Related
Hi,
Can I install a new ROM via my SD card because I cannot connect to Active Sync? I've been searching for hours but still can't fix my problem.
I tried to upgrade the radio rom only, but after that there is no radio version, no phone or internet, system on MDA is VERY slow, and I can't connect to active sync.
I can get bootloader up, but I cannot install the stock rom I downloaded from this site, because i can't connect with active sync. I've tried to copy it to an SD card and install from there, but that doesn't work either. In bootloader I do not have USB at bottom left on my screen.
only
IPL 1.03
SPL 1.03
Any help would be MUCH appreciated.
Thanks in advance!!!!!
I have the same problem :-(
It would be very nice if there´s a solution for this problem
Thanks a lot
Daniel
You don't need activesynce
You just need to get into bootloader search for it then run the RUU.
kyphur said:
You don't need activesynce
You just need to get into bootloader search for it then run the RUU.
Click to expand...
Click to collapse
If USB is not showing up in the bootloader (rainbow screen) then the only known way to backup is via SD card. The RUU cannot be used in this case.
You'll want to dig out the original backup that you made when you first got the phone and do a restore boot. Restore the image from the SD card.
If you want the improved radio ROM, I'd suggest restoring from SD card, CID unlocking the device, upgrading to an AKU 2.x ROM (so you've got a 2.x bootloader) and then applying the 2.x radio ROM upgrade.
sd card
Check this
http://en.pdamobiz.com/en/forum/forum_posts.asp?TID=151
I installed a back up rom on my SD card with another phone of a friend of myne
same problem; wizard_radio version-2.25.11
will follow link in above post and see hoe it goes; anyone got any other comments?
no SD backup
well, funnily enough I ran the ROM backup as a precaution, but it seems a. not to have worked and b. to have wiped my SD card, so am buggered whichever way you look at it.
Does anyone have a backup image they could email/FTP to me so I can at least get to USB in bootloader?
THanks,
Jolyon
the CURE
ok, thanks to the tip from a99tandem.
Reset, holding down the camera button, allows you to go into boatloader, and you can flash a ROM from the PC using RUU. Bootloader comes up with 'USB' in the corner.
Thank god for that; that's 5 hours wasted...
Need a favours over here. Recently, i bricked my trinity. P3600 more precisely Dopod D810 (i flashed wrong ROM -> Unpacking cooked rom for trinity but i merge it with -Hermes cmd in NBMerge! houh... so stupid! ). Soo... just not what i expected, Rom flashing stop on half, SR my trin and tada.... 3Color screen bootloader popup! haaarggg, i try flashing another rom using any rom that has same CID *official or cooked rom* (some are 100% thru, but someother not) but like usual it won't start the windows (just blank/black screen with green led[ always on!) Never been like this before! Have been flashing several times using any cooked rom by great chef on trinity but this time! :doh: damn it! my bad.
i found solution on the forum *Unbricking Trinity Stuck on Bootloader* but since my usb port can't be detected on my vista/xp machine, whether i disable AS and changed my usb cable it doesnt work at all, on mtty too! so i can't use that utility. i try run install sspl olipro 1.3 but it never changed my spl at all. now i can't use my trin at all cuz allready dead.
btw this is the info on trin 3color screen bootloader:
IPL 1.00
SPL 3.20 OLIPRO
anysolution for bringing back my trinity from the death? maybe a tools/utility to unbrick trinity from SD or something like that, which not involved any pc connection, without bring this devices to htc center of course.
I hope any expertise on this forum would helped me sort out this probs.
Sorry for my english and thanks for reading my post.
Read this :http://forum.xda-developers.com/showthread.php?t=308691 download splxploit-windows.zip (935.1 KB, 7619 views) put phone in bootloader run splxploit when bootloader change
After this download full rom here is link:http://rapidshare.com/files/21174752/RUU_Trinity_HTC_WWE_1.15.405.5_6275_1.20.00.11_12201_Ship.exe
Then flash full rom bat do not disconnect usb cable in any step.
Before use any step disable active sync.
