3G not working but I've had some H reception - Tilt, TyTN II, MDA Vario III General

For a while now my 3G connection has not been working but I have full Edge reception and I have had some intermittent H reception. I have flashed the ROM, changed the radio and switched my SIM card but nothing has changed this.
Is the phone made to have 3G and H reception from the same chip, (most posts seem to say this is a hardware issue, that a microchip has burned out on the motherboard)
Maybe someone knows how to get the phone to turn off 3G but retain H reception?

H icon means HSDPA this is part of 3G. So there is no option to disable 3G leaving HSDPA active. But I can be wrong ;d
Wikipedia said:
High-Speed Downlink Packet Access (HSDPA) is an enhanced 3G (third generation) mobile telephony communications protocol in the High-Speed Packet Access (HSPA) family, also coined 3.5G, 3G+ or turbo 3G...
Click to expand...
Click to collapse
http://en.wikipedia.org/wiki/High-Speed_Downlink_Packet_Access
And I had similar problems, but they solved themselves . I think they was caused by lack of range ( I have H under the table, but over Edge only...).

It might help to diable HSDPA using a program like kaiser tweak.

Related

Connecting to UMTS/HSDPA using AT&T

I have noticed that when I am connected to the fast cellular internet the sign constantly switches between 3G to H. Like every 15 secondes.
It's not that the connection is dropping it's just it is always changes from 3G to H. I am on At&T and would like to know if it happenes to someone else.
As I read, At&T suppose to have an HSDPA and since I am in big cities like Chicago and Washington DC, if there is HSDPA it should exists in these cities.
So?? anyone using AT&T + KAISER knows what I am talking about?
should be worried?
i see this behavior all the time with my Kaiser, Trinity and Treo and never worry about it... most often the i'll see the "H" symbol when i'm tethering or downloading a file from a website or i'll see the "3G" or "E" if i'm in an area of town that doesn't have a strong signal... i don't worry about this behavior unless it affects what i'm doing, e.g., lose my internet sharing connection. just my 2 cents...
cortezzi said:
i see this behavior all the time with my Kaiser, Trinity and Treo and never worry about it... most often the i'll see the "H" symbol when i'm tethering or downloading a file from a website or i'll see the "3G" or "E" if i'm in an area of town that doesn't have a strong signal... i don't worry about this behavior unless it affects what i'm doing, e.g., lose my internet sharing connection. just my 2 cents...
Click to expand...
Click to collapse
Thank u for your fast reply. I know sometimes the signal changes to E or even G if there is no high speed connection around but it seems that the H and 3G just changes every 15-20 seconds in areas with high speed connection. does it also happen to you? or anybody else?
alonmalka1 said:
I have noticed that when I am connected to the fast cellular internet the sign constantly switches between 3G to H. Like every 15 secondes.
It's not that the connection is dropping it's just it is always changes from 3G to H. I am on At&T and would like to know if it happenes to someone else.
As I read, At&T suppose to have an HSDPA and since I am in big cities like Chicago and Washington DC, if there is HSDPA it should exists in these cities.
So?? anyone using AT&T + KAISER knows what I am talking about?
should be worried?
Click to expand...
Click to collapse
I actually consider you lucky. At work in Menlo Park, Ca. I rarely get a 3G or an H... But I spent a couple of weeks going to SF every day and there I saw behavior very much like you describe. For me it seemed to want to switch from 3G to H as I was doing some sort of access like e-mail read or a download. Though that is probably just anecdotal as I didn't really make a study of it; just something I noted.
Cheers.
i have the 3g/H switch happening constantly as well. could this connection issue have anything to do with the sms issues (issue being sms works randomly), or totally unrelated?
Yep...this happens to me too.
alonmalka1 said:
I have noticed that when I am connected to the fast cellular internet the sign constantly switches between 3G to H. Like every 15 secondes. It's not that the connection is dropping it's just it is always changes from 3G to H. I am on At&T and would like to know if it happenes to someone else...
Click to expand...
Click to collapse
I'm in the Chicago-North Suburb area and I see it change all the time too. I get a lot of HSDPA connections. From my understanding, this is a good thing!
Though I'm by no means an expert on HSDPA, 3G, UMTS or any of these, it's my understanding that HSDPA will give you data bursts of up to 5 times the connection speed of 3G/UMTS.
TEC
What it means on my 8525
Hi Guys,
Don't worry, you are not having signal quality or connection issues. On my 8525 (Hermes) the switch to H from 3G simply means the phone is using the data connection at the H (HSDPA) speeds. It shows 3G when data is not being transferred.
Yup. It's sort of like a combination power/hard drive light on a computer. When the "H" lights up, data is being read and written over the high speed network. The "3G" means the high speed network is available, your just not sending or recieving at the moment. At the slower EDGE speeds, the "E" is just a power light, showing the network is available, but no indication when you are sending a receiving data over it.
Someone correct me if I'm totally wrong, but here are my thoughts:
