Hi,
I have an att tilt (8925). The other day I happend to upgrade the ROM or flash from 6.0 to 6.1 from htc official site there after the phone doesn't get the signal(wireless).
The following is the device information.
ROM Version:3.57.502.2 WWE
ROM Date:07/17/08
Radio Version:1.65.21.18
Protocol Version:25.88.40.05H
Please any kind of help would be really greatly appreciated....
Thanks in advance.
And you used the ATT rom?
Thanks for the reply but I am sorry I am totally new to all this wat do u wat me to do....
yeah looks like you did.
Could you give us more data ?
Where did you find your phone ? Was it unlocked ? Did you do hard-SPL in it ?
What is the OS version, exactly ?
Maybe you must change the Radio, maybe you must flash with another ROM version.
Maybe you only must enable the phone...
Please enter the boot screen and write here all your data numbers (then, switch off the device, you'll boot normally again), and also write all the data you can find in Start-Settings-System-"Device data" (or similar the last screen)
(don't write here the IMEI as it's not needed and could be used for third party people to lock your phone) !!!!!!!!
With all the data we'll know what exactly is your device and what exactly may be happeing to it.
Hi,
I got the phone from ATT with windows mobile 6.1 Professional.
R 1.65.21.18
G 25.88.40.05h
D 3.57.00.00
These are the things that I got when I tried to reboot the phone
ROM Version:3.57.502.2 WWE
ROM Date:07/17/08
Radio Version:1.65.21.18
Protocol Version:25.88.40.05H
and this is the data from the device
Please help me,Any replies would be greatly appreciated.
thanks in advance.
Which is it?
srinivasmuthyala38 said:
I got the phone from ATT with windows mobile 6.1 Professional.
Click to expand...
Click to collapse
However earlier (in the first post)
srinivasmuthyala38 said:
The other day I happend to upgrade the ROM or flash from 6.0 to 6.1
Click to expand...
Click to collapse
I'm
What actually happened and why the difference? Surely if you have an AT&T phone and put an AT&T ROM on it (with no other modifications) as per how AT&T intended, if that causes it to fail, AT&Ts warranty department should be informed and should come to the rescue? If you've already hard reset the phone and tested again (it's important to hard reset after a ROM flash) and have tried reflashing the new ROM again and hard resetting afterwards with the same results, it's time to contact them?
Flying Kiwi said:
However earlier (in the first post)
I'm
What actually happened and why the difference? Surely if you have an AT&T phone and put an AT&T ROM on it (with no other modifications) as per how AT&T intended, if that causes it to fail, AT&Ts warranty department should be informed and should come to the rescue? If you've already hard reset the phone and tested again (it's important to hard reset after a ROM flash) and have tried reflashing the new ROM again and hard resetting afterwards with the same results, it's time to contact them?
Click to expand...
Click to collapse
omg I should just shoot myself for saying this, BUT, yes this is very good advice.
Hi,
Thanks for the reply, I have tried wat u said but no result and unfortunately I am out of warranty I called HTC for a repair they it would cost $35 for diagnosis and minimum amount for the repair is $145 can u please suggest me any alternative for this.......
srinivasmuthyala38 said:
can u please suggest me any alternative for this.......
Click to expand...
Click to collapse
wat is the answer to my earlier question? You need to tell us wats really going on if we are to be any assistance.
Hi Flying Kiwi,
I have flashed the rom thats given by att and then hard reset aswell but that dint work out still no network.please let me know if I answered what you were asking.
Thanks
srinivasmuthyala38 said:
I have flashed the rom thats given by att and then hard reset aswell but that dint work out still no network.please let me know if I answered what you were asking.
Click to expand...
Click to collapse
Did you try this process twice (in case of a bad flash)? How do you explain the different Windows Mobile versions you referred to as being on the phone originally? How old is the phone?
Hi,
I tried that not twice but many times....I told you that I originally had win 6.0 then I updated to 6.1 given at htc.com its just out of warranty by a month, its like 13 months old.....
srinivasmuthyala38 said:
I told you that I originally had win 6.0 then I updated to 6.1 given at htc.com its just out of warranty by a month, its like 13 months old.....
Click to expand...
Click to collapse
The reason for my question was because in your 3rd post you said the device came with WM 6.1 from AT&T.... My HTC branded TyTN II had a warranty for 15 months from new and even if yours is just out of the warranty period for Tilts, they shouldn't completely ignore you if you can prove the problem was caused by using their ROM upgrade. That said, given no-one else with this phone and ROM has complained about the same issue as you here, either your local celltower has coincidentally failed at the same time as you carried out the flash or some damage has occurred to your device (such as to the aerial sticker perhaps). The simple way to find out would be to test it out in other areas where you know reception to be good, also to revert its ROM/Radio and SPL back to the original Tilt setup. You can find all the required files and instructions here at xda-dev via the wiki about how to do that.
As Flying Kiwi says, you can revert to 6.0...
