alpine with software locked on it - PDA2, XDA IIi, 2020i General

hi new to all this pda stuff, canany one help me!!!!!
i have been given a pda alpine, but it is locked with a program i carn`t get it to go into windows.
what is the best way way to get rid of this software?????
thanks

i assume you have tried hard resetting and then soft resetting once the HR has finished, in the wee 3 second window where it says customising.
Other suggestion would be to flash a new ROM.

big thanks!!!!!!
i said i was a newbii
ok i can start now, i have windows mobile on, ok whats next for me to do?????
how can i get rid of all that old software ??????

What sort of old software do you want to remove?
A hard reset should only leave you with whatever the carrier has decided to give you. If you do the soft reset trick you should be able to remove any carrier specific customisations leaving you with a bare(ish) Alpine. What you load after that is up to you.

ok so the software that was on when you started up the system has now gone???
i just have windows mobile on now when i start it up.
also i used the unlocker wizard, and it said it had unlocked, but i now have a no network ! mark instead of a strength signal???
any ideas please

Which version of the unlocker did you use? i had more luck with the older version. It sounds as though it hasn't worked, despite saying it had. From memory it does take a while to complete. Have you tried it with any SIM apart from your own one?

i used ver 1.6
and yes tryed it with 2 other sims, but still no luck they both the same.
is there anyway to reformat these pda`s start a fresh as they say
i said iam new

Yup, that's the newer version, i used version 1.5, SIM unlock.

Related

Error 114, help me please,I'm helpless.

Hi All
I have a SPV M2000.One day the phone stopped working. Everything was all right, it did ask for pin but then didn't even looked for network,was immediately saying NO SERVICE. I tried few sim cards - the same.
So then I wanted to reinstall the ROM, I downloaded the official from Orange UK , tried to install it,and it shows ERROR 114, Radio Rom Upgrade Error.
And the phone now is in bootloader mode and I can't do anything!
I downloaded different ROM from xda-developers ,at the beggining with a country error, but i managed to fix it and now with this ROM it's the same thing. ERROR 114. I tried everything, hard,soft reset, Pc reset etc. Nothing works!PPC still in bootloader mode!
Please tell me if you know what else can I try!
Guys,come on,really noone knows???
Have you read WIKI? Follow the first method to flash your ROM. Have you remembered to plug in your power supply to your cradle when you flash your device?
Heres another thread on NO SERVICE Plz help... No Service after radio upgrade. Happened to me. Read it and see the advise by MDAIIIUser and TheLastOne. If all else fails, bring it to the shop.
I had a very similar problem....
First I tried to update a whole package that means rom, extended rom and radio
The radio update is always the first one and there always upgrade error 114 occured.
So I updated every part seperately and it works except the radio. So I tried alot but it just didn't work..even downgrading was impossible. MDAIIIuser and happy goat tried to help me as well as they could but nothing had an effect.
