Related
Please help, I was uninstalling some applications from my HTC PURE and had to restart the phone, when it was rebooting it hung at the ATT screen and there was small red text in the bottom left screen.
I had previously installed HardSPL 1.83 but relocked it via instructions in 2nd post because I'm still deciding if I wanna keep the phone and didn't wanna do anything for warrenty reasons.
I have the stock ROM and never installed anything except the HardSPL and the revert.
Please help me, I have tried to load the ATT Pure Stock/Shipped ROM I found here but everytime I try to in the bootloader mode it says either "no image file" or hangs at loading depending what I've tried to name the file. Also I've tried to run customruu.exe to install the stock ROM and also tried to install HardSPL 1.83 but it hangs at 0% and eventually wants to do recovery on the PC.
How do I fix this problem, and preferabbly get it back stock. I do have a warrenty, well unless I violated it by installing HardSPL then doing the revert.
Thanks
viper2g1 said:
Please help, I was uninstalling some applications from my HTC PURE and had to restart the phone, when it was rebooting it hung at the ATT screen and there was small red text in the bottom left screen.
I had previously installed HardSPL 1.83 but relocked it via instructions in 2nd post because I'm still deciding if I wanna keep the phone and didn't wanna do anything for warrenty reasons.
I have the stock ROM and never installed anything except the HardSPL and the revert.
Please help me, I have tried to load the ATT Pure Stock/Shipped ROM I found here but everytime I try to in the bootloader mode it says either "no image file" or hangs at loading depending what I've tried to name the file. Also I've tried to run customruu.exe to install the stock ROM and also tried to install HardSPL 1.83 but it hangs at 0% and eventually wants to do recovery on the PC.
How do I fix this problem, and preferabbly get it back stock. I do have a warrenty, well unless I violated it by installing HardSPL then doing the revert.
Thanks
Click to expand...
Click to collapse
Of course you hard reset?
Make sure your SD card is formatted to Fat32 and you may mant to try a different card, 2gb - 4gb.
What does your SPL say now in bootloader mode?
Yes I tried a hard reset. I can try another sd card the one I used was fat32 and 2gb. I believe it says 1.33 can't look now but I know it's not the same as an untouched pure.
Help!
You are not the only one who is having this issue. I am frustrated beyond frustrated. How are other people flashing their out of the box ATT Pures using the same exact steps but I can't? It's making no sense.
1. I turn off firewalls.
2. I've tried both usb and sd card boot, didnt work
3. I installed the enablerapi cab
Nothing works and I am having the same problem you are having...it stays on 0% forever and it doesnt even prompt me saying there is an error it just sits on 0% until I unplug it...
Help!
themasterhook2000 said:
You are not the only one who is having this issue. I am frustrated beyond frustrated. How are other people flashing their out of the box ATT Pures using the same exact steps but I can't? It's making no sense.
1. I turn off firewalls.
2. I've tried both usb and sd card boot, didnt work
3. I installed the enablerapi cab
Nothing works and I am having the same problem you are having...it stays on 0% forever and it doesnt even prompt me saying there is an error it just sits on 0% until I unplug it...
Help!
Click to expand...
Click to collapse
Are you trying to HSPL or flash a ROM?
Well
According to what i've read, you have to do Hard SPL before you flash a rom, so i've been trying to HardSPL and it doesn't work! I even tried to skip the step and just flash the rom and it doesnt work..
Now, I also have an ATT Tilt to and I JUST flashed a rom 30 mins ago, so it has nothing to do with firewalls or anything as far as my computer goes, I think its the phone, so what can I do?
How to flash HSPL.
themasterhook2000 said:
According to what i've read, you have to do Hard SPL before you flash a rom, so i've been trying to HardSPL and it doesn't work! I even tried to skip the step and just flash the rom and it doesnt work..
Now, I also have an ATT Tilt to and I JUST flashed a rom 30 mins ago, so it has nothing to do with firewalls or anything as far as my computer goes, I think its the phone, so what can I do?
Click to expand...
Click to collapse
Its a good thing flashing the ROM didn't work, you'd be bricked.
For flashing HSPL, it seems that newer phones are having an issue.
