Related
Maybe some of you are already aware of this procedure, maybe not.
Anyway, it worked for me and I decided to share how to do it. Simple.
This procedure should only be used in case you really need enter into a bootloader mode and all other ways to do it has failed! Hold Camera button is one of these I am mentioning.
My Wizard was almost bricked at that time and after I speak with an I-mate technical guy, I got the following:
1. Make sure your i-mate™ K-JAM is not Connected to the PC and remove the dummy card or SD/MMC card
2. On your Desktop PC, open Microsoft ActiveSync, then go to File >Connection Settings >Remove the Selection from “Allow USB Connection with this desktop computer”
3. Reconnect your i-mate K-JAM to the Desktop PC using the USB Cradle and the Charger MUST be Connected to the Cradle (Don’t use the IrDA or Bluetooth for the Upgrade)
4. Run the Upgrade again and it will work fine without any problems.
While upgrading, the ActiveSync program will not go on, however the upgrade is running.
Hope it helps!
this realy worked for my (ex)bricked dutch tmobile mda vario !!!!
tip: REALY make shure that there is no wcescomm.exe running all the time and realy remove the sd card else is nogo
btw: my wizard is CID locked! and works like a charm
Thanks buddy!
I'm happy that worked for ya!
Take care!
I'm having a problem
The power went out as I was upgrading my Wizard (Cingular) so now it just turns on at the boatloader screen. I've tried running updates while it was in this screen (it did show the "USB" in the white bar) but most of the time it tells me there is a connection error. Even if I kill Activesync, I notice that when I run the update utility it still runs Activesync. I've tried disabling the USB connection but still get the connection error.
The only time I haven't gotten the connection error was twice it asked me to update but then told me I had the wrong file. This only happened when I tried "upgrading" to 1.05 as I was trying to start again. After it tells me that if I try running it again it gives me the connection error.
Any ideas?
Hi!
Have you already flashed your device once?
Which ipl/spl do you have?
I had problems over 1.05 ROM in the beggining.
If you stuck on bootloader mode, that's a good signal your device is not bricked.
I'd recommend you to disable activesync as you did and reflash it again! Check also if your device is CID unlocked! Search for a thread in the xda developers root.
Try to upgrade to ipl/spl 2.26 first and later to others you want.
Regarding the old file error...can be related to a missing file called enterbootloader.exe.
Hope it works for ya!
Take care
Ironman273 said:
I'm having a problem
The power went out as I was upgrading my Wizard (Cingular) so now it just turns on at the boatloader screen. I've tried running updates while it was in this screen (it did show the "USB" in the white bar) but most of the time it tells me there is a connection error. Even if I kill Activesync, I notice that when I run the update utility it still runs Activesync. I've tried disabling the USB connection but still get the connection error.
The only time I haven't gotten the connection error was twice it asked me to update but then told me I had the wrong file. This only happened when I tried "upgrading" to 1.05 as I was trying to start again. After it tells me that if I try running it again it gives me the connection error.
Any ideas?
Click to expand...
Click to collapse
My device is unlocked as I've been trying different ROMs as of late. I had gone back to the Cingular 2.25 ROM for a couple days to sort some things out and was going to flash Farias AKu 3.3 when my power problems happened. My Current IPL/SPL is 2.25
I've tried flashing the TMobile 2.26 but keep getting connection errors. In fact, I've tried flashing with every ROM I have pdviet 3 and 4, CIngular 2.25, TMobile 2.26 and Custom 1.05. Everything (except twice in the custom) gives me connection errors.
Any other trick I can try?
BTW, I used to live in Sao Paulo years ago...
Edit: OK, so I tried the 2.26 TMobile ROM after I typed this and it worked!! I'm back up but I was having trouble with that ROM beause of some incompatibilities with Cingular. I'll go back to Cingular's ROM and play it safe for now.
I believe part of my problem was I kept trying different updates one after the other. Now that I think back, the 2 times I got the update to almost work was after I turned off the device and turned it on again, which is what I did this time around also.
I had the same problems as mentioned by Ironman before. I followed the steps and with a few slight changes, I managed as well to "unbrick" my wiz. THANKS A LOT for the great step by step manual!!!
Still I wanted to know WHY i bricked my device:
I was trying to upgrade to the underground WM6 ROM. I got the same situation as ironman:
Quote:
The power went out as I was upgrading my Wizard (Cingular) so now it just turns on at the boatloader screen. I've tried running updates while it was in this screen (it did show the "USB" in the white bar) but most of the time it tells me there is a connection error. Even if I kill Activesync, I notice that when I run the update utility it still runs Activesync. I've tried disabling the USB connection but still get the connection error.
