that new HTC ROM ?
Any solutions?
NO... I had the same problem on old ROM very rarely and solved with Quick GPS , I will see if the problem persist on new ROM...
I had this disconnecting problem too with Tomtom 7,
now with Bepe 0.98 and radio Radio v1.00.25.07, all is OK, no disconnect at all this morning ( 2 hours of GPS use ).
But I don't know what resolve the problem, Bepe's ROM or the new .07 radio
my diamond refuse to accept setting for hardware port and rate......
it always displayed the default (hardware none ,,port 4800)
and always intermittent gps signal...
can u help me?
hmh79 said:
my diamond refuse to accept setting for hardware port and rate......
it always displayed the default (hardware none ,,port 4800)
and always intermittent gps signal...
can u help me?
Click to expand...
Click to collapse
Never mind the setting. Is AGPS disabled?
yes its disabled...
A bit strange, mine works perfectly with iGo, it even updates the position (almost) continuously when in pedestrian mode.
Perhaps you could try an auto detect from your GPS program to reset the link. By the way, what soft are you using?
well im using garmin xt and navigon...garmin display that the program and hardware is com:4
thank u for being patient with me....
I know Garmin works on the Diamond, so I'm running out of ideas... I remember reading that some VOIP programs screw the GPS. Did you install any such program?
If not, what I would do is back up my contacts and calendar and do a hard reset to see if this solves the problem. A bit painful, but will certainly answer the question whether there is something wrong with your hardware or not.
well.. i have changed the rom to karmba version, and it works fine for the last 6 hours..
gps functioning well.
may be the fault was in my previous rom (SwiftBL-WWE-Diamond-ROM-v5-5-Lite)
thank you very much for your help

(SOLVED) GPS Solution for Diamond- Cooks please look

Hi everyone
I have spent a lots of hours searching for the answer to bad gps reception on diamond, through different forums.I was about to sell the diamond when I finally came with a solution and that is Hard Reset after each Rom flashing.
For a few days I could not get a gps fix, no matter what I did. I tried Quick gps, Gps tool , Google map, iGo8 and Garmin. Somewhere I read that it could be the Rom I am using. So today I flashed 4 different roms including Dutty's, bepe and panosha but no gps fix. Finally I did a Hard reset and viola, it found the satellites within 10 seconds inside near the window on all the different Gps softwares without any problem.
So here is the procedure:
***After a ROM flash finish the usual soft reset and stuff and then do a HARD RESET. Download the data through Quick Gps and your gps should work properly at its default settings.***
Actually I found that Diamond is faster than TYTNII for getting the Gps fix.
Now if the Cooks can find out what causes this behaviour so we do not have to do a hard reset after every new flash.
Please share the findings.
Cheers!!!
********* Ok I have been flashing all the new roms and Gps was not working even with the hard reset. Finally I flashed CT's Beta lite2 Rom, did a hard reset and viola Gps is working flawlessly for the last three days. This Rom is actually the fastest and very clean among all the other roms I tried ( no offence to all the other great Cooks ). Please try it and share your findings!
Well, now i know why i dun have GPS problems...
i hard-reset after each flash ... just a habit inherited while using artemis...
Hi, nice tip
When you had done a hard reset, is the GPS working fine after several reboot ?
It will be nice if someone on XDA or HTC find a solution
Yes its working fine since then and I have done several soft resets.
Fine here. The only thing that made the GPS not work for me was turning on A-GPS.
Doesn't work for me. I have changed my ROM to bElite 0.93, have done a hard reset, loaded quickgps data and still no fix after half an hour on the window.
Try going outside in the clear. If you get the fix then its the location of your window.
try using HTC GPS Tool, it fixed for me once:
http://forum.xda-developers.com/showthread.php?t=360477
install the cab, run it, then choose "Cold Start" let it run for awhile then try using your GPS software again.
Re: GPS Not Working
tararura said:
Hi everyone
I have spent a lots of hours searching for the answer to bad gps reception on diamond, through different forums.I was about to sell the diamond when I finally came with a solution and that is Hard Reset after each Rom flashing.
For a few days I could not get a gps fix, no matter what I did. I tried Quick gps, Gps tool , Google map, iGo8 and Garmin. Somewhere I read that it could be the Rom I am using. So today I flashed 4 different roms including Dutty's, bepe and panosha but no gps fix. Finally I did a Hard reset and viola, it found the satellites within 10 seconds inside near the window on all the different Gps softwares without any problem.
So here is the procedure:
***After a ROM flash finish the usual soft reset and stuff and then do a HARD RESET. Download the data through Quick Gps and your gps should work properly at its default settings.***
Actually I found that Diamond is faster than TYTNII for getting the Gps fix.
