Hi!
I can't turn on wifi. When I touch in switch it do not on. I already made several hard resets and this does not result.
How I can resolve this?
I have the same problem, anyone help us ?
1
must install slp-1.40.olinex
2
enter into bootloader
3
connect to usb (disable activesync usb)
3
open eprom.nb with an hex editor and replace 78 with your mac adress in revers mode :
for exaple
real mac is 00 - 18 - 41 - c0 - 68 - f1
be written f1 68 c0 41 18 00
at 50h - 60h
Code:
00 00 01 0D 56 40 00 00 - 00 02 6D 54 [COLOR="Red"]78 78 78 78 [/COLOR]| [email protected][COLOR="red"]xxxx[/COLOR]
[COLOR="Red"]78 78[/COLOR] 00 00 01 15 58 A4 - 00 00 00 01 31 56 01 02 | [COLOR="red"]xx[/COLOR]....X.....1V..
so will become
Code:
00 00 01 0D 56 40 00 00 - 00 02 6D 54 [COLOR="Red"]F1 68 C0 41 [/COLOR]| [email protected][COLOR="red"]ñhÀA[/COLOR]
[COLOR="Red"]18 00[/COLOR] 00 00 01 15 58 A4 - 00 00 00 01 31 56 01 02 | [COLOR="red"]..[/COLOR]....X.....1V..
4
copy eprom.nb into directory of mtty
5
open mtty
command :
task 32
lnb eprom.nb 880fc000 320
lnb eprom.nb 8839d9c0 320
reset
Tell me if solved
hi all
I have done exactly as laid out above but its doesn't seem to work. would it make any difference if the spl is signed or unsigned version?
Also does it matter what version of mtty you use?
any help you could shed on this would be great.
thanks in advance.
mrlard12 said:
hi all
I have done exactly as laid out above but its doesn't seem to work. would it make any difference if the spl is signed or unsigned version?
Also does it matter what version of mtty you use?
any help you could shed on this would be great.
thanks in advance.
Click to expand...
Click to collapse
i use unsigned version
i have the same problem, except that wifi can recive a small part of the signal..
I have a 300n router and i can see its signial only staying next to it...tne phone gives a low level data reception and has difficulties to get the ip....
i 'll change hard spl soon
LucaAL said:
i have the same problem, except that wifi can recive a small part of the signal..
I have a 300n router and i can see its signial only staying next to it...tne phone gives a low level data reception and has difficulties to get the ip....
i 'll change hard spl soon
Click to expand...
Click to collapse
but this solution is only wlan not turn on
not to turn on it is very similar to not to connect....by the way no changes after having installed the radio 1.17... i donnow if i have installed the hard spl 1.93 ..i did it but he is always 1.4...
LucaAL said:
not to turn on it is very similar to not to connect....by the way no changes after having installed the radio 1.17... i donnow if i have installed the hard spl 1.93 ..i did it but he is always 1.4...
Click to expand...
Click to collapse
ita :
allora da quello che ho capito
hai un router sitecom 300n
e il diamond non si connette anche se lo vede come segnale ?
eng :
then from what I understand
you have a router Sitecom 300N
and the diamond does not connect even though it sees as a signal?
I am sorry for my error....i have solved my problem disassembling the device and reassembling the cpu zone; there were a cple not enough plugged in his hole
Ita: inoltre ciao e scusate per il disturbo
gruptnt said:
1
must install slp-1.40.olinex
2
enter into bootloader
3
connect to usb (disable activesync usb)
3
open eprom.nb with an hex editor and replace 78 with your mac adress in revers mode :
for exaple
real mac is 00 - 18 - 41 - c0 - 68 - f1
be written f1 68 c0 41 18 00
at 50h - 60h
Code:
00 00 01 0D 56 40 00 00 - 00 02 6D 54 [COLOR="Red"]78 78 78 78 [/COLOR]| [email protected][COLOR="red"]xxxx[/COLOR]
[COLOR="Red"]78 78[/COLOR] 00 00 01 15 58 A4 - 00 00 00 01 31 56 01 02 | [COLOR="red"]xx[/COLOR]....X.....1V..
so will become
Code:
00 00 01 0D 56 40 00 00 - 00 02 6D 54 [COLOR="Red"]F1 68 C0 41 [/COLOR]| [email protected][COLOR="red"]ñhÀA[/COLOR]
[COLOR="Red"]18 00[/COLOR] 00 00 01 15 58 A4 - 00 00 00 01 31 56 01 02 | [COLOR="red"]..[/COLOR]....X.....1V..
4
copy eprom.nb into directory of mtty
5
open mtty
command :
task 32
lnb eprom.nb 880fc000 320
lnb eprom.nb 8839d9c0 320
reset
Tell me if solved
Click to expand...
Click to collapse
It don't work...
People, pls another solution?
I did as mention but honestly I don`t know where to find the MAC address of my device. In wireless, because it cannot be turned on, I cannot see the MAC address. Anyway, I try and change it like in your example, using the same MAC as you provided, but nothing happens. Any help appreciated!
A little while ago, I had problems with my phone not reading the SIM. When I tried to flash the stock firmware, the application crashed, resulting in a (hopefully) softbricked phone. I tried these methods trying to get it back to life:
http://forum.xda-developers.com/showthread.php?t=1843830 (post 4)
http://forum.xda-developers.com/showthread.php?t=2069723
And I also tried the LG R&D test tool to fash the kdz (I can't find the corresponding thread right now).
I've tried all of these methods on Win7 x64, Vista x64 and XP 32bit. The all did the same thing: they got stuck at wParam=2010 Iparam=210, so I think the phone is the problem and not the computers.