I'm also intrigated by this change of versions from 6.0 to 6.1 (not WM versions but your posting versions)
Well, le'ts imagine you flashed the correct 6.1 ROM to the correct device (the data you wrote here allow us believe in this, I think, but I'm not an expert in SPL and radio versions). It should work. If not, you may try to download the old SPL and 6.0 ROM and flash them. (You'll find their links somewhere in the Wiki, here). Maybe you need to change the Radio to get the phone working ? Did you use the correct ROM for your S/N device ?
On the other side, you may try to do the entire Hard-SPL process and then flash one of this wonderfuls ROM's you may find here.
Or reverting to the original 6.0 and SPL "from" a cooked ROM ?
I'm thinking about my most terrible enemy, the electricity down, and thought you might download a bad version, or it got corrupted but you could flash it...
Please, don't follow my instructions till one of the masters will read my post and tell if I'm (or not) mistaken.
Hi All,
I thank you frm the bottom of my heart for all your responses, surprisingly when I when to att device support center today they said that my phone is still under warranty and they replaced my phone with a new one....
Thanks,
Srinivas
srinivasmuthyala38 said:
I when to att device support center today they said that my phone is still under warranty and they replaced my phone with a new one....
Click to expand...
Click to collapse
Glad you now have it sorted
Related
Dear friendly XDA-Developer,
Three days back, I tried to upgrade my ASIA IIs radio from 1.02 to 1.12. It all went smoothly, but however, my IIs had been without signal and all it says is No Service. I've tried to search through the forums, but to no avail. Kindly please help... I'm at my wits end.
Thank you all!!!
Not sure were or what files you used, if they were type I or II, so I would just sugesst that you Reflash using the files of wiki.
Hi, thanks! I practically tried all the other radio roms for BA thats available on the ftp://xda-developers, but all give same results... Is it something to do with the radio rom or my phone?
You can't try all roms of the download site for they wont work unless you know what you are doing, (correct rom type ect).
Just make your life easy and go over wiki, download, read and install, its worked for many before you.
Read below this
Dear MDAIIIUser,
Like what you've said, I've read through the wiki BA guide, over and over again. I've followed throught the tutorial carefully and still, it didn't solve my problem.
I've some queries here:-
Firstly, if I use an incompatible radio version, would it affect my XDA IIs? I mean, I've successfully upgraded my CE Rom to 1.40 WWE previously and it worked flawless with cooked 1.40 Ext Rom, however, the moment I upgraded my radio rom, my phone feature cannot be utilised. It just says No Service. I've seen on the forum Asian users using Qtec 1.08 radio rom.
Secondly, my understanding on the Oper and WWE is that by setting them correctly with XDA3tools, I can then upgrade them to my XDA without facing any country code errors or such. But would it affect my XDA functionality?
Lastly, can you make any recommendations on which is the most appropriate CE/Radio ROM version I should use for my XDA IIs based on WWE & O2ASI001?
THanks a millions! Believe me, I've really tried very hard to get my IIs to work and have throughly read through the guide, but to no avail...
I recommend that you just download a FULL, fresh, 1.40 Shipped EXE (I recommend the I-Mate one) and upgrade with it.
Use the first method described here to upgrade.
Dear TheLastOne,
I'll try that now! I'll post the results after that.
Thanks a millions!
I've successfully flashed my XDA IIs with I-Mate shipped exe. All went smoothly, but the same problem persist. No service. I guess I can pronounce my IIs official dead... Sob Sob
khngaroo
Could it be that your device is sim locked or that your sim card is no good?
Dear MDAIIIUser,
I believe that my SIM is not locked as I can make calls using the same SIM with another phone. When I insert my SIM card into my XDA, there wasn't any prompt or indication of my device being locked... Is there another way to verify that?
Thanks!
khngaroo said:
I've successfully flashed my XDA IIs with I-Mate shipped exe. All went smoothly, but the same problem persist. No service. I guess I can pronounce my IIs official dead... Sob Sob
Click to expand...
Click to collapse
Hi KHNGAROO... I am not an expers as TLO and MDAUser..but you can give a try downloading the 1.10 radio and downgrading your 1.40 istallation thet contains 1.12 radio to 1.10... I experienced a lot of problems on my device ( low signal or no signal) with the 1.40+1.12 radio combination..and I solved with hios trick..Dont know if can work for you..but maybe you can try..byez
khngaroo
The fact that you have no service would or could indercate that it is beining rejected by your network operator.
Alas, I have no Idea what message you get when a BA is locked to a sim.
(as in the provider has SIM locked your device so that you can only use it with that sim on his network).
The fact that you can use your sim in a different phone proves that the sim is not faulty however that does not verify if the Phone is sim locked.
Thus can you insert a sim from another device that you know that works into your BA and use it.
I have no idea what you had on the phone before you upgraded it nor if it worked, nor if you have also changed your sim so its just a bit hard to work out your probem.
At the moment it could be a locked device or a faulty instaltion of the radio rom.
You might have to go back to your Shipped version to verify if the device still works.
Then upgrade the OS only and check again
Then cook the Extromn to make sure you are not downgrading anything with the new 1.40 OS
Then upgrade the radio to a higher version 1.10 to verify if it works
The upgrade to 1.12 to prove or disprove vicer's very good suggestion.