Now if the Cooks can find out what causes this behaviour so we do not have to do a hard reset after every new flash.
Please share the findings.
Cheers!!!
Click to expand...
Click to collapse
HI, ... Hard Reset,- you mean reformatting the internal storage as well? - i've done hard reset but still the gps can't fix location- says in HTC GPS tool - Mode 2: Not Fix
thanks
Mode 2: Not fix...
And the sattelites numbers show just #? Or u can see actual sattelite numbers?
Reason I'm asking is, if you just see #... then ur GPS is scr###d up and the cold start could really help.
If you do see the actual numbers, but no reception bars, then you have to get ourside into the clear sky. Be aware that nowadays windows are protective for keeping the heat of the sun outside. At the same time it keeps GPS for 95% out too.
akito said:
Mode 2: Not fix...
And the sattelites numbers show just #? Or u can see actual sattelite numbers?
Reason I'm asking is, if you just see #... then ur GPS is scr###d up and the cold start could really help.
If you do see the actual numbers, but no reception bars, then you have to get ourside into the clear sky. Be aware that nowadays windows are protective for keeping the heat of the sun outside. At the same time it keeps GPS for 95% out too.
Click to expand...
Click to collapse
Thanks akito- there's numbers-- as if it's a poor signal... same location in my window with the BT Gps receiver gives me 3D in Mode 2 almost instantly. - i'll keep trying. again thanks
You haven't been playing around with the GPS settings in the configuration of 'external GPS'? The standard settings are: GPS program port COM4 / Hardware port = none with a baud of 4800. Access tab should have GPS set to be managed automatically. Also, you have not enabled AGPS in any way like with a registry key or the advanced config program?
akito said:
You haven't been playing around with the GPS settings in the configuration of 'external GPS'? The standard settings are: GPS program port COM4 / Hardware port = none with a baud of 4800. Access tab should have GPS set to be managed automatically. Also, you have not enabled AGPS in any way like with a registry key or the advanced config program?
Click to expand...
Click to collapse
all is in default (Diamond Project Rom) as i just did a hard reset - a gps is disabled via advance config.
akito said:
Mode 2: Not fix...
And the sattelites numbers show just #? Or u can see actual sattelite numbers?
Reason I'm asking is, if you just see #... then ur GPS is scr###d up and the cold start could really help.
If you do see the actual numbers, but no reception bars, then you have to get ourside into the clear sky. Be aware that nowadays windows are protective for keeping the heat of the sun outside. At the same time it keeps GPS for 95% out too.
Click to expand...
Click to collapse
hi, nice tip
i have the same problem -> mode 2 : fix not vailble
I can see the satelite numbers, and there is some red in the reception bars (not for all, just 3), but wherever i run my navigation software (tomtom 6), why i cant get the signal GPS???? 20mins waiting, i think it is enough.
I had disabled AGPS
coca8888 said:
hi, nice tip
i have the same problem -> mode 2 : fix not vailble
I can see the satelite numbers, and there is some red in the reception bars (not for all, just 3), but wherever i run my navigation software (tomtom 6), why i cant get the signal GPS???? 20mins waiting, i think it is enough.
I had disabled AGPS
Click to expand...
Click to collapse
same probleme
solution for fix not vaible
the gps is broken ?
My problem is not the fix, but rather the lag and lack of precision while navigating...
I have more or less 5 seconds of lag, and the precision is awful...
If I use a BT external receiver connected to Diamond, than I don't have this problem...
It seems that the receiver is refreshing to less, or the communication between the receiver and the GPS software is too slow...
HastaSSSS
derkie said:
all is in default (Diamond Project Rom) as i just did a hard reset - a gps is disabled via advance config.
Click to expand...
Click to collapse
I've fixed my gps problem. I just tried to force change the gps port from settings>external gps from port 4 to port 6 and in my tomtom, i choose other receiver then tap port 6,was showing poor signal- i minimized tomtom, opened htc gps tool opened port 4 at 4800 cold start> gives me error message that the port is closed and it will force open nmea but still fail, in this part i tapped nav init.. then closed it- opened port 6 in cold start> showing all sat in #### instead of numbers. then closed it. then go to settings>external gps> then choose port 4, opened tomtom then went to gps configure and now change it to built in gps... i get full 3d 6 green bars indoor. all ok even after a hard reset. Thanks
Yeah...but how to solve the lag and accuracy issues...?...
HastaSSSS
s1rl4ncel0t said:
Yeah...but how to solve the lag and accuracy issues...?...
HastaSSSS
Click to expand...
