ROM Update not stored (after splxploit) - P3600 Software Upgrading

Hi,
My Trinity (s300+) stops working yesterday night : it was buggy, so I decided to do a soft reset, but then after it starts I get the splash screen for 1 second and it turns off. I tried a hard reset but nothing change.
I tried "splxploit" in order to have a HardSPL installed and then to flash a ROM through a SD but the problem is that the update looks OK but is not stored in the phone:
- when I entered the bootloader I had :
TRIN100
IPL-0.50
TRIN100
SPL-1.07.0000
- after running "splxploit" I had on the screen:
TRIN100
IPL-USPL
TRIN100
SPL-1.20.Olipro
- after doing a soft reset and reentering the bootloader I have again:
TRIN100
IPL-0.50
TRIN100
SPL-1.07.0000
Is there something wrong with what I am trying to do, or should I start considering that it may be now a brick ?
Thank you for your help,
Mika

mikahtc2 said:
Hi,
My Trinity (s300+) stops working yesterday night : it was buggy, so I decided to do a soft reset, but then after it starts I get the splash screen for 1 second and it turns off. I tried a hard reset but nothing change.
I tried "splxploit" in order to have a HardSPL installed and then to flash a ROM through a SD but the problem is that the update looks OK but is not stored in the phone:
- when I entered the bootloader I had :
TRIN100
IPL-0.50
TRIN100
SPL-1.07.0000
- after running "splxploit" I had on the screen:
TRIN100
IPL-USPL
TRIN100
SPL-1.20.Olipro
- after doing a soft reset and reentering the bootloader I have again:
TRIN100
IPL-0.50
TRIN100
SPL-1.07.0000
Is there something wrong with what I am trying to do, or should I start considering that it may be now a brick ?
Thank you for your help,
Mika
Click to expand...
Click to collapse
Hi,Mika maybe I can help u to upgrade ur SSPL,busy now maybe I will send to u later,K

Try here,maybe this can help u.
mikahtc2 said:
Hi,
My Trinity (s300+) stops working yesterday night : it was buggy, so I decided to do a soft reset, but then after it starts I get the splash screen for 1 second and it turns off. I tried a hard reset but nothing change.
I tried "splxploit" in order to have a HardSPL installed and then to flash a ROM through a SD but the problem is that the update looks OK but is not stored in the phone:
- when I entered the bootloader I had :
TRIN100
IPL-0.50
TRIN100
SPL-1.07.0000
- after running "splxploit" I had on the screen:
TRIN100
IPL-USPL
TRIN100
SPL-1.20.Olipro
- after doing a soft reset and reentering the bootloader I have again:
TRIN100
IPL-0.50
TRIN100
SPL-1.07.0000
Is there something wrong with what I am trying to do, or should I start considering that it may be now a brick ?
Thank you for your help,
Mika
Click to expand...
Click to collapse
Mika,please download from here http://forum.xda-developers.com/showthread.php?t=293632
Down load SSPL-Trin.Zip and unzip it,or try to use "WIN RAR" software to unzip,copy SSPL-Trin to ur device,click on it bootloader will prot out,plug in cable wait for Sync(Screen will show "USB"),download rom in progress,follow instruction untill finished,pull out cable soft reset ur device
Good Luck,Mika
From Eddie (Malaysia)
Email : [email protected]

Thank you for your answer.
Unfortunately, my problem is that I cannot run a program on my Trinity since I cannot start it anymore (I just got the splashscreen, and it turns off).
I can also start with the bootloader mode and this is why I tried the 'splxploit' .
Hope there is still something to do to heal it
Mika