I was running CM11 with an unlocked bootloader. I can turn the phone on (and not off) but I can't get it out of the update mode. I can still update the phone until wParam=2010 Iparam=210, when it gets stuck. (I also tried waiting about an hour, nothing happened). As far as I know the phone is not a developer edition.
My question is, what do I try next?
Beunhof said:
I was running CM11 with an unlocked bootloader. I can turn the phone on (and not off) but I can't get it out of the update mode. I can still update the phone until wParam=2010 Iparam=210, when it gets stuck. (I also tried waiting about an hour, nothing happened). As far as I know the phone is not a developer edition.
Click to expand...
Click to collapse
Hello, and good day,
I have the same problem as you,
I also tried several guides ranging from installing KDZ files, through adb consoles and with a program (unfortunately I've forgotten the name) that caused the LG software to detect the KDZ files as an update for the phone, like it was from their servers, so it was 'intalled in an original way'.
But whatever, none of them worked.
Also, very important, mine gets also stuck on wParam=2010 Iparam=210,
I took the phone to a service store, where they repair cellphones through "boxes", but without success, they just mentioned that it would get stuck everytime at 15-25% of the installation process.
My Optimus 4X HD status is: can only access the S/W Update screen, or, if I turn the phone On it just shows and gets stuck on the LG logo.
It has no OS or recovery...
:crying:
Edit: I forgot to mention, I tried on Win 7 x64, x32 and on Win XP sp3 x32. So obviously the problem is on the phone.
Sounds like we have the same problem, except my phone doesn't show the boot logo at all, it instantly jumps to S/W mode when I turn it on.
After some searching, I found 3 methods I haven't tried yet:
http://forum.xda-developers.com/showthread.php?t=2475045
http://forum.xda-developers.com/showthread.php?t=2085344
http://forum.xda-developers.com/showthread.php?t=2797190
When I get back from work I'll give these a try, I will report back with results.
Does anyone have more suggestions or ideas? Should I contact LG for a fix?
Beunhof said:
After some searching, I found 3 methods I haven't tried yet:
http://forum.xda-developers.com/showthread.php?t=2475045
http://forum.xda-developers.com/showthread.php?t=2085344
[*]http://forum.xda-developers.com/showthread.php?t=2797190
Does anyone have more suggestions or ideas? Should I contact LG for a fix?
Click to expand...
Click to collapse
Hello again, I checked the three methods listed above,
i didn't like the first two really, but the third one got me so I'm doing it.
This is what I did and the result (on Win XP sp3 x32)
- Downloaded a fresh P880 V20A_00.kdz
- Downloaded and Installed fresh LGUnitedMobileDriver_S50MAN311AP22_ML_WHQL_Ver_3.11.3.exe
- During the drivers Installation, XP asked me to download and install this WMFDist11-WindowsXP-X86-ENU.exe (as suposedly I needed an mtp 11 runtime whatever). All good.
- Downloaded the LG Flash Tool 2014 from the guide, and moved the .kdz into that folder.
- Opened the program following the instructions on the post and started flashing my Optimus 4X with that Tool using CSE Flash.
- The second window named LG Mobile Support Tool that poped up started the process and had 4 modules
On the third module, the program started the Installation of the firmware on my device, on the S/W Update screen, after a while it reached 10%
Well.... it's been on 10% of the Installation progress for 43 minutes now (even while writing this response...).
The phone is perfectly recognized by the PC, I just dont get why it won't progress!....
Thanks tho, that LG Tool 2014 seemed really helpful. But still bricked.
Status:
After several investigation, I've also tried the following:
- Using P880_HK_V20B_00.kdz version, didn't work.
- Flashing thru kdz-update UpTestEX_mod2_marwin.exe, didn't work.
- Once LGMobile Support Tool is open, on the Tab "Additional Characteristics" I clicked on Recovery from Update Error.
The Tool asked for the Model & Serial Number of my device, which I entered and after the program tried to connect to the phone, said that it couldn't connect to the device.
I'm now totally sure that the problem is somewhere between the communication of the Computer and the P880, because:
Either KDZ-Update or LG Mobile Support Tool always gets stuck at what seems the 10% of the process.
Any method of flashing the device gets stuck and asks to remove battery and disconnect the usb, then replace and reconnect (an attempt to re-enable connection IMO)
Changing USB port on the PC always 'reinstall' the drivers, but with no avail.
Another thing I forgot to mention before, even tho every guide on XDA says that on the flashing process we should first "Install the drivers of the LG P880 from the list on the LG Mobile Support Tool", my tool (any version downloaded) never displayed LG P880 on the list, I've always had to use the UnitedDrivers package instead.
Any thoughts?
alessocf said:
Well.... it's been on 10% of the Installation progress for 43 minutes now (even while writing this response...).
Click to expand...
Click to collapse
I got to 10% in 52 seconds and then I got a disconnect error. I gave it a try with windows enabled just to make sure but the same thing happened. Seems like a nice and fast tool, too bad it couldn't do the trick.