Usb are dead
Gsmhacks thanks for ure reply. I have tried that one, and lot read ing on wiki. But since i cant use the usb i cant use that splexploit whether on live linuxcd, or .Net version even win version. The usb port cant be opened . I think i broke the usb pin. From the beginning everytime i flashed my trin i never used ruu utility, i always do the sd card method and that is the best and easiest method and it works for me.
I just curious perhaps can anyone or is there any utility to unbrick trin via sd card. I knew a lot a people has bring their trinity life from dead by using htc stackflow splexploit. I hope that was work for me too! Too bad my usb are dead. Damn!
Here what you need bat only work if you have hard spl
If you install hard spl before brick trinity you can use SD CARD to flash trinity. YOu need to formate sd card to FAT32 with Card Reader donwload full rom here is link: http://rapidshare.com/files/21174752/RUU_Trinity_HTC_WWE_1.15.405.5_6275_1.20.00.11_12201_Ship.exe
then extract and file RUU_Signed.nbh rename to TRINIMG.nbh and copy it to the root folder of your miniSD card.
Here is full instruction again also first format sd card to FAT32 !!!! VERY IMORTANT to format sd card to FAT32 or all other step will not work THEN:
1. Extract the .NBH file from your prefered ROM upgrade: In windows use winrar (right click) to extract the contents of the exe file. In Linux / MacOS use cabextract (or you can also use winrar via wine).
2. Rename the .NBH file to TRINIMG.nbh and copy it to the root folder of your miniSD card.
3. With miniSD card inserted on the phone, start the bootloader (hold Power button on right side and Camera button at same time and stick with stylus in RESET on bottom).
4. You should see the screen pictured on the left, confirm flashing on screen by pressing the power button.
5. Flashing might hang after some time but this is normal. Just wait. Complete flash takes about 30 minutes, so check your battery or connect to charger before the flashing process starts.
6. When flashing completes soft-reset your device.
and you will flash and unbrick trinity bat this only work if you install before this hard spl i mean cid unlock trinity. if not you must fix usb port.
That will work? I hope so
Ok then i'll try flashing using that rom. Oo, i have install hardspl btw and so far flashing using sdcard method no probs. But after i bricked my trin flashing doesnt smooth like be4. Always gave me error 0018003 update fail on the halfway, i guess because i have bad nand on trin and probably cuz cooked rom.
Can u give me another link, perhaps on xda ftp. rapids so slow 4 me. Btw i have download dopodasiawwe official rom on xda ftp *twice but still when i tried to run the package it gave me corrupt archive integrity fail w!f.
Thanks gsmhackerns, i downloading the package now!
Perhaps you can find a way to make a goldcard for Trinity?
See http://forum.xda-developers.com/showthread.php?t=437996
That's what i looking for! Thanks.
Humm, superb. Yay, great! Thank you stepw. Even its for elf with a little mod i hope this will work. Once again thank you.
Stepw, i have tried making the gold card, everything went ok. I have temp. cid *supercid* but the probs now is i can't download http://rapidshare.com/files/21174752/RUU_Trinity_HTC_WWE_1.15.405.5_6275_1.20.00.11_12201_Ship.execan someone uploaded to somewhere else. Rapidshare crap! perhaps on xda ftp.
thanks!
goldcard cannot help in such a situation.
I can however make an SSPL that loads off SD card - just like for kaiser you will be able to use it because you are already on hardspl.
then that will allow you to flash stock SPL.
PM me and send your MSN address, so we can test it out. if it works i'll post it in this thread too in case others get stuck also
cmonex said:
goldcard cannot help in such a situation.
I can however make an SSPL that loads off SD card - just like for kaiser you will be able to use it because you are already on hardspl.
then that will allow you to flash stock SPL.
PM me and send your MSN address, so we can test it out. if it works i'll post it in this thread too in case others get stuck also
Click to expand...
Click to collapse
Indeed. Youre right cmonex, it doesnt make any difference at all 4 my trin. After several tried using and making goldcard 4 trin, finally i made working goldcard4trin, but gosh it still stuck when i tried to update the os (update os fail) humm anyone.
Sorry for wasting your time with Goldcard, I have overlooked that you have a hard spl on your Trinity. In this case goldcard doesn't make a lot of difference.
And there's no trindiag.nb to the best of my knowledge that could be used instead of SSPL cmonex is suggesting to run from SD.