mikahtc2 said:
Thank you for your answer.
Unfortunately, my problem is that I cannot run a program on my Trinity since I cannot start it anymore (I just got the splashscreen, and it turns off).
I can also start with the bootloader mode and this is why I tried the 'splxploit' .
Hope there is still something to do to heal it
Mika
Click to expand...
Click to collapse
Hope this will help ur device wake up again.
1.)RUU_Trinity_DOPODASIA_WWE_3.00.707.18_6275_1.46.30 .11_108_Ship.exe
Down load this and extr it,u can see few files and look for the file name RUU.xxx.NBH file,and just rename it as TRINIMG.nbh
2.)now you must use Mini SD,format it to FAT 32,with no Volume Label(go to folder right hand click and format it to FAT 32 at FAT colum,after that erase the volume label etc "KINGston"farmat card.
3.)copy file TRINIMG.nbh to your Mini SD Card,now ur screen blank right?slot in MiniSD,now boot from card,you will see "loading"follow by "checking" then it will prot out some like Boot file checking at you screen,press power botton to start boot from card,plug in your cable before start,wait for completed,soft reset you device,now ur device wake up again.
*** if want to boot win 6.1 new Rom,now you can follow previouse format that I already sended to you,any problem please reply to my mail please.Mika
I like to see ur device wake up again.
From : Eddie

Thank you again Eddie,
There was no file attached to your message.
I tried anyway with another ROM package, rename the nbh file to TRINIMG.nbh, copy it to an SD card formatted FAT with no label. I start the bootloader "Camera Button" + "Power button" + "Reset" button, but only get:
TRIN100
IPL-0.50
TRIN100
SPL-1.07.0000
Serial
Nothing about "loading" or "checking" ... :-/
When you said "boot from card" in your message, did you mean entering the bootloader as I did ?
Thank you for your help,
Mika

mikahtc2 said:
Thank you again Eddie,
There was no file attached to your message.
I tried anyway with another ROM package, rename the nbh file to TRINIMG.nbh, copy it to an SD card formatted FAT with no label. I start the bootloader "Camera Button" + "Power button" + "Reset" button, but only get:
TRIN100
IPL-0.50
TRIN100
SPL-1.07.0000
Serial
Nothing about "loading" or "checking" ... :-/
When you said "boot from card" in your message, did you mean entering the bootloader as I did ?
Thank you for your help,
Mika
Click to expand...
Click to collapse
Hi,Mika that I found that you format to FAT(Should format to FAT 32)just at the colume of FAT click down the arrow to select FAT 32 when u right hand click and look for format,and here is the Asia Original Rom I found
http://rapidshare.com/files/46816571...1_108_Ship.exe
Extract RUU.Signed.nbh rom file and rename it to TRINIMG.nbh,copy to Mini SD Card (Your Mini SD Card can not have any file in there,Except TRINIMG.nbh file only),on bootloader,plug in Charger and slot in ur card,screen will show u previousely what I'am show u press power/on-off botton and start untill step by step completed
Keep trying Mika
Good Luck
From : Eddie

mikahtc2 said:
Thank you again Eddie,
There was no file attached to your message.
I tried anyway with another ROM package, rename the nbh file to TRINIMG.nbh, copy it to an SD card formatted FAT with no label. I start the bootloader "Camera Button" + "Power button" + "Reset" button, but only get:
TRIN100
IPL-0.50
TRIN100
SPL-1.07.0000
Serial
Nothing about "loading" or "checking" ... :-/
When you said "boot from card" in your message, did you mean entering the bootloader as I did ?
Thank you for your help,
Mika
Click to expand...
Click to collapse
Your set is it ok
From : Eddie

to Mika
Hi Mika and all,
I have same problem as u, on my Trinity!
How was a solvent?
thanks for your answer

Related

Flashing WM6 - have I got this right?

