Database Develop

Shuts off when keyboard is slammed shut...

This is really bugging me but on occasion, when I slam the keyboard shut, the phone turns off. It also has happened when I opened the keyboard but only a few times.
I actually dissassembled the phone to see if maybe it was a loose connection somewhere. I did find that the keyboard ribbon cable was loosely connected so I reseated it firmly...but the problem didn't go away.
I also thought it may be either the SIMM card or the memory card contacts but after removing them, again, I still can reproduce the problem.
Understand that this is an intermittent problem and a little unpredictable but I can make it happen within a few tries. If I cautiously open and close the keyboard (without slamming it shut), I have no problems.
I don't believe it's software related because I can force it to happen when the device is booting up (with the Ericsson logo on the screen) before the OS loads.
Anyone else experiencing this?????
11/17/08 UPDATE: PROBLEM RESOLVED!
After further review and testing, it appears that the battery was losing connection to the battery contacts. I shoved a small crumb of paper folded up (about 1mm thick) at the back of the batt and the problem has gone away. Of course, I'm still holding my breath every time I open and close the keyboard but it looks like that may have been the problem. That's strange because I'm using the original battery. Thought this may help in case anyone else ever runs into this.

That sounds like a problem with the internals, maybe a you should get it replaced/repaired?

Kid says to doctor " IT hurts when I twist my arm backward like this." Doctor replies "then don't do that"
You say "my phone shuts off when I slam my keyboard shut" Doctor says "don't slam your keyboard shut"
this thought just made me laugh.
Seriously though. It does sound like an internal hardware issue that you should have fixed otherwise it may just get worse and start happening more regularly and at very inconvenient times.
Good luck.

Reminds me of my samsung slider phone the day that it died. I was sliding it back and forth.. sometimes the screen would go completely white and then come back.
By the end of the day, it went white and stayed that way.
Turns out the cable on the inside was slowly being cut from rubbing against the metal hole it was going thru every time the slider moved.
You've checked the cables before... but maybe its not cut yet, but something on the slider mechanism is hitting a wire/pulling on it.
Nobody knows.
But we all do know thats not normal. So yea get it replaced.

LOL!
hotrod101 said:
Kid says to doctor " IT hurts when I twist my arm backward like this." Doctor replies "then don't do that"
You say "my phone shuts off when I slam my keyboard shut" Doctor says "don't slam your keyboard shut"
this thought just made me laugh.
Seriously though. It does sound like an internal hardware issue that you should have fixed otherwise it may just get worse and start happening more regularly and at very inconvenient times.
Good luck.
Click to expand...
Click to collapse
That's funny!!!

I think you're right...
Nippero said:
Reminds me of my samsung slider phone the day that it died. I was sliding it back and forth.. sometimes the screen would go completely white and then come back.
By the end of the day, it went white and stayed that way.
Turns out the cable on the inside was slowly being cut from rubbing against the metal hole it was going thru every time the slider moved.
You've checked the cables before... but maybe its not cut yet, but something on the slider mechanism is hitting a wire/pulling on it.
Nobody knows.
But we all do know thats not normal. So yea get it replaced.
Click to expand...
Click to collapse
Yep...It's going back. Might as well get a fresh one. I know this problem existed for other phones before and the fix was mostly something simple that didn't require a replacement.

im getting exactly the same problem. gonna send mine back as well.

i have the exact same problem too! Waiting for a new one...
i thought i was the only one with this problem, but it looks like a production error as there are already 3 people on this board who have this defect.