Back to the topic, sounds like you have some "bad" blocks in flash and OS can't be flashed. Bad blocks can be reset with "task 2a" command, see this thread for more details:
http://forum.xda-developers.com/showthread.php?t=330496
The question is how to run it without USB and I don't have an answer for you
Some people have previously mentioned they managed to flash smaller OS images when larger images failed, perhaps if you try flashing some minimal vanilla ROM, it will succeed?
Bad NAND, Yup!
Ya... as i mention before yup i do have bad nand block on my devices. Using manila rom with smaller img size the flash went 'OK'. But it doesn't boot at all infact just black screen with green led on.
Okay the only solution probably use mtty and do task 2a if i'm not mistaken. But like you said "The problem is the USB port". I think the port is ok cuz i already tested it connecting my usb to my trin without inserting the battery and the red led *magenta* is on. humm, weird!
But if something can make it working without involving any pc connection it would be a great achievement. hahah! well i supposed i have to put my trin on bunker before someone can make it happens
I asked SEA in my country and they recommend me to changed the machine it self and they charge me around US $160 ho...ho.. too "wideeeeee" for college boy like me
Same problem, i flashed the rom
RUU_Trinity_DOPODASIA_WWE_3.00.707.18_6275_1.46.30.11_108_Ship
and after that i tried to flash a new radio!
power+cam and the cell phone did not show usb, then i used sspl to rum the radio but it locked at 0%
after that it is stucked at bootloader screen
ipl 1.0
spl 3.20 .....
but no usb and no sd card !!
did i lost the cell phone?
there is no jtag ou something like that ?
so now... you still want this SSPL? i'm thinking of patching one up to automatically run task 2a maybe. or just restore stock spl for warranty service if that's what you have in mind. but you didn't really reply to that offer?
Please if you could build a sspl for this condition it would be enough because once sspl i can run a new ruu with hard-spl again ! the problem i believe was caused becaus this original rom's have a spl.nb inside , in the screen we read teh information about the olipro spl but i thing teh original spl.nb messed up the hard spl!
There is another problem, i formated to fat32 my card and put a TRINIMG.nbh of a rom inside and he did nothing!! same card in elf with ELFIMG.nbh of a rom runs great!!
It means that this spl of mine will not flash from card? goldcar would help?
and cant i flash something in serial ? like a jtag or something?
Anyhelp will be more than apreciated!
sorry the bad english
Needed!
Cmonex, sorry for longtime haven't seeing this thread again. okay i really need your help btw if you willing to help me. The spl your talking about perhaps can sort out the probs (i hope) at least we tried. as for task2a cmd to clear the bad nand block is none usefull for me since usb conn. are definitely drop dead.
how about patch the SSPL to do task2a cmd to solve the bad NAND block first.
dinizbruno said:
Please if you could build a sspl for this condition it would be enough because once sspl i can run a new ruu with hard-spl again ! the problem i believe was caused becaus this original rom's have a spl.nb inside , in the screen we read teh information about the olipro spl but i thing teh original spl.nb messed up the hard spl!
There is another problem, i formated to fat32 my card and put a TRINIMG.nbh of a rom inside and he did nothing!! same card in elf with ELFIMG.nbh of a rom runs great!!
It means that this spl of mine will not flash from card? goldcar would help?
and cant i flash something in serial ? like a jtag or something?
Anyhelp will be more than apreciated!
sorry the bad english
Click to expand...
Click to collapse
no usb, no sd, no chance sorry. jtag it or get it serviced or get another phone.
as for jtag, hermes jtag has been worked out by scholbert. trinity is probably the same, but you will have to find the pins. the rest of the process will be the same.
Dear all,
I can't go to bootloader screen ..fff before I had on my trinity faman 4.03 rom and I would change with the NiAX rom... after 3% restart and I think that my phone brick and my phone stay on htc screen fff please help
I have windows vista and even if i follow all steps pfff it changes nothing...after hard reset ...fff please help ...
I think my trinity is out :-(????????????????????????