Just got my Trinity today, and have successfully unlocked it using pof's unlocker. I unlocked the SIM lock and the CID lock, so it's now SuperCID.
I want to put WM6 on it, the LVSW version. I've downloaded the three files in the sticky post. Before I do it, I want to check that I'm understanding it right, because I'm a bit confused with version numbers.
So...
1) First, I need to HardSPL by running the "ROMUpdateUtility.exe" file from the Hard-SPL.zip file, yeah? I ran this (but didn't flash it) and was confused because the new "Image Version" was 1.20 whereas the Image Version shown in the "current image" bit was 1.24.xxx. Usually, going backwards is bad but I may be misunderstanding.
2) I then need to flash the Radio ROM to 1.41 - why do I need to do this? I guess I run the "ROMUpdateUtility.exe" from the GSM_xxx_xx file, right?
3) Finally, I need to flash WM6 - by running the "ROMUpdateUtility.exe" file from the WM6 zip.
Is that right?
Just tried to flash both the HardSPL and the Radio ROM, and the ROM Update Utility always craps out after I select "Yes" to the security prompt on the Trinity.
"ERROR 246 DEVICE NOT RESPONDING" is displayed in the update utility. Any ideas?
Also, if I go to the bootloader manually (holding down the buttons) the version numbers are:
TRIN100
IPL-0.50
TRIN100
SPL-1.07.0000
But when I let the ROM Update program enter the bootloader, these are shown instead:
TRIN100
IPL-SSPL by Des
TRIN100
SPL-1.07.ds
What does it all mean? Very confusing! It won't let it update anyway, when I select "Yes" to the security prompt, the screen goes black, the ROM updater throws up the error 246 and then the Trinity shows the bootloader.
GazChap said:
Just tried to flash both the HardSPL and the Radio ROM, and the ROM Update Utility always craps out after I select "Yes" to the security prompt on the Trinity.
"ERROR 246 DEVICE NOT RESPONDING" is displayed in the update utility. Any ideas?
Also, if I go to the bootloader manually (holding down the buttons) the version numbers are:
TRIN100
IPL-0.50
TRIN100
SPL-1.07.0000
But when I let the ROM Update program enter the bootloader, these are shown instead:
TRIN100
IPL-SSPL by Des
TRIN100
SPL-1.07.ds
What does it all mean? Very confusing! It won't let it update anyway, when I select "Yes" to the security prompt, the screen goes black, the ROM updater throws up the error 246 and then the Trinity shows the bootloader.
Click to expand...
Click to collapse
SPL by Des is a one time only SPL called SSPL-TRIN.exe, it's somewhere on this board. Sometimes it's baked into a ROM too ... it fakes the SPL.
HARD SPL stays on your phone .... doesn't need SPL by Des anymore.
Windows needs some time to switch from Windows CE to the bootlader driver. This can cause an error ...... just start the exe file again on the PC.
Another common flash error is with Vista, then you need to overwrite the default driver when you're in the bootloader. The driver is in "VistaRUU.zip"
Relaunch the Hard-SPL, then the radio ROM and after that LVSW or mUn's ROM.
There is a file you extract called EnterBootLoader.exe
I copy this to the Memory card.
Then before I run the update I run this on the memory card.
The phone goes to the boot loader and then once windows has re-detected it I run the update.
This seems to have eliminated all problems I've ever had flash updating.
akirainblack said:
There is a file you extract called EnterBootLoader.exe
I copy this to the Memory card.
Then before I run the update I run this on the memory card.
The phone goes to the boot loader and then once windows has re-detected it I run the update.
This seems to have eliminated all problems I've ever had flash updating.
Click to expand...
Click to collapse
I just tried this, but Windows doesn't seem to want to detect the presence of the device when I do. ActiveSync reports that nothing's connected.
Well I've got the Hard-SPL and Radio ROM to flash - instead of leaving ActiveSync connected I just went into the bootloader manually and did it that way.
But now I'm trying to flash WM6 and it gets up to 8% and then craps out with Error 286 - communication errors.
The device now won't boot past the bootloader
What do I do now?
Bloody hell. It's amazing, it really is.
I had it plugged into my USB hub.
Took it out and plugged it directly into the PC, just on the off-chance that the hub was screwed up.
It's all working fine now, I think!
Typical. Thanks for the assistance anyway guys.
Nps. Glad you got it sorted
Is the USB Hub powered? If not that will cause a ton of problems!
It's supposed to be powered, but I'm starting to think that the power supply might be faulty!
hi guys,
2 questions if i can;
1)What is HardSPL?
2) Why are there 3 steps to getting WM6? why can I not use the "ROMUpdateUtility.exe" file from the WM6 zip straight away?
Thanks a lot!!
Same Problem as GazChap
Hey All,
I was having the exact same problem as GazChap with the same configuration to start out with.
This is what I did:
1)plug in my p3600 to the USB
2)let synchronize, and hopefully finish, otherwise stop it
3)run HARD-SPL; this usually freezes after the first go and stalls in the bootloader
4)run HARD-SPL again; this time it will finish. You will have to turn on your machine again after this.
5)run AX3L ROM 2.0.8.2; this ALSO usually freezes after the first go and stalls in the bootloader
6)run the ROM again; This time its gonna work...
Now it works..
brick time
I loaded the hard spl succesfully. I could not get the radio upgrade to load no matter what I did. My instructions said it was optional, so I went directly to the WM6 rom exe load and it has a perpetual communications error after about 8% even though the WM6 loader says each time that recovery is successful. I have a tricolor screen (bootloader?) on my 3600 which won't respond to anything I have thought of yet. Anything I can do other than pitch it? Help! And thanks in advance.
ok, just want to make it short: (P3600 user)
1. I have WM6.1 ROM (FleNover 3.3 Black edition) installed.
2. When I want to downgrade to WM6 official, after 20% it goes error.
3. Now, it only shows 3 colors.
4. Here is my PDA information in 3 colors:
TRIN100
IPL-1.00
TRIN100 MFG
SPL-1.30.Olipro
5. When I want to upgrade with WM6 official, after my PDA shows the progress bar, it restarted and the update screen shows Error 286.
6. How do I fix it?
thank you very much

