Related
I have looked everywhere but no luck! Can someone please give clear instruction how to replace the digitizer/touch panel?
I have only found instructions how to disassemble the diamond up to the LCD stage only! But after that it does not show how to take the LCD out of the housing to expose the Digitizer.
Hope someone knows how to do it.
Thanks.
The instructions you looked at, where they from the Service Manual or another source?
one from the service manual at XDA-WiKi page and other post from http://www.pdacenter.ru/razborka/razbor-htc-touch-diamond
but both goes up to the same stage and stop.
Yeh I've got the same service manual and it doesn't really go into any detail about how to replace the digitizer. Maybe there's another 'level' of the Service Manual for that. Only question is, where does one obtain it? Good luck replacing it - how come you're replacing it btw? Your touch screen not responding?
Digitizers (touch screen) usually are not being replaced at all. The LCD screen (with digitizer) is the one block. And it is being changed completely in service centers.
But: If you can find just digitizer, then you may cut off with office knife the digitizer from the lcd-screen itself (on borders only, do not cut your screen) and then place the new digitizer on the screen firmly (it will stick to it on borders).
I've done it with my treo 750 yesterday.
kortez said:
Digitizers (touch screen) usually are not being replaced at all. The LCD screen (with digitizer) is the one block. And it is being changed completely in service centers.
But: If you can find just digitizer, then you may cut off with office knife the digitizer from the lcd-screen itself (on borders only, do not cut your screen) and then place the new digitizer on the screen firmly (it will stick to it on borders).
I've done it with my treo 750 yesterday.
Click to expand...
Click to collapse
Thanks for your input. Digitizers for Diamond are available for sale separately.
just to make sure i got this right, if it is only fixed on LCD by sticking to it without any screws can i pry it out from the front side without disassembling the diamond?
Scratched screen
Ok, So I finnaly scratched the screen. Quite badly, must add !!
I was wondering the costs to replace the screen. Do I need a whole case / digitizer or lcd ?
Also what would the costs be roughly, as I am unable to contact my local repair shop....
dalewinterstein said:
Ok, So I finnaly scratched the screen. Quite badly, must add !!
I was wondering the costs to replace the screen. Do I need a whole case / digitizer or lcd ?
Also what would the costs be roughly, as I am unable to contact my local repair shop....
Click to expand...
Click to collapse
digitizer arround 29 USD + shipping.
not sure if LCD is available yet.
if you scratched the screen you will only need to replace the digitizer which is the actual screen you press on.
the only thing is no clear instruction how to replace it!
ammar said:
Thanks for your input. Digitizers for Diamond are available for sale separately.
just to make sure i got this right, if it is only fixed on LCD by sticking to it without any screws can i pry it out from the front side without disassembling the diamond?
Click to expand...
Click to collapse
Without disassembling - no, for sure.
And seeing the video - I would not suggest you to, it's quite hard, cuz it's all packed very tight.
I heard that there's glass in front of screen on diamond that sends the pressures to the real touch screen. But that maybe not true. I guess you'll have to disassemble the diamond to see what the touchscreen is on it.
Or you shoudl find the video, where you can clearly see if the touch diamond' screen have any protective glass..
Kortez,
thanks for your help, do you have link to the said video?
thanks
can't remember where I've seen. But it exists.
http://www.youtube.com/watch?v=_jY46M_NGz0
Check ou this web site
http://www.dealextreme.com/
it has very replacement parts and with a very good price, and free shipping!!!
I've just recived my tytn II digitizer for only 4,99.
Hope it helps.
tape said:
Check ou this web site
http://www.dealextreme.com/
it has very replacement parts and with a very good price, and free shipping!!!
I've just recived my tytn II digitizer for only 4,99.
Hope it helps.
Click to expand...
Click to collapse
We need the instruction on the replacement step, not the part.
I've just replaced the digitizer now on my Diamond...having issues getting it back together though, will go into it in a minute.
Originally I ordered only a digitizer, then dismantled the phone and hit a brick wall when I tried getting the screen from the metal fascia, the adesive is really strong, I actually ended up cracking the screen under the digitizer and so ended up having to buy a screen with a digitizer for £10 more - to be honest I recommend this is what you do - if you order just a digitizer then you have to mess about soldering the cable onto the cable of the screen (as well as getting the broken digitizer off the screen and probably cracking it in the process)
Anyway, my new one came today, managed to put it onto the fascia fine and have started putting the thing back together, but I cant connect the 2 cables to the mainboard part! cos for a start theyre underneath and not long at all! anyone have any ideas?
Adam86 said:
I've just replaced the digitizer now on my Diamond...having issues getting it back together though, will go into it in a minute.