Please help,
The O.S is more important to these operations than can be stressed - for a 99% safe flash Win XP is your best bet , I have had nothing but error 260,270 halfway flashed roms and usb faults running on vista and since I had my original bricking episode - NOTHING , I repeat NOTHING including genuine roms has flashed without a recovery or at least without doing something strange in the process - SPLXPLOIT has been a saviour here , without it I would've been lost.
Cant the O.P simply use another machine to test out the USB theory ?
ALIVE AGAINnnnnnnnnnnnn!!!!!!!!
My p3600 was stucked att bootloader, and wont give "usb" and do not read TINIMG.NBH (tried on elf with ELFIMG.nbh and the card was great)!
I did a golcard with the post on elf about it and the cell with the gold card inside was the same, no trinimg.nbh and no usb.............
BUT..............
with the goldcard inside, turned OFF, i placed it on the usb cable off the pc and the device booted to the bootloader screen, but this time he got "USB" , before flashing anything i removed the card , and putted switched off in the usb, booted with "serial" with card and pressing power and then placing usb still "serial" message!
I putted the card, did not switched on , placed on the usb and waited for it to boot for it self , and for my surprise "usb".
Flashed stock rom, and it booted nice!!!
Please try!
saved my day!
sidekraouf95 said:
Dear all,
I can't go to bootloader screen ..fff before I had on my trinity faman 4.03 rom and I would change with the NiAX rom... after 3% restart and I think that my phone brick and my phone stay on htc screen fff please help
I have windows vista and even if i follow all steps pfff it changes nothing...after hard reset ...fff please help ...
I think my trinity is out :-(????????????????????????
Please help,
Click to expand...
Click to collapse
I have to know how to repair my phone please... nobody can explain precisely how to put my phone on bootloader using my sd card directly from my computer under vista...???
After flashing the rom for WM 6.1 with error flashing, my P3600i bricked and could not load into window mobile, there is error 270 when installation the hard spl or any cooked rom. And check by the softawre mtty with command task 32, the cid level become FF, so I could not flash any rom because it is not supercid.
First, I need to clarify that, the P3600 not equal to P3600i, so the unbrick method of P3600 could not apply for the P3600i.
After reading many messages from forum xda, it is know that the P3600 could use the splxploit to unbrick the P3600, it is a easy way for P3600 to unbrick and then install other WM rom. However, because the rom size is different, the splxploit could not make the P3600i unbrick.
It is know that another method is using the mini SD card with fat 32 format, and Rename the .NBH file to TRINIMG.nbh and copy it to the root folder of your miniSD card, then go to the engineer mode for flashing, however, I think that this method is flashing like using the USB connect PC, and for the P3600, could find the official rom to solve the bricked problem.
Finally, I found the gold card solution from the page http://wiki.xda-developers.com/index.php?pagename=Elf_GoldCard
, this may be the solution to unbrick the P3600i, it is because it is making the ppc become a supercid, so you have the right to flash another rom, but this is still very complex for other models p3600i to try it.
For the conclusion, there is still not brilliant method to unbrick the P3600i except the senior member that have their professional method. Eg. Flashing the rom with other equipment directly. I think there is only two methods for me to unbrick the P3600i, but I still could not do it.
1. Flashing the official rom for your p3600i the level is "CID", only could install with the official rom. But I could not find any HTC official rom for for P3600i. You need to find the official rom that match with your P3600i, and then you could flash it in the engineer mode or mini SD card method.
2. To cheat the internal OS, making the "CID" level to "SUPERCID", like using the gold card method to unbrick and then install another rom, but this method is still very complicated for P3600i.
3. Wait.......
Futhermore, I have tried the SD card flashing method, format the SD card to fat 32 and tried to flash the p3600i with the official rom, which not same as the CID. The result is failed, so for the conclusion, the SD card flashing method same as flashing the rom from the computer, it is just using another method to flash only.
For the gold card method, I have tried to make the gold card which could jump over the CID check by the SD card, I am following the procedure of the ELF gold card, with the software of QMAT,however, when I generate the HTC gold card for my bricked device's key of trinity, the QMAT software auto shut down, so I could not generate the HTC gold card, I have tried to generate the HTC gold card for Elfin, that's is OK, but I could not use the sd card to boot my device to supercid. And finally, I could not success to flash the rom.