Have fun
Be careful with the files that you use as you can't use Type I upgrade files to upgrade a Type II rom. Thus you will need to always download the files based on wiki and not reuse the old ones.
Dear MDAIIIUser,
I've flashed my original shipped asian rom back to my device. Got the SD bootable from my pal holding the same phone. Didn't work, still says No Service. I guess either my device is locked or the hardware is screwed.
Is there anything I can do to unlock my SIM on my XDA, should it be my XDA being locked. Or do I really have to bring it down to the service center to get the whole thing fixed?
Thanks a millions for all your help... Appreciated...
You still have not asnswerd the question of the sim. So I still dont know if it is the original sim or if you are using another on on a locked device.
So based on what I do know:
If you flashed the original Rom and have the correct sim and it does not work then your device needs to be sent back to the shop (which will be no problem as you have the original rom in it).
Wiki has a how to unlock (but like I said I dont know if that is your problem)
To all whom had helped me along the way (esp. MDAIIIUser & TheLastOne & vicer)
Brought my XDA IIs to Accord Dist and got it fixed. Now its back. I was told by the customer service operator that they had replaced the whole mainboard altogether. They didn't tell me what was the exact problem. Guess it was the hardware all along. But I was wondering, how on earth can flashing a ROM cause so much damage?
Therefore, here is a warning to those who wish to flash their XDAs, please do so only f you know what exactly you are doing. Please read wiki carefully before you try anything, or you might end up just like me, hee...
Well glad you solved your problem. There are a lot and I mean a lot of people that have been able to falsh thier device via this forum. But as you said you need to read and understand what you are doing.
So what rom do you have now and are you going to keep it?
(Not sure based on your sig)
Dear MDAIIIUser,
Weel, I've upgraded my CE rom to 1.40. However, I've decided to maintain my radio rom as it is (1.02), its kinda like once bitten twice shy. Quite sceptical that my IIs might end up in heaps again, lol.
Thanks again for all your help and concern.
khngaroo, I'm glad all your problems have been fixed. If it is indeed a hardware problem, then you should not hesitate to upgrade your rom.
(Besides, if the problem returns, you know they'll fix it )
TheLastOne said:
khngaroo, I'm glad all your problems have been fixed. If it is indeed a hardware problem, then you should not hesitate to upgrade your rom.
(Besides, if the problem returns, you know they'll fix it )
Click to expand...
Click to collapse
Dear TheLastOne,
I took your word for it and gave it another shot! Followed all the instructions found at WIKI and presto, it worked and now my IIs is running on 1.40 CE and 1.12 Radio.
Many, many, thanks to all of you who had helped along the way!
khngaroo
Great, Happy for you.
The 1.40 rom has a few issues that can be found on the wiki Upgrade page that you need to be aware of.
Hi to all that can help me, i just flash the rom yesterday night that i have download and its completed the upgrade and go into the screen and running the installing of the program that come with the rom.
after the full install and the device restart without any more power and picture show.
I have try to charge the battery with wall charger and also replace with new battery but still no power.
Is that mean i'm flashing with a wrong rom and what should i do now.
Can i get it fix?
nicholas99 said:
Hi to all that can help me, i just flash the rom yesterday night that i have download and its completed the upgrade and go into the screen and running the installing of the program that come with the rom.
after the full install and the device restart without any more power and picture show.
I have try to charge the battery with wall charger and also replace with new battery but still no power.
Is that mean i'm flashing with a wrong rom and what should i do now.
Can i get it fix?
Click to expand...
Click to collapse
That really sucks...
nicholas99 said:
Hi to all that can help me, i just flash the rom yesterday night that i have download and its completed the upgrade and go into the screen and running the installing of the program that come with the rom.
after the full install and the device restart without any more power and picture show.
I have try to charge the battery with wall charger and also replace with new battery but still no power.
Is that mean i'm flashing with a wrong rom and what should i do now.
Can i get it fix?
Click to expand...
Click to collapse
which rom did u flash it with ??? wat ver ur configs before that . ur ipl/spl version os and etc.
sometime it happens that the power button doesnt works ....
try poking the reset button wiz ur stylus ... press and hold for sumtime and c wat happens
if it starts then ... press it again and wen the screen goes blank pree the camera button and hold it ... ull get into the bootloader ... den connect da usb and flash a new rom or da old factry one ...
i use molski's rom its really stable
well i'm using Wizard_Love_2.26.10.2_WWE_Novii+CF2 for the first but after that i just try to flash the rom the the chinese support rom which is Dopod_CHT_TW_RUU by using the newromupdateutility to flash it to my phone. At the beginning the rom flash successful and login to the device for install all the program that come with. After all the installation done the device will restart but never boot up anymore even u can see any green light flashing at all. Please dont tell me i damage my rom, should i send for repair?
or someone can help me out please......
nicholas99 said:
well i'm using Wizard_Love_2.26.10.2_WWE_Novii+CF2 for the first but after that i just try to flash the rom the the chinese support rom which is Dopod_CHT_TW_RUU by using the newromupdateutility to flash it to my phone. At the beginning the rom flash successful and login to the device for install all the program that come with. After all the installation done the device will restart but never boot up anymore even u can see any green light flashing at all. Please dont tell me i damage my rom, should i send for repair?
or someone can help me out please......
