Hi
I have this problem if i want to update my SPL to HardSPL, i does not flased anything yet, because i get my phone today!
Try another version of HardSPL.
i second that use a differant one.
I tried all Versions of HardSPL but nothing works ...
btw. is it rght to go into the colored screen by turning off the phone, then turn it on with the volume down button?
depends what version diamond rom you have and to wich rom you want to upgrade, its usually mentioned wich spl is best in the rom-thread
rushing into this forum and blindly flashing can lead to a brick aka dead phone so take great care when proceeding
I'm having the same issues and I tried all the HardSPL versions myself.
once the upgrade begins, the phone screen just hangs and the installation is stuck at 0% for a while. After which it gives me either one of the following errors:
Error 202 Connection
Error 260 Connection
Only a restart of the phone will release it from the hang.
Yes I used it, but no luck.
@ some 1
even i got same problem with my diamond i m not able to understand where i went wrong...any help appreciated
same proplem
i have same proplem.. first everything looks just fine but when i try to update it stuck couple of seconds at 0% and then it gives error 202
same problem here..
+1
+1
+1
+1
+1
+1
+1.................
Related
hi everybody,
When I'm trying to upgrade my wizard, the process always stop at 99%.
I have try with several rom and it's always the same kind of problem. These just one Rom that is working the Wizard_Love_2.26.10.2.
Do someone have any clue of how to upgrade my phone with a wm6 rom?
Thank's a lot
How long have you waited? I've seen it sometimes take 10 minutes or something until it finished..
The windows sofware send me an error and then the update stop..
Your phone is locked. I had the same error, also need to lower your Rom.
I already have flashed my rom to a lowest one for instance "WM5SE rev 4.0 - WM5 without stylus but style" (this one work without any kind of problem). Then I have tryed to update with a WM6 one and it stop at 99% or I have the message "Invalid upgrade toll".
Do someone have had the same kind of pbl and solved it?
thank's a million
i had the same problem a few days ago and all i did was downgrade it to buttons rom and then upgrade it to the tomobile2.26 and everything installed correctly.
Hi all,
I have been visiting these forums for 2 years now and have downloaded some great tools and ROMs to enhance my Trinity, however something all of a sudden has gone very wrong!
I upgraded to WM6.1 Elegance edition about 3/4 months ago, CID unlocked the phone about a month ago and everything has been working like a dream.
However just today, I attempted to turn the volume down on my phone during a meeting (I always forget to normally!) and there was no display. After few battery resets, again no display. It starts up, loads the the Elegance splash screens and then hangs on the screen before when the OS should appear.
My decision was to flash the ROM again. I cant flash using Activesync as it wont pick up on the hung screen, so I started the bootloader and got as far as 1% of the flash and it will restart. So I tried the SD Card method when resulted in a "loading" screen appearing for a few seconds and then it goes back to the standard bootloader and displayed a 00068002 error.
I am out of ideas, I hear mtty.exe is a good program for this kind of thing, but what I want to know is if this is fixable or if I should give up!
I have been working on this since 2pm today none stop!
Can any of you guys give me any suggestions please?!?!?
Kind regards,
Jonathan
Should be a cinch
Did you SPL the Phone before flashing roms?
If you put the phone into the bootloader mode The RGB screen and kill of activesync you should be able to run one of the flash update programs.
If I have flashing problems its usually Active sync so I kill it then run the flash program.
I've got a sneaky suspision your battery might be causing the problem.
Hi there, thanks for the reply. As I was new to upgrading I havent used SPL on the phone before flashing the ROMS. I did use an unlock tool recently as i wanted to try a different network SIM to see if it worked when I was in South America, so the phone is unlocked to all networks. Are you saying if I SPL now it should sort the problem out? If so how do I do this withour ActiveSync working - can you use SD?
Another thing I failed to mention was that when I start an upgrade and it follows all the steps, it doesnt say the current ROM on the screen where you press update ROM. It just gives the name of the new ROM and the current one is left blank.
I have disabled Active Sync before attempting the update. It seems to go through fine and then the phone restarts wafter 1% of the update.
What makes you think it is the battery? I am happy to spend under 20 pound on ebay if you think it will fix the issue!
try unbrick.bat.......my trinity was also stuck.......unbrick.bat save my day....
The same happened to me several time....I could not find a solution other than this one:
1. Flash the official HTC ROM.
2. Flash the required ROM then.
it works for my TrinTy.
Hey everyone. I'm tearing my hair out trying to get this sorted but I just don't know what to do!
