Problem with Kaiser on Mobile device center. - Tilt, TyTN II, MDA Vario III General

Hi Guys,
I (did) have the kaiser working fine with WMDC, thanks to an update from MS. However, to get my old Hermes ready for Ebay, I followed the instructions in this thread:
http://www.modaco.com/content/windo...u-on-vista-it-can-be-done-the-ultimate-guide/
(Which IS a great guide btw)
When I'd finished, I tried to get back to my Kaiser drivers, but just cant get it to work. I have though aboot removing the update, so I would get it again from MS, but it is not appearing in the remove updates dialogue in Vista. If someone could advise on where the update might be on my system, or link to the kaiser vista driver I would be grateful. I have tried re-installing both WMDC 6 and 6.1 with no joy.
Any help would be appreciated....
Cheers bods
Stoo1701

Related

Attempted WM5 Rom upgrade and got stuck!!!

Hey Guys i would need some help here i downloaded the Helmi upgrade rom but didnt seem to work. i get the device connection error before it even starts
i downloaded the official rom that i found on this forum on this link
ftp://ftp.clubimate.com/PDA2k_WWE_14000_176_11200.exe
as u can c this is the one from the Imate website when i attempted to install it. it actually didnt give me a connection error and started to install but when the PDA rebooted i got that connection error back and now i am stuck at the bootloader screen with SERIAL written at the top and V. 2.06 at the bottom tried to soft and hard reset but nothing seems to happen i even disconnected the battery for 30 minutes but couldnt get it to boot
Anybody pleeeeeease heeeeeeeeeeelp!!!!!!!!!!
Thanx
Please give us more information.
What windows are you running? XP or Vista?
Do you have an error number?
I run windows Vista and the error number i get is 101 Connection error when i attempt to run BaUpgradeUT
on the PDA the only screen i fet is the bootloader screen with SERIAL and V.2.06
Ok, the problem in flashing our precious BA under vista is that you need to replace the usb driver with an old version so the updater will work correctly.
Search the forums for vista update or vista flash and you will get the answer and the driver you need.
thanks a lot i ll try it right now been waiting for this
OK i just searched for vista flash and found this post
http://forum.xda-developers.com/showthread.php?t=313001&highlight=vista+flash
tried it it worked done upgrading and now i have WM5 on my PDA2k
thanx alot u really saved my day
i am looking for imaginet arabizer for it now to fully enjoy the experience
And one more thing i have to thank Duanes who posted up the vista upgrading manual linked above Thank you

WMDC will not make connection with my wizard

First if all i want to say that i am a newbie with flashing HTC devices. But i managed to downgrade my wizard with the button rom.
I have been reading several forums en tried googling my frustratung problem. I followed the manual that was posted on this forum. Everything went wel until i had to SIM-unlock my phone. The rom was installed en the wizard started up as it should.
When i wanted to SIM-unlock i took me 2 days to get the connection between the wizard and vista back up again. With luck i managed to unlock the phone (2 days ago). But now i cannot get this connection up again to CID-unlock.
I tried everything. Every program that could interfear with WMDC I shut down or uninstalled. Also tried several times to re-install WMDC and master-reset the wizard. Everthing what i found on the forums i tried. From disabling the firewall to stopping services.
Everytime i connect it finds a device: Microsoft Windows Mobile Device #3
I unistalled this device and tried again and again. Still no connection.
The strange thing is that the device gives the connection icon with a cross but is still says it is connected with active sync.
So please help me out or give me some hints so i can finish the upgrade.
BTW: I dont have an option for USB-PC on my Wizard
Hopefully somebody can help me