The H would be displayed when the device is accessing HSDPA or HSUPA. The D stands for download and the U stands for upload, right? But AT&T only has HSDPA right now, and not HSUPA. So when you're in an HSDPA area and browsing the web or sending and receiving emails, when the device is receiving information (downloading), it's on HSDPA and the "H" is displayed. But then when it needs to send information (uploading), since there is no HSUPA signal it switches to 3G and the "3G" is displayed. Hence the constant switching on the display as the device sends and receives data.
Someone please give me a gold star, or tell me I have no idea what I'm talking about!
Here's a GOLD STAR!!
KCMatt said:
The H would be displayed when the device is accessing HSDPA or HSUPA. The D stands for download and the U stands for upload, right? But AT&T only has HSDPA right now, and not HSUPA. So when you're in an HSDPA area and browsing the web or sending and receiving emails, when the device is receiving information (downloading), it's on HSDPA and the "H" is displayed. But then when it needs to send information (uploading), since there is no HSUPA signal it switches to 3G and the "3G" is displayed. Hence the constant switching on the display as the device sends and receives data. Someone please give me a gold star, or tell me I have no idea what I'm talking about!
Click to expand...
Click to collapse
Not that I'm an expert either but THIS WOULD EXPLAIN IT!
Thanks
TEC
If you see the H then you are using HSDPA, if you see the 3G icon then you are using UMTS. The difference is speed and the fact that if you see the H icon it means you can use voice and data at the same time.
I can stream live TV from my Media Center using WebGuide (free) and as long as I have the H icon I can talk on the phone at the same time I'm watching TV but if it switches to 3G I loose my data connection until I hang up the phone.
Mine mostly stays on H but swithces to 3G when the HSDPA signal is lost. HSDPA isn't avalible every where that 3G UTMS is.
Also HSDPA is 3.5G and UMTS is 3G. Meaning with UMTS you can get downloads of 384 kbps to 768 kbps and with HSDPA you can get from 768 kbps to 1mbps.
This is how it is supposed to work kids...
The H only shows up when you are using HSDPA. HSDPA would kill your battery in no time if it stayed connected all the time. your phone is smart enough to only use HSDPA when it is actually sending/receiving data. Think of it as a power saving feature.
I'm in cleveland and i just see an "H" all the time... FWIW...
Jason Lee said:
your phone is smart enough to only use HSDPA when it is actually sending/receiving data.
Click to expand...
Click to collapse
But it only uses HSDPA when it's RECEIVING data, not SENDING. That's what HSUPA would be for (if AT&T had it yet). Right?
High Speed DOWNLINK Packet Access
High Speed UPLINK Packet Acess
KCMatt said:
But it only uses HSDPA when it's RECEIVING data, not SENDING. That's what HSUPA would be for (if AT&T had it yet). Right?
High Speed DOWNLINK Packet Access
High Speed UPLINK Packet Acess
Click to expand...
Click to collapse
That is correct. HSUPA should be coming soon according to Engadget: HSUPA
KCMatt said:
Someone correct me if I'm totally wrong, but here are my thoughts:
The H would be displayed when the device is accessing HSDPA or HSUPA. The D stands for download and the U stands for upload, right? But AT&T only has HSDPA right now, and not HSUPA. So when you're in an HSDPA area and browsing the web or sending and receiving emails, when the device is receiving information (downloading), it's on HSDPA and the "H" is displayed. But then when it needs to send information (uploading), since there is no HSUPA signal it switches to 3G and the "3G" is displayed. Hence the constant switching on the display as the device sends and receives data.
Someone please give me a gold star, or tell me I have no idea what I'm talking about!
Click to expand...
Click to collapse
Perfect.!! Downlink = Downloading (HSDPA).. Upload data by 3G as AT&T is not supporting Uplink = Uploading (HSUPA)... smart one..
I'm not sure it is that simple...
I live in Jacksonville an i neverget an "H" except when i used shap's rom on my 8525; however, i get speeds from 600 to 980, so is this extremely fast UMTS, or is Cingular just inconsistant with their labels?
exzist78 said:
I live in Jacksonville an i neverget an "H" except when i used shap's rom on my 8525; however, i get speeds from 600 to 980, so is this extremely fast UMTS, or is Cingular just inconsistant with their labels?
Click to expand...
Click to collapse
I also live in Jacksonville and found with the Tilt that I was only seeing the
3G icon and never the H icon until I installed KaiserTweak and set the HSPA option to enabled. Now I get the H icon but only during the data connection being active (e.g., sending a URL request and receiving the page load). The icon then turns to 3G when the Tilt sits "inactive."
Also just because you don't see the H for HSDPA doesn't mean its not working unless the REGISTY has the correct setting you will not get the H icon. the place is HKLM>Drivers>RIL>EnableHSDPAIcon = 1 (sometimes default is 0 which means you won't see the H icon)
Since my last posts on this topic, I now have my Tilt!
I am confused- why would AT&T not enable the "H" icon? If you are using HSDPA (and soon HSUPA), wouldn't they want you to know it?
Maybe they are afraid it will confuse people. They just want to market "3G" and people to understand it and see that icon, whether they are on UMTS or HSDPA/HSUPA?