technillion said:
This is really bugging me but on occasion, when I slam the keyboard shut, the phone turns off. It also has happened when I opened the keyboard but only a few times.
I actually dissassembled the phone to see if maybe it was a loose connection somewhere. I did find that the keyboard ribbon cable was loosely connected so I reseated it firmly...but the problem didn't go away.
I also thought it may be either the SIMM card or the memory card contacts but after removing them, again, I still can reproduce the problem.
Understand that this is an intermittent problem and a little unpredictable but I can make it happen within a few tries. If I cautiously open and close the keyboard (without slamming it shut), I have no problems.
I don't believe it's software related because I can force it to happen when the device is booting up (with the Ericsson logo on the screen) before the OS loads.
Anyone else experiencing this?????
11/17/08 UPDATE: PROBLEM RESOLVED!
After further review and testing, it appears that the battery was losing connection to the battery contacts. I shoved a small crumb of paper folded up (about 1mm thick) at the back of the batt and the problem has gone away. Of course, I'm still holding my breath every time I open and close the keyboard but it looks like that may have been the problem. That's strange because I'm using the original battery. Thought this may help in case anyone else ever runs into this.
Click to expand...
Click to collapse
yep, my problem seems to have gone now as well by using you're method. i was almost ready to send it back and then i saw you're post and tried your method and it worked !

Thats a pretty stupid mistake by SE...
They should do a quick fix by making new batters a smidge thicker. Of course they probably wouldn't offer free replacements, but they should fix it anyway.

technillion said:
11/17/08 UPDATE: PROBLEM RESOLVED!
After further review and testing, it appears that the battery was losing connection to the battery contacts. I shoved a small crumb of paper folded up (about 1mm thick) at the back of the batt and the problem has gone away. Of course, I'm still holding my breath every time I open and close the keyboard but it looks like that may have been the problem. That's strange because I'm using the original battery. Thought this may help in case anyone else ever runs into this.
Click to expand...
Click to collapse
Where did you place the paper exactly ? On the back of the battery where all the info text is or on the bottom ?
When my device is cold, eg in the morning for first use, this sometimes doesnt happen for >20x tries...but when i used it for a longer time and it almost always shuts down when slammed shut..but i already thought it might be something with the battery, but sometimes while slamming it shut for numerous times even the battery cover would come up and it didnt shut down...then in another situation it shuts down immediatly

Poor design...
toxical said:
Where did you place the paper exactly ? On the back of the battery where all the info text is or on the bottom ?
Click to expand...
Click to collapse
Yea...what I found with the design is that the ribbon cable connecting the keyboard sits right under the battery. In fact you can see the protrusion when you remove the battery under the white label. It moves when the keyboard is opened and closed. Slightly...but it does move.
...anyway...I folded a small piece of paper to wrap around the back edge of the battery.
Try this:
1. Make a small rectangular strip of paper about 10mm x 20mm and fold it the long way so you end up with a 5mm x 20mm piece.
2. Wrap it around the back/bottom edge of the battery as you reinsert it.
(If the battery fits more snug in its compartment, you got it right!)
3. Put the back cover back on--which should also be more snug.
4. Turn on the device and try it out (slam the keyboard).
(You don't have to wait for it to completely boot up...you can test it when the SE logo appears).
Be careful to use regular copy paper and not paper that's too thick as it may cause some other damage/problems with the device.

could you make a picture of that ?
Actually i will recieve a new device tomorrow, but i still have the feeling that this problem might reoccur as it seems to be a design flaw

technillion said:
11/17/08 UPDATE: PROBLEM RESOLVED!
After further review and testing, it appears that the battery was losing connection to the battery contacts. I shoved a small crumb of paper folded up (about 1mm thick) at the back of the batt and the problem has gone away. Of course, I'm still holding my breath every time I open and close the keyboard but it looks like that may have been the problem. That's strange because I'm using the original battery. Thought this may help in case anyone else ever runs into this.
Click to expand...
Click to collapse
I'm currently playing around with an old XV6800 I got off ebay, and this seems to have fixed the problem, so thanks

I had the same problem too.. but it was linked with the flex cable. Now i just don't use my keyboard even after fixing it.

Kaiser Powering off when in motion

Would it be an issue with the battery? or the board? rom?
It seems as if the battery looses connection with the phone or something along those lines, it works fine when I don't move it, but if i pick it up and go mobile, it turns off on random movements.
Is this a common problem? I have searched and didn't find any help.
TIA

No this isn't common, can you plug it in and move it around? Lets see what that does. I would think the phone is hozed.

