Cannot Flash the ROM on my Kaiser!?! - Tilt, TyTN II, MDA Vario III Themes and Apps

Ok heres the story,
Sold my phone on Fleabay, however want to unlock it from its grips of T-Mobile.
Before you ask i have had about 3 different WM phones all of them i have flashed..
Now with this phone everything is abit different?!? i install Hard SPL... Well it gets to the 3 colour screen goes to USB then will go to the progress bar sit for a while and then i will recive a connection problem...
Now i have tried unplugging the usb at this point and putting it back in at the 3 colours... i have done the same but disabled usb connection in active sync.. i then thought if im getting this boot loader it must be installed?!?
tried installing a rom same error.....
i then thought maybe its all communication going to phone.... it active syncs fine etc.... it even updates with the new t-mobile rom.... everything else is not communicating .... someone please help im about to throw it out the window??!?

xda_kerby said:
Ok heres the story,
Sold my phone on Fleabay, however want to unlock it from its grips of T-Mobile.
Before you ask i have had about 3 different WM phones all of them i have flashed..
Now with this phone everything is abit different?!? i install Hard SPL... Well it gets to the 3 colour screen goes to USB then will go to the progress bar sit for a while and then i will recive a connection problem...
Now i have tried unplugging the usb at this point and putting it back in at the 3 colours... i have done the same but disabled usb connection in active sync.. i then thought if im getting this boot loader it must be installed?!?
tried installing a rom same error.....
i then thought maybe its all communication going to phone.... it active syncs fine etc.... it even updates with the new t-mobile rom.... everything else is not communicating .... someone please help im about to throw it out the window??!?
Click to expand...
Click to collapse
What does it say on the bootloader screen ? Is it unlocked and flashed with Hard Spl,? If so try and flash it from an SD card.

Related

Problems Updating ROM

Hello everyone,
I have problems updating my SPV M3000. I've been tryin' it for a month now but it just won't happen. Every Rom i download i get the same problem: I just follow the steps of the wizard. But when the installation begins, my device's screen flickers and then it looks like it starts to glow. At the same time my activesync connection drops. The PC gives the [ERROR 260] this makes sense because i lost the connection. Then i have to soft reset my phone. I have Sim and CID Unlocked the phone.
My current version is 1.3.1.13.
Can somebody please help me.
thnx,
Dennis
have you tried changing your use cable? Seems like it's the source of the trouble...
dbleliev said:
Hello everyone,
I have problems updating my SPV M3000. I've been tryin' it for a month now but it just won't happen. Every Rom i download i get the same problem: I just follow the steps of the wizard. But when the installation begins, my device's screen flickers and then it looks like it starts to glow. At the same time my activesync connection drops. The PC gives the [ERROR 260] this makes sense because i lost the connection. Then i have to soft reset my phone. I have Sim and CID Unlocked the phone.
My current version is 1.3.1.13.
Can somebody please help me.
thnx,
Dennis
Click to expand...
Click to collapse
Have you tried flashing an "official" 2.xx rom?
--M
I did all of that... but still no succes.... Anybody have other solutions??
Thnx
Did you ever get your issue resolved?
I've got the same problem and I've tested my MDA with two seperate USB sync cables. Both sync with ActiveSync and actually transfer data with no issues, but I get the 260 error EVERY time.
Does anyone know if there is a MS service that needs to be running that maybe we're missing? I thought all of mine were, but might not be.
Any updated info would be WONDERFUL.
Read this, at the bottom of the file are the error-codes and try to use another USB-port (preffering at the BACK! of your PC)
ftp://xda:[email protected]/Wizard/Roms/ROM/Update Utility Readme.rtf
nabibakhur said:
Did you ever get your issue resolved?
I've got the same problem and I've tested my MDA with two seperate USB sync cables. Both sync with ActiveSync and actually transfer data with no issues, but I get the 260 error EVERY time.
Does anyone know if there is a MS service that needs to be running that maybe we're missing? I thought all of mine were, but might not be.
Any updated info would be WONDERFUL.
Click to expand...
Click to collapse
Maybe try to use activesync 2,5 beta.
Actually, I have the most recent ActiveSync beta and all. And that nice ftp link doesn't work, which I've noticed seems to be the case most of the time.
Can I download that file elsewhere?
I've actually plugged the USB cable in every USB port I have to test that theory and still no-go.
I'm currently on the phone with T-Mobile PDA Tech Support ( BLECH! KILL ME NOW! )
If I get a solution I'll post it and a walkthrough on how to fix it.
Ok, so, just got off the phone with the T-Mobile PDA Tech Support people and here's the lowdown...
It's the phone itself. Somehow my phone is bugged, go figure. Sorry to break the news to the guy who started this thread, but hey, I'm getting a free T-Mobile Dash out of it

Bootloader screen goes grey.....