So, when I got my X1 as everyone on here should do, was flash my X1 with the HardSPL and some custom roms, this was a few months back. Then, shock! Horror! My case went and broke, (cracked near the volume button build W44) so I sent it back to SE for repair. I sent it back reset back to defaults but left the hardspl on there.
SE sent me a brand new phone (I think... This one says under the battery build w50, but the battery says w32..) I received it today. I thought it would be my old one repaired but SE had other ideas. Booted up and have Image Version: 1.03.931.10 and HardSPL 72.000 I think I said that correctly...
Now since sending it for repair and receiving it back, their seems to be quite a few wm6.5 roms floating about, and obviously I can't use the stock software as that wouldn't be right!
Now I have tried flashing the hardspl to the phone through my Vista PC and all it keeps giving me is connection errors. I thought maybe it was already flashed so I tried flashing just a rom, and that just made the phone get stuck on loading (flash by memory card). I thought it might be Vista, so I tried doing it on my other PC (XP) and I get the same issue. This bloody thing won't flash!
I have had "Connection Problems" - "Update Errors" with different numbers. The current one being Error [260] CONNECTION.
Now I have been searching around through the hardspl thread and other places trying to find out what I need to do or how I can fix it, but everything I try doesn't make a difference. I did read some other people with recently repaired phones having the same problem and perhaps SE have put a new spl thingy-ma-jiggy on there. (Please forgive the technical jargon, I have no idea what im on about.) I have also tried the ticking/unticking advanced network functionality, but that hasn't made a difference either.
So by the end of typing this, I have little hair left. Let's hope you can all help, before I have none left!
I would appreciate ANY help! Really.
Just wanted to add, I was at first getting the phone to a loading bar when flashing, but it would stay at 0% then flag up an error on the PC. Now after the tri-colour bars, the phone just sticks on Loading...
Well just to update. I have been trying to sort this since posting. I flashed the rom to an old UK generic one, as I read in another topic people had to do that before HardSPL. Done that, and tried flashing the hardspl. Same thing, just getting connection errors.
I tried going into bootloader and running the hardspl from there. It works and the phone gets to 10% and then gives an UPDATE ERROR. The phone is now bricked, and I have to reflash the original wm rom to get it back.
Though the Tricolour screen now shows 0.52.Olinex
Any ideas?
Shameless bump for help.
very stupid situation.
i have the same situation in puncto of flashing.
i get my phone three month ago.
after hardspl i .... sorry, no hardspl ... the phone says at 0% bla bla bla
i solve the problem by consulting one night absolutly stressing again and again and again .... google ... xda ... google
than 3 thinks at one time was the solution:
0. need activesync - connect !!!!
1. SDA_ApplicationUnlock.exe for desktop pc
2. enterbootloader.exe for pocketpc (please, the right version, it exist for eten too, but we need the xpediaversion ..)
3. changing registry-entries
how to:
activesync-connect, than copy "enterbootloader.exe" to pocketpc. it must be root, not sd-card. use a pocketpc-registry-program to change these values :
HKEY_LOCAL_MACHINE\Security\Policies\Policies\00001001 = 1
HKEY_LOCAL_MACHINE\Security\Policies\Policies\00001005 = 40
HKEY_LOCAL_MACHINE\Security\Policies\Policies\00001017 = 144
HKEY_LOCAL_MACHINE \Security\Policies\Policies\0000101b = 1
if not exist than add the key.
now, start desktop-program, follow instruction EXCEPT reboot.
start "enterbootloader.exe" on pocketpc. now, you can install hardspl and the device is flashable for ever.
thats works on me, hope it could help you too.
Thanks for the reply. Not had time to try it till this morning. Ok so, after spending about an hour trying to find the correct enterbootloader.exe I finally realized, that the hardspl package includes it. *Duh!* So that was time wasted.
I changes the registry values as you said with Resco registry editor, and follower the unlock then enterbootloader.exe Start HardSPL package. Starts to install. Gets to 10% then I get
ERROR [262] : UPDATE ERROR
The rom update utility has encountered communication errors during the update process.
So im open to suggestions if anyone has any. I just can't understand why it's not working. It's not a problem with my computer or cables. I flashed the phone before I sent it for repair and I have tried doing it on two computers one with XP 32bit and one with Vista 64bit.
hmm. would u like to install a custom rom, or a stock rom?
msg me, and i hope, i can halp u.
I want to have the hardspl on there so I can flash custom roms.
If it's a case of the software/firmware/hardspl whatever you call it, has been updated by SE. How would one go about getting it flashed? Would we have to wait for an update HardSPL to be released?
U read this thread?
