Does it possible to reset the simlock counter try?
I've a problem with it : Simlock say i've tried 20 times to enter simlock code!
And now i can't valide new code : Ok button stay grey
This happened after i used vBar to kill Simlock task ! Number of try has reach 20 and now it seem to be lock for many days.
If someone can help me... Please cause now i've my simlock code but i can't valide if !
Ipaq Hw6515 French Bouygue telecom
Last ROM 1.23 French
vBar (great freeware but dangerous for simlock!) :
http://www.pocketpcfreewares.com/fr/index.php?soft=562
Go into bootloader using mtty.exe, you need to access AT command interpreter, in some htc devices this is done by command 'rtask 7' on others is 'rtask b' (I don't know on the beetles). Should be something like this:
Code:
USB> rtask b <--- go into AT command interface
ate1 <--- type this to enable local echo
atv1 <--- type this to enable verbose output
[email protected]=0,1,code <--- replace "code" with your MSL
[email protected]=0,2,code
[email protected]=0,4,code
[email protected]=0,8,code
[email protected]=0,16,code
[email protected]=0,32,code
[email protected]?40
If the last command returns simlock=00 means it's unlocked, other vaule means is still locked.
No need to reset the counter
[email protected] Doesn't work
Hi,
Thank for your reply but it doesn't work :
[email protected] doesn't seem to be implemented :
USB>h rtask
Usage:
rtask [Type [Value]]
Type(hex) 0: Reset radio and [value](hex) is ignore.
Type(hex) 1: Turn on radio, lease use type 3 and 4 instead.
Type(hex) 2: Turn off radio and [value](hex) is ignore.
Type(hex) 3: Run radio image and [value](hex) is ignore.
Type(hex) 4: Run radio bootloader and [value](hex) is ignore.
Type(hex) 7: Radio AT Command Debug.
Type(hex) 8: GSM trace route.
Type(hex) 9: Run radio external bootloader and [value](hex) is ignore.
Type(hex) A: Radio image flash by external bootloader and [value](hex) is ignore.
Type(hex) C: Select debug path.
Type(hex) D: Radio AT Command with GSM trace route.
Type(hex) 10: Set radio external boot UART mode(fast(1)/normal(0)).
USB>rtask 7
Radio AT command debug.
Wait 177 ms
ATCmd Version 0.1
CAIF Init Done
ate1
0
atv1
aatv1
OK
[email protected]?40
[email protected]?40
ERROR
[email protected]?40
[email protected]?40
ERROR
[email protected]?40
[email protected]?40
ERROR
ati
aati
Ericsson Mobile Platform
OK
And when i trie [email protected]=0, facility(0 to 32), unlocking code => ERROR
I've tried with the first ROM 1.05 and the last 1.23, with the 1.23 the help for rtask disappear!
Does Someone know another methode or command to accomplish my unlocking action? Please I gonna be crazy, I've left my ipaq running simlock 7 days and Validation button stay grey!! I've reset to test [email protected] without success
ouch, then hw6515 bootloader is different from what I've seen previously....
hw6515a locked
i have the same problems for months. my hw6515a 22 times. and i cannot have the button ok enabled. i cannot reset it. im still fresh on the boat. i downloaded the mtty.exe but i dont know how to use it. how to get my fone in the bootloader. Pof. you genius. plz show me how to unlock this fone. or reset the simlock count back. many thanks. Andrew. [email protected]
pof said:
Go into bootloader using mtty.exe, you need to access AT command interpreter, in some htc devices this is done by command 'rtask 7' on others is 'rtask b' (I don't know on the beetles). Should be something like this:
Code:
USB> rtask b <--- go into AT command interface
ate1 <--- type this to enable local echo
atv1 <--- type this to enable verbose output
[email protected]=0,1,code <--- replace "code" with your MSL
[email protected]=0,2,code
[email protected]=0,4,code
[email protected]=0,8,code
[email protected]=0,16,code
[email protected]=0,32,code
[email protected]?40
If the last command returns simlock=00 means it's unlocked, other vaule means is still locked.
No need to reset the counter
Click to expand...