So I read in another forum that asus mainboards have some problemes with these radio updates....I thought they were joking...but I tried the radio pdate at another pc and it worked!
I know it sounds a bit stupid but I was desperate and at last it worked!
You can read it here :
http://forum.xda-developers.com/viewtopic.php?p=89657#89657
TRied that method.Doesn't work
Any other ideas?
One more thing.Is it normal that in bootloader mode when I plug the power cable in the charging LED is not working?it was working before.
The battery is charged ,but shouldn't it show that the power is connected anyway?
EDIT: this is a reply to the first answer.
So you think I should try on another PC?I will today!Hopefully it will work.
So I managed to install new rom on a different computer! I think that there was a problem with active sync.I used the one that was installed from my old XDAII.Could that be the reason?Now i installed the one provided with a M2000.
But it doesn't work anyway
Still NO SERVICE message.
ANy other ideas different than taking it to Orange?
Hi rottie,
No Service could mean anything. Could your SIM card be faulty? Device SIM locked? Or hardware faulty? You cannot just use any ROMs you find at ftp. Try to flash your device with full shipped rom at http://wiki.xda-developers.com/index.php?pagename=BA_1.40.00_Upgrade. Use the first method and upgrade using MaUpgradeUt_noID.exe to bypass the Country code error. Remember that you'd need to run MaUpgradeUt_noID.exe twice.
Read wiki carefully, it has alot of precious information. Cheers ^^
Before you update any version you should be sure that your radio is
compatible with your device. Usually all radio upgrades should be
independent off the language of the device but as I understood (could be
wrong) there are differences because of the servicenetwork frequency.
So you must be sure that the chosen radio is compatible and that your
device is not simlocked.
So perhabs you should chose an upgrade of your provider.
But perhabs itis better not to risk your guarantee of your provider by
using updates or components of other providers! Because there could be
the possibility that your device is damaged and you should bring it back!
Good luck!
Guys, you get me wrong.I'm not trying anything what I'll find.
1)One of the ROMs that I tried and the one that I left now is a ROM downloaded from orange.co.uk for SPV M2000. So there can't be any incompatibility, don't you think?
2)I have 2 sim cards,both from Orange,I was using both of them before in my M2000 which is sold only through Orange so there can't be any simlock problem,don't you think?
3)I used only that orange ROM, original and the I-Mate one.None of them were working good,always NO SERVICE.
I bought the phone second hand,with box,all accessories etc. But I don't have a receipt :? And of course have lost the guy's number.That's why I want to try everything before going to the service.
I think this phone is network blocked, probably been reported damaged or stolen, once the insurance or replacement is issued a block is put on the imei of the phone that was subject to claim.