Click to collapse
So far i dont have accuracy issue. i tried igo8 using bt receiver (SiRF III) compared it to the internal gps- it's just the same , internal gps loads even faster- In TomTom7- if i use bt receiver, some voice instructions is not complete unlike the internal gps which is flawless- maybe it's the rom/radio...
I don't have any problem
"Bonjour" (since I am french !!! )
I tried the GPS with TomTOM V7 = no problem
with garmin XT no pb
First idea
Within the programm window I have a "fast GPS" programme
Do you have this ?
Did you run it ?
Second idea
You should enable Agps in advanced config
On my diamond if I disable it doesn't work anymore
Third idea
Try to see if "GPS utilities" works
Google it it's a basic cab file for showing basic GPS (position, speed, elevation.... )
Let me know
Diamond FrencH Rom 1.37.406.1 FRE

[HELP] Garmin software doesn't detect GPS receiver?

FIRST POST!
Hello xda-developers!
I have got a problem with the Garmin software for my Omnia 2
I've installed everything correctly, the software, maps, etc. (as far as I know)
But as soon as I want to connect to a GPS device it keeps scanning for a receiver.
I thought Omnia2 has a GPS receiver installed in their system?
If so, is there anyone that could help me out?
Greetings
VleNiK said:
FIRST POST!
Hello xda-developers!
I have got a problem with the Garmin software for my Omnia 2
I've installed everything correctly, the software, maps, etc. (as far as I know)
But as soon as I want to connect to a GPS device it keeps scanning for a receiver.
I thought Omnia2 has a GPS receiver installed in their system?
If so, is there anyone that could help me out?
Greetings
Click to expand...
Click to collapse
did you use the correct com in gps settings??
I use com 6 on my i920 but yours maybe different.
kdkinc said:
did you use the correct com in gps settings??
I use com 6 on my i920 but yours maybe different.
Click to expand...
Click to collapse
Well, where can you find information for this?
I've seen
GPS-Programport: COM7
GPS-Hardwareport: COM9
Baudrate: 4800 (default)
But I haven't seen any option yet where I can choose which GPS (internal or external) device I want to use, when I click on the icon in the upper left corner of Garmin
Click the gps signal bars on top left side and then disable then select your port
Rhodium500 said:
Click the gps signal bars on top left side and then disable then select your port
Click to expand...
Click to collapse
Thats what I've tried.. It says: Only connection with Garmin GPS-device allowed
any ideas?
*EDIT*
I've reinstalled everything.. Now it suddenly freezes if I want to press on the signalbars..
GPS
HI
You need two app
GPS Gate and BeeLineGP to make it work
i had similar problem that you are encountering
after installing the two app and configuring it i finally fix it.
hope that helps
joee1 said:
HI
You need two app
GPS Gate and BeeLineGP to make it work
i had similar problem that you are encountering
after installing the two app and configuring it i finally fix it.
hope that helps
Click to expand...
Click to collapse
Have installed it. Now I can select what port etc. GPSgate says a GPS receiver has found on port 7 and ready for use..
So I open up Garmin, go to signal and it uses port 7 as GPSgate adviced.. Now waiting for a satalite signal.. But it takes ages! I'm standing outside, clear sky and everything.. I'm I still doing something wrong?
GPS
Hi VleNiK
Fellow these instruction!!!!!!!!!!!
I am assuming that you installed GPS Gate 2.6
In your phone go to Start and find GSP Gate
Click on the app and hit settings.
next in the input select setting
next step is to configure port
serial port is com7
Baud Rate is 57600
press OK once your done
Now back to Input menu
click Open
It will tell you that the GPS is OK but no position.
This is fine so leave the application.
Next is is Beeline GPS app
I am assuming that you installed the BEELINEGPS app version 1.90 or 2.0( 2.0 is a beta but it works really well) the trial version is 30 days for both version.
open the app than go out side get a clear view of the sky
wait for few minutes and it should be OK. the way to tell if it is working
is when the latitude and longitude has numbers.
close the app by passing the x button at the top once it is working
open Garmin and everything should be fine.
note: if you completely turn off the phone then you have to do the steps again. so i suggest you put the phone on stand by.
Hope that helps
JOE
since i made these changes,gps works fine for my tt7.
it's the same issue with the gps sensor, so maybe it will work for the garmin software too.
at first: you DO NOT have to install any other software except an regedit if it isn't already installed.