Completely stuck in bootloader!!!

My HTC 3600 is stuck in the bootloader. This afternoon I tried to flash to another Rom and after giving a connection error I was stuck in the bootloader.
I use Vista, so I followed some steps to install other drivers. I used Mtty to connect to my phone, I entered 'set 14 0' and 'task 8' or task 0. My phone restarts but only to return again to the bootloader.
I tried to reflash. I see the progress bar on my screen and on my phone, but after about a minute it reports an error.
I have already disabled 'usb-connections' in the Windows Mobile Device manager.
I have removed my sim and sd-card. I have removed my battery and waited an hour...
I tried 'UniExitBootloader.exe' which runs correctly telling me my problems are over, only to see my phone restart again into the bootloader.
Summarizing, I'm a bit hopeless!!!
My bootloader displays the following information:
TRIN100
IPL-0.50
TRIN100
SPL-9.99.CP
And at the bottom: USB
If there is anybody who can help... please do!!!
Regards,
theDjave
TheDjave said:
My HTC 3600 is stuck in the bootloader. This afternoon I tried to flash to another Rom and after giving a connection error I was stuck in the bootloader.
I use Vista, so I followed some steps to install other drivers. I used Mtty to connect to my phone, I entered 'set 14 0' and 'task 8' or task 0. My phone restarts but only to return again to the bootloader.
I tried to reflash. I see the progress bar on my screen and on my phone, but after about a minute it reports an error.
I have already disabled 'usb-connections' in the Windows Mobile Device manager.
I have removed my sim and sd-card. I have removed my battery and waited an hour...
I tried 'UniExitBootloader.exe' which runs correctly telling me my problems are over, only to see my phone restart again into the bootloader.
Summarizing, I'm a bit hopeless!!!
My bootloader displays the following information:
TRIN100
IPL-0.50
TRIN100
SPL-9.99.CP
And at the bottom: USB
If there is anybody who can help... please do!!!
Regards,
theDjave
Click to expand...
Click to collapse
First, read the Guides.
Try reflashing it.
If no joy, try the SD Card method, from what I see, you have HardSPL installed.
If still no joy, try flashing one of the original WM5.
And if it's still no joy, take a look here.
Thanks!
Thanks, your last option saved my day. After running unbrick.bat the problem was solved!
Thx again!!!
Regards,
TheDjave