I have a G3 wizard. I was stupid and trying to go from button's ROM to Crossbow reloaded. The flash ended up crashing somewhere in the 80% range. Now my wizard will rarely get into bootloader mode. I'm leaving the battery out for 5 minutes at a time. When I put it back in it will go into bootloader mode until I plug the USB cable in it and try to flash it the screen comes goes grey and I get a 260 update error..
I really hope I didn't brick this thing, It's my only connection and I have some important new job related calls to make!
mine is stuck on the flash screen
i have a g3 wizard and today it would not get past the windows mobile 6 professional splash screen (tnt rom). is there anything i can do. i tried reflash it but could not establish a connection. please help
tarusdg said:
i have a g3 wizard and today it would not get past the windows mobile 6 professional splash screen (tnt rom). is there anything i can do. i tried reflash it but could not establish a connection. please help
Click to expand...
Click to collapse
Try holding the camera button while powering it on. Then put in the usb cable and flash away.
tarusdg said:
i have a g3 wizard and today it would not get past the windows mobile 6 professional splash screen (tnt rom). is there anything i can do. i tried reflash it but could not establish a connection. please help
Click to expand...
Click to collapse
Do a Soft reset of the phone,if it works out,fine,otherwise do the Hard reset,although you might lose your personal data but phone will work out.
If both do nothing and it still gets stuck,then there's no other way except to reflash.
Which connectivity your not getting,If you are saying about Activesync connectivity,then you don't need Activesync connectivity to flash,get your phone into Bootloaders(multicolor screen) connect it to your pc via usb cable,when usb appears at the bottom of the bootloadermode,flash the Rom.
But if you cannot establish connectivity through usb cable,then either your usb cable is faulty or the mini usb port of the phone is damaged.
Looks like i've been threadjacked...can anyone help?