Something may have been changed that is preventing the unlocker from working.
Do the following;
1. Hard Reset
Instructions:
- Soft reset with stylus
- Hold Vol up & Vol dwn simultaneously until white screen appears
- Following screen prompts, Press Vol up to confirm.
2. Go to bootloader mode.
Instructions:
- Turn off your device using the power button
- When the device is turned off, simultaneously press the Vol dwn + Power button
- Your device will startup in Bootloader mode
Should say SPL: 1.33 or something.
3. Sync your phone to your PC.
4. Install enablerapinew.cab
5. Unzip both Topaz_CustomRUU_v1.1.zip & SPL_183.zip to the same folder
6. Run the CustomRUU.exe
This process should install HSPL and now when you enter bootloader mode you should see something like SPL: 1.83 Olinex.
If so, you're ready to start flashing custom ROMs.
If not, please report all errors to the HSPL thread or PM Olipro.
**I take no responsibility for any loss of data or functionality of your device.**
See, the problem with your instructions are...
1. You cannot soft reset with the stylus, I don't see a button anywhere on the phone ( ATT PURE not Diamond 2 )
2. Holding Vol up & Vol down simultaneously until white screen appears doesn't work. The only thing that works is when I hold Vol Down and the screen with the colors come up, not a white screen.
So i'm still lost. Thanks for your help regardless. I just really want to flash a new rom so I can stop using this stupid slow ATT rom.
So basically you are messing with your Pure and don't know how to soft reset?
Remove the stylus and in the groove for the stylus is a red dot, that is the red reset button. Insert the tip of the stylus in the red dot and push. Now the Pure will soft reset.
Probably should familiarize yourself with the device before you finish turning it into a brick!
Oh wow. That is so hidden.
On my Touch Pro 2 its right there on the side where you can see it, with words.
Anyway, Thank you very much, i'll try that.
Still, what about the Up and Down button volume button function so I can go into bootloader mode?
themasterhook2000 said:
On my Touch Pro 2 its right there on the side where you can see it, with words.
Anyway, Thank you very much, i'll try that.
Still, what about the Up and Down button volume button function so I can go into bootloader mode?
Click to expand...
Click to collapse
Now that you found the soft reset button.... follow my procedures.
Note- you have to hold the keys IMMEDIATELY after soft reset before the boot screen appears.
Ok.
Bruce Inman said:
Now that you found the soft reset button.... follow my procedures.
Note- you have to hold the keys IMMEDIATELY after soft reset before the boot screen appears.
Click to expand...
Click to collapse
Didn't work, I re-did the steps you listed 3 times over to make sure I was correct and the same results. I guess ATT has found a way to stop their phones from being unlocked.
Thank you for your help regardless.
themasterhook2000 said:
Didn't work, I re-did the steps you listed 3 times over to make sure I was correct and the same results. I guess ATT has found a way to stop their phones from being unlocked.
Thank you for your help regardless.
Click to expand...
Click to collapse
You should probably post over in the HSPL thread.
You'll get more help over there. There are many others having similar issues and there may be a fix over there.
FYI, when you get to the tri colored screen, that is where it shows what SPL you have currently.
Updating rom freeze
Hi, I don't post much if at all, normally you guys have it right on the button, this is my 3rd phone to run custom roms on but for some reason it just freezes on the "Updating ROM image on your PDA Phone..." screen and doesn't continue past, on my last 2 phones active sync worked well with updating to custom roms,seems like my Pure produces the same error after the attempt, its a communication error "ERROR [262] : UPDATE ERROR", now recovering from the error is not a issue, we all have familiarity in that area but I was wondering if it could be something as simple as the cable that was sent with my phone or if its possible to flash rom through sd card as opposed to using active sync?
drearystate said:
Hi, I don't post much if at all, normally you guys have it right on the button, this is my 3rd phone to run custom roms on but for some reason it just freezes on the "Updating ROM image on your PDA Phone..." screen and doesn't continue past, on my last 2 phones active sync worked well with updating to custom roms,seems like my Pure produces the same error after the attempt, its a communication error "ERROR [262] : UPDATE ERROR", now recovering from the error is not a issue, we all have familiarity in that area but I was wondering if it could be something as simple as the cable that was sent with my phone or if its possible to flash rom through sd card as opposed to using active sync?