Click to expand...
Click to collapse
did u try da soft reset ???
yes i did but nothing happen at all
Xda Neo
I have the same problem. IPL and SPL 2.15.00001 and tryed to downgrade but after restart it does not power on. Tried everything but no way to power on. Is somebody know how to make it work again.
Regards,
You guys tried to flash a G3 Rom on your G4 Wizard.
So your bootloader (IPL/SPL) that is 2.xx.0001 is overwritten by a G3 bootloader that is 2.xx, so in other words....your devices are bricked.
Please someone, correct me if I am wrong.
Molski
yup, I agree. Bricked hopefully someone can fine the JTag on these devices.
Wow that sucks! Full moon over Miami last night, naw that can't be it .....
Sorry but unfortunately I must follow my Grandmother's advice concerning when I don't have anything nice to say...
R there NO ALTERNATIVE WAY for THIS?? HOPE we can help those people that made a mistake by upgrading to a ROM that doesnt fit to their WIZARD. due maybe because of TOO XCITEMENT they forgot to CHECK FIRST(PLS! ALWAYS CHECK FIRST) their IPL/SPL.
HOPE those master GURU's can do something!
So, please someone tell clearly how to know G3 or G4 of the Wizard
thanks so much
Sorry but I have no more tolerance for people who just jump in first without doing a little research. A while back when the G4 first came out we didn't know. Now everyone who puts out a ROM warns people about the possible consequences. And there's so many threads on just the first page with tales of woe... how can a person miss them all??
I'm sorry but my parents raised me to take responsibility for my own actions, as Baretta used to say" Don't do the crime if you can't do the time"
Similar to when a Cat 4 hurricane is coming at you and you don't leave after being warned.... then blaiming everyone but yourself...
And if anyone wants to rebute me on this, don't bother as I've neither the time nor the patience.
Bottom line is that flashing phones has the very real possiblity of trashing an expensive piece of hardware in a very short period of time. If one has any doubts, then they shouldn't do it! And if a person doesn't have a concern initially then they're asking for trouble.
Sorry....
magicer said:
So, please someone tell clearly how to know G3 or G4 of the Wizard
thanks so much
Click to expand...
Click to collapse
a G4 has a .00001 on the initial splash screen.
ArtXT said:
R there NO ALTERNATIVE WAY for THIS?? HOPE we can help those people that made a mistake by upgrading to a ROM that doesnt fit to their WIZARD. due maybe because of TOO XCITEMENT they forgot to CHECK FIRST(PLS! ALWAYS CHECK FIRST) their IPL/SPL.
HOPE those master GURU's can do something!
Click to expand...
Click to collapse
The problem is that if your bootloader (IPL/SPL) is fuc*ed up, there is no way to get it in bootloader mode to do a flash!
Only known solution is with JTAG connector, but that solution is not a clear solution yet, but I dont know nothing about that solution (simply...because I never needed it).
Molski
Dr Puttingham said:
Sorry but I have no more tolerance for people who just jump in first without doing a little research. A while back when the G4 first came out we didn't know. Now everyone who puts out a ROM warns people about the possible consequences. And there's so many threads on just the first page with tales of woe... how can a person miss them all??
I'm sorry but my parents raised me to take responsibility for my own actions, as Baretta used to say" Don't do the crime if you can't do the time"
Similar to when a Cat 4 hurricane is coming at you and you don't leave after being warned.... then blaiming everyone but yourself...
And if anyone wants to rebute me on this, don't bother as I've neither the time nor the patience.
Bottom line is that flashing phones has the very real possiblity of trashing an expensive piece of hardware in a very short period of time. If one has any doubts, then they shouldn't do it! And if a person doesn't have a concern initially then they're asking for trouble.
Sorry....
Click to expand...
Click to collapse
I knew I have a G4 and can't upgrade/downgrade with G3 roms or even change IPL/SPL, but I did that :]
Just found ROM v2.22.1 (I think), like my original Wizard's was. I was so happy that I found it, that I forgot about G3 chips existence 8)
Well, ROM was for G3 -_-
Just ran too fast and slipped. Maybe I got that speed after very often Pioneer BCT 1430 flashing. It is just immortal :]
well i know about the G3 and G4 but the rom that i downloaded from doesn't say anything about support G3 or G4 thats why i consider this rom doesn't included IPL and SPL just like the custom rom been make from other member.
Damn now i have to send my phone back to factory for fixing it. Lucky i still have a warranty of it.
nicholas99 said:
well i know about the G3 and G4 but the rom that i downloaded from doesn't say anything about support G3 or G4 thats why i consider this rom doesn't included IPL and SPL just like the custom rom been make from other member.
Damn now i have to send my phone back to factory for fixing it. Lucky i still have a warranty of it.