ChumleyEX said:
No this isn't common, can you plug it in and move it around? Lets see what that does. I would think the phone is hozed.
Click to expand...
Click to collapse
Hozed? As in water damage? I don't remember it getting wet....
At first, when it started acting up, it didn't even want to charge or turn on. I would plug it in, turn it on and it would reset after the "HTC" screen, continuously.
Now I can plug it in no problem, and it charges. Sometimes, it'll tell me that the battery is out of juice after a few hours or charging, but its rare.
I'm also having trouble sync-ing
I sent the phone in to get it checked out and will post what the outcome is.
I really hope its the end of the batteries life, and not the phone

Hozed is an old techie term saying it's broken.

Stick a small bit of card between battery and back case see if that helps
As for the rest of your problems a hard-reset and if it's not just that the battery isn't making full contact a new battery...

Used to have that problem
This issue was mentioned here before.....and stylez suggested to you, I inserted a piece of folded paper between the battery and the phone (opposite to the battery terminals). Never had that problem again.....this was at least 10 months ago....

DesperateScorpion151 said:
This issue was mentioned here before.....and stylez suggested to you, I inserted a piece of folded paper between the battery and the phone (opposite to the battery terminals). Never had that problem again.....this was at least 10 months ago....
Click to expand...
Click to collapse
I had same problem and solved it by just adjusting the battery contacts. Pull them out a little.

Try rubbing the cold contacts of the battery and the phone with a pencil rubber.
It removes any oxydization, and slight corrosion off the contacts, also use the idea of the card to see if that helps!

Try rubbing the cold contacts of the battery and the phone with a pencil rubber.
It removes any oxydization, and slight corrosion off the contacts, also use the idea of the card to see if that helps!
Not sure why this has posted twice.
Please ignore.

Another probable cause
polish_express said:
Would it be an issue with the battery? or the board? rom?
It seems as if the battery looses connection with the phone or something along those lines, it works fine when I don't move it, but if i pick it up and go mobile, it turns off on random movements.
Is this a common problem? I have searched and didn't find any help.
TIA
Click to expand...
Click to collapse
Check that the SIM card door is fully closed and properly locked

punkhawaiian said:
I had same problem and solved it by just adjusting the battery contacts. Pull them out a little.
Click to expand...
Click to collapse
I've just used your tip to fix my T-Mobile G1. It was always powering off when it was in my pocket or when I flipped the screen out. T-Mobile said it was a software problem and I should return it - and survive with a crummy 2G loan phone for a couple of weeks while it was "with the engineers". ****ing idiots. So thanks a million!
This forum is, and has always been since I bought my Blue Angel in 2004, the most useful on the web! There are so many guys here who ROCK!

Sudden death and...root !

My phone decided to not switch on any longer. The only sign of life is the notification led blinking red when is in charge, no way to access it with any program if I attach it to the PC with a USB cable.
I should send it to the Sony repairing center (still under warranty) but the phone is rooted; given its situation do they discover it ?

I had that exact problem. Turned out that the battery suddenly died after about a year.
In my experience they never care what stuff is currently on the phone. Instead they'll just flash it with the latest stock rom after fixing the hardware.

Thanks a lot for sharing your experience. I really hope will be the same in my case as well. I'll post here what will happen.
PS I'm wondering about the batteries' quality: my daughter with a z1c had your same problem (a little more than one year life), you, may be myself... I know the sample is not significant but...

Same thing happened with mine & i was on a custom rom with unlocked bootloader...they probably had no way to get into the phone just like i couldn't so they probably couldn't tell it was modified...it was just a brick at that point...i noticed certain batches were affected by this sudden death and after pulling my tag out i noticed my phone was part of that batch that was poorly assembled in china...so brand new phone for me!