Forcing Bootloader Mode

Maybe some of you are already aware of this procedure, maybe not.
Anyway, it worked for me and I decided to share how to do it. Simple.
This procedure should only be used in case you really need enter into a bootloader mode and all other ways to do it has failed! Hold Camera button is one of these I am mentioning.
My Wizard was almost bricked at that time and after I speak with an I-mate technical guy, I got the following:
1. Make sure your i-mate™ K-JAM is not Connected to the PC and remove the dummy card or SD/MMC card
2. On your Desktop PC, open Microsoft ActiveSync, then go to File >Connection Settings >Remove the Selection from “Allow USB Connection with this desktop computer”
3. Reconnect your i-mate K-JAM to the Desktop PC using the USB Cradle and the Charger MUST be Connected to the Cradle (Don’t use the IrDA or Bluetooth for the Upgrade)
4. Run the Upgrade again and it will work fine without any problems.
While upgrading, the ActiveSync program will not go on, however the upgrade is running.
Hope it helps!
this realy worked for my (ex)bricked dutch tmobile mda vario !!!!
tip: REALY make shure that there is no wcescomm.exe running all the time and realy remove the sd card else is nogo
btw: my wizard is CID locked! and works like a charm
Thanks buddy!
I'm happy that worked for ya!
Take care!
I'm having a problem
The power went out as I was upgrading my Wizard (Cingular) so now it just turns on at the boatloader screen. I've tried running updates while it was in this screen (it did show the "USB" in the white bar) but most of the time it tells me there is a connection error. Even if I kill Activesync, I notice that when I run the update utility it still runs Activesync. I've tried disabling the USB connection but still get the connection error.
The only time I haven't gotten the connection error was twice it asked me to update but then told me I had the wrong file. This only happened when I tried "upgrading" to 1.05 as I was trying to start again. After it tells me that if I try running it again it gives me the connection error.
Any ideas?
Hi!
Have you already flashed your device once?
Which ipl/spl do you have?
I had problems over 1.05 ROM in the beggining.
If you stuck on bootloader mode, that's a good signal your device is not bricked.
I'd recommend you to disable activesync as you did and reflash it again! Check also if your device is CID unlocked! Search for a thread in the xda developers root.
Try to upgrade to ipl/spl 2.26 first and later to others you want.
Regarding the old file error...can be related to a missing file called enterbootloader.exe.
Hope it works for ya!
Take care
Ironman273 said:
I'm having a problem
The power went out as I was upgrading my Wizard (Cingular) so now it just turns on at the boatloader screen. I've tried running updates while it was in this screen (it did show the "USB" in the white bar) but most of the time it tells me there is a connection error. Even if I kill Activesync, I notice that when I run the update utility it still runs Activesync. I've tried disabling the USB connection but still get the connection error.
The only time I haven't gotten the connection error was twice it asked me to update but then told me I had the wrong file. This only happened when I tried "upgrading" to 1.05 as I was trying to start again. After it tells me that if I try running it again it gives me the connection error.
Any ideas?
Click to expand...
Click to collapse
My device is unlocked as I've been trying different ROMs as of late. I had gone back to the Cingular 2.25 ROM for a couple days to sort some things out and was going to flash Farias AKu 3.3 when my power problems happened. My Current IPL/SPL is 2.25
I've tried flashing the TMobile 2.26 but keep getting connection errors. In fact, I've tried flashing with every ROM I have pdviet 3 and 4, CIngular 2.25, TMobile 2.26 and Custom 1.05. Everything (except twice in the custom) gives me connection errors.
Any other trick I can try?
BTW, I used to live in Sao Paulo years ago...
Edit: OK, so I tried the 2.26 TMobile ROM after I typed this and it worked!! I'm back up but I was having trouble with that ROM beause of some incompatibilities with Cingular. I'll go back to Cingular's ROM and play it safe for now.
I believe part of my problem was I kept trying different updates one after the other. Now that I think back, the 2 times I got the update to almost work was after I turned off the device and turned it on again, which is what I did this time around also.