Click to collapse
The bootloader are totally different, maybe the one that your are testing is on ipaq 6365...CMIIWW thanks
do HARD-RESET, that what i did to my H6515 USA version
Need a little help I am new with Ipaq 6515 but have unlocked other PDA and Pocket pcs, one thing how to put 6515 in bootmode and also how to hard reset it please can any one help.
thanks
bcnboy
need too to reset simlock counter.. this also can unlock beetles devices??
Hi all. I have the hw6515 spanish, sim locked, and french, without sim lock. Iz it possible to make both english and unlock it???
How to reset unlock codes counter on HP 6515a?
How can I manage connection with mtty.exe and device. Because there is not any COM ports emulated by AS.
Pof - a little help with X01HT
Hi - this worked on the HTC Hermes (I have X01HT)
Before i started - [email protected]?40 - returned - 01
I then ran [email protected]=0,1,code (code= the code I bought off a member here)
Then [email protected]?40 - returned - 00 (unlocked)
Thanks heaps
lemming77 said:
Hi - this worked on the HTC Hermes (I have X01HT)
Before i started - [email protected]?40 - returned - 01
I then ran [email protected]=0,1,code (code= the code I bought off a member here)
Then [email protected]?40 - returned - 00 (unlocked)
Thanks heaps
Click to expand...
Click to collapse
I think i need help with this. In mtty i get command error!!! all the time. Maybe I need to get the password? bootloader_pwn3d.pdf doesnt help.
I have my code, I just need to know how to input it. I have HardSPL installed maybe I will try flashing another rom to input the code?
How to apply to elf
dear sir
HOW TO APPLY TO ELF & what is Msl that will be inserted instead of code
Cant reset hermes
Khianto said:
The bootloader are totally different, maybe the one that your are testing is on ipaq 6365...CMIIWW thanks
Click to expand...
Click to collapse
DOES ANYONE KNOW HOW TO RESET COUNTS ON HERMES I TRIED LIKE THIS WITHOUT ANY RESULT
task 32
Level = 0
Cmd>28
Command error !!!
Cmd>task 32
Level = 0
Cmd>task 28
Storage format start
Write Nand Success
dwBlockToWrite = 13
Storage start block: 464
Storage Total block: 472
Total Bad Block in CE: 0
NeedToEraseBlockStart: 477
Storage format success
Cmd>task b
Cmd>task 7
Cmd>task b
Cmd>rtask b
Command error !!!
Cmd>rtask 7
Command error !!!
Cmd>task 7
Cmd>ate 1
Command error !!!
Cmd>ave 1
Command error !!!
Cmd>rask ave 1
Command error !!!
Cmd>task ave1
Cmd>task ate 1
Cmd>USB hrtask
Command error !!!
Cmd>hrtask
Command error !!!
Cmd>h rtask
Command error !!!
Cmd>task h rtask
Cmd>USB> rtask b
Command error !!!
Cmd>rtask b
Command error !!!
Cmd>rtask 7
Command error !!!
Cmd>'rtask b'
Command error !!!
Cmd>rtask 7'
Command error !!!
Cmd>[email protected]=0,1,code <--- replace "code" with your MSL
[email protected]=0,2,code
[email protected]=0,4,code
[email protected]=0,8,code
[email protected]=0,16,code
[email protected]=0,32,code
[email protected]?40
Cmd>
Cmd>[email protected]=0,1,00000000
Command error !!!
Cmd>simlock=00
Command error !!!
NO USB JUST CMD BUT I READ IT WAS THE SAME THING.
THANK YOU ANYONE WHO KNOWS OR HOW TO DOWNGRADE SPL 1.4 OLIPRO TO 1.04 I HAVE SIM LOCKED 18 TIMES THX. AND I HAVE THE CODE.