Stuck after ROM flash:error 206

I decided to reflash my wizard after it continually getting slower and slower after a year. I haven't done it in awhile. It is already unlocked. I flashed the 1.05 rom and it was working. I was going to go up in steps ending with the touch rom. I flashed the wrong rom evidently and now am downgraded to 1.01 on spl/ipl and os 2.26.10.2. The wizard won't activate Activesync and I can't get any communication. I tried rebooting the pc and the wizard multiple times. Still nothing. Need something quick to fix this. Everytime I tried to launch a rom flash I get an error 206.
digitalmayhem said:
I decided to reflash my wizard after it continually getting slower and slower after a year. I haven't done it in awhile. It is already unlocked. I flashed the 1.05 rom and it was working. I was going to go up in steps ending with the touch rom. I flashed the wrong rom evidently and now am downgraded to 1.01 on spl/ipl and os 2.26.10.2. The wizard won't activate Activesync and I can't get any communication. I tried rebooting the pc and the wizard multiple times. Still nothing. Need something quick to fix this. Everytime I tried to launch a rom flash I get an error 206.
Click to expand...
Click to collapse
If it was already CID unlocked,there was no need to downgrade again 1.05,once CID unlocked will remain unlocked forever,unless you intentionally don't flash back the locking code back on to it.
Now try to get into Bootloaders (multicolor screen) hook up the phone with pc via usb cable and check small usb appear at the bottom of the bootloaders,if it appears then download the official stock rom and flash to recover back to the default status,then download the WST 4.2.2 tool and run the 'CID Action' button to verify the CID lock/unlock status of the phone.if its still CID unlocked then upgrade to any wm6 rom of your choice,otherwise perform the unlocking method again.If the usb doesn't appear,then you have a connectivity problem,check the usb cable or the mini usb port of the phone is faulty.Assuming you are doing on winXP.
"and check small usb appear at the bottom of the bootloaders..."
I don't understand what your talking about when you say bootloader. The bootloader is the ROM installation program is it not. How do you check an icon in that? If you mean system trays on the PC or PDA, no USB icon shows. I got no radio or sync services working. The OS is corrupted and operates extremely slow. I can't get any kind of communication between the PDA and PC. Not even through windows explorer (running XP). It's not the cable, I just used it to downgrade to 1.05 and it was working fine. It wasn't until I tried to upgrade to back up, and selected the wrong ROM off my USB storage, that it flashed the wrong ROM and caused all this. Mostly because I hate trying to remember what the longs string of digits mean on each ROM. Especially after I haven't looked at all the files and haven't done a flash in a year.
So no communication. That's the issue.
So does anyone else have any info? As I stated, I can't get any communication between the MDA and the PC. So I don't know how I can flash a stable ROM.
I repeat again,Get the phone in Bootloaders mode (multicolor screen) by pressing and keep holding down the camera button and at the same time either 'Soft Reset' or 'Power On' the phone,but keep holding down the camera button,till phone boots up in Bootloaders mode(multicolor screen),hook up the phone with pc via usb cable and check if small usb appears "At the bottom of the Bootloaders Screen" and not in the system tray of the pc. If it appears then follow the advise I gave you in my above post,but if doesn't appear then you have a connectivity problem.
digitalmayhem said:
"and check small usb appear at the bottom of the bootloaders..."
I don't understand what your talking about when you say bootloader.
Click to expand...
Click to collapse
The Wiki as all the (basic) info to get you started.
It doesn't work
I can get into Bootloaders mode with usb at the bottom. BUT, I can't get any connection to ActiveSync, any of the ROM update utilities and no radio network connections. That was the specific thing I'm telling you. If the Desktop and the PDA won't talk to each other, what am I gonna do? It's not the cable either. The Wizard Tool will not pick it up either when I used it to try to get device info. If your going suggest any kind of ROM or software off the forum, please specify exact version and title so I don't have to go through 100+ pages doing a search to find a specific piece of software off a vague title such as "stock ROM". You may know what it means because your always on the forum. When someone hasn't been back here in awhile they aren't going to remember some arbitrary string of numbers and letters indicating a certain ROM that they haven't used for a year. Too many of you "regulars" get all pissy about things when someone asks a question. If someone keeps asking the same questions, it's because the forum is NOT laid out in an easily searchable fashion unless you have specific search criteria for things such as CUSTOM_RUU_Wizard_1050412_WWE_10111210_WWE instead of "stock ROM".
Have you read the Wiki?
http://wiki.xda-developers.com/index.php?pagename=Wizard Windows Mobile 6 for newbies
Or other posts?
You'd know by now that in bootloader mode ActiveSync or any other tool (that uses ActiveSync) can't communicate with the phone but that it's possible to upgrade a ROM using the official upgrade utilities.
Have you tried making a search and getting hundreds of undesired and repeated posts which makes you lose days searching for a specific thing?
If you'd been here as long as many of us you'd also be tired of people asking same questions. I was once a fresh member and i would always 'waste' my time than others'.
Also the forum search feature has been enhanced by using Google's search engine instead of internal.
There is simply no way I can express my deep and sincere gratitude for the information available in this forum. Let me explain and I think you may understand why.
Several days ago my wife and I received a couple of HTC 8125's from Ebay. Being a tinkerer I wanted to see what I could do so I upgraded mine to Mobile 6 with Touch-Flo.
The wife was skeptical and waited to see how it worked out. Of course she eventually decided to go for the Bling and handed me hers to upgrade as well.
As soon as the upgrade started on hers the pda went bootscreen and locked up. Sooooo I'm sweating bullets and searching the forums as fast as I can go before she finds out. Then I find this thread and the last post... Don't need Activesync to update as long as the device pops up a little usb on the screen when you plug up... I flashed the 8125 upgrade and *Bang*! Back in business. Continued the upgrade and all is well. The wife is now walking around with her "Bling" and happy and I am off the hook!
Thanks for the GREAT FORUM!
Rowdyone said:
There is simply no way I can express my deep and sincere gratitude for the information available in this forum. Let me explain and I think you may understand why.
Several days ago my wife and I received a couple of HTC 8125's from Ebay. Being a tinkerer I wanted to see what I could do so I upgraded mine to Mobile 6 with Touch-Flo.
The wife was skeptical and waited to see how it worked out. Of course she eventually decided to go for the Bling and handed me hers to upgrade as well.
As soon as the upgrade started on hers the pda went bootscreen and locked up. Sooooo I'm sweating bullets and searching the forums as fast as I can go before she finds out. Then I find this thread and the last post... Don't need Activesync to update as long as the device pops up a little usb on the screen when you plug up... I flashed the 8125 upgrade and *Bang*! Back in business. Continued the upgrade and all is well. The wife is now walking around with her "Bling" and happy and I am off the hook!
Thanks for the GREAT FORUM!
Click to expand...
Click to collapse
Thankz !
We all highly appreciate it,glad you got it working .Thats what this Forum is sooo famous for "Help & Care"

A quick question about Connection settings in ROM's - are they regional?

