Related
I successfully loaded WM6 on my Cingular 8125, but it had some weird issues (today screen didn't fully draw, ringtone screen wouldn't close, etc.) so I decided to go back to the stock ROM. But I thought I'd try a hard reset first and that's where I ran into problems. The screen stays white, but there's a constantly changing series of vertical colored lines that move all over the screen. I can't do a hard reset and can't get into the bootloader. All I get is the shifting white screen and ActiveSync won't see the device, but I get occasional USB bleeps/bloops when i plug the device in.
Any tips on recovering and going back to the original ROM? I've learned my lesson and won't fool with WM6 on my locked G4
Try turning your phone off, and then press and hold the camera button and then press the on button while still holding the camera button and that should put you in to bootloader mode. From there, download and flash the stock ROM from your service provider and see if that works. From your description of what it's doing though, it might actually be a hardware issue that just happened coincidentally at the same time you tried to flash a new ROM. Hopefully it's just software related though for your sake.
Software incompatibility can cause your AT&T Tilt (HTC 8925) screen to go "Black", without the ability to perform and can render the phone useless.."briking your tilt"
The following fix will return the phone to factory specs only if you were using AT&T ROM. This fix is NOT tested on Other ROMS:
1. Remove your SIM card.
2. Remove your Micro SD Card.
3. Do a Soft Reset.
4. Immediately when the black screen appears, press and hold the On/Off side button ( hold for 25-30 seconds ).
5. Wait for 1 to 2 minutes, until a message appears on its own, saying that the phone reboot is non-functioning due to installing incompatible software. It also asks you if you want to re-set the phone to original factory settings to press "send" ( They mean the button with the green phone picture on it on the bottom of the phone), or press any button to cancel the process.
6. Press the button with the picture of the green phone.
7. Wait for 2-5 minutes and the phone will re-set itself to factory specs.
8. Phone will shut down itself. Turn it on normally and start fresh.
Good luck!
I found this out the hard way. We should start a list of software that does it, heres the first that I found will black screen your tilt, do NOT use this.
Levenums taskbar battery meter
http://forum.xda-developers.com/showthread.php?t=277790
You will black screen and lose everything with it as I found out twice on my tilt. It loads at widows startup during the windows screen.
Another non compatible program!
please note that if you install "arabizer13bn277.exe" or any of its product on your Tilt YOU WILL brick the device and you will need to re-set it to factory ROM.
if u do factory rest
we will loose all the phone nos & information of contact
Im not able to sycn & save Telephone nos & notes on induvisale nos
How else can i save nos on comp
or should i get a new phone & then ask AT&T phone people to help me set it on the new phone
Please help
While this won't BLSOD (BLack Screen Of Death) your Tilt, it will definitely kill your GPS and should be avoided at all costs - Map4PDA.
If you install it and run it, it starts searching for your GPS and eventually hangs, requiring a soft reset to recover use of the phone. After a soft reset, the GPS no longer works. Too bad there isn't an option to manually specify GPS settings because it's a sweet GPS mapping program ala Google Maps that can switch between MS Live!, Google and Yahoo maps (plus one or two others I think...).
Man i hope this works!!!!
I got the black screen from flashing wm6.1 from htc e-club site. The new OS came up fine but when I restored my files with Sprite (only because PIM back up log couldn be found on memory card) the annoying Att animation starts but when the WM6.1 screen is supposed to come up screen goes black. Tilt WILL NOT hard reset with soft keys and stylus! I even attempted to re-flash 6.1 in hopes for a hard reset that way, but usb is even un-responsive! If this black screen reset you posted works, be looking for a donation from me!!!
Any other tips or suggestions would be greatly appreciated! I am new to all of this...but I have read, and read, and searched, and read, and have learned a good bit. But now I need HELP PLEASE!
rednekvolfan said:
I got the black screen from flashing wm6.1 from htc e-club site. The new OS came up fine but when I restored my files with Sprite (only because PIM back up log couldn be found on memory card) the annoying Att animation starts but when the WM6.1 screen is supposed to come up screen goes black. Tilt WILL NOT hard reset with soft keys and stylus! I even attempted to re-flash 6.1 in hopes for a hard reset that way, but usb is even un-responsive! If this black screen reset you posted works, be looking for a donation from me!!!
Any other tips or suggestions would be greatly appreciated! I am new to all of this...but I have read, and read, and searched, and read, and have learned a good bit. But now I need HELP PLEASE!
Click to expand...
Click to collapse
If you have a HardSPL, re-flash your Radio to a newer version. That can fix a black screen if you just upgraded your ROM. Just remember that you may need to try a few before it finally works.