Click to expand...
Click to collapse
I do feel for you. I believe that the best thing that we can do is to not even make G3 ROM's available to the general public. Maybe all new ROM releases should be IPL/SPL - less. If one needs a ROM that will upgrade their bootloader they'll have to request a password protected file.
I just dunno...
Dr Puttingham said:
I do feel for you. I believe that the best thing that we can do is to not even make G3 ROM's available to the general public. Maybe all new ROM releases should be IPL/SPL - less. If one needs a ROM that will upgrade their bootloader they'll have to request a password protected file.
I just dunno...
Click to expand...
Click to collapse
...which is one of the reasons why carriers make it so hard to flash a ROM from one carrier to the device of another.
Qtek 9100 half bricked
Hi Molski
I'm new here.Just 'd like to know if you could support me on this matter.
Here we go...
I've flashed my 9100 from wwe to esn (spanish) with the ROM 1.3.7.5 or something like this.
This is the problem...I got a power failure in the middle of the flashing process.So now the device isnt able to start up it didnt install the OS properly.
Now it says:
IPL 2.24 (i managed to flash the ipl n spl)
SPL 2.24
OS 1.3.7.5
But I'm pretty sure that there's no OS watsoever because after keep trying flashing with other ROM in bootload mode.I finally managed with an Orange of 34 mb it updated the ROM,that is the IPL And SPL and with the process was running I've noticed the screen got blank and updated it properly.I was realy happy when I saw it but even though it did it properly I still got the same problem.The pda doesnt start up.When I flashed it for the first time I did it with care,followed all the instructions,that is, unlocked the CID first etc.But had the damn joy of getting a power failure in the middle of it.
I'm just wondering if one of you would be able to gimme a light on it.I've tried everything but flashing it with a G4 ROM coz I know it wont work.
Regards
Luiz Santos
Molski[/QUOTE]
At the point I am I need the help of experienced Users from the community.
I flashed a original HTC Wings (S730) with WM 6.1 ROM. It runs perfectly until I got a hardware problem (radio) . This is the reason I have to send it back to the official service.
Therefore I tried to go back to an official ROM from the http://wiki.xda-developers.com/index.php?pagename=WINGS_WM61_Alcaline
At first I flashed the earlier backuped Bootloder via sspl-0.91-wings.exe. This seems to be okay. But as I tried to flash an official ROM from the site mentioned above, during the flashing process I've got the note 'ERROR 294 Invalid vendor ID'. What was wrong? Did I forget any step?
Please, is there anyone who can describe the correct way back to 'warranty' for a newbie?
Thanx a lot.
have you tried all the ROM's? there is one prerelease and two release ROM's.. try both of the release roms, they might be for different production models/locations.
I tried both official released ROM's (signed as 'Ship'), not the prerelease version.
and if you first flash the shiped rom (with hardspl) and when done flash the back-up of the spl
With reference to an earlier statement of bigflavour in the thread http://forum.xda-developers.com/showthread.php?t=383617&page=17
I flashed back the original SPL at first.
Too bad It seems to be that I have a new problem now. Few minutes ago I have tried to reinstall hardSPL on the device via the well known sspl-0.91-wings.exe running on the Wings. But as I started the sspl, the device shows on the display that 'Access denied....is not digitally signed with a trusted certificate'.
Thereupon I thought I had to 'application_unlock' the device. After running the SDA_App...Unlock on my PC the display message shows succesful unlocking process. B U T, the sspl doesn't run as before.
Now, I'm totally confused. What has happened??
It's flavor, and unfortunately, I have no idea how to help you.
Probably tried the European english's spelling hehe.
Also This does seem like an odd problem, have you tried for kicks doing the factory reset to see if it will reset some of the registry and maybe fix your issues? I dont know anything about the spl's since I have no need to upgrade to 6.1, I wouldnt imagine it causing any more damage but again I dont know what all was done. I havnt followed those threads for a long time.
Thanx a lot. Apparently, the hint to make a hard reset hits the mark. Now I flashed back the HardSPL. So I'm back at the starting line . Does anyone knows if the official ROM from the http://wiki.xda-developers.com/index..._WM61_Alcaline is the latest one and can I use it for the warranty return?
Or should I look for an original German HTC ROM?
I was a little bit to fast. I will need a German ROM definitely, because the ROM from the Wiki doesn't include a the german language option.
Is there anyone who can help me with a original HTC S730 ROM for the german market?
Thank you in advance.
Hallo HSN,
if you give me a introduction how I backup my ROM, you can have my one. I own a German HTC S730. But I am confused when I read all threads about flashing etc....
One page introduction how to back up and you can have my one.
But I think that the Repair center here in Germany, doesn't care about the Rom you have installed.
hi,
i got oner htc hd i hard spl it and the upgrade it to windows 6.5 all was working fine but it hangs a lot the i flashed it with windows 6.1 rom then the problem came was that all is working fine but i am unable to turn phone on to acess network on phone then i updated it ti the same rom i firstly used the problem was same then i update its radio then also problem was not solved then i update it other 6.5 rom but the problem is same phone doesnt turn on so that i cant acess network plz help me its very urgent for me
Are you sure the hspl update was successful? What spl version is currently showing on your device?
yes hspl was successful
manbir said:
yes hspl was successful
Click to expand...