This attempt also failed, but I might have some usefull information now:
Code:
[22:56:11.593]Selected 7 Binary : c:\users\beunhof\desktop\fix\lgp880at-00-v20b-eur-xxx-jul-17-2013+0.dz
[22:56:11.594]DoDownload : Retry(1)
[22:56:11.595]###### Port Opend(41) ######
[22:56:11.595]Opened COM41
[22:56:11.595]=====================================================
[22:56:11.596]= DLL Info : Dec 12 2012 11:01:58
[22:56:11.596]=====================================================
[22:56:11.602] MODEL:P880
[22:56:11.605] IMEI:000000000031
[22:56:11.611] PID:0000000003001721
[22:56:11.614] SWV:LGP880AT-00-V20b-EUR-XXX-JUL-17-2013+0
[22:56:11.617][VerReq]
[22:56:11.618]Model Name : Target(P880)
[22:56:11.618][FeatureQuery]
[22:56:11.633]This firmware supports the following features:
[22:56:11.633] - Protocol Version : 3
[22:56:11.633] - CP Download : TRUE
[22:56:11.633] - AP Download : TRUE
[22:56:11.633] - ROM Download : TRUE
[22:56:11.633] - MaxPacketLength : 0x40000
[22:56:11.633] - Battery Level : 37%
[22:56:11.633] - OperatingMode : 4
[22:56:11.633] - AutoUpdateBuffer : 1
[22:56:11.633] - ThreadOn : 1
[22:56:11.633] - Flashless : 0
[22:56:11.633] - UpdateBct : 0
[22:56:11.636] Dz Information
[22:56:11.636] - Model Name : Binary(P880)
[22:56:11.636] - SWV : LGP880AT-00-V20b-262-000-JUL-17-2013+0
[22:56:11.636] - BuildTime : 2013-07-18 01:35:51
[22:56:11.636] - SecureType : 1
[22:56:11.636] - TotalFiles : 10
[22:56:11.636] Loading FLS
[22:56:11.729]IntelFlash::GetDownloadSize
[22:56:11.729] - PSI : 35316
[22:56:11.729] - EBL : 157172
[22:56:11.729] - Hardware : 172
[22:56:11.729] - Security : 2048
[22:56:11.729] - DownloadData : 20572
[22:56:11.729] - Security : 2048
[22:56:11.729] - DownloadData : 167768
[22:56:11.729] - Security : 2048
[22:56:11.729] - DownloadData : 697892
[22:56:11.729] - Security : 2048
[22:56:11.729] - DownloadData : 356380
[22:56:11.729] - Security : 2048
[22:56:11.729] - DownloadData : 7864428
[22:56:11.729] Loading CFG
[22:56:11.733]NvidiaFlash::GetDownloadSize
[22:56:11.733] - BCT : 6128
[22:56:11.733] - EBT : 1132440
[22:56:11.733] - EKS : 684
[22:56:11.733] - SOS : 8228864
[22:56:11.733] - LNX : 7120896
[22:56:11.733] - APP : 925208920
[22:56:11.733]TotalSize : 83624509
[22:56:11.733]CP Download Starting : 0
[22:56:11.733]CP Binary has been loaded(9349476)
[22:56:11.733][Intel] MemoryMap
[22:56:11.733] FlashStartAddr : 0x40000000
[22:56:11.733] CUST : StartAddress(0x63000000), Length(0x00500000) : LINUX
[22:56:11.734] CUST : StartAddress(0x38000000), Length(0x08400000) : CLONE
[22:56:11.734] CUST : StartAddress(0x30000000), Length(0x08400100) : PREFLASH
[22:56:11.734] CUST : StartAddress(0x20000000), Length(0x00500000) : USBRO_ISO
[22:56:11.734] CUST : StartAddress(0x90000000), Length(0x001FE000) : CUSTDATA
[22:56:11.734][CMD_Intel_DownloadMode]
[22:56:12.294] - Device synchronized
[22:56:12.294][Injecting PSI RAM] : 35316
[22:56:12.294] - Sending PSI RAM
[22:56:15.354] - Receiving CRC
[22:56:15.367] - Received CRC OK : 01
[22:56:15.367] - Receiving ACK
[22:56:15.379] - Received ACK : 01 00 AA
[22:56:15.379] - PSI RAM Running
[22:56:15.379][Injecting EBL] : 157172
[22:56:15.379] - Sending EBL Length
[22:56:15.389] - Receiving ACK
[22:56:15.401] - Received ACK : 0xCCCC
[22:56:15.401] - Sending EBL : 157172
[22:56:29.112] - Sending CRC : FA
[22:56:29.121] - Receiving ACK
[22:56:29.169] - Received OK : 51 A5
[22:56:29.169] - Receiving Capabilities : 76
[22:56:29.184] - Boot-loader is active
[22:56:29.184] - EBL version: XMM6260_20.21_M1S1
[22:56:29.184] - Boot mode is: 00BB
[22:56:29.184] - EBL Running
[22:56:29.184][ReqSetProtConf]
[22:56:29.184] == prot_capabilities_t ==
[22:56:29.184] - protocol_version : 11
[22:56:29.184] - package_size : 2 -> 8
[22:56:29.184] - crc_type : 1
[22:56:29.184] - skip_writeblock_tx : 0
[22:56:29.184] - compression : 11 -> 10
[22:56:29.184] - compression : 10
[22:56:29.184] - flags : 1
[22:56:29.184] - erase_sector_verify : 0
[22:56:29.185] - flash_debug : 0
[22:56:29.185] - protocol_crc : 0
[22:56:29.185] - skip_erase : 1 -> 0
[22:56:29.185] - skip_wr_pack_crc : 0
[22:56:29.185] - Sending capabilities
[22:56:29.194] - Receiving ACK