Originally I ordered only a digitizer, then dismantled the phone and hit a brick wall when I tried getting the screen from the metal fascia, the adesive is really strong, I actually ended up cracking the screen under the digitizer and so ended up having to buy a screen with a digitizer for £10 more - to be honest I recommend this is what you do - if you order just a digitizer then you have to mess about soldering the cable onto the cable of the screen (as well as getting the broken digitizer off the screen and probably cracking it in the process)
Anyway, my new one came today, managed to put it onto the fascia fine and have started putting the thing back together, but I cant connect the 2 cables to the mainboard part! cos for a start theyre underneath and not long at all! anyone have any ideas?
Click to expand...
Click to collapse
I thought the digitizer cable can be just slot into the connector type, no? Did your digitizer come with soft ply tools? which to help on plying out the screen and digitizer i heard. I'm gathering info before placing my purchase on the digitizer... Coz its badly scratches, felt and kicked!
No unfortunately not - you have to solder it on theres some contacts for it.
I managed to get all mine back together you just have to take your time and be really careful - it works perfectly now. I'm really chuffed as its a really good spare to have
If I was you i'd order a screan and a digiziser together cause then it will just be a case of pulling the screen off the adesive on the fascia (it's stuck really well you might even crack your broken one like I did) and then stick the replacement on and reassemble!
Hi, could anyone of you make some pictures or a small video about how to get the display out of the body, or where exactly i need to pull the display out.
i have already dismantled my diamond, but still didnt get the display and digitizer out. When i pulled the display i think i broke it somehow, because now my display shows me only stripes...
anyway, my ordered display still didnt arrive....
if you could make a vid or some pictures, it would be very helpful.
Adam86 said:
No unfortunately not - you have to solder it on theres some contacts for it.
I managed to get all mine back together you just have to take your time and be really careful - it works perfectly now. I'm really chuffed as its a really good spare to have
If I was you i'd order a screan and a digiziser together cause then it will just be a case of pulling the screen off the adesive on the fascia (it's stuck really well you might even crack your broken one like I did) and then stick the replacement on and reassemble!
Click to expand...
Click to collapse
how was the soldering part? difficult? as i heard it might melt the plastic cable, no?
If i do cracked the existing digitizer, no harm i see since its already borken though.
Well, i managed to get the lcd and tocuh sceen apart, and now am stuck with the soldering part either.
the sceen has to be pushed out from the inside....the glue they used is pretty strong. and the display breaks pretty fast....
isnt there a way to connect the lcd and ts without soldering?
I'm assuming I smashed my At&t tilt or something, there is no cracks on the screen or anything, but the pic below shows the display I get. I'll have the phone for about a year in about 2 weeks. Anyone have an idea as to how much At&t or HTC will charge to fix this or am I better off buying a new phone? Or any ideas as to what could be broken and how it can be fixed? It doesn't allow me to do a hard reset. Thanks
well i don't know if warranty will cover it or not but you are still under your one year warranty so you could try to get a replacement. Its hard to say what could be causing it. You can check out mike channon's articles on disassembling a kaiser.
Good luck.
brianlb said:
I'm assuming I smashed my At&t tilt or something, there is no cracks on the screen or anything, but the pic below shows the display I get. I'll have the phone for about a year in about 2 weeks. Anyone have an idea as to how much At&t or HTC will charge to fix this or am I better off buying a new phone? Or any ideas as to what could be broken and how it can be fixed? It doesn't allow me to do a hard reset. Thanks
Click to expand...
Click to collapse
Well to my trained eye, it looks as though you have actually cracked the lcd screen. This damage isnt generally covered by any manufacturers standard warranty. Unless you purchased an extra warranty including accidental damage, I think its up to you to repair yourself unless you want to spend 400USD + for the repair. Taking it apart isnt terribly difficult and I have seen links to lcd screens posted all over for no more than 100USD. Check Ebay also.
http://cgi.ebay.com/LCD-Replacemet-...39:1|66:2|65:12|240:1318&_trksid=p3286.c0.m14
Here is one for 45 USD
Hope this helps ya
pyraxiate said:
Well to my trained eye, it looks as though you have actually cracked the lcd screen. This damage isnt generally covered by any manufacturers standard warranty. Unless you purchased an extra warranty including accidental damage, I think its up to you to repair yourself unless you want to spend 400USD + for the repair. Taking it apart isnt terribly difficult and I have seen links to lcd screens posted all over for no more than 100USD. Check Ebay also.
http://cgi.ebay.com/LCD-Replacemet-...39:1|66:2|65:12|240:1318&_trksid=p3286.c0.m14
Here is one for 45 USD
Hope this helps ya
Click to expand...