Problem with flashing a new ROM

I’ve a problem with the ROMUpdateUtility.exe, when I follow these instructions:
-Enter bootloader (rainbowscreen)
-Connect to pc (activesync)
-Run the ROMUpdateUtility.exe and follow onscreen instructions
After the process bar appears on the screen of my pc, it also appears on my x1, but it stuck on 0%
And after that appears on the RUU.exe the Error message [262] Update Error .
I`m very frustrated, because I tried it all day, but it doesn't work.
Maybe you can help me………
http://forum.xda-developers.com/showthread.php?t=431218
Hardspl,
Regards,
WC
got the same problem, allready got hard-spl but allwways get error 262. only when i flash with an original rom it works. with a custom rom allways error 262. flashing a custom rom with the sd card method also doesnt work. anyone got any ideas how to solve this?
- Download and install .NET Framework 3.5 SP1
- If you are using Vista, install the Mobile Device Center 6.1
- Set up the ActiveSync (XP) / Mobile Device Center (Vista) connection with your X1
- Charge the battery to at least 50% or more
- (Re)Connect the X1
- Run X1_HardSPL.exe
- Follow the instructions (it should say something like "Image Version: 1.02.111.7" to "1.00.X1")
- If asked, press "Yes" on the X1
- Now a 4-color screen should show up, showing some version Info
- After that, a progressbar screen will be shown and the phone will reboot when finished
- Click "Finish" on the PC
- If you want to check if everything went fine, turn the device off (long power button press), then hold the "volume down" button and turn the device on again, still holding the "volume down" button until the 4-color screen shows up. It should read something like:
KOVS110
SPL-0.72.OliNex
MicroP1-787
MicroP2-707
- Remove and reinsert the battery to exit bootloader mode
this is in http://forum.xda-developers.com/showthread.php?t=446070
SiRIus[X] said:
- Download and install .NET Framework 3.5 SP1
- If you are using Vista, install the Mobile Device Center 6.1
- Set up the ActiveSync (XP) / Mobile Device Center (Vista) connection with your X1
- Charge the battery to at least 50% or more
- (Re)Connect the X1
- Run X1_HardSPL.exe
- Follow the instructions (it should say something like "Image Version: 1.02.111.7" to "1.00.X1")
- If asked, press "Yes" on the X1
- Now a 4-color screen should show up, showing some version Info
- After that, a progressbar screen will be shown and the phone will reboot when finished
- Click "Finish" on the PC
- If you want to check if everything went fine, turn the device off (long power button press), then hold the "volume down" button and turn the device on again, still holding the "volume down" button until the 4-color screen shows up. It should read something like:
KOVS110
SPL-0.72.OliNex
MicroP1-787
MicroP2-707
- Remove and reinsert the battery to exit bootloader mode
this is in http://forum.xda-developers.com/showthread.php?t=446070
Click to expand...
Click to collapse
i always did it like this, but it doesn't work,
the process bar always stuck at 0%
when i enter bootloader, it says
KOVS110
SPL-0.78.0000
MicroP1-787
MicroP2-707
i've solved my problem by reinstalling active sync, after that i could reinstall hard-spl and then i could flash a custom rom
i've solved my problem by reinstalling active sync, after that i could reinstall hard-spl and then i could flash a custom rom
Click to expand...
Click to collapse
doesn't work
if this is what your bootloader is saying the device is NOT hardspl'd and needs to be in order to flash a custom rom as per the link I posted.
As posted above your bootloader should look similar to this:
KOVS110
SPL-0.72.OliNex
MicroP1-787
MicroP2-707
Regards,
WC
ph07242 said:
when i enter bootloader, it says
KOVS110
SPL-0.78.0000
MicroP1-787
MicroP2-707
Click to expand...
Click to collapse
Wild Child said:
if this is what your bootloader is saying the device is NOT hardspl'd and needs to be in order to flash a custom rom as per the link I posted.
As posted above your bootloader should look similar to this:
KOVS110
SPL-0.72.OliNex
MicroP1-787
MicroP2-707
Regards,
WC
Click to expand...
Click to collapse
still the same problem [262] Update Error

[SOLVED] Touch HD is dead???