Upgrading to WM6.5 on XDA IIs - Error 150 Maupgrade

Hey guys,
I am trying to upgrade my XDA to WM6.5. When following the wizard steps, I enter the PDA into the bootload menu, but when I run the application on my XP desktop, I recieve the following error:
Error 150: Rom Upgrade Utility Error
This ROM upgrade utility does not design for your device.
Please get proper ROM upgrade utility and try again.
Help! It's frustrating the hell out of me!
please add which rom you currently use, do you have activesync installed
Me also have the same error
I have yust tried to install the new release with the same result.
I have a Qtek 9090 with WM 6.1 rel 5.2.20262 b. 19949.1.2.0.black, but in the past month I have tested many other...
Simply the install program don't recognize the device so cannot define if it's right or wrong.
Thank you in general for your fantastic jobs !
Sorry !
Yes I have Activesync installed (for another palmsize divice).
What????
Palm size device???? so you dont have activesync... you have hotsync but....
You already tried the WM6.1.... so you have activesync... men you are getting me crazy jejejej lol
BTW...
Try to conect your device if the activesync dont recognize it and sync.... restart your PC and PPC... the if this not works...
Uninstall the AS then Reinstall it..... if not works...
Try to change to other USB port
If dont works check your advanced conections settings
and check or uncheck the advanced network config box..... if not works...
BTW upgrading needs bootloader so put it on Bootloader mode conect it if your PC says something about not recognized just.... try other PC.... are you on VISTA or XP? suggested... XP.
Thanks
I have used very bad words, so don't panic ! The other device is a "normal" HTC 3300 (artemis) with 6.0 italian std rom and A.S. 4.5.0 (Build 5096) on Win XP.
The 9090 syncs regularly and it is regularly connected (I have stopped the bootloader and reboot the BA), I will test to reboot all, and eventually change the USBport, tomorrow morning (I am a little tired now and the eyes start to cross instead of read). As soon as I have done it I will and report here what does happend.
For now many thanks to you and to Xplode also.
night men!!!
Hope it works for you tomorrow... good luckits our pleasure to help.
Have you tryed the following ?
http://wiki.xda-developers.com/index.php?pagename=BA_FAQ_STUCK_AT_STARTUP
All Ok now
Symply from the last uprade of my 9090 I had changed the PC, so it haven't all the right Drivers.
Now, following Win XP requests (it was needing wceusbsh.sys) all is gone right so my 9090 actually exposes: CE OS 5.2.21169 (Build 21169.5.0.0) release. (and I am starting to play )
Many thanks to all.
you do not need drivers, install activesync in your pc, it includes al the drivers you need - if you have it and winxp still wants driver for the ba remove/uninstall activesync and reinstall it again - remember use the latest version of activesync
Hi,
Remove your "puce" and your sd card.
And try again of course with ActivSync.
For less worry upgrade on you BA's...I...WE recommend XP with Active Sync 4.5