Click to expand...
Click to collapse
Yes, you can flash through storage card, just rename the .nbh to TOPAIMG.nbh, Put in root of storage card and enter bootloader mode.
You have HSPL'd, right?
Bruce Inman said:
Yes, you can flash through storage card, just rename the .nbh to TOPAIMG.nbh, Put in root of storage card and enter bootloader mode.
You have HSPL'd, right?
Click to expand...
Click to collapse
I was just going through the thread. I have the same issue. i have place topaimg.nbh in the root of storage card and entered bootloade mode, it shows loading and is stuck at 0%.
HSPL is 1.83. Went through entire thread of HSPL but unfortunately didn't find any solution.
arun.ramachandra said:
I was just going through the thread. I have the same issue. i have place topaimg.nbh in the root of storage card and entered bootloade mode, it shows loading and is stuck at 0%.
HSPL is 1.83. Went through entire thread of HSPL but unfortunately didn't find any solution.
Click to expand...
Click to collapse
Just to confirm, you have to name it exactly "TOPAIMG.nbh".
With all of the people that have tried all methods and still can't flash, something must have changed in the stock SPL.
Hello people
Hello, did anybody found the way to flash HTC PURE , I have the same problem 0%
Thanks
same problems here
i have same problem with pure to.
coldun187 said:
Hello, did anybody found the way to flash HTC PURE , I have the same problem 0%
Thanks
Click to expand...
Click to collapse
From HTC site (HTC Pure support):
What is a Soft Reset and how is it performed?
A soft reset basically resets the memory structure in the handheld. This recovers the device from memory conflicts, corrupted system service chains (mainly due to attempting hacks), memory leaks, and system lockups due to the “Fatal Exception” program errors. Removing the battery from the device while it is still powered on is NOT a soft reset and can actually damage the device.
A Soft Reset is performed by:
Remove the Battery cover and the Stylus from the device.
Insert the tip of the stylus into the Reset hole located at the entry point of the stylus silo.
The device will reboot.
New to G1 and have a problem. Bought a G1 and it came with elcaires rom I think it was.
So I downloaded UK RC7, renamed it to Update, and placed it on the root of my card.
Held the home and power button, and tried to install but I'm getting installation aborted each time. I've also tried to wipe, but that gets aborted too.
I rebooted and now its stuck on G1 screen
I hope somebody can help, had the phone an hour and I've mucked it up already.
Thanks in advance
Im also "bricked" at the loading screen, i turn it on and it gets frozen at the tmobile screen. Home+power, camera+power, Alt+L etc dont work.
Is this fixable?
sirlewis said:
Im also "bricked" at the loading screen, i turn it on and it gets frozen at the tmobile screen. Home+power, camera+power, Alt+L etc dont work.
Is this fixable?
Click to expand...
Click to collapse
No. It's Not.
if its not than what should he and i do?
Are you trying to boot into recovery while its in the G1 screen?
yo my name is sammy as well and i swear i just did the same thing with my g1 on eclair. hit me up dude on [email protected]. we can try and help each other out. plus i love the uk man. i never been, but plan too very soon. i love the music and the accents of the women, oh god. hit me up bro!
If you cannot access recovery or bootloader, you have a rather expensive paperweight. If you can, then you have hope.
AroundTheWorld said:
If you cannot access recovery or bootloader, you have a rather expensive paperweight. If you can, then you have hope.
Click to expand...
Click to collapse
It is not so expensive since it be can brought for less than 100>$$
You can fix it by replacing the board with one from a working phone which is not the easiest thing to do.
hey ill take one of those paper weights... I need a new screen...
in the same boat cant get into anything hung up on splash screen
maybe our only option is jtag, ive never bricked before i always put cm 4 then go and install cm5 above that and it worked but this time it told me to go kick rocks and and and it was a customers phone so i gave him mine which is running eclair.
you guys arn't bricked. If you can turn on the phone than your perfectly fine.
You just gotta learn how to use it
G1 hanged at white screen!