Hi all!
first of all sorry for my Egnlish
I tried to perform task29 on my HD and get an error "Invalid vender ID", in some guides i read that in this case I should use a stock .nbh files... I tried the .hbn file from HSPL thread from one of restore_stock_spl* zip files. task29 was performed normally. When I turn on device I can see the clear smart mobility screen only with "smart mobility" words in center. bootloader now showing me 1.54 Olinex version. Before task29 this version was 1.56.
And from this moment I can't do anything with device: I can't flash any rom or radio. When using RUU after three-colour screen device shows me a progres indicator which suspends on 0% and RUU progress is also 0%. after waiting some time RUU shows an "262 Update erorr". When I'm trying to flash ROM or radio from SD card I see the three-colour screen then grey screen "loading... No image file!!!" and then again the three-colour screen. It shows so fast that it looks like a screen blinking and almost impossible to read what is written on grey screen.
I have spend 3 days while looking for different files and flash packages, have read a guides and I'm at a loss.
Please helpme to make my HD work again!
sergey.ss said:
Hi all!
first of all sorry for my Egnlish
I tried to perform task29 on my HD and get an error "Invalid vender ID", in some guides i read that in this case I should use a stock .nbh files... I tried the .hbn file from HSPL thread from one of restore_stock_spl* zip files. task29 was performed normally. When I turn on device I can see the clear smart mobility screen only with "smart mobility" words in center. bootloader now showing me 1.54 Olinex version. Before task29 this version was 1.56.
And from this moment I can't do anything with device: I can't flash any rom or radio. When using RUU after three-colour screen device shows me a progres indicator which suspends on 0% and RUU progress is also 0%. after waiting some time RUU shows an "262 Update erorr". When I'm trying to flash ROM or radio from SD card I see the three-colour screen then grey screen "loading... No image file!!!" and then again the three-colour screen. It shows so fast that it looks like a screen blinking and almost impossible to read what is written on grey screen.
I have spend 3 days while looking for different files and flash packages, have read a guides and I'm at a loss.
Please helpme to make my HD work again!
Click to expand...
Click to collapse
Have you tried flashing stock rom which came with your device?
I have tried .nbh file from "HTC Stock ROM_BLACKSTONE_1.14.401.3 (22273) WWE.zip"
if it possible tell me what exactly should I download and how to use it, I'll try. I'll try everything you advise, because I didn't find solution myself and don't know what esle should I try. first of all where should I start? do I need to perform task29 correctly or do I need to restore HSPL to 1.56 version, or flash a stock rom?
* Dont connect your phone to your computer.
* Hold down the Volume down button and hit the power button.
* Your entering the tricolor boot screen and at the bottom the word "Serial".
* Now connect you phone to your computer with te USB cable the word serial disappear and now it says USB.
* Now you can normally flash/update your phone and please use hspl.
I had before a HTC Diamond. On that device I used to run "task29" until that command killed my device. Almost same as you, I could flash the device but I couldn't boot normally. My ROM memory probably got damaged for good so I had to replace the device with a new one. My suggestion to you: on a new device never use that command again and you will be fine.
iamjohno said:
* Dont connect your phone to your computer.
* Hold down the Volume down button and hit the power button.
* Your entering the tricolor boot screen and at the bottom the word "Serial".
* Now connect you phone to your computer with te USB cable the word serial disappear and now it says USB.
* Now you can normally flash/update your phone and please use hspl.
Click to expand...
Click to collapse
I tried this way. Progress is suspends on 0% and then I get an error "262 Update Error" in RUU What should I do first: change HSPL version or flash ROM/radio?
xdmcdmc said:
I had before a HTC Diamond. On that device I used to run "task29" until that command killed my device. Almost same as you, I could flash the device but I couldn't boot normally. My ROM memory probably got damaged for good so I had to replace the device with a new one. My suggestion to you: on a new device never use that command again and you will be fine.
Click to expand...
Click to collapse
it's terrible, hope my devise still alive...
There is one detail I didn't mentioned... If download task29 package and just simply execute task29.exe (using .nbh from this package) progress on device goes forward to 4% and then "Invalid vender ID" error occurs... So I think I should use another .nbh file but which one?. Hope this checking of vender ID is not that 4% of progress and some actions with device memory really starts...
sergey.ss said:
I tried this way. Progress is suspends on 0% and then I get an error "262 Update Error" in RUU What should I do first: change HSPL version or flash ROM/radio?