Click to collapse
I don't see a crack in the screen. Can there still be a crack in it that isn't visible or not noticeable until you take it apart? If that's the case I'll either buy a new screen or just buy a new phone on ebay for 200bux. Also anyone have any recommended sites on how to replace the screen?
This raises a great question for me. i work in a clean room/static sensative environment and repair and calibrate many different types of electronics (mostly signal generators & spectrum analyzers). I was wondering if anyone here has actually attempted to replace a LCD screen with success. And if so, how complicated the process was. I have downloaded the schematical drawings and have found replacement parts for the kaiser online for extremely cheap. i will post the site as soon as i find it again.
I did a screen replacement on a Wizard, and it wasn't that difficult. just make sure you don't break anything while trying to pry small pieces off to get to the screen.
Stu_Can_Sam said:
This raises a great question for me. i work in a clean room/static sensative environment and repair and calibrate many different types of electronics (mostly signal generators & spectrum analyzers). I was wondering if anyone here has actually attempted to replace a LCD screen with success. And if so, how complicated the process was. I have downloaded the schematical drawings and have found replacement parts for the kaiser online for extremely cheap. i will post the site as soon as i find it again.
Click to expand...
Click to collapse
ITs easy as hell.
I've done it two times with success.
Its only matter of two connection belts and thats all at all .
Screen replacement is really easy here.
brianlb said:
I don't see a crack in the screen. Can there still be a crack in it that isn't visible or not noticeable until you take it apart? If that's the case I'll either buy a new screen or just buy a new phone on ebay for 200bux. Also anyone have any recommended sites on how to replace the screen?
Click to expand...
Click to collapse
Generally you will NOT see a physical crack on the surface. The surface is actually JUST a digitizer ( a separate piece which is built into or ontop of your LCD for input purposes ). The digitizer is basically your touch screen portion of the LCD. What is actually cracked is the thin film below that which contains all of the liquid crystals.
As far as the replacement goes, I believe it is Michael Channon who has the step by step instructions on how to disassemble and replace the LCD. It isnt a hard task from what I can tell. I had taken my hermes ( Tytan ) apart so many times that i could do it in my sleep. Its not a terribly difficult process.
Here is Michaels Guide
Its not in English but its not hard to follow the pictures. He has done a great job at documenting the procedure.
If you are a bit scared to try it yourself, have a geeky friend do it for you ( maybe get him a date to a movie or something lol )
It should only cost you no more than 50$USD to repair ( Minus the bribe for a date lol )
Hope this helps you out !
pyraxiate said:
Generally you will NOT see a physical crack on the surface. The surface is actually JUST a digitizer ( a separate piece which is built into or ontop of your LCD for input purposes ). The digitizer is basically your touch screen portion of the LCD. What is actually cracked is the thin film below that which contains all of the liquid crystals.
As far as the replacement goes, I believe it is Michael Channon who has the step by step instructions on how to disassemble and replace the LCD. It isnt a hard task from what I can tell. I had taken my hermes ( Tytan ) apart so many times that i could do it in my sleep. Its not a terribly difficult process.
Here is Michaels Guide
Its not in English but its not hard to follow the pictures. He has done a great job at documenting the procedure.
If you are a bit scared to try it yourself, have a geeky friend do it for you ( maybe get him a date to a movie or something lol )
It should only cost you no more than 50$USD to repair ( Minus the bribe for a date lol )
Hope this helps you out !
Click to expand...
Click to collapse
Thx, I'm gonna give it a shot. I went ahead and bought the screen off ebay from the post by pyraxiate. Worst case I mess it up and buy a new phone of ebay for 150-200, which is what I originally thought I'd have to do, so this at least gives me a chance to save some $$$
brianlb said:
Thx, I'm gonna give it a shot. I went ahead and bought the screen off ebay from the post by pyraxiate. Worst case I mess it up and buy a new phone of ebay for 150-200, which is what I originally thought I'd have to do, so this at least gives me a chance to save some $$$
Click to expand...
Click to collapse
Let us know how it goes
Glad I could help
Got it all done, actually my pops did it. Works great, he took it apart just like the Mike Channon pics show, don't know if you had to do all of it or not just to replace the screen, but he did. Only one little annoying thing now that it's back together is that a small part of the black plastic out case hangs out just a tab and isn't flush, which makes it a little annoying when hitting the power/standby button on the right side of the phone. But I can learn to live with that I think. thanks for all the help.
congratulations!
good to hear you've achieved a successful repair!
correct me if i'm wrong...are you saying that the two halves of the phone (screen and keyboard) don't align properly when the keyboard is closed? if so, i remember a thread in this section of the kaiser forums that details (with pictures) how to possibly fix that particular problem!!!