Cant flash anything til I get it to reset.
As of now the phone is TOTALLY bricked! My pc doesn't even recognize it when I plug in usb. Really I'm getting two different screens. one is lit up but black, and the other is bars going down the screen Blk-white-blk-white...
I'm gonna try the steps above when I get home n pray for a miracle! I just had the screen replaed a month ago. I hate to lose her all over again! 8525n it for now!
I got the black screen from flashing wm6.1 from htc e-club site. The new OS came up fine but when I restored my files with Sprite (only because PIM back up log couldn be found on memory card) the annoying Att animation starts but when the WM6.1 screen is supposed to come up screen goes black. Tilt WILL NOT hard reset with soft keys and stylus! I even attempted to re-flash 6.1 in hopes for a hard reset that way, but usb is even un-responsive! If this black screen reset you posted works, be looking for a donation from me!!!
Any other tips or suggestions would be greatly appreciated! I am new to all of this...but I have read, and read, and searched, and read, and have learned a good bit. But now I need HELP PLEASE!
Click to expand...
Click to collapse
I have the exact same issue. I am trying the steps above, but no luck so far. Any tips?
Ok it seems to be working. Any tips on restoring my data that was on the sprite backup?
rednekvolfan said:
As of now the phone is TOTALLY bricked! My pc doesn't even recognize it when I plug in usb. Really I'm getting two different screens. one is lit up but black, and the other is bars going down the screen Blk-white-blk-white...
I'm gonna try the steps above when I get home n pray for a miracle! I just had the screen replaed a month ago. I hate to lose her all over again! 8525n it for now!
Click to expand...
Click to collapse
This is from the manual -
To perform a hard reset using device keys
1. Press and hold the left SOFT KEY and the right SOFT KEY, and at the same time, use the stylus to press the RESET button at the bottom of your device. (It helps to have three hands to do this part).
2. Release the stylus, but continue pressing the two SOFT KEYs until you see the following message on the screen:
This operation will delete all your personal data, and reset all settings to the manufacturer default settings. Press SEND to restore manufacturer defaults, or press any other button to cancel.
3. Release the two SOFT KEYs, and then press the green phone button on your device.
Warning! Your device will be set back to factory default settings.
It worked for me! It returned me to the WM6.1 I just installed!
asfoor said:
Software incompatibility can cause your AT&T Tilt (HTC 8925) screen to go "Black", without the ability to perform and can render the phone useless.."briking your tilt"
The following fix will return the phone to factory specs only if you were using AT&T ROM. This fix is NOT tested on Other ROMS:
1. Remove your SIM card.
2. Remove your Micro SD Card.
3. Do a Soft Reset.
4. Immediately when the black screen appears, press and hold the On/Off side button ( hold for 25-30 seconds ).
5. Wait for 1 to 2 minutes, until a message appears on its own, saying that the phone reboot is non-functioning due to installing incompatible software. It also asks you if you want to re-set the phone to original factory settings to press "send" ( They mean the button with the green phone picture on it on the bottom of the phone), or press any button to cancel the process.
6. Press the button with the picture of the green phone.
7. Wait for 2-5 minutes and the phone will re-set itself to factory specs.
8. Phone will shut down itself. Turn it on normally and start fresh.
Good luck!
Click to expand...
Click to collapse
I had the same exact dang problem about the whole thing about getting the new rom from e-club and using sprite to backup and then upon restore of my back up, i just got a blank screen. I did this trick here and it worked perfectly. The real trick is step 4 and 5. I did what step 4 said to do except i held on for 35 sec instead of 30. and then after that i just pushed the send key (green phone button) a couple of times and then just let it sit for the 1-2 min and the magic message popped up! I followed through with the rest of the steps and voila! It works!
P.S. Dont forget to put your sim card back in.
Anyone get positive result from this method ?
I'm not.
My Kaiser have a black screen after unsuccesuful ROM update, and I can't flash him anymore.
Because PC recognize it as Flash Device, but noone from ActiveSynch driver's does not approach for this mode.
Any solution, please ?
I bricked my tilt after upgrading to 6.1 and using sprite backup to restore my data. I fixed it by putting my tilt in to bootloader mode by holding down the camera button and using the stylus for a soft reset. Once in bootloader mode the usb port on the device worked and I was able to reflash the rom. I will use the new method to restore to factory setting without having to reflash the the rom.
i am having the same problem as supereri and rednekvolfan. did you guys ever figure it out?
Reset worked
Hi everyone.
I had the same issue - backed up data using Sprite Backup, upgraded to WM 6.1 then restored data using Sprite Backup and the custom Device Update file that Sprite Backup requested. The phone reset and then would show the initial ATT and 3G screens then black.