it's terrible, hope my devise still alive...
There is one detail I didn't mentioned... If download task29 package and just simply execute task29.exe (using .nbh from this package) progress on device goes forward to 4% and then "Invalid vender ID" error occurs... So I think I should use another .nbh file but which one?. Hope this checking of vender ID is not that 4% of progress and some actions with device memory really starts...
Click to expand...
Click to collapse
Try using a radio nbh for blackstone.
The original package, contains nbh for the LEO
thanks all of you for replay but I still need a help very much.
there are ways that I have tried
1. flashing rom/radio from SD card
2. flashing rom/radio using RUU
3. task29 using different .nbh files
4. install/restore HSPL
In the first way always hapens same thig: I turn off the device, turn it on, press volume down button, see tricolor bootloader screen, then for a very short time (less than second) i see a grey screen and there is written: "loading... No image file!!!", then i see tricolor bootloader again.
I tried different rom/radio files (it was "HTC Stock ROM_BLACKSTONE_1.14.401.3 (22273) WWE" and other roms I flashed before and different versions of radio files from thread int this forum).
for the RUU using ways I always get two situations: I turn off the device, turn it on, press volume down button, see tricolor bootloader screen, connect the devise to PC, execute RUU/taks29/HSPL/Restore_SPL, then press next a few times, then i see the progress in RUU and on device screen and there is two endings:
1. progress goes up to 4% and devise making a soft reset, load the black smart mobility screen with no orange version characters on screen bottom, RUU shows "Invalid vender ID";
2. progress suspends on 0% and after some timeout RUU shows "Error [262] Update error" and now changes on device screen.
last what I have tried: execute task29 with last hd radio 1.17.25.09 file and got invalid vendor id error, then execute task29 with radio 1.09.25.14 file and got update error.
my be this holds some information: in my bootloader is written following
BLAC100 32M
SPL-1.54.0000
MicroP-BlackStone (LED) v6
what should I do?
sergey.ss said:
thanks all of you for replay but I still need a help very much.
there are ways that I have tried
1. flashing rom/radio from SD card
2. flashing rom/radio using RUU
3. task29 using different .nbh files
4. install/restore HSPL
In the first way always hapens same thig: I turn off the device, turn it on, press volume down button, see tricolor bootloader screen, then for a very short time (less than second) i see a grey screen and there is written: "loading... No image file!!!", then i see tricolor bootloader again.
I tried different rom/radio files (it was "HTC Stock ROM_BLACKSTONE_1.14.401.3 (22273) WWE" and other roms I flashed before and different versions of radio files from thread int this forum).
for the RUU using ways I always get two situations: I turn off the device, turn it on, press volume down button, see tricolor bootloader screen, connect the devise to PC, execute RUU/taks29/HSPL/Restore_SPL, then press next a few times, then i see the progress in RUU and on device screen and there is two endings:
1. progress goes up to 4% and devise making a soft reset, load the black smart mobility screen with no orange version characters on screen bottom, RUU shows "Invalid vender ID";
2. progress suspends on 0% and after some timeout RUU shows "Error [262] Update error" and now changes on device screen.
last what I have tried: execute task29 with last hd radio 1.17.25.09 file and got invalid vendor id error, then execute task29 with radio 1.09.25.14 file and got update error.
my be this holds some information: in my bootloader is written following
BLAC100 32M
SPL-1.54.0000
MicroP-BlackStone (LED) v6
what should I do?
Click to expand...
Click to collapse
Hmmm... I want to know, what .nbh file did you include in the task29 folder you have? Remember, you must to copy a radio ROM to your task29 folder and name it as RUU_signed.nbh, don't copy an OS ROM to task29 as this will give problem.
From the information above, seems you had restore to original SPL? Try flash HSPL or USPL. If you have any problem flashing, you can ask in this thread http://forum.xda-developers.com/showthread.php?t=505377
Good luck, my friend. Cheers.
Agree with philrom: you are an the stock SPL. So, flash HSPL, then you should be fine.
Has this been resolved?
Fallen Spartan said:
Has this been resolved?
Click to expand...
Click to collapse
Yes. Sorry I forgot to post the ending of this story...
I didn't understood about flashing HSPL in formated device... I was really tired of using different ways and flashing different roms... I just took my device to a not official service center (there is no Touch HD for my country). There guys said me that I need to flash a stock rom of my HD birthplace country. They found out that it was shipped from Arab Emirates, than they found a required ROM and flash it. It cost me 50$. Now I'm using my HD as usual.
Thank for the replays!!!
Glad you got it resolved
Thread closed