"search and ye shall foundeth it !!!"
brianlb said:
Got it all done, actually my pops did it. Works great, he took it apart just like the Mike Channon pics show, don't know if you had to do all of it or not just to replace the screen, but he did. Only one little annoying thing now that it's back together is that a small part of the black plastic out case hangs out just a tab and isn't flush, which makes it a little annoying when hitting the power/standby button on the right side of the phone. But I can learn to live with that I think. thanks for all the help.
Click to expand...
Click to collapse
Im glad i could help Im also glad to hear the phone is up and running again
As was stated before, there is a thread for the case not aligning. I did some quick looking but to no avail. If i come across it ill be sure to post it
I'm not sure if I'm explaining it correctly. But it's basically the outer case, and around the power button it's not flush. Not sure if you can tell from my pics. I tried also doing a search w/no luck. I'm sure there is some specific name or something other than case that it's under.
When i replaced my faceplate i had the same problem. all i did was push it in...kinda hard, and it poped in, or you could use a plasic flathead and pop it back in...
DemoShadow said:
When i replaced my faceplate i had the same problem. all i did was push it in...kinda hard, and it poped in, or you could use a plasic flathead and pop it back in...
Click to expand...
Click to collapse
I tried that, and it doesn't seem to pop in at all.
I think its just like DemoShadow said. I dropped mine once and it seems to be a similar issue. I also just pushed really hard to get it to pop back in. I think its just that clip isnt in place as it should be when it was put back together. If anything, try to take it apart and put it back together
kristoff_sz said:
ITs easy as hell.
I've done it two times with success.
Its only matter of two connection belts and thats all at all .
Screen replacement is really easy here.
Click to expand...
Click to collapse
how did you put the keyboard back on????????????????
Can you be more specific?
Hey,
I literally just replaced the screen on my backup Tilt last night. Still got most of it in my head.
What, exactly, do you mean about putting the keyboard back on? Got any pics of where you are now?
This was one of the easiest things I've had to do...asside from it being somewhat tedious. Most of my issues were resolved by MAGNIFICATION! Once I could see what I was doing, there were almost no issues.
I only paid $31.99 on eBay for a screen with free shipping (from USA no less)...less than the $35 I would have had to pay with the insurance through my Provider Dealer...and I didn't have to wait for 3-5 weeks to get it back.
I'd do this for people with broken screens as a service, but I can't guarantee the cost of the screen...it goes up and down too much.
If you can be real descriptive, or have pictures, I'm pretty sure I can help get you back together.
Let me know, I'll keep an eye on this thread...
RAF
here's some dismantling guides
http://www.mikechannon.net/page1.html
you dont have to remove the keyboard to replace the LCD, unless u're talking about the outer keypad, which just sits in its spot
My touch screen stopped working on my phone, but the screen is still visible. I'm assuming it's the digitizer. I was wondering if anybody has done or tried replacing only the digitizer. Does this work, is it better just to replace both? Any suggestions? Thanks.
Save yourself the headache
Just replace the complete screen unit (lcd + digitizer).
The digitizer is held on the screen with some super strong adhesive that is nearly impossible to get off cleanly. Also, there are three (4?) thin ribbon tabs that have to be soldered to the board on the rear of the lcd. Unless you are really confident with a soldering iron, it is extremely hard to do.
I replaced my screen unit in about a half hour. Make sure you go to the wiki and find one of the excellent disassembly guides before you start.
Thanks
Thanks, that's exactly the information i needed to know. I found the fon logix video. Is it only a t6 tool i need, or do i also need a t5. I have seen conflicting info on this? Thanks again.
I got my scren unit from ebay, and it included a torx driver and a plastic case tool. I honestly can't remember what size came in the kit, because I used my own torx set. Im pretty sure its just the one size, though.
Good luck!
You might find this information interesting.
http://forums.wireless.att.com/cng/board/message?board.id=cingular&thread.id=116836
Disregard ............
i always replace only the touch screen. okay i've done it aprox 30 times. But i never broke one.
if you decide to replace only the touchscreen, there are 2 types. thus check which on you have, and i found out that sometimes reassamble, and cleaning can help.
good luck.
torx is 5 and 6, 6 for opening the back of the phone, 5 for the screen part removal of the body and opening it. you need an opening tool!!
adhesive
is there a terrible adhesive between the screen and digitizer, as the second poster mentioned? how difficult is it to deal with?
just cut away with snapoff knives. It wil break in more pieses. (the glas that is) just be carefull, and take your time
Thanks
Thanks for all of the info, i went ahead and purchased the screen with the digitizer and tools. One thing i have noticed though is the d-pad has stopped working also, i'm using a custom rom so i'm not sure if it's just that or it's something else. i will prob re-image after i replace screen.