Fictional Reality said:
Same thing happened with mine & i was on a custom rom with unlocked bootloader...they probably had no way to get into the phone just like i couldn't so they probably couldn't tell it was modified...it was just a brick at that point...i noticed certain batches were affected by this sudden death and after pulling my tag out i noticed my phone was part of that batch that was poorly assembled in china...so brand new phone for me!
Click to expand...
Click to collapse
OK, another positive experience. I cross my fingers and I'll post what will happen to me

I have the impression they dont even check the software, they just flash a new fw and thats it. Or they dont care.

My phone locked up on me like this, but I solved it by pushing a pin into the reset button hole.

Geoff2 said:
My phone locked up on me like this, but I solved it by pushing a pin into the reset button hole.
Click to expand...
Click to collapse
Thanks for the suggestion but I tried any possible way to resurrect my phone, including what you're saying, without any result. I hope to confirm soon what all the contributors to this thread are saying...

Just received the device from assistance; everything went well: the motherboard was replaced.
The only drawback is that the lost the tiny grill that cover the mic at the bottom of the phone !!!!!

What is happening to my Nexus 6, is there aniway to fix it? [Water Damage]

My nexus 6 falled from my hand to a small puddle of rainwater like for 15-25 seconds, i picked off it then i saw that all works normally i dried it with my shirt and, saved it in to my pocket after a few minutes i wanted to do a phone call but saw that the screen were all black and showing some lines i went to my house and tried some times to turn it on but anything worked, then i left it in a container with rice for 24 hours today i tried to turn it on but it is not working , when i push the On button it just show some lines with a very light green/yellow background and the green notification Led is turned on. What i can do? what is happening to my nexus?i need to buy a new screen? is there another way to save my phone?
Any suggestion?
Hope someone could help me
i had taken some photos but i can't post it due to the restrictions of a minimum of 10 post in the forum but there is an album with two photos of the nexus in my profile.

It could be the screen. Mainboard is also a possibility here. Someone is going to have to look at it and see what's wrong.

Strephon Alkhalikoi said:
It could be the screen. Mainboard is also a possibility here. Someone is going to have to look at it and see what's wrong.
Click to expand...
Click to collapse
Thank you so much for answering, by the way i have posted some images of the phone in an album in my profile.

Rule of thumb with possible water damage is NOT to turn the phone on until it is dry. By turning on the Nexus, you guaranteed yourself a repair bill at best, or having to purchase a new phone at worst. Looking at the pics in your profile, your problem is on the motherboard. Someone will have to take the device apart and look at it to be sure, but you're likely looking at a motherboard replacement.
If you have a warranty, try using it.

Strephon Alkhalikoi said:
Rule of thumb with possible water damage is NOT to turn the phone on until it is dry. By turning on the Nexus, you guaranteed yourself a repair bill at best, or having to purchase a new phone at worst. Looking at the pics in your profile, your problem is on the motherboard. Someone will have to take the device apart and look at it to be sure, but you're likely looking at a motherboard replacement.
If you have a warranty, try using it.
Click to expand...
Click to collapse
[UPDATE] First i opened the nexus and disconected the battery from the phone dried competely with a towel then i left the phone for half an hour in a warm place then i dried it a little more with a heat gun , after that i left it in a bag of rice for two days and today i taked out the nexus, conected it to the charger then the green led started to turn on again, left it like for 4 minutes charging and then the nexus suddenly turned on! with all functioning correctly the screen the sim wifi all! , i was so happy and lifted up the smartphone to look at it but then the screen started to show some blurred lines and blue colors and a little bit distorsioned graphic interface in the screen but with all elements in screen.
Now i turned off the nexus
The problem could be the flexor of the screen?
because when i removed the back cover of the nexus with a guitar pick maybe i damaged the flexor or something like that
What i should do?

BryanMXB7 said:
What i should do?
Click to expand...
Click to collapse
As I've said repeatedly, get someone to look at it. With the symptoms you describe, there could be multiple causes, and only a technician or repair center can determine the actual cause.

Strephon Alkhalikoi said:
As I've said repeatedly, get someone to look at it. With the symptoms you describe, there could be multiple causes, and only a technician or repair center can determine the actual cause.
Click to expand...
Click to collapse
Thank you
Don't get angry
It was the flexor , All works nice but the flash does not work
I will try to repair it

I'm not angry, but I don't like having to repeat myself. Anyway, let us know if you get the flash fixed.