[Q] Help Required regarding installing new ROM !!!

I am having Xperia X1 Black with factory installed Win Mo 6.1....so, now i wanted to try the Windows Mobile 6.5.3-Build- 29007. Can anyone help me with detailed procedure of installing new ROM on my X1.
I tried according to the procedure available in various post's. According to the procedure i need to first Hard SPL my phone. So, when i try doing that my progrees bar on the phone screen gets stuck at 0% and then i get a error that check the connection of the pc and phone.
In bootloader mode the configuration shown is as follows
KOVS110
SPL-0.78.0000
Micro P1-787
Micro P2-707
I even tried the direct SD card method in which i renamed the ROM file i.e RUU_signed.nbh to kovsimg.nbh...in this when i go to the bootloader mode, the tricolour screen shows with above mentioned specifications then after about few seconds another screen is displayed saying" LOADING..." and then gets stuck.
So, anybody can please help me with installing new ROM
Regards
Bhavik
guitarguru31 said:
I am having Xperia X1 Black with factory installed Win Mo 6.1....so, now i wanted to try the Windows Mobile 6.5.3-Build- 29007. Can anyone help me with detailed procedure of installing new ROM on my X1.
I tried according to the procedure available in various post's. According to the procedure i need to first Hard SPL my phone. So, when i try doing that my progrees bar on the phone screen gets stuck at 0% and then i get a error that check the connection of the pc and phone.
In bootloader mode the configuration shown is as follows
KOVS110
SPL-0.78.0000
Micro P1-787
Micro P2-707
I even tried the direct SD card method in which i renamed the ROM file i.e RUU_signed.nbh to kovsimg.nbh...in this when i go to the bootloader mode, the tricolour screen shows with above mentioned specifications then after about few seconds another screen is displayed saying" LOADING..." and then gets stuck.
So, anybody can please help me with installing new ROM
Regards
Bhavik
Click to expand...
Click to collapse
You bootloader should show
Kovs110
SPL-0.78.OliNex
MicroP1-787
MicroP2-707
don't know if .0000 and OliNex is different
http://forum.xda-developers.com/showthread.php?t=431218
look here for download the good Hard SPL and then replace the 0.78 in it, HARD SPL with cable / computer (I never use SD CARD because it never works for me)
then you TASK29 (find it in the forum), then you can flash it =)

Categories

Resources