Hi there,
Sorry if this a retarded question, I can't find anyone else that's asked.
Basically my unbranded Touch Pro 2 has in the data connection settings the default selections of UK and then TMobile.
What i need to know is, on these cooked ROMs will that setting still be there? If not where do i get the settings to reenable my data.
I'm going to do the HardSPL and flash thing tonight for first time. I'm a little aprehensiveso just wanna make sure I don't install some flashy ROM but lose my 3G browsing.
Thanks to whoever can set my mind at rest.
I have an unbranded tp2 on tmobile uk from expansys, connection settings with custom roms bring up tmobile uk. It did when i was flashing Kaiser roms.
Having trouble at the mo with mms on the current rom I've flashed but gonna do a bit of searching tonight to sort that.
(need to update my sig from kaiser to tp2)
cool, good to know someone else with sam setup. mine is from mobilephonesdirect.
I don't send a lot of mms, but what is the known issue?
Also were there any complications for you or a smooth install and Hardspl flash?
cheers
I think maybe we should take this to pm to keep the forum uncluttered? check your inbox.
@dazkeirle
My unbranded TP2's on T-Mobile and from MobilePhonesDirect too!
OK I was all up for flashing last night (HardSPL) but lost my bottle when i came to something which was not mentioned.
When i first started tot run the program, with my phone in an activsync connection everything was normal.
Then when i click Automatic flash, then ok on the next screen (before the screen with the picture of the TP2 on it) my TP2 goes into a kind of dead mode, black screen no lights.
Now i think this is normal from what I've read, but the weird thing is my computer indicates here that the USB is dropped and activsync disconnects, however some other drivers are then installed and the phone is sort of still connected (although that isnt indicated anywhere).
I was nervous as activsync was not there so hit cancel, did a soft reset on phone and all was still normal (preflashed state).
Please can somebody confirm that activsync only is there at the start and that the activsync will disconnect after you hit ok, it's not explicitly defined in the tutorial and I'm nervous of bricking handset.
Thanks
Click to expand...
Click to collapse
moved to newbie thread as bound to get better response there.

[Q] Trying to unbrick Kaiser

Hi All,
I've been running the Orange (UK) WM6.1 ROM for months/years without problems and was messing around with some texts and somewhere along the line I have ended up with the standard 4 stripes down the screen and some text top left.
I have scanned the forums here and the wiki and they suggest connecting using USB and running Mtty.exe, however whilst I can connect the phone using USB Activesync won't recognise it and then I get an error from Mtty.exe because it won't recognise the phone.
I have also tried re-intalling the Orange ROM as well as newer roms, but none of them seem to be able to connect to the phone.
Active sync doesn't seem to be able to connect on Win 7 or Win XP despite them syncing fine this morning.
So, any suggestions out there?
I'll do some more searching, but any pointers would be appreciated.
Thanks.
Try a new USB cable, I went through 5 in one year, or try flashing via SD card.
Well I tried a couple of different leads and no luck.
I did manage to get some info from mtty.exe, but didn't make sense.
I took my SIM out to use in another phone and having left the battery out for a while, put it back in to try again at getting it to start and it booted fine without any problems.
After a bit of messing around it seems like that the boot problem is either down to a problem with the SD card, SIM or a foreign object in phones casing.
I keep the phone in a pocket of my overals that I use a workshop and occasionally iron filings from a grinder can get into it's working, which is what I think has happened.
ANyway, it's back and working again, only need to keep it going until Orange can get some Desire HDs in
Hi!
Read those threads again,the solution is there.
1.Disable USB connections in Activesync menu (right click on green icon on the tray)-->connection settings-->untick "Allow USB connections"
2.Put your device in bootloader mode (yours is in it)
3.Start to connect it with MTTY to do what you want or just run an official Orange UK ROM update
If everything is fine,your device will be alive again.
After that install Hard-SPL to avoid problems like this.
BR
Scootie
P.S.:Sorry,I didn't read post #3,but it can be useful later.
One more tip:check the camera button.
Thanks Scootie,
I'll try the Hard-SPL thing - the jumping into boot loader seems pretty random, has happened a couple more times and I find I have to pull the battery for several minutes and then try a restart.
The camera button doesn't seem to do much other than what it is supposed to.
Pretty annoying since I have had the phone for 3 years, but have not had signal at home so hardly use it, and now we have signal due to Orange/T-Mobile merger from the beginning of the month the phone fails me :-(

Categories

Resources