I had the same problems as mentioned by Ironman before. I followed the steps and with a few slight changes, I managed as well to "unbrick" my wiz. THANKS A LOT for the great step by step manual!!!
Still I wanted to know WHY i bricked my device:
I was trying to upgrade to the underground WM6 ROM. I got the same situation as ironman:
Quote:
The power went out as I was upgrading my Wizard (Cingular) so now it just turns on at the boatloader screen. I've tried running updates while it was in this screen (it did show the "USB" in the white bar) but most of the time it tells me there is a connection error. Even if I kill Activesync, I notice that when I run the update utility it still runs Activesync. I've tried disabling the USB connection but still get the connection error.
The only time I haven't gotten the connection error was twice it asked me to update but then told me I had the wrong file. This only happened when I tried "upgrading" to 1.05 as I was trying to start again. After it tells me that if I try running it again it gives me the connection error.
Unquote
I then followed the instructions by epimazzo as written above. I also tried the T-Mobile ROM 2.26 which was not working for me. PANIC!!!! Error messag was that I had the wrong Vendor ID. THerefore no upgrade to TMob 2.26 was possible. I tried it then my original qtek ROM in my language and see it worked!!! This IMHO means that I did not put the device in a proper IPL1.xx and SPL 1.xx status which is required for a clean system in irder to unlock it! So if it is bricked, try your native AKU2 ROM and make sure you unlocked it properly. Maybe you have to run the 1.05 ROM for a second time after the unlocking.
I hope this helps you guys.
Sounds great to hear that!
I had play around with pdaviet3, underground and another ROM just today without any problems at all. I don't think that this is the case. Now you get your device back to normal, try to reflash it again. Hope it works this time!
BTW,...São Paulo is a nice city. Thanks! Let me know if you decide to come here!
Take care
Ironman273 said:
My device is unlocked as I've been trying different ROMs as of late. I had gone back to the Cingular 2.25 ROM for a couple days to sort some things out and was going to flash Farias AKu 3.3 when my power problems happened. My Current IPL/SPL is 2.25
I've tried flashing the TMobile 2.26 but keep getting connection errors. In fact, I've tried flashing with every ROM I have pdviet 3 and 4, CIngular 2.25, TMobile 2.26 and Custom 1.05. Everything (except twice in the custom) gives me connection errors.
Any other trick I can try?
BTW, I used to live in Sao Paulo years ago...
Edit: OK, so I tried the 2.26 TMobile ROM after I typed this and it worked!! I'm back up but I was having trouble with that ROM beause of some incompatibilities with Cingular. I'll go back to Cingular's ROM and play it safe for now.
I believe part of my problem was I kept trying different updates one after the other. Now that I think back, the 2 times I got the update to almost work was after I turned off the device and turned it on again, which is what I did this time around also.
Click to expand...
Click to collapse
It seems you got the idea!
You did the right thing! Sometimes, use the official ROM can solve many issues out there!
Keep walking!
enlite_de said:
I had the same problems as mentioned by Ironman before. I followed the steps and with a few slight changes, I managed as well to "unbrick" my wiz. THANKS A LOT for the great step by step manual!!!
Still I wanted to know WHY i bricked my device:
I was trying to upgrade to the underground WM6 ROM. I got the same situation as ironman:
Quote:
The power went out as I was upgrading my Wizard (Cingular) so now it just turns on at the boatloader screen. I've tried running updates while it was in this screen (it did show the "USB" in the white bar) but most of the time it tells me there is a connection error. Even if I kill Activesync, I notice that when I run the update utility it still runs Activesync. I've tried disabling the USB connection but still get the connection error.
The only time I haven't gotten the connection error was twice it asked me to update but then told me I had the wrong file. This only happened when I tried "upgrading" to 1.05 as I was trying to start again. After it tells me that if I try running it again it gives me the connection error.