Click to collapse
What spl is showing?
manbir said:
hi,
i got oner htc hd i hard spl it and the upgrade it to windows 6.5 all was working fine but it hangs a lot the i flashed it with windows 6.1 rom then the problem came was that all is working fine but i am unable to turn phone on to acess network on phone then i updated it ti the same rom i firstly used the problem was same then i update its radio then also problem was not solved then i update it other 6.5 rom but the problem is same phone doesnt turn on so that i cant acess network plz help me its very urgent for me
Click to expand...
Click to collapse
Perhaps you could give a bit more information about your issue. Interesting would be:
do you get the window to enter your pin?
and do you get any error message?
Matthes42 said:
Perhaps you could give a bit more information about your issue. Interesting would be:
do you get the window to enter your pin?
and do you get any error message?
Click to expand...
Click to collapse
i dont get any error and it is also not asking for any pin
its hspl is 1.56 olinex
Ok, so you have the right spl, so that is not the problem. To understand you, you say that you can not activate the phone? Does the phone stay in flight mode? If you go to Settings (Manila tab)\Wireless Controls and turn the Phone slider on, does it turn itself off again?
You can try to run the setup again. Go to Start\Settings (All Settings)\Connections\Connection Setup and make sure your Country and Operator are correct and press Ok to setup.
ClydeB1 said:
Ok, so you have the right spl, so that is not the problem. To understand you, you say that you can not activate the phone? Does the phone stay in flight mode? If you go to Settings (Manila tab)\Wireless Controls and turn the Phone slider on, does it turn itself off again?
You can try to run the setup again. Go to Start\Settings (All Settings)\Connections\Connection Setup and make sure your Country and Operator are correct and press Ok to setup.
Click to expand...
Click to collapse
am unable to turn the phone on rest all settings of country operator also ok
Is your device perhaps not SIM locked? What rom did you have originally? Have you tried to reflash to that original version and see if the problem is resolved.
When you first flashed to the 6.5 rom did the phone work then? I know you say you had lots of freezes, but before that did the phone work on the 6.5 rom?
sounds to me like a providerlocked phone
as he stated in his first post that he also flashed back 6.1
miniterror said:
sounds to me like a providerlocked phone
as he stated in his first post that he also flashed back 6.1
Click to expand...
Click to collapse
yes i flashed back to 6.1 but phone is not provide locked its phone is not turning on and i have cheked that all sims were working fine
miniterror said:
sounds to me like a providerlocked phone
as he stated in his first post that he also flashed back 6.1
Click to expand...
Click to collapse
manbir said:
yes i flashed back to 6.1 but phone is not provide locked its phone is not turning on and i have cheked that all sims were working fine
Click to expand...
Click to collapse
Thanks I saw that you did try a 6.1 rom, but I was asking if you tried the initial original 6.1 rom. You may have tried another 6.1 rom but not the original rom that was on the phone before you started flashing.
To my other questions then, did the phone initially work when you first flashed to the 6.5 rom? If after all of this and it was initially working on the 6.5 rom, you may have a hardware problem and may need to flash back to the original rom and take it back to HTC for a service.
ClydeB1 said:
Thanks I saw that you did try a 6.1 rom, but I was asking if you tried the initial original 6.1 rom. You may have tried another 6.1 rom but not the original rom that was on the phone before you started flashing.
To my other questions then, did the phone initially work when you first flashed to the 6.5 rom? If after all of this and it was initially working on the 6.5 rom, you may have a hardware problem and may need to flash back to the original rom and take it back to HTC for a service.
Click to expand...
Click to collapse
yes the phone was working fine when i firstly flashed to 6.5 rom and its not hardware how can i know which was original rom now at this condition???
manbir said:
yes the phone was working fine when i firstly flashed to 6.5 rom and its not hardware how can i know which was original rom now at this condition???
Click to expand...
Click to collapse
You can try going to the HTC website for your county and look to see if there is a rom upgrade available. If so you can enter your Serial Number to see if you can access it for download. Alternatively you can look for a stock rom here Try and find a friend near you with the HD and check their version.
Same problem here .....my wifi cant connect to anything..when im tryin to turn it on nothings happen and cant acces to web browsing..nothing works...i have flahed 4 roms till now and all the rom had the same problem...i ve flashed miris rom NRG rom Dutty rom and maryone....i dont know what to do....till before a week worked like a charm...but now it is still dead....
