Database Develop

Did I do what I hoped I wouldn't?

Well, after hours of research and searching and reading, I finally decided to flash my T-Mobile Wing. Yay! First, I did Hard-SPL from HERE and followed the instructions to the point. The CanonYang splash screens came up and my Wing loaded into Windows Mobile just fine. From there, I installed ASerg's policies again and ran Itje's Touch-IT Lite for the Wing "1__UPGRADE_ROM.bat" and followed the instructions it prompted me with. An error screen came up on my phone saying "Unknown Status" but I just left it alone. After about 10 minutes, Itje's RUU completed and I hard reset my phone.
Now, only the first CanonYang splash screen comes up and my phone locks up there. Did I just brick my phone? What do I do to fix this?
Any help is greatly appreciated.
*EDIT* In my haste and fear of the "brick", I chose to post a thread rather than do the obvious that many will most likely state. If it helps my situation, please note that it's nearly 5am in Chicago, I have not slept yet, and I'm pretty much terrified I just made a $300 paper weight. I'm certain many of you would do the same.
Yes, I did fix my problem... and yes, I found my answer by searching the forums... and yes, I will buy you all cookies! Itje gets a candy bar though

lol soz
press the camera button and at the same time use the stylus to push the reset ..... a colourful screen will come up ...... connect it to your computer and run a official rom..... you can either look from some or get windows mobile 6 from htc.com if you sign up to the eclub and just find it from there.
hope this helps

Tilt Touch Screen failing after loading Dutts latest ROM

Hey there,
A bit new, just finished loading Duttys WM6.1.5.2.1972_Hybrid_V2_1_65.14.06[CubeV2] Rom. Seems great at first. Had to download Goodlink for the corporate stuff. It works fine for a bit, but as soon as an Outlook reminder pops up, suddenly the touch screen is completely dead. Tried all buttons etc on the front. The keyboard works and the buttons can be used as the menu choices, but it took a hard reset to fix it. Which then I had to reload Goodlink and it happened again.
Any patches or settings anyone can think of? Goodllink is the only add in I put in. Any other ROM's recommended perhaps? Thanks all!

Borg7of9 said:
Hey there,
A bit new, just finished loading Duttys WM6.1.5.2.1972_Hybrid_V2_1_65.14.06[CubeV2] Rom. Seems great at first. Had to download Goodlink for the corporate stuff. It works fine for a bit, but as soon as an Outlook reminder pops up, suddenly the touch screen is completely dead. Tried all buttons etc on the front. The keyboard works and the buttons can be used as the menu choices, but it took a hard reset to fix it. Which then I had to reload Goodlink and it happened again.
Any patches or settings anyone can think of? Goodllink is the only add in I put in. Any other ROM's recommended perhaps? Thanks all!
Click to expand...
Click to collapse
I notice this is your fisrt post so welcome. There is a great deal of helpful experience here to help but it does certainly pay to pose questions in the correct place. If you ever have a question about a ROM then post your question in that area and you will be far more likely to get the helpful anser that you want. People are also sometimes too quick to 'Flame' people making such errors - but not me so hopefully this will help:
I am on that same ROM and have noticed that after initial ROM installation that the touch screen is initially 'prone' to what appear to be freezes. In fact I noticed on my device that I had to press quite hard to get any interaction with the screen and sometimes it did not respond.
Cannot say why but this has now completely gone and did so with each ROM install. It took a few soft resets to see the screen working correctly but it is great now! So it may not be your additional software. Just try sticking with it for longer and some soft resets. You might also try tweaking the sensitivity of the screen.
Suggest you search within the correct area and you'll see few comments about this kind of thing (but not many).
Regards

Thanks Tony. My first time posting so wasnt sure where to put it. Have done all you suggested. Worse case, back to the ATT rom, oh well. Will search also and try posting in the right location. Thanks!

Borg7of9 said:
Thanks Tony. My first time posting so wasnt sure where to put it. Have done all you suggested. Worse case, back to the ATT rom, oh well. Will search also and try posting in the right location. Thanks!
Click to expand...
Click to collapse
i just reviewed the software online and i can make several predictions why this is conflicting with the rom. 1) htc home
go to settings>personal>today>items>and uncheck htc home.
let me know if goodlink works thereafter if not I have a few more predictions to why it doesn't operate correctly.
Oh, and i just noticed you had a cube version, which could also be conflicting.

Thanks for the input Red. Tried that to no avail. Even tried soft reset afterwards. It is dead before goodlink even starts. BTW, this will be worth a Pint or two if you get me working.
I thought it might be the Cube version so after several hard resets(storage clearing), I went ahead and flashed it with Dutty's Non Cube version just to see if that was it and it wasn't. I tried tuning the touch screen too, bumping sensitivity up to 200, didnt help either. Tried loading the tweaks program, but nothing there either helped(actually cant even use it when frozen). The keypad, buttons all work, but the touch screen is dead. Hard reset fixes it, loading Goodlink, which I have to have for its a corp phone, kills the touch screen. I believe it worked for a few minutes, then locked up. I need to reverify that just to make sure it didnt happen immediately with Goodlink install. Very strange.