Unquote
I then followed the instructions by epimazzo as written above. I also tried the T-Mobile ROM 2.26 which was not working for me. PANIC!!!! Error messag was that I had the wrong Vendor ID. THerefore no upgrade to TMob 2.26 was possible. I tried it then my original qtek ROM in my language and see it worked!!! This IMHO means that I did not put the device in a proper IPL1.xx and SPL 1.xx status which is required for a clean system in irder to unlock it! So if it is bricked, try your native AKU2 ROM and make sure you unlocked it properly. Maybe you have to run the 1.05 ROM for a second time after the unlocking.
I hope this helps you guys.
Click to expand...
Click to collapse
Excellent post. I messed up with my own cooked ROM and could only get the bootloader screen. Tried the tips here - didn't work first time but I pulled the battery from the KJAM to reset it rather than using the reset button and it worked fine.
In my opinion this thread is so helpful to people who brick their device, it should go "sticky". Mods anything you can do about it?
Thanks buddy! I really appreciate!
We survive here over tips like that!
jt_armstrong said:
Excellent post. I messed up with my own cooked ROM and could only get the bootloader screen. Tried the tips here - didn't work first time but I pulled the battery from the KJAM to reset it rather than using the reset button and it worked fine.
Click to expand...
Click to collapse
Help me similar problem
I upgraded Super Rom, then my Wizard run very slow and no signal (no call out and in- no network at all). And Terible thing is PC could not dectect PPC thought Active Sync. I've soft and hard reset but no use.
So I donot know where to start to re install Rom again.
Please help me....
Hi there!
It seems that you just need to enter into the bootloader mode and reflash it again!
I had similar problems and more during my brick "false" stage!
So, just try to follow my steps here and you should be fine! Once you get into bootloader mode, just use any ROM out there to reflash.
Good [email protected]
thaiphong said:
I upgraded Super Rom, then my Wizard run very slow and no signal (no call out and in- no network at all). And Terible thing is PC could not dectect PPC thought Active Sync. I've soft and hard reset but no use.
So I donot know where to start to re install Rom again.
Please help me....
Click to expand...
Click to collapse
I was about to start a EMERGENCY HELP thread, but I *think* this is the right place instead.
The "touch" of my screen went dead today. It got progressively worse over a few hours, starting with difficulty in using the phone dialer, then random incorrect stuff getting triggered by screen taps.
So I hard reset, and got no response on the fifth alignment cross, meaning 1) "Tap on the screen...; 2) center; 3) top left; 4) bottom left; 5) bottom right. In that I could not proceed with alignment, I hard reset again, and now, at the first alignment screen, i.e. "Tap on the screen...", I have no screen response at all.
I called T-mo, and they are being great about sending a replacement ASAP (and getting me a loaner in the meantime).
BUT, I am running Faria+ AKU3.3 V2... so I clearly have to flash back to T-mo 2.26. I can;t figure out how to do it though, as no matter what I do I am stuck at the first alignment screen!!
HELP!! EMERGENCY!!!
(I have three or four days to get this done, so it's not THAT urgent)
Do a search for Broken Screen. Someone (either in Wizard Upgrading or in the Wizard forum) just had a similar issue with a cracked screen. They downloaded something that allowed them to get around the welcome page.
Actually, if you are just trying to flash a new ROM, don't even mess with it. Go straight to the Boot Loader screen (see the first post of this thread). No tapping necessary until the new rom is on (and that will be the Tmobile then so you would be good.
Thanks for the quick reply. Charging up to green now, and then will try to enter bootloader and flash T-mo 2.26. Will report back.
Worked great. Back to T-mo she goes!!!
BootLoader Mode
Excellent thread but you left out one thing.....exactly how to place your device in bootloader mode.
To clear up any misunderstanding because this is very important....this is how you do it:
Perform a soft reset, when the screen goes blank hold the camera button until a multi colored screen comes up .... That's it !!!!!!
When the unit is connected, USB is displayed at the bottom left.