[22:56:29.208] - Received : ACK 0100
[22:56:29.208][CnfBaudChange] : 3250000
[22:56:29.208] - Sending BaudRate
[22:56:29.217] - Receiving ACK
[22:56:29.254] - Received BaudRate : 3250000
[22:56:29.254] - Changing BaudRate
[22:56:29.267] - Changed BaudRate : 3250000
[22:56:29.267][ReqFlashId]
[22:56:29.267] - Platform : 14
[22:56:29.267] - ProjectName : XMM6260
[22:56:29.267] - Sending HardWare Info
[22:56:29.276] - Receiving ACK
[22:56:29.358] - Received ACK : 0000
[22:56:29.358][ReqCfiInfo_1]
[22:56:29.358] - Sending CfiInfo1
[22:56:29.368] - Receiving CfiInfo2
[22:56:29.406] - Received CfiInfo2 : 256
[22:56:29.406][ReqCfiInfo_2]
[22:56:29.406] - Sending CfiInfo2
[22:56:29.415] - Receiving ACK
[22:56:29.429] - Received ACK : FFFF
[22:56:29.429][Downloading BOOT CORE PSI(0)] : psi.fls
[22:56:29.429][ReqSecStart]
[22:56:29.429] - BootCoreVersion : 131072
[22:56:29.429] - Sending Security Start
[22:56:29.444] - Receiving ACK
[22:56:29.529][ERROR] Type : 0041 <> 0204
[22:56:29.529] - IndErrorMsg
[22:56:29.542]File_id(34), Line_number(415), Error_class(1), Error_code(79)
[22:56:29.542]File_id(16), Line_number(617), Error_class(1), Error_code(10)
[22:56:29.542]File_id(0), Line_number(0), Error_class(0), Error_code(0)
[22:56:29.542]File_id(0), Line_number(0), Error_class(0), Error_code(0)
[22:56:29.542]File_id(0), Line_number(0), Error_class(0), Error_code(0)
[22:56:29.542]File_id(0), Line_number(0), Error_class(0), Error_code(0)
[22:56:29.542]File_id(0), Line_number(0), Error_class(0), Error_code(0)
[22:56:29.542]File_id(0), Line_number(0), Error_class(0), Error_code(0)
[22:56:29.542] - Failure!
[22:56:29.542]ERROR : _Func_03_Ebl_0_ReqSecStart - Line(300)
[22:56:29.543]__Proc_NormalDownload : 0
[22:56:29.543]Error! IntelFlash:__Proc_NormalDownload
[22:56:29.544]_DoDownload : 0
[22:56:29.544]
-----------------------------------------Trace Last 100 Message-------------------------------------------------
[22:56:29.169][T000015] 43 01 00 00 4C 00 00 00 88 13 00 00 15 19 7E C...L..........
[22:56:29.184][R000086] 43 00 00 00 4C 00 00 00 BB 00 00 00 14 00 00 00 15 00 00 00 58 4D 4D 36 32 36 30 5F 32 30 2E 32 C...L...............XMM6260_20.2
[22:56:29.184] - Boot-loader is active
[22:56:29.184] - EBL version: XMM6260_20.21_M1S1
[22:56:29.184] - Boot mode is: 00BB
[22:56:29.184] - EBL Running
[22:56:29.184][ReqSetProtConf]
[22:56:29.184] == prot_capabilities_t ==
[22:56:29.184] - protocol_version : 11
[22:56:29.184] - package_size : 2 -> 8
[22:56:29.184] - crc_type : 1
[22:56:29.184] - skip_writeblock_tx : 0
[22:56:29.184] - compression : 11 -> 10
[22:56:29.184] - compression : 10
[22:56:29.184] - flags : 1
[22:56:29.184] - erase_sector_verify : 0
[22:56:29.185] - flash_debug : 0
[22:56:29.185] - protocol_crc : 0
[22:56:29.185] - skip_erase : 1 -> 0
[22:56:29.185] - skip_wr_pack_crc : 0
[22:56:29.185] - Sending capabilities
[22:56:29.185][T000101] 44 00 00 00 56 00 00 00 20 4E 00 00 CE 88 7E 02 00 86 00 4C 00 BB 00 00 00 14 00 00 00 15 00 00 D...V....N.........L............
[22:56:29.194][R000010] 44 00 00 00 56 00 00 00 D0 6E D...V....n
[22:56:29.194] - Receiving ACK
[22:56:29.196][T000015] 43 01 00 00 0C 00 00 00 88 13 00 00 E4 7C 7E C............|.
[22:56:29.208][R000022] 43 00 00 00 0C 00 00 00 02 00 86 00 02 00 01 00 89 00 03 00 B5 2C C....................,
[22:56:29.208] - Received : ACK 0100
[22:56:29.208][CnfBaudChange] : 3250000
[22:56:29.208] - Sending BaudRate
[22:56:29.208][T000029] 44 00 00 00 0E 00 00 00 20 4E 00 00 FB 9B 7E 02 00 82 00 04 00 50 97 31 00 9E 01 03 00 D........N...........P.1.....
[22:56:29.217][R000010] 44 00 00 00 0E 00 00 00 1E 5E D........^
[22:56:29.217] - Receiving ACK
[22:56:29.218][T000015] 43 01 00 00 06 00 00 00 10 27 00 00 EF B4 7E C........'.....
[22:56:29.230][R000016] 43 00 00 00 06 00 00 00 02 00 82 00 04 00 C7 FA C...............
[22:56:29.230][T000015] 43 01 00 00 04 00 00 00 88 13 00 00 58 51 7E C...........XQ.
[22:56:29.242][R000014] 43 00 00 00 04 00 00 00 50 97 31 00 9E D9 C.......P.1...
[22:56:29.242][T000015] 43 01 00 00 04 00 00 00 10 27 00 00 80 BF 7E C........'.....
[22:56:29.254][R000014] 43 00 00 00 04 00 00 00 9E 01 03 00 B7 96 C.............