Abel2007 said:
just cut away with snapoff knives. It wil break in more pieses. (the glas that is) just be carefull, and take your time
Click to expand...
Click to collapse
Well, guess I was a smarty pants and bought my stuff before consulting XDA...as such, I ONLY bought the touchscreen rather than the entire new unit. Cheaper, yes, but I had no idea about the adhesive until just now. My only question is, once I remove the old screen from the LCD with a razor blade, how do I affix the new one?
Anyone?
i would love to know this too because i have to also replace my digitizer!
drokkon said:
Well, guess I was a smarty pants and bought my stuff before consulting XDA...as such, I ONLY bought the touchscreen rather than the entire new unit. Cheaper, yes, but I had no idea about the adhesive until just now. My only question is, once I remove the old screen from the LCD with a razor blade, how do I affix the new one?
Anyone?
Click to expand...
Click to collapse
I used rtv gasket maker the transparent blue one worked well.
you can find it in automotive section. Actually any silcone will work.
also can use double sided tape but needs to be very thin
I've already changing my digitizer, but it doesn't seem to work. So I've change the whole part. cost me $20 more on ebay.
my advice is to change the whole package with the lcd too.
Hi,
Last night I knocked a small table and my girlfriends phone and a remote for the TV fell off.
We noticed that her phone now has a ring of black dots on the screen, mostly visible with a white background (E.G websites) but also from the home screen and the like.
We think she's cancelled her phone insurance, as she's never had a payment out to the company.
Can anyone tell me if its a Digitizer (What is one of these? Is it just the touch screen sensitive part of the phone?) Or the actual LCD Screen itself?
If you click on the photo it will load a larger image
Thanks for any assistance, kinda annoyed about this and wondering if I can repair myself with the parts on ebay. Or does anyone know how much HTC Charge to repair similar? Either in $USD, £GBP or €Eur, I can convert and get a ball park figure.
Hi
First of all is the phone still in warranty? If so take it back to an HTC dealer they should repair it for you for free. TD2 screens are not very good and it's a common fault. ( i had to have mine repaired after just only 3 weeks! )
The TD2 screen is made out of 2 parts, The touch screen or the 'digitizer' as you call it and a normal LCD screen underneath. You need to establish which has gone faulty.
If the touch screen still operates normally i.e the screen does not lock up or freeze and allows you to navigate normally then its the lcd screen below. If the touch screen is faulty one good way of checking is to put a piece of tape over the damaged area and try to lift it up a little to see if the marks / dots disappear and functionality can temporarily be restored.
Its hard to tell from your picture which it is..... sorry
I'm not sure how much a replacement by a dealer would cost, but i'm sure you can replace either yourself. ebay is a good place to look
Hope this helps.
I've had a reply from HTC UK who said the following:
That looks like there are a bunch of very small cracks in the screen. the black stuff is likely the Liquid Crystal from inside the display that has leaked out. If the dots get larger then it would definitely seem that the screen has got some cracks in it.
if this is the case, the standard charge for replacing the LCD is around £180 as sadly it is all one complete unit on the diamond 2, so it is not just the LCD underneath that needs to be replaced, but the whole screen assembly including the touchscreen layer and the actual LCD.
I hope this information helps you to make up your mind.
best regards,
Pete W
HTC
Click to expand...
Click to collapse
Reply was fast, I think <1hr from my first email!
I'll see if I can find any HTC Dealer who will send it off on my behalf, but may just end up buying this: http://cgi.ebay.co.uk/LCD-Screen-Di...UK_Mobiles_Accessories_RL?hash=item588362a12d
Hi mate,
had the same problem...
the item you psetd from ebay is not the one you need to change.
you need a digitizer, not an lcd screen.
i got one from ebay (http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItemVersion&item=290376721935&view=all&tid=393718237019), it includes both the lcd and the digitizer, you can check ebay to find other auctions offering the digitizer only.
you can change the digitizer on your own if you don't mind loosing the waranty of your phone.
cheers
Hi,
I had already found this: http://cgi.ebay.co.uk/Touch-Screen-...UK_Mobiles_Accessories_RL?hash=item5882e7ef74
Will buy in a bit, funds are a bit short today.
The Touch Screen's functionality hasn't changed at all though, no sticking buttons or anything. So I suspect that its the LCD Screen thats damaged but will follow you're advise as you're going to have more experiance than me (and its the cheaper part to begin with!)