Bootloader question/trouble

Hey there everyone, I am pretty new to this forum so I must apologize for throwing you all into the deep end. I recently purchased an o2 XDA mini S second hand from a guy on boards.ie here in Ireland. I got the phone and really liked it because it allowed me to get rid of my Dell Axim X3i and mp3 player and keep it all in one device.
After a little bit of more research I discovered that I could remove some of the bloatware from the o2 xda mini S by just hard resetting and choosing the basic option which I than did. Still not satisfied with the overall performance of the XDA I decided to try a rom upgrade. Not wanting to do a totall overhaul I decided to just do a radio upgrade first.
My device is sim unlocked, it was like that when I bought it. I used the latest wizard service tool to CID unlock the device before I even flashed the phone. I also used the wizard service tool to change the nk.nbf file within the o2 mini S radio update into 96000000-GSM.nb. I then used this file to write to the GSM radio code (Bdk 1) according to the wizard service tool in the hopes that it would upgrade my radio version.
Well when I restarted, nothing of the sort happened, on the boot screen I noticed I was now missing my GSM version and when the phone finally got into windows mobile, it did not pick up any signal even though beforehand it could. The phone also became super slow to the point where it was unusable.
I have gone into bootloader mode subsequently after reading on this forum and tried to reflash with a number of updates with active sync disabled and nothing else running with the phone connected via usb to the pc. None of the updates would even pick up the phone or allow me to flash it.
My phone is pretty much screwed, I have a spare so it is not that big of an issue but I would like to make this usable again if at all possible. So my question is how do I flash a rom while the phone is in bootloader mode?
P.S I forgot to include the Current boot screen details:
IPL - 1.05
SPL - 1.05
OS - 1.5.4.2
Hi,
You can use the Wizard Love Rom from here http://rapidshare.com/files/17792050/Wizard_Love_2.26.10.2_WWE_Novii_CF2.rar
Hey there, thanks for the advice, I did download that ROM but like I said before, none of the roms manage to flash my XDA because they all cannot seem to connect to it. Activesync does not even pick it up in windows mode, and even when I have it connected in bootloader mode via usb and I double click on the love rom, it goes through the motions but never managed to "verify the information with the pda"
Try a stock Tmobile ROM but not from bootloader. Also, I would check the activesync app on the device. Make sure it's set to use USB as the default connection method.
A few other steps to try...
Uninstall ActiveSync and install an older version. If still no go, try a newer version.
Try a different USB cable and/or USB port.
Try a different computer with XP, not Vista.
Try flashing it without the SIM card or any memory cards.
If all else fails, you can try the SD card flashing method. There are instructions in the Wiki on how to do it, but always a stock ROM.
Try this one... http://forum.xda-developers.com/showthread.php?t=311027
Updated IPL/SPL and radio 2.69
Hey Devis, I think I have come one step closer, I tried all the suggestions that you made. Except well now my phone will not even go into the operating system when I switch it on. It will boot and the version numbers show but then it just resets itself.
I tried a different usb cable and I am not using vista, tried a different pc and the same result. The one place I did have some marginal success was the sd card method.
Basically what happened is that It backed up the OS from my phone and then reloaded it, not exactly what I wanted since the OS and rom are both screwed on the phone so my question at this point is, is there anyway using the SD card method to load one of the stock roms onto my phone?
I searched around the net and found the opposite to the "r2sd all" function, would be the "s2d" function, would that allow me to flash the phone with a stock rom?
Thanks for your time, I am going to call it a night here in ireland and head to bed.
Ok, if the phone resets then you probbably have a dead/dying battery. Charge it for about an hour or so using the wall charger, not the USB cable. Try to restart it and see if you can get in the OS. I was looking in the SD card method thread and some guy was successful at restoring the image from the SD even though his OS had died. He then had a fully functional phone.
The other thing to do would be to get the image file from someone that has a living and breathing wizard, preferably one with a stock ROM. Since this method is the equivalent of making an image of a PC using Ghost, the restoration of such an image to your Wizard should work just fine.
Just make sure that the other Wizard is SIM and CID unlocked. Or just go buy a Wizard from the store, unlock SIM and CID, copy the image on the SD and flash your device. Or... since u've got a new Wizard in your hands, just take the freaking thing appart and swap the guts return the store bought wizard to the store saying that the thing just doesnt freaking work!
As for the AT commands... it is possible that s2d would workfor you, it doesn't work in my wizard. from what i have been reading it appears that the bootloader is password protected and that password is randomly generated. I haven't played long enough with it to figure out how to get the password.
It looks like you've got some "trial and error" processes ahead of you. There is a wealth of info on bootloader AT commands on Wiki, nothing for the Wizard though. But something may work... not sure.
I could try to get you a ROM dump from my Wizard but I already am on SPL/IPL 3.08 and running WM6. the SPL/IPL version alone wouldn't allow you to restore from my backup.
Hey Devis, thanks for your time, just woke up here, will work some more on the phone today and let you know what is going on
Hey Devis, I did not even get a chance to fiddle around with the phone today, from being able to switch on less than 24 hours ago, it does not even want to switch on now so I am going to officially declared it a brick and move on. Will see if anyone can fix it for me, spent way too much time already when I should be working on my dissertation, thanks alot anyway
Sorry to hear that...
I have bricked one phone myself in the past... my old Pana GD87 and I absolutely loved that phone. I know how you feel.
Good luck with your dissertation.

this concludes the beta test...