[22:56:29.254] - Received BaudRate : 3250000
[22:56:29.254] - Changing BaudRate
[22:56:29.254][T000011] 45 00 00 00 50 97 31 00 F3 0E 7E E...P.1....
[22:56:29.267][R000010] 45 00 00 00 50 97 31 00 F3 0E E...P.1...
[22:56:29.267] - Changed BaudRate : 3250000
[22:56:29.267][ReqFlashId]
[22:56:29.267] - Platform : 14
[22:56:29.267] - ProjectName : XMM6260
[22:56:29.267] - Sending HardWare Info
[22:56:29.267][T000197] 44 00 00 00 B6 00 00 00 20 4E 00 00 2D 90 7E 02 00 01 08 AC 00 0E 00 00 00 00 00 00 02 00 C2 01 D........N..-...................
[22:56:29.276][R000010] 44 00 00 00 B6 00 00 00 5A DA D.......Z.
[22:56:29.276] - Receiving ACK
[22:56:29.277][T000015] 43 01 00 00 0C 00 00 00 88 13 00 00 E4 7C 7E C............|.
[22:56:29.358][R000022] 43 00 00 00 0C 00 00 00 02 00 01 08 02 00 00 00 0B 00 03 00 4F 25 C...................O%
[22:56:29.358] - Received ACK : 0000
[22:56:29.358][ReqCfiInfo_1]
[22:56:29.358] - Sending CfiInfo1
[22:56:29.359][T000027] 44 00 00 00 0C 00 00 00 20 4E 00 00 94 90 7E 02 00 84 00 02 00 00 00 86 00 03 00 D........N.................
[22:56:29.368][R000010] 44 00 00 00 0C 00 00 00 68 67 D.......hg
[22:56:29.368] - Receiving CfiInfo2
[22:56:29.369][T000015] 43 01 00 00 06 00 00 00 10 27 00 00 EF B4 7E C........'.....
[22:56:29.381][R000016] 43 00 00 00 06 00 00 00 02 00 84 00 00 01 B4 C7 C...............
[22:56:29.381][T000015] 43 01 00 00 00 01 00 00 88 13 00 00 53 D8 7E C...........S..
[22:56:29.394][R000266] 43 00 00 00 00 01 00 00 00 00 00 00 AD 00 B1 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 C...............................
[22:56:29.394][T000015] 43 01 00 00 04 00 00 00 10 27 00 00 80 BF 7E C........'.....
[22:56:29.406][R000014] 43 00 00 00 04 00 00 00 E3 01 03 00 7D 47 C...........}G
[22:56:29.406] - Received CfiInfo2 : 256
[22:56:29.406][ReqCfiInfo_2]
[22:56:29.406] - Sending CfiInfo2
[22:56:29.406][T000281] 44 00 00 00 0A 01 00 00 20 4E 00 00 F0 12 7E 02 00 85 00 00 01 00 00 00 00 AD 00 B1 00 00 00 00 D........N......................
[22:56:29.415][R000010] 44 00 00 00 0A 01 00 00 2E 76 D........v
[22:56:29.415] - Receiving ACK
[22:56:29.417][T000015] 43 01 00 00 0C 00 00 00 88 13 00 00 E4 7C 7E C............|.
[22:56:29.429][R000022] 43 00 00 00 0C 00 00 00 02 00 85 00 02 00 FF FF 85 02 03 00 0B 76 C....................v
[22:56:29.429] - Received ACK : FFFF
[22:56:29.429][Downloading BOOT CORE PSI(0)] : psi.fls
[22:56:29.429][ReqSecStart]
[22:56:29.429] - BootCoreVersion : 131072
[22:56:29.429] - Sending Security Start
[22:56:29.429][T002073] 44 00 00 00 0A 08 00 00 20 4E 00 00 C9 53 7E 02 00 04 02 00 08 00 00 00 00 00 00 00 00 00 00 00 D........N...S..................
[22:56:29.444][R000010] 44 00 00 00 0A 08 00 00 30 EA D.......0.
[22:56:29.444] - Receiving ACK
[22:56:29.445][T000015] 43 01 00 00 0C 00 00 00 88 13 00 00 E4 7C 7E C............|.
[22:56:29.529][R000022] 43 00 00 00 0C 00 00 00 02 00 41 00 40 00 22 00 9F 01 01 00 19 1D [email protected]".......
[22:56:29.529][ERROR] Type : 0041 <> 0204
[22:56:29.529] - IndErrorMsg
[22:56:29.529][T000015] 43 01 00 00 3E 00 00 00 88 13 00 00 03 9A 7E C...>..........
[22:56:29.542][R000072] 43 00 00 00 3E 00 00 00 4F 00 10 00 69 02 01 00 0A 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 C...>...O...i...................
[22:56:29.542]File_id(34), Line_number(415), Error_class(1), Error_code(79)
[22:56:29.542]File_id(16), Line_number(617), Error_class(1), Error_code(10)
[22:56:29.542]File_id(0), Line_number(0), Error_class(0), Error_code(0)
[22:56:29.542]File_id(0), Line_number(0), Error_class(0), Error_code(0)
[22:56:29.542]File_id(0), Line_number(0), Error_class(0), Error_code(0)
[22:56:29.542]File_id(0), Line_number(0), Error_class(0), Error_code(0)
[22:56:29.542]File_id(0), Line_number(0), Error_class(0), Error_code(0)
[22:56:29.542]File_id(0), Line_number(0), Error_class(0), Error_code(0)
[22:56:29.542] - Failure!