3G vs H confusion

I did the kaisertweak to enable the H network or whatever (yes i don't understand it)
the network still says E or 3G . It said that all the time, for the last few days.
Then I was messing around trying to get this gps to work in google maps and I noticed it switched to H. but now it's back to 3G. is this all normal?
Ive noticed that too..
no idea what it means
what operator are you with in what country
check with them to see if you have hsdpa reception my hsdpa is enabled but since i dont have coverage i stay at 3g
hsdpa is a better version of 3g
its often called 3.5g 3g+ or mobile broadband so basically all the twaek is is to let your phone get the faster connection but only if your operator has the signal to do so
The H icon (HSDPA) is a step up from 3G it allows anything up to 7.2Mbs transfer but the HTC instead of contantly allowing this to be active thus creating massive battery drain only allows it when a data connection is active and data is being transferred any other time and you will only get G, E or 3G
3g alows ypou to have video conferences but H mean HSPD fast internet 3,6Mbit or 7.2Mbit depands that the difference i belive.
exactly just because you enable it doesnt mean you can recive it
I turned hsdpa with kaiser tweak also. I noticed it will only connect to hsdpa when transferring data (IE, emails, weather, ect.). Otherwise it will go back to 3G when on the today screen, or offline tasks. I guess its to conserve power?
Maybe thats what your seeing?
ok thanks, looks to be normal =]

o2 - NO 3G???

guys,
i just transferred from orange to o2. i have no 3g now?? i used networ wizrad and got the settings from o2 but still no joy
i have HK official wwe rom and there is no 3g option in comm manager either
can anyone help?
did you try running connections setup? or adding the 3g to comm manager with tf3d config to see if it is on?
yes i ran connections setup and o2 sent me the config.
i cant fiund the wsay to add 3g to comm manager in td3 flo adv??
yes 3g is enabled, just doesnt work or never active even in good signal areas, nothing! i either have H or E next to my reception
patterns said:
yes 3g is enabled, just doesnt work or never active even in good signal areas, nothing! i either have H or E next to my reception
Click to expand...
Click to collapse
H? Oh dear... does someone wana tell him :/
I've been curious about this too. O2 doesn't have a 3G license, which is why they used the Jap technology i-mode (which as we know flopped). So where is the iPhone's 3G coming from? I think it's from '3', but I'm not 100%. So if you're not in a '3' coverage area I would guess this is why you don't reception on this band.
adamdon89 said:
H? Oh dear... does someone wana tell him :/
Click to expand...
Click to collapse
LOL (H) = HSPDA
HSPDA=7.5Mbps Approx making it a shed load faster than 3G
High-Speed Downlink Packet Access (HSDPA) is a 3G (third generation) mobile telephony communications protocol in the High-Speed Packet Access (HSPA) family, which allows networks based on Universal Mobile Telecommunications System (UMTS) to have higher data transfer speeds and capacity. Current HSDPA deployments support down-link speeds of 1.8, 3.6, 7.2 and 14.4 Mbit/s. Further speed increases are available with HSPA+, which provides speeds of up to 42 Mbit/s downlink.
robbed form wiki as im lazy!
adamdon89 said:
H? Oh dear... does someone wana tell him :/
Click to expand...
Click to collapse
im sorry, i LOL'd when i read that.
I didn't even notice the H in his post LOL. Strange how he either gets GPRS or HSDPA though, and never any 3G.
yes this is strange - well at least it explains it. i put my 3 sim in and i get 3g straight away, oh well i can connect to internet anyhow so.... all is good
thanks for help guys