Hello all,
first, a big thanks to all the rom developers around. You transformed my Diamond in a usable and enjoyable tool.
What happened to me tonight is very frightening. In fact, I cannot believe what happened.
And this is the story: I was at a birthday party and later in the evening I checked my phone : it seemed to have frozen, so I rebooted it as I do sometimes when I have no other choice. But this time something strange happened : I got the following message "this concludes the beta test of this software release. thank you very much for your time and effort in helping make this a great product for our customers" - what the ... ? No way to make a call, the message is impossible to remove... completely blocked !!!
I don't remember exactly the rom I flashed last because I sometimes change. It might be a dutty's release (75%M sure) - anyway I was in a very bad situation because my wife wasn't feeling well and I couldn't call her without finally borrowing a phone from someone.
I will flash a new rom tomorrow and I hope that the message will disappear but I can tell you that it is a very strange feeling when suddenly your phone refuses to operate normally. It's a nightmare.
I hope that someone has an explanation for this because I don't want to go trough this situation ever again, it's just so annoying to have a phone which tells you "No you can't use me; your trial period has expired" when you need it he most.
Thank you for your opinions in advance
Have you tried a hard reset?
Yep same problem here.
Using duttys 1.93 - Can't get to his website either.
Hard rest does not work - had to reflash back to branded (Telstra) ROM
i'm having the exact problem right now, what can i do to fix this? someone told me to reflash it but how? i'm VERY new to the diamond
hardreset does not work
I bought the phone from a person so it's second hand. The seller did mention he updated the ROM, I'm assuming this is the cause of the problem? help please
thanks!
I am getting the exact same problem.I do not know what to do.
Sigh and since my computer will not sync, I cannot reflash it. Hard set is also a no go.
ya I cant sync it with my computer either... i'm searching other sections on this forum and I cant seem to find one that teaches you how to flash without syncing with the computer
OK i got it well kinda sorta. If you hard reset and just use the date taht dutty had then your phone will load. Do not correct the date and you should also change the date on your computer so that it wont sync. Then donwload his new rom or whatever rom you prefer and then flash it. Then change the dates back. It worked for me.
thanks.. do you have the link for the new rom?
I'm going to give it a try
The link it dutt'y new rom is here http://rapidshare.com/files/162091111/Ruu_Signed_duttys_diamond__V2.9_5_2_20275_RTM_Full_MSVC.zip
just a question how do you flash it?
can you help me? i'm very new to this phone
I had the same problem last night- expired beta software. If I do a hard reset I believe I will loose all the info on the phone, is that correct?
I was thinking that changing the date will work, is there another way to change the date without having to loose the info?
Someone has a reliable link to an instruction on how to flash the ROM?
I am also using throy 2.3, to find the latest release please go to WWW.DUTTYTHROY.NET
Any help appreciated.
!everyone! you can flash roms from bootloader. hold volume down and the little red reset button, keep holding vol down untill bootloader. at the tri color screen, run ruu from host pc. everything will be fine with this method. just like activesync.
ok i to change the time and stuff and it actually can sync using active sync.. however.. when tried to install HSPL 1.24 after the part where the phone will turn black.. i click on the DiamondCustomRUU as instructed
but it says this "The application failed to initialize properly (0xc0000135). CLick on OK to terminate the application"
Is there a way I can recover this without losing all that is on my phone?
Do anybody know the password for the latest ROM 2.9 from Dutty? His page is unavailable right now....
Duttys V2.9 RTM Finale
someone please tell me how to flash.. from scratch? i hard reset my phone.. and i cant get HSPL to work. When i install the activesync way, the black screen turns on then i cant open DiamondCustomRUU
if i do i the bootloader way, when i connect from the three colour screen it cant pick up the phone because it says i'm missing Qualcomm CDMA Technologies MSM
please help been stuck for hours already
i won't flash Duttys ROM again!!! Right now i need my phone and it doesn't work! And if i reflash it i lose my data....
never again!
its you have a problem with duttys rom
you need to use his thread to point out your problems....
not this one.