If your wi-fi was working and then on the same rom has suddenly stopped working that probably sounds like a hardware issue. You may need to flash back to rom and return the device for a service.
are you serious??cause in my country i leave in greece salonica..and the htc center is in athens and must send the device there and they told me to wait about one month or two to get it back....no way...!!!!but it is very strange...when i had miris rom it worked like a charm..after trying to flash a new rom to nrg then wifi stopped workin...tryed to flash another rom like duttys and maryone and still the same....why am i so unlucky???is there any solution???maybe is that any problem with rom?or misiing some file?
anyway thanks for reply....have a nice and a happy new year...god bless you!!
pm...sorry for my english...
edangel said:
are you serious??cause in my country i leave in greece salonica..and the htc center is in athens and must send the device there and they told me to wait about one month or two to get it back....no way...!!!!but it is very strange...when i had miris rom it worked like a charm..after trying to flash a new rom to nrg then wifi stopped workin...tryed to flash another rom like duttys and maryone and still the same....why am i so unlucky???is there any solution???maybe is that any problem with rom?or misiing some file?
anyway thanks for reply....have a nice and a happy new year...god bless you!!
pm...sorry for my english...
Click to expand...
Click to collapse
You can always try going back to the miri rom you were using, or to the original rom that was on the phone. If wi-fi still does not work then it sounds like it is a hardware issue and there is no other way around it that I can see but to take it in for a service, unless you think you can replace the part yourself. Is there no cell phone repair services in your location, although you may need to pay to have it repaired then as it will not be under HTC warranty then if you are prepared to take that chance. Sometimes these parts just break, it doesn't happen all the time, but hey even multi-million $ F1 cars break down.
ClydeB1 said:
You can always try going back to the miri rom you were using, or to the original rom that was on the phone. If wi-fi still does not work then it sounds like it is a hardware issue and there is no other way around it that I can see but to take it in for a service, unless you think you can replace the part yourself. Is there no cell phone repair services in your location, although you may need to pay to have it repaired then as it will not be under HTC warranty then if you are prepared to take that chance. Sometimes these parts just break, it doesn't happen all the time, but hey even multi-million $ F1 cars break down.
Click to expand...
Click to collapse
SO...FOR MANY HOURS TO FIND SOMETHING I MADE IT...THE SOLUTION IS UNDER START SETTINGS CONNECTION ADVANCED NETWORK AND THEN I JUST ENABLE FROM HSDPA/HSUPA TO ONLY HSDPA AND NOW ITS WORKING...
AS I THOUGHT THIS SETTINGS DEPENDS OF WHAT MODEM ROUTER YOU HAVE...JUST WORKING FINE NOW.....
SO EVEN MULTI MILLION F1 CAN BE FIXED UP......if you are rich and got the money...hahahaha
SO THANKS ANYWAY!!!!!!!!I AM GLAD FOR TRYING TO HELP ME.....
edangel said:
SO...FOR MANY HOURS TO FIND SOMETHING I MADE IT...THE SOLUTION IS UNDER START SETTINGS CONNECTION ADVANCED NETWORK AND THEN I JUST ENABLE FROM HSDPA/HSUPA TO ONLY HSDPA AND NOW ITS WORKING...
AS I THOUGHT THIS SETTINGS DEPENDS OF WHAT MODEM ROUTER YOU HAVE...JUST WORKING FINE NOW.....
SO EVEN MULTI MILLION F1 CAN BE FIXED UP......if you are rich and got the money...hahahaha
SO THANKS ANYWAY!!!!!!!!I AM GLAD FOR TRYING TO HELP ME.....
Click to expand...
Click to collapse
Hey, I'm glad you got it sorted. I'll remember to add that additional check to my little arsenal of things for troubleshooting. Thanks for the feedback.
So my problem is - I put android on my htc tytn II and it worked (well kinda) but anyway I decided to switch back to Windows Mobile...
I installed 1.27.x.x radio , found a Windows Mobile 6 ROM and put (Like in the instructions ) Kaisimg.nbh(renamed from ruu_signed.nbh) and Kaisdiag.nbh to my SD card and then started flashing... It flashed smth,rebooted automatically and started booting android again...
Then I hold again camera button + power+ reset and since then when I put EVERY .nbh file on my sd card and try to flash it it STUCK on "Loading.." If I try to flash it with USB It stays at 0%.
The only exeption is if I try to flash from USB the rom that I tried to flash before from my sd card.. then it starts 0%..1% and reboot the phone...
P.S: Please help me...I think my device is not Broken but I dont know what should I do to fix it...
To flash back to WM from android put your kaiser into bootloader (multi colored screen) Then connect to usb. Download any WM build that is recent (I suggest Phoenix 3 for this, you can flash whatever you want later). After you download it open and run the included RUU that came with it and it will flash it on there.
hmm, I also had experienced the similar problem on my 1st time flashing back to WinMo.
When you are trying to flash via USB cable and the process stopped at 1% I guess there is also a message about "Invalid vender ID" right?
and if the text in your bootloader (tricolor screen) doesn't mention anything about hard such as "3.29.0000" (not "3.29.hard")
then
you've lost your hard SPL that's why you cant flash any .nbh to your phone.
I had managed to solve this problem by flashing stock WM rom for kaiser. The rom also has to be suitable for your phone, I mean if your kaiser is originally from France, then use French kaiser stock rom. Or if you are using AT&T Tilt use kaiser cingular stock rom.
you can find the list of shipped roms for kaiser here :
http://shipped-roms.com/shipped/Kaiser/
If you still have the "invalid vender ID" error message, try another stock ROM.