G vs 3G

I can't seem to figure out why sometimes I get a G connection vs a 3G connection based on the radio icon in the notification bar. Does anyone know what the difference is? G seems to be much slower then 3G.
G stands for GPRS which is a 2G connection and doesn't use the 1700MHz spectrum like 3G (HSPA) does. There are several reasons why your phone would switch between GPRS and 3G. Signal strength and 3G coverage area is limited in the US for TMO is the most common. Certain types of electronic equipment can interfere with 3G as well.
Thanks for the info, I wasn't aware of GPRS. Typically I get E (EDGE) or 3G but inside my office I get GPRS, chances are it's the equiptment. Explains why my connection is so slow inside.

Suddenly no 3g, always H?!

My carrier had some little problems during the past weeks, aparently they were working on something. I sometimes, for short periods, did not have data connection or no servic at all. Now the problems are gone and a speedtest today showed that at my home, the download speed went from an average 1 Mbit to over 5 Mbit!
However, the H symbol won't go away anymore! It used to switch to 3g when not data was transferred. I assume that this will influence battery life.
Is there anything I should be worried?
From what I recall, H is faster than 3g, as long as your in a good signal area, the H will always be visable, it will only drop down to 3g if the area your in has no H signal... and if there is no 3g it will drop to a 2g signal... simples, having the H does not meen that data is being transfered!
I am aware of the different speed levels, what I experience now is that the H symbol stays all the time, whereas it used to change to 3g when idling even in areas with very good reception...
GMH24 said:
I am aware of the different speed levels, what I experience now is that the H symbol stays all the time, whereas it used to change to 3g when idling even in areas with very good reception...
Click to expand...
Click to collapse
Wait, I don't get what you're saying. Let me clear it up:
Very good reception = H
Not so good reception = 3G
You want to see H (means HSDPA which is a a type of 3G data, but it's faster).
MrSimtang said:
Let me clear it up
Click to expand...
Click to collapse
Okay, I'll try that too!
I live in an area with very good reception and therefore the phone used to switch from 3g to H whenever data was transfered and back . Now, however, it stays on H all the time and does not switch back to 3g when no traffic occurs.
It is just a change in the pattern my phone behaves so I wanted to get some info on that...
Hi, it's your phone doing what it should by seeking the best signal.
H refers to HSDPA which is based on UMTS (3G). Consider it a 'turbo' version of 3G. It's sometimes also referred to as 3G+ because it's faster then 3G but not really 4G technology. The tower in your area most likely got upgraded to HSDPA that's why you don't see the 3G icon anymore.
Sent from my GT-I9000M using XDA App
Not correct, he mentioned that his phone was using H on demand before, so the capability was there already.
The problem is that H mode uses more battery than 3G, which is why it normally only switches to H during data transfers instead of continously being on.
Possibly your provider made a change which forces your phone to stay in H mode. On hardcores homepage (see speedmod kernel thread) he describes a method to manually deactivate H mode if you want to play with it.
Hope that helps.
Sent from my GT-I9000 using Tapatalk
seems to be the explanation... Suddenly I have ~6 Mbit, so almost unsurprisingly there had to be a catch
as for disabling H, it would be permanently so not quite an option. I guess, I'll have to live with it but nevertheless I'll call customer support..
Hspa and 3g are actually different technologies, but can be used on the same site and freq. If you have noticed that your phone is nowdays all the time showing H ( hspa ) and not in 3g like before it means that your carrier has expanded their hspa features and capacity of the network on that area. Main difference between these two tech is of course the speed and how network resources are shared between the users. In 3g you have dedicated ones, but speed limited and in hspa you are sharing the resources between other ones under that cell area. hspa is good if you are near by the cell and there is not too many users from battery consumption point of aswell from througput point of view, 3g is better if you are on the cell edge due to dedicated resources reserved only for you. Main point is, battery consumption of your phone depends mainly how you use your phone ,what kind of applications you have and how often those are connecting/contacted by the network.
Browsing in 3g sucks!
Sent from my GT-I9000 using XDA Premium App

Categories

Resources