Hi all,
I really need a help here. I have a G1 rooted with CM rom ver5. it was working fine since 3 months but suddenly now the phone doesnt boots up, it goes to white screen with 3 droid skaters and highlight on Hboot. It is freezed then and nothing can be done. I removed battery and tried booting by home + power ; camera+power etc etc . nothing happens it goes to that screen only. i have amons recovery and also nand backups in sd card. but the system doesnt let me go any where!! Please help......
attached is the snapshot
Either your back-button hangs, or something messed up your phone completely.
But as long as you have the fastboot mode, it's not bricked. I would suggest you to clean everything, i.e.
Code:
fastboot erase system -w
fastboot erase boot
fastboot erase recovery
and then flash recovery again, i.e.
Code:
fastboot flash recovery <recover.img>
After that you can boot into recovery and restore your latest backup.
Please note: fastboot is a command you execute on your PC and you have to connect your phone with USB to your PC.
If after that procedure your phone boots again into hboot, most likely your back-button is defect.
I myself I think got a bricked G1...
I first installed many custom roms and thought that they were slowing my g1 so I wanted to get my g1 back to normal... For that I googled and was gone to the htc official website and ported the radio and rom from there but unfortunately I read it somewhere and it said that the rom is for only developers phone.
Everything first went very good... no error on clockwork recovery but when I reboot my phone, it got stuck on T-mobile G1 logo screen? I now can not even go to recovery mode or in fastboot mode? I need help...
Someone told me to use odin multi loader? but how do I use it or do it?? I need some instructions?
What should I do now? All I want to do right now is to get rid of my g1 by fixing it and selling it at once!!!
before flashing radio, spl, rom...anything...u need to check out the warnings and compatibility-MUST!!!!
there are 32B and 32A devices...both have different stuffs for themselves....which can be bricked if u dont follow the guidelines and try to act in sort of a haste to accomplish something new!!!
for those who can get to the camera+power (hboot) screen, but cant do anything else...u need to format ur sdcard...FAT32...then download dreaimg.nbh file...keep it in the root of ur sdcard...
then boot into the hboot menu, and ur phone should read the dreaimg.nbh file and prompt u to take an action(flash it)....do that and it'll get ur phone to the stock rom thingy....
then later u gotta root ur device again(telnet, great)....then install amon ra's recovery...change radio and what not and play again....
u gotta be patient...that's the only thing!!!
check this too
http://code.google.com/p/android-roms/wiki/Get_Root
Earlier this evening I decided to try to get Android working on my Tilt. Through several series of failure to get everything working properly I decided, screw it, I'll go back to WinMo for now.
However, Custom_RUU doesn't work when Windows doesn't recognize a phone...
Oh well. No big deal. I'll flash from my microSD.
Except that I can't get my phone to go to the bootloader.
When I try (holding the camera button) it just stay on the splash-screen indefinitely.
Otherwise, it proceeds to enter Android as per the usual.
This is very frustrating as it renders my phone useless until this is resolved.
Any help is appreciated. Thank you.
60 views and nobody has any ideas?
Pleeeeeeaaase???
Bootloader is press and hold camera and power buttons while doing a soft reset.
I have tried that. I have tried every combination of buttons whilst reseting possible and it either hangs on the bootsplash or proceeds to boot a non-working Android.
Time to recheck everything's by the book for microSD flashing
vindiconotitia said:
it either hangs on the bootsplash or proceeds to boot a non-working Android.
Click to expand...
Click to collapse
So if it's proceding to boot a non-working andriod installation on occasion, then the bootloader is still working (at least some of the time). On those occasions, if you've set up the microSD flash card correctly, it should grab the files off of there and procede to flash itself. You'll need to recheck that everything is correctly setup for microSD flashing. What does the 'splashscreen' as you call it read?
Bootloader for kaiser is camera + power or camera + soft reset holes. The camera button sometime have to be press accurately to get bootloader. It happen to me as well when I bricked my kaiser flashing a full cooked ROM without flashing stock first.
