please help! i used wmregoptimizer as i did before, after offing all the programs. After that, when i soft reset, it gave me an error. saying MICROP VERSION MISMATCH 0, PLEASE UPDATE LATEST MICROP FIRMWARE. i cannot backup anything. it is unable to read my memory card, as well as even connecting to the computer through a usb cable. anyone?...
Related
I tried using the Siemens upgrade for my SX66, which made it display Serial on the top and v2.07 on the bottom
I followed the steps reccomended for when such a thing takes place (ie doing a flash reset on the phone) but now the screen remains black and doesn't even display Serial and v2.07
When plugged into my computer, absolutely nothing happens and the computer does not recognize it.
I eventually got the screen to display USB, ran the update again but after about 15 minutes I got an error screen on the PC that read:
Error 201: Get Device Data Error
Can not get device data. Please make sure device are connected to PC and execute this update utility again
Please help!
Hi together,
I tried to flash my Charmer with a WM6 ROM. That failed, so I wanted to do a Hardreset --> Factory defaults. This failed because no OS was detected and it hangs up at bootscreen.
Going into Bootloader (3colors) and tried to connect via USB, the Bootloader shows me "USB" in the left corner, but if I start to flash an official ROM it says "ERROR 260 - Cannot connect to Device"...
Charmer seems to die... Several tries, no positive result...
While normal boot there are only shown 3 lines, but NO OS Version is shown up... Maybe no OS found???
What chances or possibilities do I have to get ANY OS on my PDA??
Heard something about flashing from SD??
How does it work, where can I find suitable Software/Manual for this? I do not have any ROM-Backup or something like that...
Help mee pleeeease...
I want to get my charmer reanimated...
Thx so far
bye
domi65
Please help me. I am desperate.
I have flashed my Telus HTC Touch Diamond with the "Telus_shipped french" ROM, following steps by steps the guide "Flashing a Rom or Radio from the 4 gig internal storage ".
My phone is stucked at the rainbow screen showing the following error message: "upgrade ROM code error. Please try again". No hard reset, no nothing will fix it.
Thx
connect it to ur pc when its in bootloder (the rainbow screen) where it says serial at the bottom it should now say usb, now just use a ruu to flash a new rom
Thank you so MUCH mancsoulja. I did not try it because after the flash my PC was not able to see my Diamond through the USB connection, so I thought that...
Just a question. How do I know if I should use the ROM for CDMA phone or the one for GSM?
When i try to Hard spl or flash a rom the 3 color appears than I get Error code 260 on bootloader schreen its says no connection detected, check usb or reconnect....
The 3 color screens turns grey and a message appeared and sayed loading...
bt nothing happend...
I have followed the basic steps how to spl and flas , switch to different usb connection port.
ever sinds i got my xperia back from se service repair my xperia is messed up help? how to solve this problem.
maybe this'll help
http://forum.xda-developers.com/search.php?f=470
hrabo said:
maybe this'll help
http://forum.xda-developers.com/search.php?f=470
Click to expand...
Click to collapse
Dude, he is right! That totally would solve the problem!
maybe try another sd card.
had the same prob but with another card it worked...
Error [260] : Connection
According the documentation I've read :
This error occurs when there is an “open port error” before upgrading the ROM image.
Solution: You can reset the device and run RUU again. If you still encounter an “OPEN PORT ERROR” again, reset your computer and try again, try another USB port, or try another computer.
About a year-ish ago windows stopped working on my spv3600 m700 Trinity. I looked into reflashing the phone & put a copy of schaps 4.30 striaght onto the fone no problems.
I now want to upgrade the rom again & can get it into the bootloader screen ok. My problem is that this is as far as I can get. I've even tried the minisd trick but I see loading box very briefly flash up on the screen & thats it...still in bootloader mode with serial but nothing else happens.
The fone is not bricked & if I reset it will load windows. I've tried the original flash & bootloader. Soft (SSPL) & hard Bootloader technique but to no avail.
Has anyone got any other solutions? Many thanks in advance, its sending me crazy!!