-open the regedit and got to:
HKEY_LOCAL_MACHINE\System\CurrentControlSet\GPS Intermediate Driver\Drivers\Samsung GPS Hardware\InputBufferSize:
change value from 4096 to 512
-then go to:
HKEY_LOCAL_MACHINE\System\CurrentControlSet\GPS Intermediate Driver\Drivers\Samsung GPS Hardware\OutputBufferSize:
also change the value from 4096 to 512
-next step is:
HKEY_LOCAL_MACHINE\System\CurrentControlSet\GPS Intermediate Driver\Drivers\Samsung GPS Hardware\SleepOnNoData:
change value from 100 to 0
-last step
HKEY_LOCAL_MACHINE\System\CurrentControlSet\GPS Intermediate Driver\Multiplexer\MaxBufferSize:
change value from 16384 to 1024
now save these settings and close the regedit.
got to yor gps settings and set:
programport: 4
hardwareport: 9
baud 4800
softreset your device.
that's it,i hope it'll help you...
joee1 said:
Hi VleNiK
Fellow these instruction!!!!!!!!!!!
I am assuming that you installed GPS Gate 2.6
In your phone go to Start and find GSP Gate
Click on the app and hit settings.
next in the input select setting
next step is to configure port
serial port is com7
Baud Rate is 57600
press OK once your done
Now back to Input menu
click Open
It will tell you that the GPS is OK but no position.
This is fine so leave the application.
Next is is Beeline GPS app
I am assuming that you installed the BEELINEGPS app version 1.90 or 2.0( 2.0 is a beta but it works really well) the trial version is 30 days for both version.
open the app than go out side get a clear view of the sky
wait for few minutes and it should be OK. the way to tell if it is working
is when the latitude and longitude has numbers.
close the app by passing the x button at the top once it is working
open Garmin and everything should be fine.
note: if you completely turn off the phone then you have to do the steps again. so i suggest you put the phone on stand by.
Hope that helps
JOE
Click to expand...
Click to collapse
thanks JOE ! It finaly works! BUT.. If I've got a signal and close Garmin, and put it back on lateron.. Do I have to search for a new signal again in an open sky? Because it realy takes a while..
I never had to use BEELINEGPS or GPS gate to get Garmin work on my Omnia i8000...
Just installed the software along with Voice support file and Base Map.. and then I copied India map.. Thats it.. Went to an open place and launched Garmin.. Waited for about 2mins and got a GPS signal...
Below are my GPS settings..
GPS-Programport: COM7
GPS-Hardwareport: COM9
Baudrate: 9600
Hope this helps...
Aafi-rocks said:
I never had to use BEELINEGPS or GPS gate to get Garmin work on my Omnia i8000...
Just installed the software along with Voice support file and Base Map.. and then I copied India map.. Thats it.. Went to an open place and launched Garmin.. Waited for about 2mins and got a GPS signal...
Below are my GPS settings..
GPS-Programport: COM7
GPS-Hardwareport: COM9
Baudrate: 9600
Hope this helps...
Click to expand...
Click to collapse
Hi,
thanks for your reply! Well I tried it that way from the beginning.. But for some reason my Garmin Software only detected Garmin Bluetooth devices.. So not my internal one. And BeeLineGPS & GPSGate helped me with it. Now I have to boot those programs before using Garmin Mobile, shame but it works!
Gps
thanks JOE ! It finaly works! BUT.. If I've got a signal and close Garmin, and put it back on lateron.. Do I have to search for a new signal again in an open sky? Because it realy takes a while..
Yes you do have to re-open gps gate and Beeline GPS in a open sky place. I am trying to find a better solution to this problem. Using the GPS in Omnia ii is very tedious. I live in Canada and Garmin mobile xt just does not work once i open it. maybe in India but not in Canada i think. Aafi-rocks.
Also I tried lewellyen method everything works out great at the first time but when i open the garmin xt second time it freezes. It would not work at all. entail i had to go back to the old configuration.
My method is all i know so far but if any body have a better solution please share
Joe
There is another bunch of settings in nogarderGPS.exe accessible by typing *#1472365# on your dialer. On the menu select Settings | GPS
For Operation Mode select STANDALONE
For Start Mode select HOT START
For Session Type select NAVIGATION
See if this helps you. I use the GPS with google maps and it works just fine in Canada. I went to the Cook Islands, changed my SIM card and the GPS got a lock in 2 minutes - of course google maps didn't work because I didn't have any internet access.
try this
I) Go to General Settings - GPS
1) GPS program port : COM 7
2) GPS hardware port : COM 9
3) Baud Rate : 9600
4) Enable Manage GPS automatically
5) Make sure to download the XTRA data every week or so while connecting to internet trough Active Sync
II) Under Garmin XT - Click signal bar ( top left icon )
1) MAKE SURE its COM7 : COM7
2) IF NOT then click disable button
3) Click Use serial GPS - set it to COM 7
4) Then Enable it back.

Categories

Resources