Finally, I have asked the HTC support to provide me the official rom because they haven't released it. They told me that the rom could not give me because this is the original rom and not the update rom, so could not give me, and suggest me send back to HTC for checking. So
I send back the p3600i to the HTC service center for checking and repair, because they have the official rom for my device CID: HTC__601, I think they just flash the device with the HTC official rom, then the device is unbricked. However, the result is very disappointed, they tell me that I need to replace the mainboard for the device to work again, because out of warranty, the price of change mainboard is very expensive (could buy another new model), I argued with them about why the fail of flashing rom, is software the problem, need to change the mainboard, they said this is the only solution to solve the problem, so I rejected their suggestion and got back my bricked P3600i.
I can only to wait for the soultion about how to unbrick the P3600i now.
Waitng the expert to
1. making splxploit for p3600i (because p3600i is 256 Mb rom)
2. the goldcard method, it is difficult to borrow the wm device from other because I dont know there is any risk for the wm
I don't know if I can help you but will try since this forum has helped me.
My P3600 is basically screwed. It's a walking zombie brick phone.
Why zombie? Because I bring it back from the dead everytime!
I dropped my phone quite badly twice in a day a few days back,
Next day I woke up... my pocket alarm had hung and I had to hard reset because a soft reset brought about the Tri-colored bootloader screen.
After that, everything was GONE... so I decided I might as well load a new up-to-date ROM. Was using Akeo's rom happily before that.
Did the usual SPL routine, new radio, new OS rom.
Installed new stuff...
But then phone would continually enter bootloader screen most of the time when I did a soft-reset. Except that it would have a terrible error message that only gave me the option of trying to restart without changes or basically reset everything to original settings (or something like that which meant everything is gone again). With the error message in place... nothing would work.
Could not reset into normal bootloader. (without the error message)
Windows mtty.exe method could not connect. (it would under normal bootloader)
Activesync was obviously disabledsync.
Flashed radio, spl and OS roms repeatedly using Des' SSPL and Olio's HardSPL 1.20 and 1.30 to no effect. It would always come back with that error on a random reset.
Then I read about the method of flashing with SD card. But this didn't solve my problem... it would come back still after a reset.
Mtty.exe from Windows XP to format nand and mark bad blocks etc.
Nothing found.
Finally, I almost gave up.
Then out of desperate measure.
I decided to leave a copy of a TRINIMG.nbh in the SDcard for GOOD!
It's basically an SPL image. Done with the NBHutil.
Used it to split out the HardSPL 1.30 spl.nb and merged it with the splash.nb and sub-splash.nb from my current OS rom.
Everytime I reset... there's still a chance it will enter bootloader mode with that horrible error message. But in such a situation... I now simply choose not to reset settings to default and instead simply pull out the battery.
Then plug it back in and power it on again. 80% of the time... it boots back into Windows mobile like normal on the first try! No loss of settings... nothing nasty. Back to normal! The other 20% of the time? I just pull out the battery and power it on more times! Till it works! Hasn't failed me yet in 5 days. Mind you, I was bricking it twice a day before this. That's progress!
I simply use SPL backup to make a full backup anyway whenever I install any new software etc, contacts etc.
Give it a shot.
I don't know why it worked for me...
Maybe I have bad sectors or something where the SPL is.
Whatever it is... the SDcard's TRINIMG.nbh works as my SPL now.
Think of it as a case of a bad bootup sequence on an old dos system needing a backup msdos bootdisk to do the trick!
Good luck!
Hard SPL 1.30 should be SuperCID and having that boot from SDcard may resolve your flashing issues. IF IT WORKS!
Thank you for your experience, I will try your method later!
"
I decided to leave a copy of a TRINIMG.nbh in the SDcard for GOOD!
It's basically an SPL image. Done with the NBHutil.
Used it to split out the HardSPL 1.30 spl.nb and merged it with the splash.nb and sub-splash.nb from my current OS rom.
"
I did not try another method because I have borrowed my P3600i for my friend to help me unbricked. And finally, he was done.
My friend tell me, he is trying the old official rom of P3600, he tells me that he dumps from his P3600, I dont know how he dumps and then he is using the hex editor to MODIFY (HEX EDIT) the ROM FOR THE P3600i. You could refer to this page for the modify method
"http://forum.xda-developers.com/showthread.php?t=399779". And finally could success to flash the rom.