The only time I haven't gotten the connection error was twice it asked me to update but then told me I had the wrong file. This only happened when I tried "upgrading" to 1.05 as I was trying to start again. After it tells me that if I try running it again it gives me the connection error.
Unquote
I then followed the instructions by epimazzo as written above. I also tried the T-Mobile ROM 2.26 which was not working for me. PANIC!!!! Error messag was that I had the wrong Vendor ID. THerefore no upgrade to TMob 2.26 was possible. I tried it then my original qtek ROM in my language and see it worked!!! This IMHO means that I did not put the device in a proper IPL1.xx and SPL 1.xx status which is required for a clean system in irder to unlock it! So if it is bricked, try your native AKU2 ROM and make sure you unlocked it properly. Maybe you have to run the 1.05 ROM for a second time after the unlocking.
I hope this helps you guys.
Sounds great to hear that!
I had play around with pdaviet3, underground and another ROM just today without any problems at all. I don't think that this is the case. Now you get your device back to normal, try to reflash it again. Hope it works this time!
BTW,...São Paulo is a nice city. Thanks! Let me know if you decide to come here!
Take care
Ironman273 said:
My device is unlocked as I've been trying different ROMs as of late. I had gone back to the Cingular 2.25 ROM for a couple days to sort some things out and was going to flash Farias AKu 3.3 when my power problems happened. My Current IPL/SPL is 2.25
I've tried flashing the TMobile 2.26 but keep getting connection errors. In fact, I've tried flashing with every ROM I have pdviet 3 and 4, CIngular 2.25, TMobile 2.26 and Custom 1.05. Everything (except twice in the custom) gives me connection errors.
Any other trick I can try?
BTW, I used to live in Sao Paulo years ago...
Edit: OK, so I tried the 2.26 TMobile ROM after I typed this and it worked!! I'm back up but I was having trouble with that ROM beause of some incompatibilities with Cingular. I'll go back to Cingular's ROM and play it safe for now.
I believe part of my problem was I kept trying different updates one after the other. Now that I think back, the 2 times I got the update to almost work was after I turned off the device and turned it on again, which is what I did this time around also.
Click to expand...
Click to collapse
It seems you got the idea!
You did the right thing! Sometimes, use the official ROM can solve many issues out there!
Keep walking!
enlite_de said:
I had the same problems as mentioned by Ironman before. I followed the steps and with a few slight changes, I managed as well to "unbrick" my wiz. THANKS A LOT for the great step by step manual!!!
Still I wanted to know WHY i bricked my device:
I was trying to upgrade to the underground WM6 ROM. I got the same situation as ironman:
Quote:
The power went out as I was upgrading my Wizard (Cingular) so now it just turns on at the boatloader screen. I've tried running updates while it was in this screen (it did show the "USB" in the white bar) but most of the time it tells me there is a connection error. Even if I kill Activesync, I notice that when I run the update utility it still runs Activesync. I've tried disabling the USB connection but still get the connection error.
The only time I haven't gotten the connection error was twice it asked me to update but then told me I had the wrong file. This only happened when I tried "upgrading" to 1.05 as I was trying to start again. After it tells me that if I try running it again it gives me the connection error.
Unquote
I then followed the instructions by epimazzo as written above. I also tried the T-Mobile ROM 2.26 which was not working for me. PANIC!!!! Error messag was that I had the wrong Vendor ID. THerefore no upgrade to TMob 2.26 was possible. I tried it then my original qtek ROM in my language and see it worked!!! This IMHO means that I did not put the device in a proper IPL1.xx and SPL 1.xx status which is required for a clean system in irder to unlock it! So if it is bricked, try your native AKU2 ROM and make sure you unlocked it properly. Maybe you have to run the 1.05 ROM for a second time after the unlocking.
I hope this helps you guys.
Click to expand...
Click to collapse
Excellent post. I messed up with my own cooked ROM and could only get the bootloader screen. Tried the tips here - didn't work first time but I pulled the battery from the KJAM to reset it rather than using the reset button and it worked fine.
In my opinion this thread is so helpful to people who brick their device, it should go "sticky". Mods anything you can do about it?
Thanks buddy! I really appreciate!