I used the modified steps outlined by live2c2morrow -that are a modification of asfoor's original post and they worked.
Black screen appeared - held the power button for 35 - 40 seconds, pressed the Green Send button a couple of times then waited - 5 minutes later I received the message that the phone failed to boot and was given the option to reset the phone to factory defaults.
The key is to be patient - the screen will appear eventually.
Also - the first few times failed and I think I was inadvertently pressing the PPT or wheel buttons on the other side of the device.
Thanks to everyone on this thread - I thought I ruined my phone!
Sprite Backup - upgrade
I am upgrading my Sprite Backup to version 6 and will try the restore again.
Started experiencing a strange issue with my tilt today..
When I soft reset it loads the Today screen, and then attempts to search for the contact 'wszx' (these keys are located next to each other). After this I can navigate the phone just fine using the touch screen, but the only buttons that work are the directional and center buttons located on the front of the phone, and the arrow keys on the keyboard. I cannot type at all using the keyboard, and pressing any of the other buttons does nothing (except the directional/center/Power). I also cannot Hard reset because the two soft-keys do absolutely nothing. I've hard reset in the past but it no longer works.
So am I SOL? I think I've tried everything.. and now I have a custom rom, etc on the phone and I have no way of getting it back to factory rom without the ability to hard reset.
Thanks for any help.
dam1en said:
Started experiencing a strange issue with my tilt today..
When I soft reset it loads the Today screen, and then attempts to search for the contact 'wszx' (these keys are located next to each other). After this I can navigate the phone just fine using the touch screen, but the only buttons that work are the directional and center buttons located on the front of the phone, and the arrow keys on the keyboard. I cannot type at all using the keyboard, and pressing any of the other buttons does nothing (except the directional/center/Power). I also cannot Hard reset because the two soft-keys do absolutely nothing. I've hard reset in the past but it no longer works.
So am I SOL? I think I've tried everything.. and now I have a custom rom, etc on the phone and I have no way of getting it back to factory rom without the ability to hard reset.
Thanks for any help.
Click to expand...
Click to collapse
Sounds like a hardware issue or simply a bad flash. Have you attempted to reflash the rom? Which rom are you using?
Well...
It wasn't working again this morning, but suddenly - out of nowhere - began to work properly. I'm stumped. If I ever figure out the exact issue I'll be sure to post back.
Thanks
Greetings,
I have same problem on my tytn...
Sometimes it suddenly starts working fine, but shortly it breaks again.
I have tried hard-reseting while it was working, but didnt help.
I think the problem appeared after charging my phone with a motorola v3 charger, so maybe it damaged my phone with over-voltage or something...
Anyway, if someone can suggest something i would be very grateful!
Hi I have exactly the same symptoms with my HTC Tytn II...when you power it on it starts typing letters (in my case CEDF). If the recording button is active it will start recording too. This happened suddenly and I haven't used any other charging apart from the usb and wall socket charger supplied with it.
All buttons (except front center key) and keyboard do not work. Any suggestions would be appreciated very much. This phone is only 8 months old.
Hi,
my Kaiser with dutty's WM6.1WWE ROM did the same this morning Yes I disabled the button 6 and stopped the voice recordings but all the hardware keys but few in the center of the keyboard are not responding. So I cant make or receive calls without taking the stylus out and touching the screen soft buttons andd that's pin in the ... while I am driving. I am using this ROM for almost a year now and I am extremely hapy (up to now) with its performance. When it all happened there were no activities on the phone - I woke up from a SMS notification (Yes I did receive an SMS from my bank) followed by repeting Voice Recordings. Any help will be highly appresiated! Thanks in advance!
keyboard problem
I am experiencing a similar problem with my stock tilt my keyboard does work however none of the text appears on the screen. I have tried hard reset and everything else I could think of, short of a clear storage reload. I would appreciate any help or suggestions from some of you more experienced users.
Bisonwill
anyone ever figure this problem out? im having the same thing happen now.
Same here
I've had it for a couple of weeks now.
I'm running WM6.1 from HTC (rom ver.3.29.422.1 from 2009-01-12) so nothing fancy here.
I even ordered and replaced the D-Pad and I replaced the keyboard (just the sticky part though). I totaly dismantled the phone and didn't find any issues with the cables.
Any ideas would be highly appreciated
Join the club!
This is crazy. My problem is exactly the same. I re-romed to the latest phoenix and it did not change a thing.
Help!
help....
any body here found a solution for the keypad/keyboard yet??? i have the same problem as you guys... any idea, thanks so much...
i have the same problem And there is something else. My Kaiser wakes up every 2 minutes - it's killing the battery. It works only for 6 hours now
Help
bump!!!