AND ANYONBE KNOWS HOW MANY TIME I HAVE TO WAIT FOR OK BOTTON? OR IT CANT BE DONE
Hi guys,
I'm having a problem with my G1, bought in UK. I tryed to SPL, and loaded a new Radio. In get the following when I go in fastboot:
HBoot-0.95.000
CPLD-4
Radio-2.22.19.26I
My problem is that the SD card is not recognized anymore, and when I put a card into the device I get a format message. This is what I get with ADG log cat:
I/vold ( 46): New MMC card 'SU01G' (serial 16941020) added @ /devices/platform/msm_sdcc.2/mmc_host/mmc1/mmc1:e624
E/vold ( 46): Unable to read device partition table (-1, I/O error)
I/vold ( 46): Disk (blkdev 179:0), 1984000 secs (968 MB) 0 partitions
I/vold ( 46): New blkdev 179.0 on media SU01G, media path /devices/platform/msm_sdcc.2/mmc_host/mmc1/mmc1:e624, Dpp 0
I/vold ( 46): Evaluating dev '/devices/platform/msm_sdcc.2/mmc_host/mmc1/mmc1:e624/block/mmcblk0' for mountable filesystems for '/sdcard'
D/MountListener( 73): handleEvent volume_checking:/sdcard
I//system/bin/fsck_msdos( 46): ** /dev/block//vold/179:0
W/AudioFlinger( 50): write blocked for 91 msecs
I//system/bin/fsck_msdos( 46): Invalid signature in boot block: 0000
I/logwrapper( 46): /system/bin/fsck_msdos terminated by exit(2)
D/vold ( 46): Filesystem check failed (not a FAT filesystem)
E/vold ( 46): vfat filesystem check failed on 179:0 (No data available)
D/MountListener( 73): handleEvent volume_nofs:/sdcard
D/Sensors ( 73): sensors=00000000, real=00000000
I tryed with several SD cards, Sandisk or Kingstone
Do you have any ideas about it?
I can't load any Rom and when I'm in bootmode I cannot use fastboot command, no skateboard Android at all!!!
Suggestions? Do you think it's an hardware issue? Have you evere experienced something like that? PLS!!
"D/vold ( 46): Filesystem check failed (not a FAT filesystem)"
Format the card in the computer, load the rom you want, then format the ext/swap if you wanted.
I did it already with no resolt at all! tryed in Fat/32 and ext2, the SD card is not recognized
This is the command I used to format the sd card:
format *: /FS:FAT32 /A:4096
I didn't try with an ext2 filesystem. Can you explain what you mean by "format the ext/swap if you wanted." ?
Thanks a lot for helping!
Format with ext/swap if you want to use those features. Did you format the card in the recovery or from the computer, try in recovery.
use a card reader to (maybe) rescue anything u want to keep from ur sd card then format ur card from ur computer. this happened to me before and this method worked for me, however the problem kept reccuring after a while si i got a new card.
Hi guys,
tnx for helping. Unfortunately I'm still unable to access the SD. I formatted the SD (more than one card) with another andorid phone, tried also to start in recovery, but no luck. I'm afraid is an hw problem, or may be a problem with the rom or radio I'm using at the moment. The phone it's not rooted yet, and with out SD I have no idea on how to solve this problem. Ideas? Is it possible to change the rom without using the SD?
can you mount the phone to a windows computer?
If so, just open my computer, right click on your phone and format it that way.
download all the needed files directly to the PC, move them to the formatted SD card, procede with rooting, installing your rom of choice and getting AmonRAs recovery image. Do a Nandroid+ext backup. Enjoy.
:edit: You said maybe a problem with the rom, but that it was not rooted yet... that doesnt make sense. Tell us EVERYTHING about what you have done if what I said above does not work.
Hi,
I'm in the process of preparing my sd card to try many of the available ROMs and noticed that common step is that a bootable sdcard partition is needed (either for clockwork recovery, or the actual bootable image)
I was thinking of partitioning my existing 4GB microsd card into 2 partitions 512MB,3.5GB and use the first partition for nook install purposes.
i.e the first partition/drive letter in windows will be the target of the image.
Will this work?
ps: created the two partitions using ubuntu's disk utility (virtualbox), the first one has the bootable flag..