I think for the P3600i user, you could try the official rom of P3600, of the same location, for modifying the rom size, and then try to flash the bricked p3600i.
Now I could install the hardspl and try another cooked rom again.
Thank the help of my friend.
OK. Decided to upload a new ROM as my phone was getting slow and unusable.
It's an O2 XDA (Touch Diamond) with:
Touchflo v3 Build 29946
ROM 1.93.206.6 WWE
09/08/08
Radio 1.00.25.05
Protocol 52.29.25.12H
Boot R1.00.25.05
I downloaded Olinex's unsigned developer Hard SPL and I extracted the NBH file and renamed it DIAMIMG.NBH following the advice here:
http://forum.xda-developers.com/showpost.php?p=2707841&postcount=4035
On soft reset I pushed the vol down and back buttons to get the boot loader stripes, then let go.
I now have a screen which says "Loading..." and has done for 20 minutes. I have now got the phone on charge while I wait for some help to see what to do next, just in case this is a critical stage - don't want to brick it.
Reading through again I am concerned that this was a procedure for rom upgrade not Hard SPL install, can someone tell me please?
Thanks in advance for any help.
Well, I ended up taking the battery off to get it to reboot. It seems to boot fine back into the old ROM.
I still intend to upgrade it (to SwiftBL's v7.5) but have a few questions:
1. Can the HardSPL be run from the internal storage card? If so is it simply running the exe from the unpacked zip from within a folder? ActiveSync is a bit too flaky for me.
2. Do I need the SIM card in the phone at any stage of the ROM upgrade?
3. On the original ROM I get a drop down menu to setup the phone to the UK O2 network settings. If I load a new ROM, will I need to know these settings?
Cheers
1. HardSPL cannot be run from storage. Only Activesync or Bootloader
2. No. You can flash without SIM card
3. You can use connection setup on any new ROM. Usually starts straight after initial setup.
OK here's where I'm at now.
Downloaded jockyw2001's HardSPL 1.24
Ran it and it got as far as prompting me to run on the phone. I said 'Yes' and the HTC screen went black as expected.
Next stage was to run the DiamondCustomRUU.exe file which I did but this is waiting for ActiveSync. ActiveSync will not sync with the phone now, I guess because the phone is not 'on'?
Where do I go from here?
Use the Hard-SPL in my sig with your RUU.
Thanks, will do (it's not the one mentioned in the ROM author's description though).
So how do I recover the phone from the black screen now? Is it safe to remove the battery to reset?
Battery pulled after reading this post:
http://forum.xda-developers.com/archive/index.php/t-427945.html
I'll try the SPL you mentioned now.....
Had a good search but can't find out. This Olinex zip contains just one file RUU_Signed.nbh.
Where do I get the other files from to run this?
use the attached . It has the RUU exe and the nbh.
Thanks. This is a signed version I see, was going to use SwiftBL's ROM which requires unsigned.
May take a look at other roms that use signed unless you think that I can load the SwiftBL rom with this version?
question;
i've got a mda vario III aka htc tytn II (Kaiser) which cannot make an usb Active sync connection. the usb connector seems not really fine, it charges over usb
BUT in bootloader menu i get an usb connected message even if i do not have an usb cable connected. so my usb connector will be shot i think
what do i want to accomplish:
i need to change the language from german (german htc rom installed) to the either the WWE or NLD htc rom.
i downloaded both original htc roms, but i need to flash it via micro sd since i do not have a working AS connection. i have hardspl installed, and i think the previous owner sim and cid unlocked it. but i do not know for sure and cannot test it because i cannot run the unlocker program again! (it had hardspl on it, and it is sim unlocked. so i believe it is cidunlocked too?)
but if i extract the image i get amongst others 'RUU_signed.nbh'. i can rename that to KAISER.NBH (or something like that) and if i put that on my microsd card it 'might' just install the original htc rom back. but, will the hardspl that i have flashed be gone also! i only want it to update the radio rom and os, not off course overwrit my hardspl. since that is the only way to flash the device, i cannot risk loosing the hardspl.