No more people with this issue or any solutions?
Pls! Help
ive joined the gang!
I decided to flash my cooked rom ive been working on.
i hadnt changed much in the kitchen and i think the flash has went badly.
it starts booting windows and where it should state "calibrate screen" it goes white and hangs there, buttons seem to respond by lighting up when pressed.
Now when i try to get it into bootloader or even hard reset it just doesnt work.
it just restarts the phone.
before this happened the backspace key hasnt been working for ages.
anybody got any ideas??
(lucky for me i have a backup kaiser!)
I'm having the same problem. Automatic wakeup, applications starting automatically, can't use keyboard, have to to use screen to use phone etc. I've hardreset using the clear storage method, reflashed a couple of times, but nothing helped. So here I am joining the club
If it's not a hardware issue, then try to flash another radio, many of the custom ROMs here doesn't include a radio, so if it's caused by a wrong radio, flash a new ROM without a radio doesn't help.
Check the Sticky for 'how to' if not aware.
PS: Check here for something need to know..
The question is.... how do I flash the device if I cant get it to go to boot loader and the OS wont boot properly !?
I think its an official Brick!
the really odd thing I've discovered is sometimes the OS leaves the loading screen on, and when it does if I press the FN and folder key, I get explorer up but its not responding... I haven't tried inserting a memory card yet to see if I can access that.
Danhargreaves said:
The question is.... how do I flash the device if I cant get it to go to boot loader and the OS wont boot properly !?
I think its an official Brick!
the really odd thing I've discovered is sometimes the OS leaves the loading screen on, and when it does if I press the FN and folder key, I get explorer up but its not responding... I haven't tried inserting a memory card yet to see if I can access that.
Click to expand...
Click to collapse
Try this:
1. Take out the battery from the phone.
2. Take out SIM card and SD card.
3. Press in and hold the CAMERA button.
4. Plugin to your computer using the USB cable, while keep holding press in the CAMERA button.
See does it enter the BOOTLOADER mode.
Once entered the BOOTLOADER mode, you can flash a new radio or rom right from there, in your regular way of running KaiserCustomRUU.exe.(Since you already have a HardSPL flashed on, otherwise a HardSPL is needed to flash first.)
Good luck.
Edit: If the power button and the camera button is still working, you can use the regular way of entering BOOTLOADER mode, and flash from bootloader mode or flash from SD card.
Originally posted by Manpreet @ www.sakajati.com
To enter in bootloader mode:
Simply Switch off your phone. Press and hold camera button and also press and hold the power button..You can remove ur finger from power button when phone is switched on but keep holding camera button until u come to bootloader …Now attach the usb to ur computer and do the flashing you normally do.
Click to expand...
Click to collapse
Thx for your suggestion:
I tried removing battery as sim and sd were already removed due to previous attempts in fixing!
so:
i removed battery (did not put back in), plugged in while holding camera
got nothing, so held power button at same time, the green light came on, then went off, and came back on again. but no bootloader.
i tried same procedure with battery in, and all i get is the OS loading up, no bootloader no matter how long i hold the buttons.
is there any other alternative method to get into bootloader (possibly involving other button presses)?
or any other ideas.
Really want to fix this as it was my "experimental" phone for cooking roms with.
Thanks again.
Suspect you have some hardware issue with the camera button. Can you ever take a photo with it?
Edit: Did you read through every post onthis thread:
MTTY (How to fix a bad ROM flash!)
If you tried that and still no luck, you can post your questions there. There are masters will keep an eye on that thread. And generally they only have time to look into their 'subscribed' threads, chances are they will not look into here.
Edit: Maybe the procedure I told is wrong, since I call from memory, check this:
dwny said:
If you have a bad flash....that's no reason to worry.
I haven't had to use MTTY to recover.
In most cases, if there's no issues with the Rom itself...you can pop out the battery and re-flash the same ROM from BootLoader Mode. This will also work if for some reason your computer crashes or loses power & restart during the FLASH.
If the Rom has issues.....the flash will not complete and the device will be stuck in BootLoader Mode. At this point,you must FLASH a FACTORY ROM!!
Pop the battery off 1st, power up the device, device will power up in BootLoader Mode, connect to pc & FLASH your devices FACTORY ROM. This will restore your device back to it's original out the box settings.
The above only works if the device has been put through the Hard SPL or SuperCID process.
I personally have never tried to flash a cooked ROM without unlocking any of my devices. From what I've read what others have experienced...the flash would just fail and they're stuck in BootLoader Mode.