Xiaomi MI5 - Randomly unresponsive touchscreen

Hello guys, so I recently received an MI5 I ordered on Gearbest, in the 64gb international version (MIUI Global 8.2.2.0).
From day one, the touchscreen had the bad habit of going unresponsive randomly, meaning i have to struggle to swipe/click. Using hard keys (home, power) somehow fixes the issue for a few minutes but that's all. I unlocked the bootloader with Mi Unlock, and tried the latest build of LineageOS, and even flashed next the latest MIUI international developper build (29/06). On all of these 3 ROMs, the issue persists (and I went full wipe each time).
At the phone start, it is generally OK for a bunch of minutes, and then randomly becomes unresponsive.
I searched on the internet and did not find fixes, and i'm still unsure whether it's software or hardware related, even though I fear its the second option.
Would any of you have any more information on this subject?

To rule out any possible software issues, I'd flash the latest stable ROM.
Give that a shot and then see if the problem persists.

Well, the phone came new with the latest MIUI Global ROM (8.2.2.0), and since first start the problem was here. In the beginning I thought that it was just the phone lagging while setting up, but as time passed it was still there, no matter which ROM I flashed.
So, is there a potential software fix, or is this an hardware issue?

I am having the same issue, i hope its not hardware related :/

vlatko98 said:
I am having the same issue, i hope its not hardware related :/
Click to expand...
Click to collapse
Unfortunately, I'm starting to think it is, considering what I found on the internet. I'm kinda deceived by Xiaomi, which I thought was great value for the price. There is not even an official statement about this, even though many users reported the issue.

damien2702 said:
Unfortunately, I'm starting to think it is, considering what I found on the internet. I'm kinda deceived by Xiaomi, which I thought was great value for the price. There is not even an official statement about this, even though many users reported the issue.
Click to expand...
Click to collapse
Sadly thats the problem with Chinese phones,some of us that will face this problem's have no protection,we cant return the phone and get a new one,its better for us just to buy a new screen off aliexpress for 20euros than to wait 2 month's to ship it back and wait for it to be fixed and then returned and you pay the shipping costs and also the repair costs,but thats the risk we accept when we want the best bang for the buck.
Also poor quality control on the products to cut the costs is the real reason behind the problems we face

Had the same problem, it got fixed in the latest developer 7.6.29.

mundano said:
Had the same problem, it got fixed in the latest developer 7.6.29.
Click to expand...
Click to collapse
Hi, I indeed tried this solution, even thought it worked for a few hours.. But it came back soon enough

Guys,hello! I have a good news for you,i hope so. Ok. 1st of all I defeated the error with the screen off.
Here is my story.
I just wanted a black mi5. After some time found on ebay. I bought it, he arrived, after two days the touchscreen stopped working absolutely randomly.
The seller said that everything will do. I sent, he did nothing! Sent me. It all happened twice. Exactly twice I sent my mi5 from Russia to China! I read all the messages and tried everything. Nothing helped.
That's what I tried and that does not exactly work.
1. It does not depend on the version of miui or linegeOS.
2.This does not depend on time.
3.This does not depend on temperature.
I experimented, heated it, lay in the refrigerator. I clicked on the screen / body.
In the end, I understood the reason-static electricity.
HOW TO FIX IT!
1.Remove the back cover.
2. Twist the screws in the center and bottom, possibly a pair on the right side.
3. Try so far without the lid closed.
4.If the screen stops responding, try unscrewing the other screws.
5.Repeat, until you find the right combination and the touchscreen will work constantly.
Guys, I really helped it.
I hope this also solves your problem with the screen. Good luck!
I cant add a picture as a new user(((
Red squares-deleted screws on my configurations.
Green rounds-screws which i left without any changes.You can write me:[email protected]
or call me Skype: Griha3212
if you dont understand something in my instruction.

