Hi,
Ive got an annoying little problem with the button on the handsfree kit of diamond. Basically, I just use the handsfree for music but often, by accident, the answer button on the kit is pressed and this leads to the phone dialling the last-called person, now this is pretty damn annoying, especially 8oclock in the morning..
Basically, I want to know if it's possible to disable this button altogether or to stop it from dialling last dialled number when pressed? If not I might end up breaking it lol
Related
Hi:
I've been searching for info how to achieve the following, which I can't get done so far:
I have stereo bluetooth headphones with a mic. These are great for receiving calls, when you don't have the phone easily accessible, like in the car etc.
They have only two buttons, one is a two-way joystick for loudness. The other one is a receive/hangup button using which you can accept incoming calls.
What I'd like to do is to enable it to activate voice dial when I press it, to make a phone call.
So far I've only discovered that if I hold it depressed a long time, then the headset redials the last-dialed number.
In some instances after a call, when I've pressed the button, voice dial has come up and asked for the called id, however I cannot replicate this behavior, and it doesn't do it when the home screen is visible. Only I think after I've dialed from the headset, then hang up. Then at that screen press the button, but it's not stable.
So it seems though, to use the button to activate voice-dial is possible. I'd just like to set it up so that it works.
Anyone know how to?
Try holding one of the buttons
Depending on the BT adapter, you might have to hold down the receive/hangup button till you hear a confirming beep.
its usually a short press for voicedial a little longer press for redial last number. so try just doing short press insead of holding it down
or any on screen buttons in the HTC dialer. anyone know how to get rid of it? its supppper annoying
A little more information would be helpful -
1. does this tone happen when you press a button while on a call?
2. if it does - does your other party hear it or only you?
3. what buttons does it happen on touch screen buttons or only the buttons on the front of the phone?
4. is this when you have speaker phone on or a headset or simply using the phone?
5. is it only when you hang up or any button at any time while on a call?
6. do the buttons make normal sounds when you are NOT on a call?
7. have you turned off sound on your buttons - have you at least tried this to see if it kills the problem?
Bill
when in the dialer go Menu->Options then Keypad: Off
ahh keypad tones off got rid of the annoying beep lol thanks! wish there was a way i keep the beep for the numeric keypad without the obnoxious beep that came out of the speakerphone part rather than the ear piece when backspace/ call history/ speed dial is pressed
jut realized it still makes the annoying noise when it connects to a call
i found that someone had my exact problem on a wings smartphone. they edited the registires in order to turn it off. i played arround with mine all day but no luck. here is the thread if anyone can apply it to a kaiser id be very greatful!
http://forum.xda-developers.com/showthread.php?t=356416
Hi All
I recently lost my ringtone and found a solution on here, so all is fine.....EXCEPT when the phone rings, the ringtone disappears when the scroll wheel (if that's what it's called) is moved.
Has anyone else come across this problem and if so found a fix???
The phone carries on ringing silently if I move the wheel, it's just the sound that disappears and that's obviously not very good if it's in my pocket!!
I've tried pressing all the other buttons when it's ringing to see if they make the sound disappear but they don't, it's only the wheel
Any one got any ideas????
Thanks
That's not a bug.
That's a feature...
My TyTN1 did that.
My P3600 did that.
My TyTN2 Does that.
It's the only way of making the phone go QUIET without canceling the call.
Quite usefull actually....
Honestly!!??
It's a feature??
How do I turn it off????
I like that feature very much, too. When someone calls and I don't want to talk to them I just hit the scroll wheel to silence the call but let it continue ringing for them. That way they don't know I'm ignoring them. I can plausibly be out of range of my phone or some other excuse. If you press the end key or hit "ignore" on the phone screen it sends the call immediately to voicemail and the person on the other line can tell they've been actively ignored...
I don't know if it's possible to turn it off.
ive always found it usefull. but sometimes it can be annoying as OP said when its in your pocket
livefastdiefun87 said:
ive always found it usefull. but sometimes it can be annoying as OP said when its in your pocket
Click to expand...
Click to collapse
The beginning of every sad story I've heard about screen cracks and phone damage, has always begun with , Well the phone was in my pocket and..............
When I pull my phone from it's padded holster I always look at the caller id first and do not wish to disturb other people while I decide. I appreciate the feature
I'm guessing it's a feature that can't be turned off then
Hi I searched in this forum but could not find the answer, is there any way to disable the wheel during a call? i hold phone in my left hand, and even with screen locked, the wheel turns so the screen unlocks, leading to my ear pressing the soft buttons on the screen, which is a problem because often my ear presses the end button!
Use the speaker phone option. You can hear the person on the other end without picking up the phone....
bump - any love here?
phone canvas?
I was having the exact same problem, but now I use AE Button Plus. I set the scroll wheel to only be active when the today screen is active. It works perfectly.
We have a couple of Tilts and two are having the same issue, one more then the other.
Every so often when trying to make a call, it connects but the caller cannot hear anything. Sometimes if the power button is pressed the call can be heard. A soft reset also cures the problem for a while. Both are running 6.1
Mine has never been dropped, I am noth sure of the other user.
Any ideas?
Thanks,
Larry
Sounds like the NSIC (no sound in call) issue. There is a pretty lengthy thread on this and the prevailing wisdom is that this is caused my MS Voice Command, and no solution. You will fins, if this is the issue, that you can also fix it when it happens by going to settings and toggling VC off/on.