We survive here over tips like that!
jt_armstrong said:
Excellent post. I messed up with my own cooked ROM and could only get the bootloader screen. Tried the tips here - didn't work first time but I pulled the battery from the KJAM to reset it rather than using the reset button and it worked fine.
Click to expand...
Click to collapse
Help me similar problem
I upgraded Super Rom, then my Wizard run very slow and no signal (no call out and in- no network at all). And Terible thing is PC could not dectect PPC thought Active Sync. I've soft and hard reset but no use.
So I donot know where to start to re install Rom again.
Please help me....
Hi there!
It seems that you just need to enter into the bootloader mode and reflash it again!
I had similar problems and more during my brick "false" stage!
So, just try to follow my steps here and you should be fine! Once you get into bootloader mode, just use any ROM out there to reflash.
Good [email protected]
thaiphong said:
I upgraded Super Rom, then my Wizard run very slow and no signal (no call out and in- no network at all). And Terible thing is PC could not dectect PPC thought Active Sync. I've soft and hard reset but no use.
So I donot know where to start to re install Rom again.
Please help me....
Click to expand...
Click to collapse
I was about to start a EMERGENCY HELP thread, but I *think* this is the right place instead.
The "touch" of my screen went dead today. It got progressively worse over a few hours, starting with difficulty in using the phone dialer, then random incorrect stuff getting triggered by screen taps.
So I hard reset, and got no response on the fifth alignment cross, meaning 1) "Tap on the screen...; 2) center; 3) top left; 4) bottom left; 5) bottom right. In that I could not proceed with alignment, I hard reset again, and now, at the first alignment screen, i.e. "Tap on the screen...", I have no screen response at all.
I called T-mo, and they are being great about sending a replacement ASAP (and getting me a loaner in the meantime).
BUT, I am running Faria+ AKU3.3 V2... so I clearly have to flash back to T-mo 2.26. I can;t figure out how to do it though, as no matter what I do I am stuck at the first alignment screen!!
HELP!! EMERGENCY!!!
(I have three or four days to get this done, so it's not THAT urgent)
Do a search for Broken Screen. Someone (either in Wizard Upgrading or in the Wizard forum) just had a similar issue with a cracked screen. They downloaded something that allowed them to get around the welcome page.
Actually, if you are just trying to flash a new ROM, don't even mess with it. Go straight to the Boot Loader screen (see the first post of this thread). No tapping necessary until the new rom is on (and that will be the Tmobile then so you would be good.
Thanks for the quick reply. Charging up to green now, and then will try to enter bootloader and flash T-mo 2.26. Will report back.
Worked great. Back to T-mo she goes!!!
BootLoader Mode
Excellent thread but you left out one thing.....exactly how to place your device in bootloader mode.
To clear up any misunderstanding because this is very important....this is how you do it:
Perform a soft reset, when the screen goes blank hold the camera button until a multi colored screen comes up .... That's it !!!!!!
When the unit is connected, USB is displayed at the bottom left.
There is a problem with my MDA: It continually flashes the volume/ringer control on the screen with the circle with the loudspeaker and mic turned off. This flashes every second or two and when it flashes, prevents pretty much anything else from working or command from executing.
I had a very old TMobile software version on it. I down loaded a much newer version from TMobile in an attempt to get rid of this problem before upgrading to XDA firmware: (The whole thing is very out of warranty)
The upgrade went successfully but the flashing volume / ringer control still flashes.
Does anyone know what this means or if upgrading to XDA will get rid of this problem (or exacerbate it!)
Has anyone noticed IF there is a problem with Puttenham's "Step 17"?
I got around my nerves about upgrading this G3 with a hardware problem in place and appear to be encountering a severe problem with Step 17 which is that it says it is "Your Choice" to go to a 3.08 SPL/IPL. Nowhere however does it say which later ROMs you can apply if you DO choose to go with the 3.08. I applied this to correct what I thought was the hardware issue (reinstalling the T-Mobile ROM at SPL 2.26 didn’t seem to cure it) and the 3.08 did install properly and cured the hardware problem.
I tried different ROMs because I cant seem to understand how to use VoIP or which ROM will let me use this 'feature' or which ROM has this feature built it as some say they have deliberately taken it out.
Suddenly I am getting error messages telling me that the unit needs a later ROM revision to install perfectly.