Kaiser bloatware

Hi, I'm just turning on my 8925 for the first time and before setting it up I want to remove all the trial stuff. I set up, soft reset when the "3 seconds customization" comes up, but when the device turns back on, it takes me back to set up again (screen align, password, etc.) I've done this before with another Kaiser and I know it works, but this one keeps recycling the whole process. I've gone through the clear storage, set up, soft reset several times already and it's the same each and every time. What am I doing wrong?

I would keep resetting and if it still continues trying to install the bloatware, dump the rom and go with some of the other great ones. L26 Kaiser Diamond Rom V12 has been good for me lately, Schaps has some good ones ot there too. Those roms will better utalize the hardware on your kaiser. Hope this helps...

I'm so fed up with this. I going to stop now since I think too many resets will screw with the device. I'm starting to wonder if this is the same as the last Kaiser I had. For once there's a new green "window mobile 6.1" screen right after the AT&T logo at start up, which my other tilt didnt have. The screen says to wait while it's clearing storage everytime I do a hard reset, then take me to set up again, then back to the 3 seconds of bloated wares. Rinse and repeate. Another difference is that this one came with HTC Home today home screen the one with the big digital clock and tabs.
Could it be this is a used phone and the previous user loaded it with a different ROM?

You need to soft reset BEFORE the 3 second notice comes up...if the box pops up, you're too late and need to wait to get to the today screen once again. Remember...BEFORE...either way, there are many really nice ROMs out there...

Ah hah! Voila, you are THE man! Thank you thank you! <3
Still strange that this one came preloaded with HTC Home plug-in, though. But Im happy either way

My sister got a Tilt today and had the same issue (I tried to guide her over the phone to ditch the bloatware - she won't be flashing ROMs anytime soon...)
Hers contains the HTC Home plugin as well.
They've apparently updated the shipping ROM...
Glad to hear that it works fine before the 3 second box.

You'll be able to remap the PTT button right out of the box also. Good stuff.
Im just hoping this one doesnt have battery problem like the one I got before. I kept it as long as I could, even got an extra power battery for it (since the stock one drained after maybe 6 hours), until the damn thing heat up so bad while being charged that it almost burn my hand...
Been charging this one for a few hours and no heat problem yet!
/fingers crossed

You should really try a Manilla ROM--they are easy on the eyes, very nice interface...look up NATF or the AthineOS Manilla ROM. Both guys did a fantastic job on those...
NATF http://forum.xda-developers.com/showthread.php?t=424725
Athine OS http://forum.xda-developers.com/showthread.php?t=435345
But, make sure to read the WIKI
http://forum.xda-developers.com/showthread.php?t=369282
Search around, more than likely, that question on your mind may have already been answered.
There's no such thing as a stupid question, but they are the easiest to answer...

'preparing your device for first use'

Hi folks, I've been using abusalza's Ulitmate-X roms for a good few months now, and recently I decided to update to his WM6.5 beta version, after doing that whenever the phone needs a soft reset, it will boot and say 'preparing your device for first use', and format everything on the phone and then boot up.
So I decided to flash his Ultimate-X2 V11 rom, same issue, and now I've gone back to his Ultimate-X V9, which I'm pretty sure is the same ROM I've been using for some months now (never had any issues before), and whenever it requires a soft reset it will do the 'preparing device for first use' thing, it will do the customization install, then the connection setup, then reboot itself and just sit there on the PDA Corner Ultimate screen until I reset it, soft resets just keep hanging on the PDA Corner Ultimate screen, and unless I hard reset it (soft keys and press the reset button, that's a hard reset isn't it?) it won't get passed that point. I've just this minute had to hard reset it and it's booted, but it takes a good 5-10 minutes each time which gets annoying.
Has something packed up in my Kaiser to make it do this? Seems out of 3 ROM's I've tried they all now have the same issue, including a ROM I'm pretty sure I used to use with no issues.
Sorry if this is a common problem and easy to cure, I did search for 'preparing your device for first use' and something came up from months ago, but a totally different issue.
Thanks for any advice, Dom.

duuuuuuuudddeeeee!!! you have made TWO basic mistakes
1. this post belongs in the thread for the ROM you are using (same series as myself) where you will find...
2. you need to flash stock ROM first!!! it is written on the FIRST PAGE of the thread...i mean seriously, EVERY DAY on that thread, you will see this pattern:
noob writes a post..."my device hard resets after soft resetting...your ROM sucks, etc, etc"...then someone directs them to the instructions on the first page of the thread and problem solved. afterall, the instructions are there on the first page so that people can read them along with the FAQ.