Upgrade to 6 stuck on windows loading

Hi,
I got given a couple of Treo 750 phones. Both on the Optus Australian Network so I scratched around for days and found the upgrade software. Shows update 2.27
1st one went perfect.
2nd one on same computer got through copying files and executing update and stalled at the start of completing update.
I got the Windows mobile screen show and it just was not loading for ages. Previous one loaded and then asked for input of Date, touch screen settings etc.
The installer can be re run but says no USB connection at the moment.
I have done a hard reset and get the palm display then locks on the Windows Mobile screen.
I saw procedures to use the Mini SD card but the cards I have won't work in any treo, they are not SDHC type but standard 2G ones.
I next found the recovery tool but holding the left lower button and then hitting reset did not work but does work on my good phone where it shows the coloured bars and SPL....
The left button is a bit dodgy so I suspect it may be faulty. Is there anything else I can try?
EDIT: Ok I pulled apart the phone, looks like it had a hard life as broken case around two screws and they would not unscrew easily. Found the tiny button had dry solder joints. Fixed that up and was able to recover using the reset proceedure.
Phone now working.
could you explain in more detail what you did. thanks man
webafile said:
could you explain in more detail what you did. thanks man
Click to expand...
Click to collapse
What would you like to know?
Once I physicaly repaired the phone as indicated in the edit I was able to hold the left hand button (which was faulty) and the reset at the same time that allowed me to get into the SPL mode and recover the phone.
I understand it very little and most posts on these forums are over my head.
I would like windows 6.1 but there is so much information that seems to conflict that I don't know I am game since it is now working on an official 6.0 Optus version.
I am happy to help but if you can maybe tell me where you are at the moment and what you want to acheive and what you have tried I hope I can fill in the gaps for you.
because im new to this to and i got stuck in the windows screen also. so i would like to know what to download and where from and step by step if you could please.
thanks man
webafile said:
because im new to this to and i got stuck in the windows screen also. so i would like to know what to download and where from and step by step if you could please.
Click to expand...
Click to collapse
Ok to start with what country are you in and what telco were you with eg Vodafone etc as you will need that as a start.
USA and im with AT&A
Try the method describe in the thread below - Mine work
Hi, you might want to try this method
Follow it one by one and do not skip a step
http://forum.xda-developers.com/showthread.php?t=460783
I just did mine last Saturday (it was a Vodafone phone)
AT&T should be easier since the Windows 6 ROM is easier to get
If you'd like to update to WM 6.1, you should upgrade first to WM 6
Something i read about the radio not working to full capacity if you upgrade straight to 6.1
As for the WM 6 ROM, i'm sure you can find it
Good luck
Hi All,
I have a Treo 750 and it WAS running WM 6.0 Professional (OFFICIAL) and I got it onto the phone and then tried to install WM 6.5 and then I downgraded to 5.0 and tried to update back to 6 and it bricked my treo, any of you wonderful xda ppl have any solution?
Also, I have tried installing the ROM again (via SD updater) and it looks like this:
SPLASH1 OK
BOOTLOAD OK
GSM OK
Micro P OK
EXTROM FAIL
OS
Update Terminate
UPDATE FAIL
I cant install the windows installer one as WMDC 6.1 or ActiveSync 4.5 WILL NOT show the device up on the computer. I have Windows Vista Home Basic, and when I tried MTTY, the only ports I get are COM1, COM2, and COM3. I can't get the usb to show up. Even with MTTY 0.01 when I got the USB connection, it would not open. Is it Vista? Or am I not doing it right? ANY HELP WOULD BE APPRECIATED TO GET MY POOR TREO BACK!!!!!!!!!
Thanks
~Mike
Try this?
http://forum.xda-developers.com/showthread.php?t=427519
simunlocktreo said:
Try this?
http://forum.xda-developers.com/showthread.php?t=427519
Click to expand...
Click to collapse
Is this universal (i.e. Hermes/BA/Trinity) or just for the Treo 750. I think what bricked it in the first place was installing a custom rom by veisen (WM 6.5)
~Mike
Didnt Work
That one thing didn't work. It keeps coming up ERROR 226: FLASH WRITE ERROR Anything else???
~Mike

Unable to flash my ROM. Please help

I ave read the site a lot and have a major problem. I am unable to flash a new ROM. I know the problem is the SPL but am unable to update the SPL with neither HSPL nor a USPL.
To give some info, I am on Windows XP, Windows Mobile Decive Centre 6.1 (installeed, uninstalled and reinstalled a zillion times now). I have even tried updating a RRU driver ripped off from Activesync 4.5 but nothing really works. I do ave .NET 4.5 installed on my PC so that isn't a concern either.
Can you guys please help me and suggest a solution.
Thanks a lot for all your help in advance.
R
did u try by flashing your HD by SD Card I always do it that way my self and always works very good
handsome303 said:
I ave read the site a lot and have a major problem. I am unable to flash a new ROM. I know the problem is the SPL but am unable to update the SPL with neither HSPL nor a USPL.
To give some info, I am on Windows XP, Windows Mobile Decive Centre 6.1 (installeed, uninstalled and reinstalled a zillion times now). I have even tried updating a RRU driver ripped off from Activesync 4.5 but nothing really works. I do ave .NET 4.5 installed on my PC so that isn't a concern either.
Can you guys please help me and suggest a solution.
Thanks a lot for all your help in advance.
R
Click to expand...
Click to collapse
focus on one flash method, and concentrate to find out where you are doing wrong or what.
i suggest USPL 2.5, start in the Dummies guide here :
http://forum.xda-developers.com/showthread.php?t=505377
as you have windows xp, download the drivers here to update your sync driver :
http://forum.xda-developers.com/showthread.php?t=524619
and here is the procedure to actually update your sync driver: http://forum.xda-developers.com/showpost.php?p=3932818&postcount=2
going back to the first link i presented to you, download and unzip USPL GUI 2.5.zip to a memorable area in you pc. (I suggest you create a special folder, name it Blackstone Flashing, or whatever memorable term comes to your mind)

Categories

Resources