Scrap the above post.. my g/f has just told me that the dots on her phone are bigger/worse. Looks like its the LCD Screen afterall
i still believe it is not the LCD.
the digitizer is actually sitted on a glass, and the LCD is below that. it is very difficult to harm the LCD. i also though it was the LCD (at least i wasn't sure which was broken) so i ordered both of them.
if you disasseble the phone you will be sure if it is the LCD or not.
i vote for the digitizer
good luck, if you need any help, i'll be pleased to help you..
Just to update, A few days after I posted and got helpful advice on here.. she called me up to say the dots have disappeared, and they have still gone now a few days after.
She said she put it in the office where she works, under a printer paper tray, and the office was warm. Something has (maybe only temporarily) fixed it.
I´m having the same exact problem my nephew dropped my phone, i already dissemble it because i was not sure of the lcd type, but when i looked at the digitizer i didn´t see any dots, so i´m not sure what to repair, TS or Digitizer, i allready tried with the tape to pull the digitizer, when it was apart i couldn´t see anything on the lcd no marks at all, opinions please.
cheers
Well F**K me! just bought a second hand diamond 2 to replace my xperia...
...seemed to work great checking it out... went home with the phone in my pocket... and as soon as I turn it on the touch screen doesn't work
dissected the whole phone only to discover the digitizer is glued to the bezel!
I ordered this from Ebay, will update if I got it working with the brand new housing + digitizer: http://cgi.ebay.it/ws/eBayISAPI.dll?ViewItem&item=380166349182&ssPageName=STRK:MEWNX:IT
fingeres crossed
Please report back here on this thread if it works
fluke said:
I´m having the same exact problem my nephew dropped my phone, i already dissemble it because i was not sure of the lcd type, but when i looked at the digitizer i didn´t see any dots, so i´m not sure what to repair, TS or Digitizer, i allready tried with the tape to pull the digitizer, when it was apart i couldn´t see anything on the lcd no marks at all, opinions please.
cheers
Click to expand...
Click to collapse
Can any one help with this matter?
fluke said:
Can any one help with this matter?
Click to expand...
Click to collapse
If you can make some photos of the digitizer and the lcd dissasembled maybe, but It seems unlikely to break the lcd when you didn't completely trashed your digitizer.
jodeltje said:
If you can make some photos of the digitizer and the lcd dissasembled maybe, but It seems unlikely to break the lcd when you didn't completely trashed your digitizer.
Click to expand...
Click to collapse
Thanks for the reply as I said previously:
I´m having the same exact problem my nephew dropped my phone, i already dissemble it because i was not sure of the lcd type, but when i looked at the digitizer i didn´t see any dots, so i´m not sure what to repair, TS or Digitizer, i allready tried with the tape to pull the digitizer, when it was apart i couldn´t see anything on the lcd no marks at all, opinions please.
cheers
Click to expand...
Click to collapse
Also the LCD didn´t had any marks at all, but i´m going to buy the TS+LCD and replaced by parts first the lcd because it´s a lot easier to replace then if the problem persists the TS.
I will post the result later when i get the parts to replace.
Superman_1122 said:
I've had a reply from HTC UK who said the following:
Reply was fast, I think <1hr from my first email!
I'll see if I can find any HTC Dealer who will send it off on my behalf, but may just end up buying this: http://cgi.ebay.co.uk/LCD-Screen-Di...UK_Mobiles_Accessories_RL?hash=item588362a12d
Click to expand...
Click to collapse
Can anyone confirm the above link as being both Lcd and Digitizer? I'm sure it doesn't mention it in the listing but the picture looks like it's showing both connectors.
Most likely only the LCD that's my conclusion if you look at the sellers store.
But to be sure e-mail the seller and ask.
http://stores.shop.ebay.co.uk/Elect...QQ_sidZ195653022?_nkw=diamond+2&submit=Search
Soooooo, as I've already posted here, My digitizer was busted on the phone I just bought... what I didn't tell was that I ordered a digitizer, then checked if I could remove it easily...came to the conclusion that I couldn't... and ordered a digitizer+housing so I could easily fit it on.
the mail brought me the digitizer today, and while knowing a better solution was on it's way I couldn't resist and try if I could make it work.
Turns out it super easy to seperate the digitizer from the bezel using a hairdryer (softening the glue) and a knife:
Take your phone apart, just the 4 screws, click the plastic center off it. Remove the digitizer cable, the touchscreen cable and the speaker cable.
now you are able to remove the green plate which holds all chips and stuff.
underneath that is the screen, lift it up gently going under it from the gap the removal of volume buttons leaves, put it away safely.