I'm sorry!
I'll not bother you again I promise *goes to read the FIRST PAGE of the ROM topic*
The only reason I've never done this before is because I'm sure I've flashed ROMs in the past and not had to go back to OEM first
Thanks a lot, I'll go have a read now.

Dommo said:
I'm sorry!
I'll not bother you again I promise *goes to read the FIRST PAGE of the ROM topic*
The only reason I've never done this before is because I'm sure I've flashed ROMs in the past and not had to go back to OEM first
Thanks a lot, I'll go have a read now.
Click to expand...
Click to collapse
Well at least you didn't start a new thread in the rom development forum
And the OEM first, appears to be a 6.5 only thing, so how would you know...
But I still won't forgive you for not reading the first page or the FAQs. When the doctor gives you new medication to get rid of the flu, do you read the label , or do you just take two or three and figure that should be enough.

denco7 said:
Well at least you didn't start a new thread in the rom development forum
And the OEM first, appears to be a 6.5 only thing, so how would you know...
But I still won't forgive you for not reading the first page or the FAQs. When the doctor gives you medication to get rid of the flu, do you read the label , or do you just take two or three and figure that should be enough.
Click to expand...
Click to collapse
[sarcasm]I always thought the best way was to take all the pills at once? No wonder I feel a bit rough afterwards [/sarcasm]
I do feel like a tool at the moment so that's something to be chuffed about
Cheers, just downloading another updated rom and I'll give that a go, it's back to OEM now.
Thanks again.

another bricking question

My unbranded TyTnII took a dump today, and reset itself to OEM condition, not so bad, except the data base was corrupt, so I would not configure a connection to my carrier (T-mo) .
So, I took it home, hooked it up to activeSynch, and brought up a previous sprite backup file to restore it.
Now it's a paperweight- it will start, display the three three install lines R-G-D with the Smart mobility splash, and that's it. I can't get it into bootloader, or anything else for that matter. Any ideas?

ttruex said:
My unbranded TyTnII took a dump today, and reset itself to OEM condition, not so bad, except the data base was corrupt, so I would not configure a connection to my carrier (T-mo) .
So, I took it home, hooked it up to activeSynch, and brought up a previous sprite backup file to restore it.
Now it's a paperweight- it will start, display the three three install lines R-G-D with the Smart mobility splash, and that's it. I can't get it into bootloader, or anything else for that matter. Any ideas?
Click to expand...
Click to collapse
If you get to the 3 color screen you are in bootloader my friend, do you notice the USB sign display in the screen? If you get that you can flash. I will recommend that you hard spl your device first (Please read the sitcky of how to perfom it, click under my TyTNII link)

Moved as not ROM Development..
Hard-Reset and do not use your backup as may be corrupted...
If that does not work then try and get into bootloader i know you said you can't but try again and flash stock ROM.

thanks for the move, and my apologies for the mispost- I realized only afterward I had put this up in developers.
I can't get to bootlogger mode- the phone hangs at the initial splash where it displays the SW versions of R D G. It will not move past this.
I hold the camera and on buttons, and push and hold the reset pin, but this is as far as it gets. I will sit here, so far for an hour, but will not progress further.
What am I missing? It's been some time since I've had to muck with it at all, so I've become unfamiliar with the tricks.

It's not bricked as long as you can get meaningful info on the screen. It sounds like you need to revisit HardSPL and put on a newer version. Then flash an appropriate rom.

All right,
Many thanks for the help! I flashed and manged to get the bone stock HTC WM 6.0 ROM loaded.
Now, at the risk of asking what could be considered a dangerous question (almost as bad as starting an oil thread on a moto list) what would be considered the latest and greatest ROM of them all? these days? I haven't been on this forum for quite some time, and I'm sure you all have been busy w/updates. I gave up when WM 6.1 came out, screwed up the GPS settings and made the camera even worse, so I've just stuck with my plain 'ol HTC OEM ROM.
Any suggestions?

ttruex said:
All right,
Many thanks for the help! I flashed and manged to get the bone stock HTC WM 6.0 ROM loaded.
Now, at the risk of asking what could be considered a dangerous question (almost as bad as starting an oil thread on a moto list) what would be considered the latest and greatest ROM of them all? these days? I haven't been on this forum for quite some time, and I'm sure you all have been busy w/updates. I gave up when WM 6.1 came out, screwed up the GPS settings and made the camera even worse, so I've just stuck with my plain 'ol HTC OEM ROM.
Any suggestions?
Click to expand...
Click to collapse
Yes, try them all and pick which one can meet your daily needs

having tried quite a few 'light and fast' types, i would say stick to more or less standard 6.1.
i spent a lot of time looking for cabs and then adding back in all the removed stuff i needed.
then get spb mobile shell on there and have a good looking phone.
6.5 never worked properly, esp messages, but a few other obscure probs.
my 2c