Update:
Will attempt autonooter 3.0 like this!
dd command and output:
Code:
[email protected]:~$ sudo dd if=/mnt/share/auto-nooter-3.0.0.img of=/dev/sdb1
249344+0 records in
249344+0 records out
127664128 bytes (128 MB) copied, 32.303 s, 4.0 MB/s
[email protected]:~$ ls -l /dev/sdb1
brw-rw---- 1 root disk 8, 17 2011-03-02 17:58 /dev/sdb1
Update2:
It did not work. (autonooter didnt work/run)
I simply see two drives mounted (MyNOOKColor and AutoNooter2), NC reports a damaged sd card.
Update3:
All ok now, used one partition with autonooter
thanks
Whenever I run the command to turn my 64GB Sandisk microSD into a mixed storage (adb shell sm partition disk:179_64 mixed 93), it gives me "Error: java.lang.IllegalStateException: command '50 volume partition disk:179_64 mixed 93' failed with '400 50 Command failed'", even right after a format, both through Gparted, official SDFormatter and android using CM13 on 6.0.1.
Hi there,
My phone bricked and I'm posting to get help fixing it. (Sorry for my English)
Today my phone restarted and got into a boot loop (keep vibrating and showing logo and restarting). I had TWRP Recovery and B310 ROM (rooted) on the phone.
(I've flashed custom and official roms before but I've been on official android 4.4.2 B310 ROM for a couple of months)
>>These are what I did (Status: boot loop+logo+vibrating screen+working TWRP):
1. I went to TWRP and wiped cache but encountered an error indicating that the system could not mount /cache
2. Again I went to TWRP and tried to copy some of my internal memory data to my sd card but the same error (could not mount cache) occurred
3. I tried to unbrick the phone using flash tools, the process completed and I saw the green circle but nothing fixed and TWRP Recovery did not change too!
4. This time I opened flash tools and tried to flash B310 ROM (all the things except system and user data) hoping I could boot up the phone and backup internal memory data but that did not work.
5. Again I used flash tools to download B108 Signed ROM into the phone, the process encountered an error and I saw this time even the logo is not showing up and the phone only vibrates on the black screen and restarts. I tried to unbrick but this time this error occurred:
BROM ERROR: S_Security_Secure_USB_DL_Disabled (6041), MSP ERROE CODE 0x00
>>These are what I did (Status: Black vibrating screen+No recovery):
1. I formatted the phone using "AutoFormat" and "Validating" options successfully. I tried to Flash B108 Signed ROM and used Firmware>Upgrade but encountered this error: SP Flash Rool Error : (8045) No valid Partition Management Table (PMT) for storage device!
2. So I tried to reformat the phone and this time used "Download" to flash ROM 108 Signed, now this error shows up when the process reaches to 100% and the phone still is not working:
BROM ERROR: S_SECURITY_AC_REGION_NOT_FOUND_IN_SECROIMG (6128) , MSP ERROE CODE 0x00
What can I do now to fix this?
Is there any way to flash custom roms (zipped and flashable using custom recoveries) using flash tools?
Thanks for your help in advance.
Flash tools test output
Here is a memory test output from flash tools:
=============== Memory Detection Report ===============
Internal RAM: Size = 0x00020000 (128KB)
External RAM: Type = DRAM
Size = 0x41000000 (1040MB/8320Mb)
NAND Flash: ERROR: NAND Flash was not detected!
EMMC : EMMC_PART_BOOT1 Size = 0x0000000000400000(4MB)
EMMC_PART_BOOT2 Size = 0x0000000000400000(4MB)
EMMC_PART_RPMB Size = 0x0000000000400000(4MB)
EMMC_PART_GP1 Size = 0x0000000000000000(0MB)
EMMC_PART_GP2 Size = 0x0000000000000000(0MB)
EMMC_PART_GP3 Size = 0x0000000000000000(0MB)
EMMC_PART_GP4 Size = 0x0000000000000000(0MB)
EMMC_PART_USER Size = 0x00000001D2000000(7456MB)
============ NAND Test ============
SKIP! NAND Flash was not detected!
============ EMMC Test ============
EMMC Pattern Test(0x5A5A):
FAILED!!