(WizardLove was the first to do this: It executes in Italian and as I mentioned, just tells me that it needs a later version to work)
So I reflashed with the Molski ROM which is the only one which seems to be around and the flash worked up until 94%. At that stage the progress bar turned to red and there was an error message telling me that I can recover and try again. I did this a few times and SEEM to have bricked my Wizard (When the Molski upgrade failed, attempts to chkdsk, reboot, delete all temp files etc failed). The unit will now only boot to the three-colour screen? Further attempts to flash seem to see and read the device and tell me either that there is no ROM on it and would I like to upgrade? Followed by this unexplained 'USE LATER ROM'. (There may be a problem with installing the T-Mobile ROM on an unlocked Wizard with a 3.08 IPL/SPL However it has to be said that Molski is, still, the only ROM which runs and it inevitably stops at the same position, the 94% mark when the MDA progress bar goes red, the unit shuts down, the upgrade process thinks about it for a while and ultimately reports ERROR [302] UPDATE ERROR)
Alternatively they (for example ROM Update Utility 2.00.1) tell me that there is no communication between the PC and the Wizard. Actually ActiveSync 4.5 does show no connection between the device and the PC, which I suppose I would expect if the Molski ROM failed to complete? Device Manager seems OK with the unit being in place though? And I cant believe this is important as there obviously IS connection between the computer and the PDA
Easymob said he would let users have a path to a ROM they could use but no where is it set out which ROMs you can use of the ones you actually CAN find?
I have also tried the Xelencin ROM which initially tells me that it cant see the PDA. Then it admits that it can and tries to unlock the CID (which surely must be already unlocked by now if I have upgraded to the later SPL??)
I am not sure I have a totally bricked unit, - The Xelencin T-Mobile ROM MUST be doing something because it does successfully run the RAPI unlock and after a few error messages telling me it can't access the MDA, reports DONE! But then it tries to run Machinagod's HTC Wizard Unlocker and gets stuck. It shouldnt get stuck at this step as I must already BE unlocked! It should pass this step.
I can hear hdd movement (not churning) but the program doesn’t progress past this step. Ultimately this carries on for hours and the Wizard shuts down I presume when the battery fails as the charge function doesn’t seem to work in ROM upgrade three colour screen mode. Plugging the charger in now doesnt seem to do anything
Again as the program was built for the 2.26 SPL, I still cant figure out whether these available ROMs should run on the 3.08 which I followed in the STEP 17.
MEANWHILE BACK AT THE RANCH: Is there a more obvious answer to why Molski always fails at precisely the same 94% position?
Hey there everyone, I am pretty new to this forum so I must apologize for throwing you all into the deep end. I recently purchased an o2 XDA mini S second hand from a guy on boards.ie here in Ireland. I got the phone and really liked it because it allowed me to get rid of my Dell Axim X3i and mp3 player and keep it all in one device.
After a little bit of more research I discovered that I could remove some of the bloatware from the o2 xda mini S by just hard resetting and choosing the basic option which I than did. Still not satisfied with the overall performance of the XDA I decided to try a rom upgrade. Not wanting to do a totall overhaul I decided to just do a radio upgrade first.
My device is sim unlocked, it was like that when I bought it. I used the latest wizard service tool to CID unlock the device before I even flashed the phone. I also used the wizard service tool to change the nk.nbf file within the o2 mini S radio update into 96000000-GSM.nb. I then used this file to write to the GSM radio code (Bdk 1) according to the wizard service tool in the hopes that it would upgrade my radio version.
Well when I restarted, nothing of the sort happened, on the boot screen I noticed I was now missing my GSM version and when the phone finally got into windows mobile, it did not pick up any signal even though beforehand it could. The phone also became super slow to the point where it was unusable.
I have gone into bootloader mode subsequently after reading on this forum and tried to reflash with a number of updates with active sync disabled and nothing else running with the phone connected via usb to the pc. None of the updates would even pick up the phone or allow me to flash it.
My phone is pretty much screwed, I have a spare so it is not that big of an issue but I would like to make this usable again if at all possible. So my question is how do I flash a rom while the phone is in bootloader mode?
P.S I forgot to include the Current boot screen details:
IPL - 1.05
SPL - 1.05
OS - 1.5.4.2
Hi,
You can use the Wizard Love Rom from here http://rapidshare.com/files/17792050/Wizard_Love_2.26.10.2_WWE_Novii_CF2.rar
Hey there, thanks for the advice, I did download that ROM but like I said before, none of the roms manage to flash my XDA because they all cannot seem to connect to it. Activesync does not even pick it up in windows mode, and even when I have it connected in bootloader mode via usb and I double click on the love rom, it goes through the motions but never managed to "verify the information with the pda"
Try a stock Tmobile ROM but not from bootloader. Also, I would check the activesync app on the device. Make sure it's set to use USB as the default connection method.