Upgrade to 6 stuck on windows loading

Hi,
I got given a couple of Treo 750 phones. Both on the Optus Australian Network so I scratched around for days and found the upgrade software. Shows update 2.27
1st one went perfect.
2nd one on same computer got through copying files and executing update and stalled at the start of completing update.
I got the Windows mobile screen show and it just was not loading for ages. Previous one loaded and then asked for input of Date, touch screen settings etc.
The installer can be re run but says no USB connection at the moment.
I have done a hard reset and get the palm display then locks on the Windows Mobile screen.
I saw procedures to use the Mini SD card but the cards I have won't work in any treo, they are not SDHC type but standard 2G ones.
I next found the recovery tool but holding the left lower button and then hitting reset did not work but does work on my good phone where it shows the coloured bars and SPL....
The left button is a bit dodgy so I suspect it may be faulty. Is there anything else I can try?
EDIT: Ok I pulled apart the phone, looks like it had a hard life as broken case around two screws and they would not unscrew easily. Found the tiny button had dry solder joints. Fixed that up and was able to recover using the reset proceedure.
Phone now working.
could you explain in more detail what you did. thanks man
webafile said:
could you explain in more detail what you did. thanks man
Click to expand...
Click to collapse
What would you like to know?
Once I physicaly repaired the phone as indicated in the edit I was able to hold the left hand button (which was faulty) and the reset at the same time that allowed me to get into the SPL mode and recover the phone.
I understand it very little and most posts on these forums are over my head.
I would like windows 6.1 but there is so much information that seems to conflict that I don't know I am game since it is now working on an official 6.0 Optus version.
I am happy to help but if you can maybe tell me where you are at the moment and what you want to acheive and what you have tried I hope I can fill in the gaps for you.
because im new to this to and i got stuck in the windows screen also. so i would like to know what to download and where from and step by step if you could please.
thanks man
webafile said:
because im new to this to and i got stuck in the windows screen also. so i would like to know what to download and where from and step by step if you could please.
Click to expand...
Click to collapse
Ok to start with what country are you in and what telco were you with eg Vodafone etc as you will need that as a start.
USA and im with AT&A
Try the method describe in the thread below - Mine work
Hi, you might want to try this method
Follow it one by one and do not skip a step
http://forum.xda-developers.com/showthread.php?t=460783
I just did mine last Saturday (it was a Vodafone phone)
AT&T should be easier since the Windows 6 ROM is easier to get
If you'd like to update to WM 6.1, you should upgrade first to WM 6
Something i read about the radio not working to full capacity if you upgrade straight to 6.1
As for the WM 6 ROM, i'm sure you can find it
Good luck
Hi All,
I have a Treo 750 and it WAS running WM 6.0 Professional (OFFICIAL) and I got it onto the phone and then tried to install WM 6.5 and then I downgraded to 5.0 and tried to update back to 6 and it bricked my treo, any of you wonderful xda ppl have any solution?
Also, I have tried installing the ROM again (via SD updater) and it looks like this:
SPLASH1 OK
BOOTLOAD OK
GSM OK
Micro P OK
EXTROM FAIL
OS
Update Terminate
UPDATE FAIL
I cant install the windows installer one as WMDC 6.1 or ActiveSync 4.5 WILL NOT show the device up on the computer. I have Windows Vista Home Basic, and when I tried MTTY, the only ports I get are COM1, COM2, and COM3. I can't get the usb to show up. Even with MTTY 0.01 when I got the USB connection, it would not open. Is it Vista? Or am I not doing it right? ANY HELP WOULD BE APPRECIATED TO GET MY POOR TREO BACK!!!!!!!!!
Thanks
~Mike
Try this?
http://forum.xda-developers.com/showthread.php?t=427519
simunlocktreo said:
Try this?
http://forum.xda-developers.com/showthread.php?t=427519
Click to expand...
Click to collapse
Is this universal (i.e. Hermes/BA/Trinity) or just for the Treo 750. I think what bricked it in the first place was installing a custom rom by veisen (WM 6.5)
~Mike
Didnt Work
That one thing didn't work. It keeps coming up ERROR 226: FLASH WRITE ERROR Anything else???
~Mike

Categories

Resources