Flying Kiwi said:
So if it's proceding to boot a non-working andriod installation on occasion, then the bootloader is still working (at least some of the time). On those occasions, if you've set up the microSD flash card correctly, it should grab the files off of there and procede to flash itself. You'll need to recheck that everything is correctly setup for microSD flashing. What does the 'splashscreen' as you call it read?
Click to expand...
Click to collapse
It shows the custom splash screen. No radio info or anything like it used to. It shows the splash screen and then boots. It used to show radio info and version, etc.
vindiconotitia said:
It shows the custom splash screen. No radio info or anything like it used to. It shows the splash screen and then boots. It used to show radio info and version, etc.
Click to expand...
Click to collapse
I guess that means for those who do want to go the Android way, they need to do so from default HTC provided ROMs (or at least bootloaders/SPLs). You need to try to get into the Bootloader as already explained in this thread (which is the 4 coloured screen and NOT a customised splash screen) before you have any hope of rectifying things. There are good threads about how to recover from being stuck at the Bootloader so you'll need to do some searching and wiki reading.
As Flying Kiwi states, you should look here stuck in bootloader
Hello, and welcome myself to this wonderful forum.
Let me introduce myself:
My name is Mish , im a 100% dumbass
Also BIG! thanks for sh1tty cyan's wiki about flashing with dangerspl.
Let me tell you my story:
In a cold night, a boy tried to update his G1 to android 2.2 , updated dreaimg.nbh , rooted the device, installed recovery image . that boy was so excited his 1st android, his 1st up mod.
but that boy was upset, didnt wanted to get his update.zip installed because of the status 7 error. well done , he just looked into the cyan's bloody wiki and he found the magic archive called Danger SPL.
flashed it , rebooted it and stucked into G1 T-mobile Splash screen .. he was like . ah , allrite, i'l reboot and enter to recovery mode . but he cannot do that.
He was so anger . he kissed his keyboard with 2 gently strikes. and searched for hours for solutions but nothing found.
I dont have pages to write the whole story. Aka the end.
in other words, can i get my device working or should i give him wings to fly straight on the garbage can ?
Can you get into fastboot mode? Also i think in the instructions it tells you to flash the radio first. I could be wrong but several people have successfully rooted their device with the instructions given here on xda. Welcome to xda btw.
John
Hello John, i can't enter to fastboot mode or i dont know , it shows me just the T-mobile G1 Splash screen and nothing more, tried with Camera + Power, Volume + Power, Home + Power and still nothing . if you have any hints please share, regards.
Can you reboot holding back and power and get into fastboot?
nope , is stucked in G1 splash screen
I did the same thing and had the same problem - had to replace the motherboard. There is NO WAY to fix it except to replace the mainboard. Good Luck
Is my phone a goner?
I wasn't trying to root or modify my phone in any way. It started flickering and then went black. Now...
Phone does not power on. Not with power button or any combo (camera+power; home+power; etc).
No LED notification. Not even orange when charging.
Eventually starts in tri-color/rainbow/RGB Bootloader ON ITS OWN (no keystrokes). Sometimes after 1 min, sometimes after 20+. Once in Bootloader, it stays there. If it's plugged in and charging, the Bootloader stays on even after battery pull.
Bootloader says:
DREA100 PVT 32B
HBOOT-0.95.0000
CPLID-4
RADIO-2.22.23.02
Sep 2 2008
Serial0
Reformatted SD card and installed original SPL (renamed install.zip) and DREAIMG.nbh to the SD's root. When my phone eventually started in Bootloader (on its own), it went into the install phase, completed, and asked for reboot. I pressed the trackball (action button), it rebooted, and hasn't done a thing since.
mish12 said:
Also BIG! thanks for sh1tty cyan's wiki about flashing with dangerspl.
Click to expand...
Click to collapse
Cyan's wiki is one of the most well written, organized and constanly updated around. Don't blame wiki for something that you did.
Take a look at http://wiki.cyanogenmod.com/index.php?title=DreamangerSPL#Flashing_DangerSPL, how can anyone miss this?
Congrats on your new paperweight.
DUBsays said:
I wasn't trying to root or modify my phone in any way. It started flickering and then went black. Now...
Phone does not power on. Not with power button or any combo (camera+power; home+power; etc).