Griha3212 said:
Guys,hello! I have a good news for you,i hope so. Ok. 1st of all I defeated the error with the screen off.
Here is my story.
I just wanted a black mi5. After some time found on ebay. I bought it, he arrived, after two days the touchscreen stopped working absolutely randomly.
The seller said that everything will do. I sent, he did nothing! Sent me. It all happened twice. Exactly twice I sent my mi5 from Russia to China! I read all the messages and tried everything. Nothing helped.
That's what I tried and that does not exactly work.
1. It does not depend on the version of miui or linegeOS.
2.This does not depend on time.
3.This does not depend on temperature.
I experimented, heated it, lay in the refrigerator. I clicked on the screen / body.
In the end, I understood the reason-static electricity.
HOW TO FIX IT!
1.Remove the back cover.
2. Twist the screws in the center and bottom, possibly a pair on the right side.
3. Try so far without the lid closed.
4.If the screen stops responding, try unscrewing the other screws.
5.Repeat, until you find the right combination and the touchscreen will work constantly.
Guys, I really helped it.
I hope this also solves your problem with the screen. Good luck!
I cant add a picture as a new user(((
Red squares-deleted screws on my configurations.
Green rounds-screws which i left without any changes.You can write me:[email protected]
or call me Skype: Griha3212
if you dont understand something in my instruction.
Click to expand...
Click to collapse
please can you make video this help a lot

Hey guys, thanks to Griha3212 I found out on my Mi 5 it's the screw in the top middle part of the phone, the one with warranty sticker. Just loosen it a bit. It works fine after I loosen it. Tried tightening it too and the problem came back.

mi5 unresponsive
mundano said:
Had the same problem, it got fixed in the latest developer 7.6.29.
Click to expand...
Click to collapse
still fixed at these days? now after screen replacement and an update, the touch becomes unresponsive

Griha3212 said:
Guys,hello! I have a good news for you,i hope so. Ok. 1st of all I defeated the error with the screen off.
Here is my story.
I just wanted a black mi5. After some time found on ebay. I bought it, he arrived, after two days the touchscreen stopped working absolutely randomly.
The seller said that everything will do. I sent, he did nothing! Sent me. It all happened twice. Exactly twice I sent my mi5 from Russia to China! I read all the messages and tried everything. Nothing helped.
That's what I tried and that does not exactly work.
1. It does not depend on the version of miui or linegeOS.
2.This does not depend on time.
3.This does not depend on temperature.
I experimented, heated it, lay in the refrigerator. I clicked on the screen / body.
In the end, I understood the reason-static electricity.
HOW TO FIX IT!
1.Remove the back cover.
2. Twist the screws in the center and bottom, possibly a pair on the right side.
3. Try so far without the lid closed.
4.If the screen stops responding, try unscrewing the other screws.
5.Repeat, until you find the right combination and the touchscreen will work constantly.
Guys, I really helped it.
I hope this also solves your problem with the screen. Good luck!
I cant add a picture as a new user(((
Red squares-deleted screws on my configurations.
Green rounds-screws which i left without any changes.You can write me:[email protected]
or call me Skype: Griha3212
if you dont understand something in my instruction.
Click to expand...
Click to collapse
This is still working. Thx for help. Saved my phone after screen replacement.

Which Screws`?
I have the same Problem with my Mi5. Is there anyone who has a Picture for me, which Srews i have to loosen? Thanks

hotdogg1979 said:
I have the same Problem with my Mi5. Is there anyone who has a Picture for me, which Srews i have to loosen? Thanks
Click to expand...
Click to collapse
Hi Guys, I hope my solution helps to solve your problem. It is definitely about the screws. For me, I have found out that one screw is very slightly thinner than the others (of course the one with warranty stick should go to the centre and there is one silver metal going top left). This thinner screw should go up middle. That worked for me.

Does the screws trick work on your phone? Plz tell me.