Now remove the speaker, the buttons under the zoom bar, and the power button(don't forget the the power button, and rubbery thingy that falls out of the bottom, the hole needs to be at the bottom when putting it back in).
your phone should be completely empty by now... just the front and the digitize glued together.
make the front of the phone reaaaaaaaaaallllly hot, put the knive between the metal and the digitizer (I started at the part where the zoombar is) and gently push it between the two parts... (from the inside of the phone to the oudside). Now just keep the whole thing above the dryer to keep it warm and slowly slice your way around the phone (no secret wires are there that you can cut through).
I used some random glue I had lying around to glue the front back to the new digitizer... perfect!
so the screen is like new now
ps bought this digitizer: http://cgi.ebay.nl/Touch-Screen-Dig...wItemQQptZPDA_Accessories?hash=item45eed6effc
Thanks for that jodeltje.
It sounds exactly the same as when i replaced the digitizer on an Omnia. Really not as hard as one might imagine. Taking your time and being careful are the most important things.
Hey guys,
I came into same boat last night.
Dropped my T-Mobile MDA Compact V from 2.5ft table, Backwards (Not towards LCD) and now it has black dots on screen. I guess the LCD has pressed backwards by chip sets.
Here is a screenshot.
I think its LCD damaged but I don't have cash to replace nor device warranty.
Do you think the problem solves eventually? Coz once I had dropped sony mobile and it too had same issue but solved after many days.
Hopefully it solves.
BTW; does LCD affixed to Digitizer? by seeing service manual, it doesn't look like it is. And I afraid to get cheap hongkong LCD screens for about 30$ since they won't be true quality display. i.e blueish.
Thanks...
Best Regards
hello CRACING,
sorry about what happened to you...
from the picture i can say that you have a problem with the digitizer...
your LCD is ok.
i tend to have this problem over and over again the last 1,5 years... i replace the digitizer (or the glass on which the digitizer is attached to) every 3-4 months..
yes the ones you get from ebay are not that good quiality, but well it keeps the phone working...
if you need assistance on replacing the digitizer, i can help you, by providing pictures and istructions...
cheers
Hi, I recently got my HTC One (m7 / at&t) as a graduation present in June. Unfortunately I recently dropped it face down without its case onto the ground and resulted in a large crack(s) on the screen. I can still use the device, text, talk, watch videos etc.. but as you can obviously tell one does not simply enjoy the pleasure of having their phone(s) screen cracked.
So I immediately began looking for a solution and repair shops said 300$ to fix when I purchased my phone for just a little over 300$. So that is out of the question, unless its truely my last resort. So I began looking on how to fix it, youtube failed me the only thing that was helpful were the breakdown videos of the HTC One teaching me how to take apart the phone (The only part I was interested in was on taking out the glass).
The only solution I currently can think of would to repair it myself. So here are my questions.
1) The screen is cracked only, the touch screen works fine etc.. so can someone show me the listing on ebay/amazing (I prefer amazon) of the kit or things I would need to fix it.
I Saw this one:
amazon /HTC-M7-screen-digitizer-replacement/dp/B00CWKGZ5U/ref=sr_1_5?ie=UTF8&qid=1376517625&sr=8-5&keywords=HTC+One+Glass
Because it looks like exactly what I Need, BUT I'm no expert so would that fix my problem? Or is it the wrong thing since all I need is the glass and thats the "Digitizer Outter Glass" or something? I dont know my terms that well but to me it seems like what I need because its the "Outter Glass" haha.
But I'm confused about that because it says Digitizer outter glass and in the picture has the connection cord thing, Would this be replacing every part having to deal with the screen? (i.e I take a suction cup and take out the screen, and unplug the connection from the phone to the screen, would what I having in my phone (cracked screen with cord..) be the same thing as what Ill be ordering from that amazon thing but NOT cracked?)
-----------
2) How would I replace it step by step? I already seen videos of taking the phone apart and replacing iPhone screens but I havent seen any towards the HTC One in regards to replacing the screen. So would someone mind pointing me in the right direction, or giving me a text tutorial on what to do? I can pretty much figure it out by reading it since I have videos n pictures to compare it to sorta.
-----------
3) I never done a repair before but it doesnt seem that hard, just have to be gentle and know what youre doing (Thus why im asking so many questions), is this my best option? Or what should I do...
-----------
4) When I seen videos regarding the iPhone screen replacement it was showing things like Screen Seal / and him literally taking off the glass from the this other thing and replacing just the glass itself instead of the thing below it.
Would I have to also use a type of screen seal / or have to take glass off like you would do in the iPhone or is it a 100% different conecpt / idea?