My first hardspl was from this thread. New X1 will come tomorrow back from SE (vibration was defect +++ some more problems with case), and i will try it again with this thread.
hope, this will help u mate.
Yeah, I have been through that thread with a fine toothcombe trying everything suggested to see if I can make it work.
When you get yours back, if you have to do anything out of the ordinary to get it to flash or can't do it. Please come and let me know in this thread. If they have updated yours like mine, and yours won't flash, at least I won't be the only one!
k, i will msg u tomorrow around 2pm.
Cheers.
In the meantime. Does anyone have any other suggestions I could try?
Bump, for some help.
now i know, what is exatcly your problem.... <--- SAME Problem
i hope, i will find a solution and msg u then. if u´ll got a solution for this prob, msg me too plz.
Solution found in this Thread!
Download this and unzip it to your device. ++ run it. It will start your X1 in Bootloader menu and say "0.52.OliNex".
Then start hardspl while X1 is in Bootloadermenu....
FINISH =)
Thanks for the reply matey. Glad you got yours sorted. Just tried what you said and I get 0% then it switches to ERROR [262] : UPDATE ERROR.
vwrmic said:
Thanks for the reply matey. Glad you got yours sorted. Just tried what you said and I get 0% then it switches to ERROR [262] : UPDATE ERROR.
Click to expand...
Click to collapse
hmmm... it works fine on my new x1. are u sure, that u start the ssplmanual on your x1 and not on your computer?
Yea, im not sure what the problem was with it. Thankfully I have it done and dusted today! Because I flashed it earlier to an older official version, and you said you got it working. I presumed you had - had yours flashed to the newest version due to it being off for repair. So I reflashed the official update and fully updated it. Then tried hardspl which didn't work. Tried with the advanced USB thing off, tried again with how you said you did it above, and Viola!
Hip hip hoorah! Thanks for the help. Can finally use me bleedin phone now!
no problem mate hf with your x1
hello,
i see smilies and yea's ...
for me to understanding (for next time or other users):
1. complete official update (if exists)
2. flashing (hardspl) without "advanced usb"
thats all?
cool.
I've been lurking with the XDA forum for quite sometime now and its my very first posting and I'm having difficulties finding answers on search box I just simply give up looking for appropriate answer to my question. Since I like to use the good old Winmo 6.1 rom (Davideuck_V-7_MSVC to be exact)my bad is I forgot to SPL to earlier version 1.15 so got a green kinda thing on my screen, so I apply Restore_Stock_SPL_115 and everything went fine. (I know I'm stupid ) Unfortunately after I update the Time and Date it suddenly appear " This concludes the beta test for this software release....... blah, blah,.... guess what? its a time bomb can't do anything on screen but to reset. So I decide to re-flash it again but I got stuck at 0% on bootloader mode and got Error 262, I tried to understand whats the meaning of it and I did, but never got any solution how? I tried to flash it with HSPLWrapper_Blackstone_156OliNex to restore Winmo 6.5 but I got stuck again on 0%. something unusual I tried to reflash more roms and it didn't work. All the Roms I've wont reach 1% Even flashing on SD card trick wont load. And my spl ver 1.15 can't flash anything. So I that's why I need your help desperately...
Near enough the exact same situation as me! I think that 1.15 file may have issues.
wayneroughneckz said:
I've been lurking with the XDA forum for quite sometime now and its my very first posting and I'm having difficulties finding answers on search box I just simply give up looking for appropriate answer to my question. Since I like to use the good old Winmo 6.1 rom (Davideuck_V-7_MSVC to be exact)my bad is I forgot to SPL to earlier version 1.15 so got a green kinda thing on my screen, so I apply Restore_Stock_SPL_115 and everything went fine. (I know I'm stupid ) Unfortunately after I update the Time and Date it suddenly appear " This concludes the beta test for this software release....... blah, blah,.... guess what? its a time bomb can't do anything on screen but to reset. So I decide to re-flash it again but I got stuck at 0% on bootloader mode and got Error 262, I tried to understand whats the meaning of it and I did, but never got any solution how? I tried to flash it with HSPLWrapper_Blackstone_156OliNex to restore Winmo 6.5 but I got stuck again on 0%. something unusual I tried to reflash more roms and it didn't work. All the Roms I've wont reach 1% Even flashing on SD card trick wont load. And my spl ver 1.15 can't flash anything. So I that's why I need your help desperately...
Click to expand...