Ok I sorted the first problem of using SDcard to flash .MBH files. It was down to the miniSD card format not being FAT32. I reformat the card as FAT32 & then bootloader progressed to installation stage.
...now I have a new problem... i'm stuck in bootloader mode SPL 1.07.0000 IPL 0.50 after I used SSPL from my mobile in windows mode to get the 1.07ds override bootloader. This allowed me to flash the Radio to the latest chinese version. I then used this program again to Flash to windows 6.5 & then half way through it rebooted to the bootloader tricolour screen.
The problem is that now that windows is gone I can only run the standard bootloader SPL 1.07.0000 with the phone. If I try & upgrade a cooked ROM it comes up with an error code on the mobile. If I try an official version it checks the ROM & then says "not allowed".
Is there a way I can change the bootloader through the card SD? I can't either get the bootloader to change from serial msg to usb...doesnt matter how many times I plug in the USB & i'm using XP. Is there a way to force it into USB?
I've tried putting "Des crash proof SPL" ,"Hard SPL", "Hard SPL 1.20" onto SDmini card as TRINIMG.NBH bootloader loads then comes up with 00068002 error i presume on screen
I've tried putting official upgrades "RUU Trinity DOPODA SIA WWE...Ship.EXE rom" & "RUU Trinity HTC WWE .........GPS.exe rom" onto SDmini card as TRINIMG.NBH, bootloader loads, . . .checking, then displays "not allow" & "00028002" on screen! Now i'm really stuck!
Any help would be greatly appreciated!
looks pretty much the same like my trinity right now...
help would be very appreciated
Solved.
Finally worked out why my phone would not change from serial to usb on the bootloader screen. Its all down to the power from usb lead...luckily I have a double usb lead which I use for an external hard drive. Two usbs plugged into my laptop provides twice the current...as soon as I used this lead tadaaa, the phone comes on & is recognised by windows xp even when its in bootloader mode. If you don't have a lead try using a different computer...just incase the usb output is crap!
From here I then ran the unbrick / exploit program which you have to run two/three times but then this will put the phone into a bootloader which allows you to flash the phone with any ROM.
Hope this info is of any help.
steve54321 said:
Finally worked out why my phone would not change from serial to usb on the bootloader screen. Its all down to the power from usb lead...luckily I have a double usb lead which I use for an external hard drive. Two usbs plugged into my laptop provides twice the current...as soon as I used this lead tadaaa, the phone comes on & is recognised by windows xp even when its in bootloader mode. If you don't have a lead try using a different computer...just incase the usb output is crap!
From here I then ran the unbrick / exploit program which you have to run two/three times but then this will put the phone into a bootloader which allows you to flash the phone with any ROM.
Hope this info is of any help.
Click to expand...
Click to collapse
Still on bootloader with error 0068002
can't ran anything.
Please help......
SOLVED:::::::: sorry
Trinity bricked , pls help ...
steve54321 said:
Finally worked out why my phone would not change from serial to usb on the bootloader screen. Its all down to the power from usb lead...luckily I have a double usb lead which I use for an external hard drive. Two usbs plugged into my laptop provides twice the current...as soon as I used this lead tadaaa, the phone comes on & is recognised by windows xp even when its in bootloader mode. If you don't have a lead try using a different computer...just incase the usb output is crap!
From here I then ran the unbrick / exploit program which you have to run two/three times but then this will put the phone into a bootloader which allows you to flash the phone with any ROM.
Hope this info is of any help.
Click to expand...
Click to collapse
Hi , there ,
I am finding myself into the same situation but I do not realy get you : how You managed to get out of the bootloader mode where it says :
TRIN100
IPL-0.50
TRIN100
SPL-1.07.0000
Can you , pls, be more specific , cause I am a newbe who bricked his Trinity a week ago :::
Blocked with error 0068002
Hello, after I install nAr.23016.FRA.IE8-CHOME on my sfr s300+, I'm blocked on the first page HTC, etc...When I put the S300+ under bootloader (photo and power button action), I plug the USB and I itry to flash;result is a reboot. I try with TRINIMG.NBH and result is error 0068002.
I need help to resolve this problem.Can u help me? Regards.
dan (excuse my bad english)