No LED notification. Not even orange when charging.
Eventually starts in tri-color/rainbow/RGB Bootloader ON ITS OWN (no keystrokes). Sometimes after 1 min, sometimes after 20+. Once in Bootloader, it stays there. If it's plugged in and charging, the Bootloader stays on even after battery pull.
Bootloader says:
DREA100 PVT 32B
HBOOT-0.95.0000
CPLID-4
RADIO-2.22.23.02
Sep 2 2008
Serial0
Reformatted SD card and installed original SPL (renamed install.zip) and DREAIMG.nbh to the SD's root. When my phone eventually started in Bootloader (on its own), it went into the install phase, completed, and asked for reboot. I pressed the trackball (action button), it rebooted, and hasn't done a thing since.
Click to expand...
Click to collapse
Do you have access to another battery? I would try that first. This is not a software issue, if new battery doesn't fix it... you may be better off getting another G1 of CL or Ebay (I hear of folks picking them up for less then $50 nowadays)
I've been having trouble with my Vibrant and with T-Mobile in limbo I picked up a N1 off ebay to hold me over. This thing is driving me insane!
The phone came with CM7 installed on it, but the person that shipped it to me didn't erase any of there stuff so I figured I would flash a fresh image on the phone to take care of things. I've flashed my Vibrant a dozen or so times and never had an issue. Flashed the N1 and it comes up with an X made of 4 different colored lines and a little lock at the bottom. I know some roms take a while to load so I let it sit for an hour. Nothing.
Since I've been trying everything I can find out how to recover the phone including all of the guides on the wiki. I'm at my wits end at this point. I can't get into clockwork at all on the phone. It gets stuck in the bootloader and if I select recovery it just takes me back.
I've got droid explorer running, and the phone shows up, but it doesn't show anything on the phone, no folders or files and won't let me load anything on to it. (it says it is, but then stays blank) I have no clue what to do at this point short of taking a sledge hammer to it. (obviously I'm posting this as I consider that to be plan B)
I don't need anything special, I just want a working phone. Is that really so much to ask for?
If ur Phone is running( means u can boot) try flashing cwr from rom manager and flash the rom again or try to hard reset the phone and then see ?
Firstly, I would start of by being more specific about what you have tried.
If you really have tried "everything", then there's nothing anyone can do for you.
I suspect you haven't tried "everything"...?
danger-rat said:
Firstly, I would start of by being more specific about what you have tried.
If you really have tried "everything", then there's nothing anyone can do for you.
I suspect you haven't tried "everything"...?
Click to expand...
Click to collapse
I'm sure I haven't, just what I found in the wiki
I tried the PASSIMG.ZIP and it failed
I tried Amon_Ra's Recovery and the only way I can get it to do anything is to tell it to flash in droid explorer and it just reboots and gets stuck. Now nothing is showing up file wise in droid explorer and I can't transfer the image onto the root.
When I could get into clockwork I tried flashing different roms but it would just go to a screen with the clockwork logo and get stuck.
amolji said:
If ur Phone is running( means u can boot) try flashing cwr from rom manager and flash the rom again or try to hard reset the phone and then see ?
Click to expand...
Click to collapse
I can turn it on to the screen with the multicolored X or the bootloader, that's it. How do I do a hard reset?
n25philly said:
I can turn it on to the screen with the multicolored X or the bootloader, that's it. How do I do a hard reset?
Click to expand...
Click to collapse
in the bootloader I think (dont take my rookie rooting words too serious) theres a hard reset menu under recovery. it will take you to another x and press volume up and power for the menu to pop up.
try fastboot a recovery image (either Amon Ra or CWM) and see if you can get back to recovery after that.
Well I'm assuming you already have a custom recovery since it came with CM and you've, as you said, flashed it (what exactly do you mean by that by the way? flashed another rom?). So all I can recommend is that you wipe a few times and try flashing a few different roms and hopefully one will boot. Not the best advice in the world but its always worked for me before and my N1 and my DEXT before hand when I've messed them up!
You still did not say what you flashed to your phone.
Anyways follow the restore to stock guide.
I don't know what this Droid manager thing is but don't use it. Install the sdk.....