Click to collapse
If you are getting an Error 262, you need to run manual sspl in order to resolve this. Read this post for the steps (post #2) and sspl tool (post #1) - http://forum.xda-developers.com/showthread.php?t=505377. You can also get all of the steps needed to successfully flash. if you have questions, please post them in that thread.
It seems when I restart my phone normally, I noticed that the message about " This concludes the beta test for this software release....... blah, blah" the manila interface was behind it when I press the task manager and the volume buttons it responses means its not bricked (hope so) maybe the reason why I cant flash anything? Or whatever...Well that's my observation..... Please guys I needed my phone badly tomorrow
Did you not read my post . You can flash another rom, error 262 is common. You just need to use sspl before flashing to hspl 1.56.
if ur stuck with hspl and cant flash that than try uspl or try stock rom.... they get installed without hspl or uspl installed.... its available in the blackstone wiki section
and with stock rom get through tomorrow . than try hspl or uspl with custom rom later on when u have free time
Upgrade the ROM with latest official HTC release it upgrades the bootloader to ver 1.54 as well. Then you can install the newest version of HSPL or just use USPL to flash whatever cooked ROM you want.
Apologies on replying again here instead of posting on the designated thread , but forgive my innocence the thread says "" launch SSPL-Manual.exe from attachment, run it, wait until 1.07.OliNex tricolour screen says "USB" on it, then run the HardSPLWrapper_Blackstone.exe on the PC. "" how exactly that's going to be done? Currently I got the tri-color screen saying SPL-1.15.0000 and a USB on the bottom and when I flash either hspl or uspl I always end up on gray screen with a 0% that doesn't move at all, how can I manually apply SSPL? I cant access Manila interface because of time bomb message? My life's getting complicated!
If possible try flashing from an XP box, Vista/7 might give you some additional trouble if you don't use the right drivers. But if you get to the 0% screen, the issue shouldn't be with the SPL... so don't worry, I doubt the phone is bricked
So: try XP and/or using the drivers provided in the Flashing-thread
zerozed said:
Upgrade the ROM with latest official HTC release it upgrades the bootloader to ver 1.54 as well. Then you can install the newest version of HSPL or just use USPL to flash whatever cooked ROM you want.
Click to expand...
Click to collapse
I tried the Official one Blackstone_WWE_1.56.405.1 and got Error[294] Invalid Vendor ID
wayneroughneckz said:
I tried the Official one Blackstone_WWE_1.56.405.1 and got Error[294] Invalid Vendor ID
Click to expand...
Click to collapse
Did you downloaded the ROM from the HTC site? If the ROM is from the official site try again using USPL.
I seach the wiki page and found the latest version which is "Blackstone_WWE_1.56.405.1" and I can't find it on the official site, it should be "WWE" not specifying on certain countries, so I manage to download it from Rapidshare link. and for the SSPL I don't think I can do that coz I can't access my phone coz it has tim bomb probably the main culprit here.
Any flashing problems should be posted in Dummies Guide thread.
Thread closed
Hi folks,
i used several roms from here, worked nicely.
had spl 1.33.OliNex i downloaded latest energy rom and did update from SD.
it wrote update success, then i reseted topaz.
now im stuck on boot screen with tmobile logo and RDG message.
i tryed to upgrade radio and do the flash again but again success message and screen hang on tmobile logo. tryed hard resets etc, same result.
i just got
R 4 49 25 91
G 61.44etc 25 35U
D2.13.64695
message on bottom, nothing more.
i wonder if its not problem that i have older hspl, but i dont know how to upgrade it without having system booted and connected to PC...
Anybody can help me?
-------------------------
managed to update spl to 2.51,
did the flash again, again success message and this time it runs
So, maybe it will at least help other ppl
grapher said:
Hi folks,
i used several roms from here, worked nicely.
had spl 1.33.OliNex i downloaded latest energy rom and did update from SD.
it wrote update success, then i reseted topaz.
now im stuck on boot screen with tmobile logo and RDG message.
i tryed to upgrade radio and do the flash again but again success message and screen hang on tmobile logo. tryed hard resets etc, same result.
i just got
R 4 49 25 91
G 61.44etc 25 35U
D2.13.64695
message on bottom, nothing more.
i wonder if its not problem that i have older hspl, but i dont know how to upgrade it without having system booted and connected to PC...
Anybody can help me?
-------------------------
managed to update spl to 2.51,
did the flash again, again success message and this time it runs
So, maybe it will at least help other ppl
Click to expand...
Click to collapse
Did you try going into bootloader first and then running the RUU.exe?
Or you can look HERE about making a Goldcard with Qmat (#6)
EDIT: Didn't see that you updated your post, congrats on gettin it workin again though