A few other steps to try...
Uninstall ActiveSync and install an older version. If still no go, try a newer version.
Try a different USB cable and/or USB port.
Try a different computer with XP, not Vista.
Try flashing it without the SIM card or any memory cards.
If all else fails, you can try the SD card flashing method. There are instructions in the Wiki on how to do it, but always a stock ROM.
Try this one... http://forum.xda-developers.com/showthread.php?t=311027
Updated IPL/SPL and radio 2.69
Hey Devis, I think I have come one step closer, I tried all the suggestions that you made. Except well now my phone will not even go into the operating system when I switch it on. It will boot and the version numbers show but then it just resets itself.
I tried a different usb cable and I am not using vista, tried a different pc and the same result. The one place I did have some marginal success was the sd card method.
Basically what happened is that It backed up the OS from my phone and then reloaded it, not exactly what I wanted since the OS and rom are both screwed on the phone so my question at this point is, is there anyway using the SD card method to load one of the stock roms onto my phone?
I searched around the net and found the opposite to the "r2sd all" function, would be the "s2d" function, would that allow me to flash the phone with a stock rom?
Thanks for your time, I am going to call it a night here in ireland and head to bed.
Ok, if the phone resets then you probbably have a dead/dying battery. Charge it for about an hour or so using the wall charger, not the USB cable. Try to restart it and see if you can get in the OS. I was looking in the SD card method thread and some guy was successful at restoring the image from the SD even though his OS had died. He then had a fully functional phone.
The other thing to do would be to get the image file from someone that has a living and breathing wizard, preferably one with a stock ROM. Since this method is the equivalent of making an image of a PC using Ghost, the restoration of such an image to your Wizard should work just fine.
Just make sure that the other Wizard is SIM and CID unlocked. Or just go buy a Wizard from the store, unlock SIM and CID, copy the image on the SD and flash your device. Or... since u've got a new Wizard in your hands, just take the freaking thing appart and swap the guts return the store bought wizard to the store saying that the thing just doesnt freaking work!
As for the AT commands... it is possible that s2d would workfor you, it doesn't work in my wizard. from what i have been reading it appears that the bootloader is password protected and that password is randomly generated. I haven't played long enough with it to figure out how to get the password.
It looks like you've got some "trial and error" processes ahead of you. There is a wealth of info on bootloader AT commands on Wiki, nothing for the Wizard though. But something may work... not sure.
I could try to get you a ROM dump from my Wizard but I already am on SPL/IPL 3.08 and running WM6. the SPL/IPL version alone wouldn't allow you to restore from my backup.
Hey Devis, thanks for your time, just woke up here, will work some more on the phone today and let you know what is going on
Hey Devis, I did not even get a chance to fiddle around with the phone today, from being able to switch on less than 24 hours ago, it does not even want to switch on now so I am going to officially declared it a brick and move on. Will see if anyone can fix it for me, spent way too much time already when I should be working on my dissertation, thanks alot anyway
Sorry to hear that...
I have bricked one phone myself in the past... my old Pana GD87 and I absolutely loved that phone. I know how you feel.
Good luck with your dissertation.
Hi all,
I have been visiting these forums for 2 years now and have downloaded some great tools and ROMs to enhance my Trinity, however something all of a sudden has gone very wrong!
I upgraded to WM6.1 Elegance edition about 3/4 months ago, CID unlocked the phone about a month ago and everything has been working like a dream.
However just today, I attempted to turn the volume down on my phone during a meeting (I always forget to normally!) and there was no display. After few battery resets, again no display. It starts up, loads the the Elegance splash screens and then hangs on the screen before when the OS should appear.
My decision was to flash the ROM again. I cant flash using Activesync as it wont pick up on the hung screen, so I started the bootloader and got as far as 1% of the flash and it will restart. So I tried the SD Card method when resulted in a "loading" screen appearing for a few seconds and then it goes back to the standard bootloader and displayed a 00068002 error.
I am out of ideas, I hear mtty.exe is a good program for this kind of thing, but what I want to know is if this is fixable or if I should give up!
I have been working on this since 2pm today none stop!
Can any of you guys give me any suggestions please?!?!?