[22:56:29.542]ERROR : _Func_03_Ebl_0_ReqSecStart - Line(300)
[22:56:29.543]__Proc_NormalDownload : 0
[22:56:29.543]Error! IntelFlash:__Proc_NormalDownload
[22:56:29.544]_DoDownload : 0
[22:56:29.544]
-----------------------------------------Trace Last 100 Message-------------------------------------------------
[22:56:29.547]
------------------------------------------Trace Last 100 Message-------------------------------------------------
[22:56:29.547] ErrorCode(210)
Anyone an idea on what the strange hex-ish lines are? they show up just after the first error. Maybe something is encrypted? I'll google error code 10, 79 and 210 in a minute.
I lost hope and I can't bother to try the last link I posted, maybe tomorrow
Any thoughts on the log?
EDIT:
Searching the errors in the log led me here:
http://forum.xda-developers.com/showthread.php?t=2287267
http://forum.xda-developers.com/showthread.php?t=2786001
http://forum.xda-developers.com/showthread.php?t=2737915
The last one is identical to my problem, my phone also couldn't read my SIM. Sadly no one ever solved the problem here.
I think these solutions are the last resort:
http://forum.xda-developers.com/showthread.php?t=1448803
http://forum.xda-developers.com/showthread.php?t=1861942
I will give these a try later today when I get home.
Hello again,
I've checked the threads you mentioned above, as well as I've been googling to another forums. Yet no success.
Every thread where P880 gets stuck at param:207, Failure:207 or the infamous 10%; have no final solutions.
I've tried LGFlash Tool, LGFlash Tool 2014, LGSupport Tool, SmartFlash, KDZ-Update, each one w/o success and stopping at the same point.
The last and only solution I haven't yet manage to do, is using the program LGNPST v_2.2.3
I have it installed, it does recognize my P880 only on the "Emergency" tab, and automatically recognize it on COM19.
To make the flash procedure it requires a DLL and a BIN or CAB firmware, which I do not possess (I've only found .kdz and .dz firmwares)
Also, as far as I've read, the .kdz files when decrypted become .dz which when decrypted become .fls & .bin files.
That is my last hope... nobody seem to have an answer. Wish we had an ODIN for LG.
alessocf said:
To make the flash procedure it requires a DLL and a BIN or CAB firmware, which I do not possess (I've only found .kdz and .dz firmwares)
Also, as far as I've read, the .kdz files when decrypted become .dz which when decrypted become .fls & .bin files.
Click to expand...
Click to collapse
I used this method to create a .cab or .dz from a .kdz for this attempt.
Do you have a guide for the LGNPST? I can only find this thread.
A zeroed MEID could also be (part of) the problem:
If you encounter problems during flashing, upgrading or downgrading you may fall victim to your MEID/ESN being zeroed out.
The usual cause is pulling your battery while stuck on the white LG Software Update screen.
Click to expand...
Click to collapse
Thats exacly how I got bricked.
Beunhof said:
I used this method to create a .cab or .dz from a .kdz for this attempt.
Click to expand...
Click to collapse
Gonna try with that method for a.cab to use in the LGNPST, thanks.
Also, I'll try using the P880.dll that is inside the KDZ-Update folder.
Beunhof said:
Do you have a guide for the LGNPST? I can only find this thread.
Click to expand...
Click to collapse
Sorry, I can't remember where I got it, but I uploaded it to my dropbox for you, here is the link:
https://dl.dropboxusercontent.com/u/52565427/LGNPST v2.2.3.rar
It contains a Readme.txt with the instructions, its quite easy, the program looks like a suite.
Gonna report later the status. Good luck to both of us, lol.
EDIT: STATUS:
- Made a .cab file and used the P880.dll contained on the kdz-update folder for the LGNPST, the program instantly said "Finish!" and obviously, did nothing.
I'm probably doing something wrong there... but I've ran out of ideas.
Exact Same Problem!
Hi.
Looking all over the internet, the XDA forum in particular, to find a solution to my issue with my 4xHD.
It seems that I have the exact same problem as you describe; SIM not being recognised (out of the blue), eventually decided to re-flash to fix the issue (last resort after trying everything else I could find). Followed all instructions word for word; drivers installed, etc... etc... but when flashing stopped on 210... (not fully explaining, but essentially the same place it stopped for you). Waited hours, nothing happened, so forced to unplug phone. Therefore stuck on S/W mode after a failed/partial flash.
I have also attempted to complete this via every method I can find on here, but stops at the 210/10% point (depending on software being used), every time!
I love this phone and need it back up and running. If you have any luck sorting yours please update and let me know how the issue was resolved. Similarly, let me know if you have had no further luck and if I make any progress I will update you.
Cheers!
aaron_gavin said:
Hi.
Looking all over the internet, the XDA forum in particular, to find a solution to my issue with my 4xHD.
It seems that I have the exact same problem as you describe; SIM not being recognised (out of the blue), eventually decided to re-flash to fix the issue (last resort after trying everything else I could find). Followed all instructions word for word; drivers installed, etc... etc... but when flashing stopped on 210... (not fully explaining, but essentially the same place it stopped for you). Waited hours, nothing happened, so forced to unplug phone. Therefore stuck on S/W mode after a failed/partial flash.
I have also attempted to complete this via every method I can find on here, but stops at the 210/10% point (depending on software being used), every time!
I love this phone and need it back up and running. If you have any luck sorting yours please update and let me know how the issue was resolved. Similarly, let me know if you have had no further luck and if I make any progress I will update you.
Cheers!
Click to expand...
Click to collapse
Someone managed to solve. Already tried and everything.