Thanks man you're my hero! I though I lost my phone.. anyway i bought new one - Nokia 2730 Classic but Ill sell the kaiser...
Thanks Anyway ... you're god!
Have the same problem...
Firstly, I'd like to point that the reason for the hard SPL getting overwritten by an original SPL is NOT HAVING UPDATED HARDSPL to a newer version that prevents accidental overwrite. This is instructed in the previous steps before actually installing Android. That was my mistake (I had HardSPL 1.0 OliPof), and now I can't flash no rom to my Kaiser (which thankfully works quite well in Android).
What happens (please correct me if I'm wrong) is that "KAISDIAG.NBH" is a modified, standalone hardSPL that will flash to the phone the SPL that comes with the "KAISIMG.NBH" you put in your SD card with "KAISDIAG.NBH"). In my case, I used the WinMo 6.1 spanish version 3.29.412.0, which, resulted in my phone being flashed with the original SPL 3.29.
Now, it seems many users have fixed this locating the correct stock rom and flashing it in their Kaisers. But to others, like myself, nothing seems to work. I believe that this is because we not only need a stock rom for our specific Kaiser model, but also it has to be compatible with the SPL that accidentally got installed in the phone. The problem is what if such rom doesn't even exists?
I'm really thankfull for all I learned by reading the forums (and from my mistakes ) and I know I'm in no position to make requests, but here goes what I think could help the users like myself to fix this, if posible:
1) Guide to identify what model of Kaiser we have (maybe it's already there, I just couldn't find it)
2) Complete list (or lists) of stock roms (There are some around, those are easy to find I think, but it doesn't hurt to share different sources)
3) Something like a JumpSPL for Android would be more than awesome...
Thanks in advance to everybody, sorry for my own stupidity . Any idea or help would be much appreciated,
Daniel
hmm, I'm not sure if it has to be compatible with the SPL.
In my case, I was flashing a very old WWE stock rom which has original SPL 1.56.
I also had been very desperate because any stock rom I found seems doesn't work and I even didn't know where originally my kaiser came from because I get it from my uncle. So I tried to flash any WWE stock rom I could found but nothing works. I read from Wikipedia that based on my phone model (Kais100), this model was only sold as AT&T tilt for US. But the problem is my phone is HTC branded, not AT&T tilt. Well, based on this information I also tried to flash some cingular stock rom but the result was just the same.
After contacting HTC Customer care, I know more info about my phone. They told me that based on my phone product ID, my kaiser was originally shipped for US, but unfortunately they can't provide me stock rom for my phone model. So I searched myself but this time I had better objective : to search HTC branded rom but for US.
finally, after days of search. I've found the rom that is suitable for my phone. Its called HTC WWE Brightpoint US which has original SPL 3.29 at the bottom of the list on the website I told you on my previous post.
few weeks ago I also accidentally overwrite my HardSPL again, but this time I did it with the stock ROM which has original SPL 3.29. But this problem also solved by flashing the stock ROM I've found before via USB cable.
So, I guess it has nothing to do with spl version.
Keep tying don't give up.
Update: Step 1 completed! YAY
Using the serial number and some obscure google searching, I came to the conclusion my KAIS130 is australian. Cheers, mate!
I verified this by being able to download stock roms from the australian HTC site with my Kaiser serial number. But at the moment of writing this, have downloaded two roms and no luck yet. 5 minutes remaining for the third one... Wish me luck...
Daniel.
Well... Now what?
Tried all four rom-like thingies I could download on the HTC page, all of them returning error 294...
Now what? try to somehow extract the .nbhs from the exes and and use customRUU.exe? Try to flash from SD card?
Please help... Any ideas... I really want to get rid from that original SPL3.29.0000 It's evil!!! I think it won't never let me flash again.
Thanks,
Daniel
cuartetoraro said:
Tried all four rom-like thingies I could download on the HTC page, all of them returning error 294...
Now what? try to somehow extract the .nbhs from the exes and and use customRUU.exe? Try to flash from SD card?
Please help... Any ideas... I really want to get rid from that original SPL3.29.0000 It's evil!!! I think it won't never let me flash again.
Thanks,
Daniel
Click to expand...
Click to collapse
sorry to hear that..
well, extract the .nbh from exe and flash it via sd card is the method that made me overwrite my hard SPL in the first place.
hmm, did your phone comes with operator brand, such as three or something?
-Rif- said:
sorry to hear that..
hmm, did your phone comes with operator brand, such as three or something?
Click to expand...
Click to collapse
No, it's HTC unbranded. Now, something strange here: the label behind the battery has the serial number: HT830GB06075 and the P/N (guess it's part number) :99HCY194-00, but to the left of the camera, another label with the part number: 36H00563-00M and below says DATE:061107(TB02)/US.
I don't know if that's normal, but it caught my atention because my phone seems to have been dissasembled (little label over screw is teared). Maybe my Kaiser isn't Australian after all...