Kaiserunlocker RUU Problem - Tilt, TyTN II, MDA Vario III General

I downloaded your Kaiserunlock utility and, followed your step and when my phone was ready to finished updating ( 95%) i got a message that it disconnected so I went thrh the recovery feature and now my 8925 is stuck in my tricolor screen and I keep trying the recovery PDA recovery ROM utility 3.14 program and nothing happens keeps doing the same over and over the whole process, advice please.

bump
/bump************

What you need to do ,is reflash back to your original rom, found here
http://wiki.xda-developers.com/index.php?pagename=Kaiser_ROMs
And then follow these steps to do it right.
http://forum.xda-developers.com/forumdisplay.php?f=378

Related

bricked hera100 need help

Hi
I have HERA100 which is stuck on start up logo and can not complete booting, for flashing I have to put the phone on boot loader mode, it gives me the following data:
IPL 4.11.0002
SPL 4.11.0000
need advice on which files should be used to revive my phone?
WBR.
enter bootloader(hold camera and poke hole on side)
then get the official ROM(if its a tmobile wing) then flash it.
p.s. i dont think you need the official rom. ive bricked my wing and just reflashed a different ROM
I already tried that, but the upgrade process stops at 2% and the phone reboots with same condition (stuck on start up logo).
By the way, the start up logo is O2 and not Tmobile.
WBR.
hmm are you trying the same rom that bricked your phone?
I tried more than three different roms, most of them stops at 3%, one of them stops at 2%.
is there any special procedure should be done?
WBR
i dont know what else.
try reading this: http://forum.xda-developers.com/showthread.php?t=345411
This happen to me before u have to use the RUU and enter the boot loader through the process u were given in the previous post
your phone is an o2 xda terra. there is no ruu for the terra.
Put your phone in bootloader and use USPL or HardSPL to flash a custom rom to your phone. You will have to HardSPL your phone as it is not yet HardSPL'd if you choose to take that path. In any case, USPL is preferable until you're out of warranty
but the phone can not work in normal mode, how can I use the hardspl or uspl in my case ( phone works only in boot mode)?
for USPL: This will work in bootloader
Download it, put it in the right directory, slap in the .nbh file, FLASH-IFY!
for Hard-SPL: This MIGHT work in bootloader
Download it, press the button
a bit vague, but thats the gist of it. Use USPL