Kind regards,
Jonathan
Should be a cinch
Did you SPL the Phone before flashing roms?
If you put the phone into the bootloader mode The RGB screen and kill of activesync you should be able to run one of the flash update programs.
If I have flashing problems its usually Active sync so I kill it then run the flash program.
I've got a sneaky suspision your battery might be causing the problem.
Hi there, thanks for the reply. As I was new to upgrading I havent used SPL on the phone before flashing the ROMS. I did use an unlock tool recently as i wanted to try a different network SIM to see if it worked when I was in South America, so the phone is unlocked to all networks. Are you saying if I SPL now it should sort the problem out? If so how do I do this withour ActiveSync working - can you use SD?
Another thing I failed to mention was that when I start an upgrade and it follows all the steps, it doesnt say the current ROM on the screen where you press update ROM. It just gives the name of the new ROM and the current one is left blank.
I have disabled Active Sync before attempting the update. It seems to go through fine and then the phone restarts wafter 1% of the update.
What makes you think it is the battery? I am happy to spend under 20 pound on ebay if you think it will fix the issue!
try unbrick.bat.......my trinity was also stuck.......unbrick.bat save my day....
The same happened to me several time....I could not find a solution other than this one:
1. Flash the official HTC ROM.
2. Flash the required ROM then.
it works for my TrinTy.
i have searched for a long time and cant find any answers i have a tmobile mda ive tried running the tmobile rom and it didnt work gave me an error any advice please help me i wan wm5 again
Download Official T_mobile wm5 Rom from this link,bet the phone in Bootloaders (RGB screen) and flash to recover back to its default status,then read carefully this guide fron the below mentioned link and do the unlocking and upgrading.
T_Mobile Rom:-
http://rapidshare.com/files/38880130/ruu_prodigy_226102_22610105_022511_tmous_wwe_ship.exe.html
Unlocking Guide :-
http://wiki.xda-developers.com/index.php?pagename=Wizard Windows Mobile 6 for newbies
thats the prob when i do iit it takes me to the rgb screen and the comp says error any info for that
Exactly what error it displays,it must with an error No. and some explanation about it,can you recall it correctly.Does it display Communication error ?
pmed error 260 communication
Ok,I hope you are doing all this on a WinXP machine,if its a vista,it won't work,WinXP is recommended.Now,before start to flash,close/disable any Anti virus and firewall running on the pc,and also try to close as many applications running on the desktop or background through Task manager,don't surf the net during flash or do any Office work.
Close/disable Activesync,coz its not needed while flashing,end the process 'WCESCOMM.EXE' in the Task Manager,delete any Partnership with Activesync.
To check the connectivity problem,get the phone into Bootloaders (RGB) and hook up the phone with pc via usb cable and watch small usb appear at the bottom of the Bootloader screen,if its there,its establishing connectivity,than its good to go and run the flash,but if its not there,then its a connection problem.It may be the usb cable or mini usb port of the phone is faulty,check this out and do the needful.
Many communications errors are also due to dead or discharged battery,it doesn't have enough juice to complete the flash,hence,results in comm error,always start to flash with a fully charged battery.
le problem was the laptop i used a different one and its almost done i got another ? if i changed the radio am i gonna have to get the original tmobile radio too or does it change with the downgrade
Original ROMS
lorijuan1024 said:
le problem was the laptop i used a different one and its almost done i got another ? if i changed the radio am i gonna have to get the original tmobile radio too or does it change with the downgrade
Click to expand...
Click to collapse
The Original ROMS got his Radio ROM included. in fact... Stck ROMS got...
IPL and SPL
Extended ROM
Operative System
Radio Version
Can this be done if I have Vista?
I know someone mentioned installing a rom won't work with Vista, but I was hoping maybe it was just a personal preference. I have two pcs that both run Vista and Linux. My problem is, the wm6 rom (faria crossbow) doesn't work by default and I have a cracked screen so when I try to set it up I can do every step except setting the proxy port #s because when I highlight one there's no way to tap on it, and pressing or holding the select button (the button in the middle of the 4 way joypad) doesn't allow you to edit the values or pop up a context menu. I was hoping to get my $5.99 internet or at least my email and mms working but I got layed off and the holidays are coming so I prob won't have the extra (I know its not much, but I have no job) $30 to buy a new screen until sometime in the new year.
Why not downgrade to the Button ROM, and then upgrade to WM5 afterward?
Chuck