----------
Remember: I basically need to know what I need to fix the cracked screen of my phone, I think this is what i need:
amazon /HTC-M7-screen-digitizer-replacement/dp/B00CWKGZ5U/ref=sr_1_5?ie=UTF8&qid=1376517625&sr=8-5&keywords=HTC+One+Glass
So if it is, then may someone tell me how to replace my phones cracked screen using that and explain it to me what im actually doing and watch each part is etc.. (like what im buying and whats cracked with my phone, so I know its what I need)
and if not, can someone tell me what I need and how to do it?
PS I understand I cant post outside links, but its amazon and Im not trying to advertise i just need the link as a comparison / example
This is one of the worst phones created when it comes to repair. It is well made, but ease of repair was not their priority. The only thing I can recommend to you would be to go to the Ifixit web site. They do a tear down of the phone to show how hard it is to repair. Maybe that will help you out.
Edit: In your original post, you wrote that you had watched videos on the Iphone. Since this is a different phone with differences in assembly, I suggested a video concerning this specific phone. Not trying to be rude, but if I was taking apart my HTC, I would view specific videos concerning my phone. I thought that the specific video might give you clues as to the parts involved in assembly and what procedures were necessary. The video I was referring to concerned their taking apart an HTC One. Every bit of information might be helpful to you trying to fix your problem.
Wolf said:
This is one of the worst phones created when it comes to repair. It is well made, but ease of repair was not their priority. The only thing I can recommend to you would be to go to the Ifixit web site. They do a tear down of the phone to show how hard it is to repair. Maybe that will help you out.
Click to expand...
Click to collapse
Not being rude but I'm pretty sure I already stated the fact that I seen the videos and tutorials regarding the tear down of the phone. So how do you expect that to "maybe" help me out? If I'm trying ti find out the part(s) I need to replace since I don't know the full termology.
I know how to take my phone apart (For the most part), I Just need to know mainly what I need to replace to fix my cracked screen, or whats my best solution. + The questions i stated in the thread.
Thank you.
Unfortunately you will have to change the whole screen assembly.
This will cost you a little ... http://www.etradesupply.com/oem-htc...itizer-assembly-with-front-housing-white.html
You could try also just the LCD+ digitizer (if the front aluminum parts are still intact: http://www.etradesupply.com/oem-htc-one-lcd-screen-and-digitizer-assembly.html
If you scratched the back of the phone, those guys have the back assembly also ... about 24 USD ... ( http://www.etradesupply.com/oem-htc-one-rear-housing.html )
You could TRY replacing only the digitizer ( http://www.etradesupply.com/oem-htc-one-digitizer-touch-screen.html ) but I would not go there. In between the digitizer (what is actually cracked in your case) and the lcd there is a special "jelly" glue which is VERY hard to remove w/o breaking the LCD. I tried that on a N7 and now I'm waiting for a new LCD to be delivered ...
Good luck!
Thank you, I appreciate the reply.
My casing / housing isnt broken (The cracks start from the top of the screen right below the camera/speakers where the glass is, and the crack(s) end towards the HTC Logo etc..) so should I still buy the white housing with lcd+digitizer or should I just go with the second option and buy the digitizer+lcd without the housing (second link you gave me)
JohnVerde said:
Thank you, I appreciate the reply.
My casing / housing isnt broken (The cracks start from the top of the screen right below the camera/speakers where the glass is, and the crack(s) end towards the HTC Logo etc..) so should I still buy the white housing with lcd+digitizer or should I just go with the second option and buy the digitizer+lcd without the housing (second link you gave me)
Click to expand...
Click to collapse
Let us know how it went. :good:
Not sure if it's worth it. HTC will fix it for you somewhere around $180.
Sent from my HTC One using xda app-developers app
JohnVerde said:
Hi, I recently got my HTC One (m7 / at&t) as a graduation present in June. Unfortunately I recently dropped it face down without its case onto the ground and resulted in a large crack(s) on the screen. I can still use the device, text, talk, watch videos etc.. but as you can obviously tell one does not simply enjoy the pleasure of having their phone(s) screen cracked.
Click to expand...
Click to collapse
Hi,
I posted a lengthy thread on how to do a repair here
http://forum.xda-developers.com/showthread.php?t=2387992
Did it well over a month ago and it is still running fine.
You might want to call you household insurance, and tell them someone in your household (not you) dropped the phone while cleaning for example.
Here in the Netherlands, they will pay the repair even the same day.
I didn't had to send them anything, just tell them on the phone how much the reparations would cost, and they transfered the complete numeber right away!
Too bad I found that out after spending more than $100,- on phone reparations.
It might be worth the shot, since they may reimburse it for you.