Flashing ROM and SPL

Hello all,
first let me apologize for the long post, and my noobiness. I'm new to the smartphone world, I've sucessfully flashed my Kaiser (from work). Also, I would like to thank everyone who is cooking!
I have the HTC Mteor, which I'm trying to Flash to WM6.1.
When I got it (used), I did a hard reset, and it went back to WM5 in Russian.
I believe I successfully unlocked it, and can now get to the tri-color screen.
It reads:
BBEE100
IPL-0.90
BREE100
SPL-2.05
Every ROM (including the original from HTC) opens, forces the phone to the tri-color screen, and then dies. Error 260, 262, etc.
I've searched the forums, and read that the SPL should be 1.10, but I can't get that to install either.
Any help/suggestions?
Thanks,
Jeff
jjmorris100 said:
Hello all,
first let me apologize for the long post, and my noobiness. I'm new to the smartphone world, I've sucessfully flashed my Kaiser (from work). Also, I would like to thank everyone who is cooking!
I have the HTC Mteor, which I'm trying to Flash to WM6.1.
When I got it (used), I did a hard reset, and it went back to WM5 in Russian.
I believe I successfully unlocked it, and can now get to the tri-color screen.
It reads:
BBEE100
IPL-0.90
BREE100
SPL-2.05
Every ROM (including the original from HTC) opens, forces the phone to the tri-color screen, and then dies. Error 260, 262, etc.
I've searched the forums, and read that the SPL should be 1.10, but I can't get that to install either.
Any help/suggestions?
Thanks,
Jeff
Click to expand...
Click to collapse
install this official rom from HTC
http://rapidshare.com/files/66085556/RUU_BREE100_1.34.261.1_1.38.00.10_HTCRUS_SHIP.exe
Its for RUS QTEK_AO7.
Then you will have SPL 1.10
I have similar problem
I had ROM 6.1 from Futureshock...still problem with radio (my phone couldn´t accessble but signal icon shows good signal, radio version 1.38.0000), so I decided flash some original ROM. Aftet that my booting stuck on HTC logo or Windows Mobile logo. So I can´t use normal way to flashing. Only from SD card or first turn on phone to boot loader mode and than attach usb cable and start flashing. From SD card (where is renamed ROM BREEIMG.NBH) after enter into bootloader mode start loading and than just turn to trhreecolour menu where is BREE100 - IPL-0.90 and BREE100-1.10.0000 and doesn´t want continue. If I flash ROM via USB cable (first go to threecolour mode, than attach cable) than run ROMUpdateUtility.exe and flash process is being started but always die on 2%, than autoreboot and again stuck on HTC logo.
I tried soft reset, I tried lot of ROM versions HTCRUS, HTCEUR, QTEKEUR, FUTURESHOCK but still same problem during flash ROM stop on 2%...
Any ideas how to back life to my MTeoR?
Can I use application like MTTY? Could me help this program?
Thanks for any help...
hi, can any1 send me a link for a ger version of wm6.0pro ?
Wigo said:
I had ROM 6.1 from Futureshock...still problem with radio (my phone couldn´t accessble but signal icon shows good signal, radio version 1.38.0000), so I decided flash some original ROM. Aftet that my booting stuck on HTC logo or Windows Mobile logo. So I can´t use normal way to flashing. Only from SD card or first turn on phone to boot loader mode and than attach usb cable and start flashing. From SD card (where is renamed ROM BREEIMG.NBH) after enter into bootloader mode start loading and than just turn to trhreecolour menu where is BREE100 - IPL-0.90 and BREE100-1.10.0000 and doesn´t want continue. If I flash ROM via USB cable (first go to threecolour mode, than attach cable) than run ROMUpdateUtility.exe and flash process is being started but always die on 2%, than autoreboot and again stuck on HTC logo.
I tried soft reset, I tried lot of ROM versions HTCRUS, HTCEUR, QTEKEUR, FUTURESHOCK but still same problem during flash ROM stop on 2%...
Any ideas how to back life to my MTeoR?
Can I use application like MTTY? Could me help this program?
Thanks for any help...
Click to expand...
Click to collapse
I'm not sure that I understand well, but if you flash from SD, it finish in 100% and than go to three color boot screen? ....
Hi alebo caf Vašek ;-)
My problem is that always stuck on boot image HTC or Windows Mobile blue screen. I can´t use way copy necesseary files to root of phone memmory and than run sspl etc...I have to turn manualy to three-color mode, than connect USB cable and run upgrade utility but still froze instalation on 2%, If I use SD card methode with BREEIMG file uploading doesn´t start....
p.s.: Ak by si mal dáku radu tak možno lepšie vysvetliť po česky ;-). Moje ICQ 208-393-971
Dík
CZ Rom
I would like to install new ROM into my Mteor, but I have no experience doing it. I do not know which version to try, all I need is to be able to enter czech letters on HW keyboard as with original ROM. Any sugestion? I preffer personal answer in czech language ([email protected])

[FIXED] HELP Bricked my device!!