Sup
Hello,
there is no software solution (at least known to me) for fixing this issue.
I've searched and scavenged all over the internet for a solution or at least AN EXPLANATION on why it does get stuck no matter what at 10% or Param:207.
My last resort (I'm trying it this weekend, will post later if it worked) is
a method called JTAG, where they kinda force-fix the boot software of the device connecting directly to the cellphone MoBo (for more explanation look on youtube)
Well, thats it... if it works, cheers, otherwise I'm throwing my Optimus 4X on a drawer.
Till' later.
alessocf said:
Hello,
there is no software solution (at least known to me) for fixing this issue.
I've searched and scavenged all over the internet for a solution or at least AN EXPLANATION on why it does get stuck no matter what at 10% or Param:207.
My last resort (I'm trying it this weekend, will post later if it worked) is
a method called JTAG, where they kinda force-fix the boot software of the device connecting directly to the cellphone MoBo (for more explanation look on youtube)
Well, thats it... if it works, cheers, otherwise I'm throwing my Optimus 4X on a drawer.
Till' later.
Click to expand...
Click to collapse
I will research this 'force-fix' and see if i can make any progress when i get some time off work. please update how you get on with this iff/when you try!
im feeling the same way with the phone; getting close to giving up, having tried all the software solutions word for word as described in the forums to fix it.
its strange that on all the guides when people have had similar problems as we are facing the response is usually to remove drivers+software and try again/follow the guide properly (not that im saying that a simple human error is not at fault the majority of the time). but i have not seen any posts were people have accepted that all methods have been attempted correctly and advice given regarding possible hardware faults and/or this 'force-fix' you mention.
if i am not able to fix myself i think i will consider posting a plea for someone more competent with this kind of stuff to have my phone posted to them in order to try and fix it for me. im sure that someone who is really into this kind of thing would like to have a go out of general interest, and the worst case scenario would be that i dont get my phone back (which is no use to me in its current state anyway).
cheers!
---------- Post added at 11:43 AM ---------- Previous post was at 11:22 AM ----------
aaron_gavin said:
I will research this 'force-fix' and see if i can make any progress when i get some time off work. please update how you get on with this iff/when you try!
im feeling the same way with the phone; getting close to giving up, having tried all the software solutions word for word as described in the forums to fix it.
its strange that on all the guides when people have had similar problems as we are facing the response is usually to remove drivers+software and try again/follow the guide properly (not that im saying that a simple human error is not at fault the majority of the time). but i have not seen any posts were people have accepted that all methods have been attempted correctly and advice given regarding possible hardware faults and/or this 'force-fix' you mention.
if i am not able to fix myself i think i will consider posting a plea for someone more competent with this kind of stuff to have my phone posted to them in order to try and fix it for me. im sure that someone who is really into this kind of thing would like to have a go out of general interest, and the worst case scenario would be that i dont get my phone back (which is no use to me in its current state anyway).
cheers!
Click to expand...
Click to collapse
UPDATE:
had a look at this JTAG repair method (also found a youtube video of some company touting for work, showing repair of a 4x hd - http://www.youtube.com/watch?v=5NRXhJxbtYY).
im not sure that i would want to go down that route, as they explain that it delves further into the phones software to fix issues caused by people bricking due to messing about to much after gaining root access. but i dont feel that this is the reason for the issues with my phone; had it set-up how i liked it for ages (without any real messing about after root), the issue with nonrecognition of my SIM came completely out of the blue (i attempted to re-flash to fix this; causing the stuck in s/w mode issue i now have, but the issue could quite easily be due to failing hardware as it could be an issue with the software).
in the case that it is damaged/failing hardware at fault JTAG would not be able to repair the phone, and even if it got my firmware back up and running there is no guarantee that it would recognise my SIM when i got it back.
so im not sure that i would be happy either paying someone to perform this 'fix' on my phone or paying for the hardware to attempt to fix myself, if its possible that the phone may still not work afterwards due to broken hardware. especially when you can buy a working model of our phone from places like ebay for under £100.
any thoughts or advice?
any luck/updates?
i think that i may just call it a day trying to fix this thing.
from what i have read it may be possible to fix the bootloader, thus allow to boot into recovery/fastboot/adb (hence not remaining stuck in an unflashable s/w update mode) in order to fix the phone, by using nvflash/apx mode. but it does not seem that our phones allow us access to do this.
have you had any luck with your mentioned jtag fix or otherwise?
had to get a new phone anyway (as was fed up using my old phone while trying to fix my 4x hd) - got a moto g 4g. am pretty chuffed with it for the price (enjoying screen mirroring through a miracast dongle and kitkat, etc...), but to be honest would go back to using my 4x hd if someone was able to find a fix.
any response/update would be appreciated, and if anyone thinks they can fix this issue please let me know.
cheers!
It's been a while!
Hey!
Long time since we had this issure with our 4X HD's, in fact almost a year since I had touched mine.
Was clearing out a drawer and found the brick. Which made me think, did anyone actually succeed in fixing their phone/solve this issue?
If so, I may have a bash just for the hell of it. If not, I think it's time for the bin.
:silly:
Whats Up
aaron_gavin said:
Hey!
Long time since we had this issure with our 4X HD's, in fact almost a year since I had touched mine.
Was clearing out a drawer and found the brick. Which made me think, did anyone actually succeed in fixing their phone/solve this issue?
If so, I may have a bash just for the hell of it. If not, I think it's time for the bin.
:silly:
Click to expand...
Click to collapse
Same here, didn't tried much since my last update. JTAG didn't work "cause Tegra based devices don't support it" or something like that.