Myself ... I've experienced bad flashes, bad cooked roms that I've cooked, lost power to a pc & had my pc crash during a flash. Listed above is how I've recovered. There is life after Bootloader Mode.
The only time you have to worry is if your device does not power up at all
As a public chef...it's your responsibility to set the parameters of your ROM! Meaning, Radio, HardSPL, program conflicts, etc.
You are not ultimately responsible if someone bricks their phone but if they pushed the issue, you could be hit with some form of liabilty because you failed on providing a simple Disclaimer that sets the expectation.
I hope I've been helpful.....
Click to expand...
Click to collapse
Edit again:
And try like:
Plug in USB first, and thenn press & hold Camera, Power button etc.
I remember once I read there is a way to enter bootloader without battery, just can not find the original again.
Hi
It's not the first time I flash my TytnII, but this time, I get worry about my phone...
I've tried to put the kaiser_wwe_shifu_v3.0 rom's.
According to doc, I've upgraded Radio and Hard SPL.
Radio is 1.70.19.09
Hard SPL is 3.29.
The upgrade of ROM was OK, but some stranges things appened therefore. The first boot, OK the device is configuring itself, and rebooting.
After the first reboot, the device is still "fresh installed"! So here we go another time to pre-configure it...(time, touch screen...)
After, it seems to be OK, but in fact, I see there's no more memory to completely startup the phone. Because the phone starts, but finally, a program (don't remember which one) says that it cannot start because lack of memory...)
I reboot, and since, me phone doesn't boot at all....
It display the startup page with radio , hard SPL infos, but no more, it seems to be completly block on these steps.
What could I do?
Thanks a lot
Have you tried to flash another ROM?
You can try this bij holding camera button while booting, you should see the tri-color screen. Connect it to your PC and try to flash again or another (maybe stock-rom?) ROM.
Good luck
No funny multi color screeen appears when pressing camera button while booting...
Can't connect a cd reader on it, and erase flash
thanks
Do a hard reset and see if that works, hard reset is hold down left and right softkeys and and hold in reset button with stylus until you get to a screen about resetting the phone, remember to back up any data on phone memory cos you will lose this after a hard reset
I want to second this problem.
After flashing the Radio to "KAIS_RADIO_ONLY_1.71.09.01" and installing PDA corners newest ROM, everything worked fine. The only bug was that when I wanted to turn off the device by holding the power button, after choosing the turn-off option, it just restarted.
Now the phone doesn't start at all. Seems as if there is no power from the battery, while there was enough charge in it. When I connect it to the power plug, the charging/power led turns almost red, never saw that before.
This is not my first ROM-update, but this is the first time I've encountered this problem.
I tried hard and soft resets, removed the battery, tried to connect it to the pc, nothing worked.
Any ideas?
Thanks.
Press and hold the camera and the power/ on buttons. While ho[ding both buttons, do a soft reset. Once in bootloader ( tri color ) flash your original stock rom.
What I already tried:
- hard and soft resets
- removed the battery
- tried to connect it to the pc
- connected in the power plug, nothing worked.
- tried the power button+camera+soft reset
I download the the same Rom....I I have the same problem.... I Reset with Pressing Camera and Power method....it went to the Hardspl screen and I load a new ROM...its working fine now.
hi there,
this morning, without any interactiom, i heard the vibration of my touch diamond restarting.(with original newest ROM from htc website that ran without any problem for several months). battery was about 80% yesterday evening.
but it wasn´t starting at all. after the HTC animation and the green windows mobile screen, it started again. after restarting for 20 minutes i took out the battery, put it in again and performed a hard reset as stated in the manual.
now, on the "rainbow" screen i get a message like
psoc diam stage_pvt 0x32
then i did the Volume-Up reset, and now i don´t even get the red version information in the lower right screen. as it doesn´t even start i cannot get an active sync connection.
any ideas? is my phone broken? i didn´t do anything special, and i wonder why it rebooted without interaction this morning.
any ideas what i can do?
thanks in advance,
jkersch
Mine started doing this about 2 weeks ago it woke me up in the middle of night while sleeping with its vibrator and start sound.
The only thing I have found is that my little reset button at the pen holder dosent work anymore. To do a hard reset i have to takeout the battery and then put it in, hold the volume key and enter key then power it to get it. Flashed by holding volume down and the power on, it hold for about 10min just enough to get the flash.
I managed to flash it once but it dosent help, it constantly reset at the thouch diamond screen. Some times i get to the green windows mobile screen.
As warrenty is out on my phone and ive given up and using another phone.
Same problem in a different thread
Have a look at http://forum.xda-developers.com/showthread.php?p=5279740.
install a new radio worked for me