Please help.
I wanted to update my SPL to stock (from HSPL) to be able to install the 1.56 stock ROM. What I did was:
1. downloaded 1.15 stock SPL from HSPL thred
2. Tried to flash it with the HSPL package (as described in HSPL thred)
3. After no sucsess (the RRU told me that there is comucation problem) I restarted the device and the copyed the .nbh with stoch SPL to the SD Card. Then in Boot loader mode flased the SPL.
Now the device boots every time in Boot Loader displaing ROM update Error and then on the white background it shows "Loading.." and nothing hapens!
How to correct it? Please help
put your original rom (the one you had when buyed the phone)............
happened to me this morning ....
after 30 minutes, I managed to turn off my HD, I put back the SD, the previous cooked ROM
I run the bootloader and everything is back ok!
great fear
They changed something in the house HTC
I finaly fixed it! What I did was to remove the SD Card, then Windows XP Found some new devices and the RRU connected to the phone and flashed it! Its a relief!
good man

[Q] htc hd7 firmware update gone wrong

I recently tried to update HTC HD7 firmware after a hang issue. I had hard reset the phone and the phone now boots in bootloader mode. I cannot exit the bootloader mode. Also, I may have tried flashing the device with RUU_Schubert_hTC_Asia_WWE_2.20.841.02_Radio_5.65.09.11a_22.44.50.15_NoDo
When the ROM version of the phone is 2250.09.12302.707. Now my phone is unusable. It starts in bootloader mode any attempt to flash it with other 707 ROMs RUU_Schubert_hTC_Asia_WWE_1.57.707.02_Radio_5.52.09.16_22.33a.50.10_Signed_SCHUBERT_RELEASE fails with a update error 270: saying the ROM file is corrupt please help. My phone is unbranded.
Thanks,
Please help
The windows phone support tool 'might' be able to help you out here.
://support.microsoft.com/kb/2530409
Unfortunately as a noob to the forums I can't post links. Add http to the above to make it into a link.
I had the same problem, but i managed to solve!!!
Invert the flash order from this thread: http://forum.xda-developers.com/showthread.php?t=1000520
Flash b2 (big one) first and ignore the error then flash b1 (small one) and the phone will boot
Now guys my phone is toast. It does not work beyond the bootloader mode. I tried flashing the device but the process gets stuck at 0%. I tried formatting the SD card but the same tricolor boot screen appears. What the hell has gone wrong? Anyone who can help me thanks a million. I would really appreciate it.
did you try flashing one of these 707 roms ?
http://forum.xda-developers.com/showthread.php?t=888747&page=20
if u stuck in bootloader mode, pull out the battery , and install it back again
It could be a faulty USB port during the flash process. Try another USB port.

Bootloop after firmware flashing

He guys,
now i'm having my first problem.
I flashed the latest firmware: 4.06.1540.3 (its not my first firmware i flashed i flashed a lot) but after rebooting my phone shows the HTC with a warning in it and i can't get into recovery or something. When i try to get into bootloader its boots instantly.
Whats wrong here?!
edit: when i try to turn it off with power and vol down it doesnt really turns off it just reboots and the small HTC one with the red warning logo in it.
kewkie said:
He guys,
now i'm having my first problem.
I flashed the latest firmware: 4.06.1540.3 (its not my first firmware i flashed i flashed a lot) but after rebooting my phone shows the HTC with a warning in it and i can't get into recovery or something. When i try to get into bootloader its boots instantly.
Whats wrong here?!
edit: when i try to turn it off with power and vol down it doesnt really turns off it just reboots and the small HTC one with the red warning logo in it.
Click to expand...
Click to collapse
Which guide you've used?
And what's your bootloader situation? Relocked? S-OFF?
I had similar today, could only get so far with adb, what I done to get outta boot loop was: (links included)
1) install latest twrp following vomers guide
2) went into RUU (followed Vomer's guide from SECTION 3)
3)went here (htc1guru.com) downloaded the exe VERSION, with phone plugged in and in ruu mode ran the exe installer, - installed the rom - easy - push a few keys, set phone up then
4) downloaded HTC_One_-MaximusHD_30.0.0 and installed that through recovery
now im back up and running
Hope this helps - I was almost going back to the shop - with a bricked phone lol - now im happy
Thanks guys, i managed to get it work tho.
I just let it off for a while and then it worked again.. dont know what was that

Categories

Resources