Also tried with a homemade USB Jig Method, nothing happened.
My X4 is in my desktop, I use it mostly as a luxury paper holder.
Bless !.
alessocf said:
Same here, didn't tried much since my last update. JTAG didn't work "cause Tegra based devices don't support it" or something like that.
Also tried with a homemade USB Jig Method, nothing happened.
My X4 is in my desktop, I use it mostly as a luxury paper holder.
Bless !.
Click to expand...
Click to collapse
Guys, we may have a working solution: http://forum.xda-developers.com/optimus-4x-hd/general/maybe-nvflash-method-t3159853
I am currently testing it right now and until now it seems to work.
Update: It worked! My phone is booting again. Now i need to fix the IMEI and I am good.
Code:
C:\LG\\nvflash>nvflash --blob blob.bin --bct flash.bct.encrypt --setbct --configfile flash_encrypt.cfg --create --bl bootloader.bin.encrypt --go
Nvflash v1.7.75664 started
Using blob v1.1.57813ngs\Adm
rcm version 0X30001
System Information:
chip name: unknown
chip id: 0x30 major: 1 minor: 3
chip sku: 0x81
chip uid: 0x015d441469040a07
macrovision: disabled
hdcp: enabled
sbk burned: true
dk burned: true
boot device: emmc
operating mode: 4
device config strap: 0
device config fuse: 17
sdram config strap: 0
sending file: flash.bct.encrypt
- 6128/6128 bytes sent
flash.bct.encrypt sent successfully
downloading bootloader -- load address: 0x80108000 entry point: 0x80108000
sending file: bootloader.bin.encrypt
\ 1142880/1142880 bytes sent
bootloader.bin.encrypt sent successfully
waiting for bootloader to initialize
bootloader downloaded successfully
setting device: 2 3
creating partition: BCT
creating partition: PT
creating partition: EBT
creating partition: LGE
creating partition: EKS
creating partition: GP1
creating partition: SOS
creating partition: LNX
creating partition: APP
creating partition: CAC
creating partition: MSC
creating partition: USP
creating partition: NVA
creating partition: UDA
creating partition: DRM
creating partition: MLT
creating partition: FOT
creating partition: CAL
creating partition: UDB
creating partition: GPT
Formatting partition 2 BCT please wait.. done!
Formatting partition 3 PT please wait.. done!
Formatting partition 4 EBT please wait.. done!
Formatting partition 5 LGE please wait.. done!
Formatting partition 6 EKS please wait.. done!
Formatting partition 7 GP1 please wait.. done!
Formatting partition 8 SOS please wait.. done!
Formatting partition 9 LNX please wait.. done!
Formatting partition 10 APP please wait.. done!
Formatting partition 11 CAC please wait.. done!
Formatting partition 12 MSC please wait.. done!
Formatting partition 13 USP please wait.. done!
Formatting partition 14 NVA please wait.. done!
Formatting partition 15 UDA please wait.. done!
Formatting partition 16 DRM please wait.. done!
Formatting partition 17 MLT please wait.. done!
Formatting partition 18 FOT please wait.. done!
Formatting partition 19 CAL please wait.. done!
Formatting partition 20 UDB please wait.. done!
Formatting partition 21 GPT please wait.. done!
done!
sending file: bootloader.bin.encrypt
\ 1142880/1142880 bytes sent
bootloader.bin.encrypt sent successfully
sending file: eks.dat
- 684/684 bytes sent
eks.dat sent successfully
sending file: recovery.img
/ 7577600/7577600 bytes sent
recovery.img sent successfully
sending file: boot.img
/ 6496256/6496256 bytes sent
boot.img sent successfully
sending file: system.img
- 687920496/687920496 bytes sent
system.img sent successfully
GoodSoul said:
Guys, we may have a working solution: http://forum.xda-developers.com/optimus-4x-hd/general/maybe-nvflash-method-t3159853
I am currently testing it right now and until now it seems to work.
Update: It worked! My phone is booting again. Now i need to fix the IMEI and I am good.
[/code]
Click to expand...
Click to collapse
Greetings :fingers-crossed:, love to hear some good news and that it worked out for you.
I'm currently downloading the software and reading on how to use it, i'll be updating on how does it go for me.
Thank you for sharing this info with us.:highfive:
UPDATE: I T - W O R K E D !, after doing the process it automatically restarted and the LG Boot Logo reanimated, and started just as factory reset.
I had some issues installing the NvidiaUsb.inf, because I'm running on Windows 10 AMD x64 bits.
Steps I followed (in case someone needs them):
1) I had to open Command Prompt using the command: shutdown /r /o /f /t 00
THIS WILL RESTART YOUR COMPUTER
2)Then go through the options: Troubleshoot > Advanced Options > and look to "Disable Driver Signature Enforcement" using F7 key.
This allowed my W10 to Install the NVIDIA USB Boot-recovery driver for Mobile devices, which later allowed me to run NvFlash succesfully.
Current Status: LG P880 Boots and Runs!, doesn't have Baseband Version or IMEI, but this is something easier to fix.
Mostly appreciated.
UPDATE: I T - W O R K E D !, after doing the process it automatically restarted and the LG Boot Logo reanimated, and started just as factory reset.
Click to expand...
Click to collapse
Yippie!
Current Status: LG P880 Boots and Runs!, doesn't have Baseband Version or IMEI, but this is something easier to fix.
Click to expand...
Click to collapse
If you know how please let me know. I tried for serveral hours to fix that problem but had no luck yet.
Mostly appreciated.
Click to expand...
Click to collapse
You are welcome.