Griha3212 said:
Guys,hello! I have a good news for you,i hope so. Ok. 1st of all I defeated the error with the screen off.
Here is my story.
I just wanted a black mi5. After some time found on ebay. I bought it, he arrived, after two days the touchscreen stopped working absolutely randomly.
The seller said that everything will do. I sent, he did nothing! Sent me. It all happened twice. Exactly twice I sent my mi5 from Russia to China! I read all the messages and tried everything. Nothing helped.
That's what I tried and that does not exactly work.
1. It does not depend on the version of miui or linegeOS.
2.This does not depend on time.
3.This does not depend on temperature.
I experimented, heated it, lay in the refrigerator. I clicked on the screen / body.
In the end, I understood the reason-static electricity.
HOW TO FIX IT!
1.Remove the back cover.
2. Twist the screws in the center and bottom, possibly a pair on the right side.
3. Try so far without the lid closed.
4.If the screen stops responding, try unscrewing the other screws.
5.Repeat, until you find the right combination and the touchscreen will work constantly.
Guys, I really helped it.
I hope this also solves your problem with the screen. Good luck!
I cant add a picture as a new user(((
Red squares-deleted screws on my configurations.
Green rounds-screws which i left without any changes.You can write me:[email protected]
or call me Skype: Griha3212
if you dont understand something in my instruction.
Click to expand...
Click to collapse
Thank you, you saved my Gemini :good:

Doesn't work for me. I tried with all screws.
Sent from my MI 5 using Tapatalk

screw solution works !!
I tried this solution with Redmi 2 and its the exact same screw which is the problem ie the screw right in the middle of the phone.
i loosed it slightly and now no more screen freezes. :good:

Hi I'm attaching an image with the screws numbered.
Griha3212 said:
Guys,hello! I have a good news for you,i hope so. Ok. 1st of all I defeated the error with the screen off.
Here is my story.
I just wanted a black mi5. After some time found on ebay. I bought it, he arrived, after two days the touchscreen stopped working absolutely randomly.
The seller said that everything will do. I sent, he did nothing! Sent me. It all happened twice. Exactly twice I sent my mi5 from Russia to China! I read all the messages and tried everything. Nothing helped.
That's what I tried and that does not exactly work.
1. It does not depend on the version of miui or linegeOS.
2.This does not depend on time.
3.This does not depend on temperature.
I experimented, heated it, lay in the refrigerator. I clicked on the screen / body.
In the end, I understood the reason-static electricity.
HOW TO FIX IT!
1.Remove the back cover.
2. Twist the screws in the center and bottom, possibly a pair on the right side.
3. Try so far without the lid closed.
4.If the screen stops responding, try unscrewing the other screws.
5.Repeat, until you find the right combination and the touchscreen will work constantly.
Guys, I really helped it.
I hope this also solves your problem with the screen. Good luck!
I cant add a picture as a new user(((
Red squares-deleted screws on my configurations.
Green rounds-screws which i left without any changes.You can write me:[email protected]
or call me Skype: Griha3212
if you dont understand something in my instruction.
Click to expand...
Click to collapse
It would be nice if you post which numbers have you tried.
Richardyii said:
Hey guys, thanks to Griha3212 I found out on my Mi 5 it's the screw in the top middle part of the phone, the one with warranty sticker. Just loosen it a bit. It works fine after I loosen it. Tried tightening it too and the problem came back.
Click to expand...
Click to collapse
Did you mean that, when loosen it, the problem dissapears immediately without rebooting? Because I've tried it and it does not work immediately.
Mamihla said:
Hi Guys, I hope my solution helps to solve your problem. It is definitely about the screws. For me, I have found out that one screw is very slightly thinner than the others (of course the one with warranty stick should go to the centre and there is one silver metal going top left). This thinner screw should go up middle. That worked for me.
Click to expand...
Click to collapse
I think your explaination is a little bit confusing. Did you mean that the thinner screw (the number 1 on the image attached) has to be swapped with the number 2? Or with the one with the warranty (number 5)?
Please if any other one found a combination that works, post it using the numbers of my attachment as reference. I have been tried several combinations amd no one seem to work.