over the past few weeks some of the buttons (namely left soft key, up and left) have stopped working, i've tried numerous roms just incase but it's definatley a hardware issue, now, i've dismanted the phone using the diamantos guide to see if anything jumps out at me, gave the phone a damn good cleaning whilst i had the chance, put it back together....but nothing, everything seems to be in order, all components in their rightful place but i still cant work it out, does anyone know if this is a common problem or if theres a fix as i've been unsuccessful in my searches.
actually, i just found the solution and it worked a treat, thanks anyway people.
btw, if anyone would like to know what i did then i'll be more than happy to share the solution.
Hi godofwap,
I have the same problem with a trinity I bought used. Tried to stick some papers under the buttons but that didn`t help so I`m very curious how You managed to get them working again. Hope You find the time to write a short notice.
Have some fine days,
FlyBy_1
ok, no problem, heres what i did.
before you start please be aware that this is a very delicate procedure and you should take care as this may naff up your beloved trinity.
ok, i first disassembled my trinity using the dimantos guide located here http://forum.xda-developers.com/showthread.php?t=311463,
now, when you get to the keyboard / button pcb take it out if, you look closely you'll notice theres a thin adhesive plastic cover covering the metalic buttons, very very carefull peel this back (i used a sharp knife to get to it), making sure not to completely remove it, try to only expose the underneath of the buttons in question, you'll see that the buttons come away with the plasic leaving the underneath exposed, now, using a cotton bud and some lightly applied alcohol clean the contacts then when all is done, replace the plastic and make sure its firmly pressed back down you may notice it making a different, kind of sharper clicking noise when depressed than before meaning its worked, repeat for all buttons.
i think whats going on here is the gum or glue from the plastic film has "leaked" if you will, onto the plates meaning theres no contact from the buttons, this would also account for the very slight change in sound when you now press the button.
i found this info here http://forum.xda-developers.com/archive/index.php/t-289737.html
Nice find mate; sounds like a solution for my problem cause when I got my phone the first I had to do was to disassemble and clean the heck outta it, there was dust everywhere as if the old owner had laid it on the moon for a week. But who thought the buttons are actually separatable... strange technique.
Thanks for the hint, at least now I´ve got something to do over the holidays at my parents-in-law
Once again thanks for Your hint.
The problem with mine was actually not dust and stuff between the two halves but too much pressure by the former owner.
After I had separated the plastic film from the board I saw that there were very deep dents where the pick of the metal discs had pushed the soft pcb material down. So I cleaned them anyway and then reapplied the film with an offset of just a fraction of a millimetre so they make perfect contact with the pcb again.
Every single button again works perfectly now
Related
I remembered that I had left my XDA IIi in my friend's car as I was leaving, so I asked him if he could open his car and pass it to me. Before my eyes he makes this huge fumble, like a bar of soap in his hands, and it comes crashing to the concrete floor!! :shock: :x
Apart from a few scuffs and scratches it seemed ok, until I tried to use the standby button. There was no click to it, and it only works now and again if I press it in the right place with enough force.
So I dismantled it to take a further look, and I can clearly see that the micro switch is broken.
Has anyone attempted to unsolder one of these? Looks a little too dodgy to me with the multi-layered board. As I don't use the 'tape recorder' button, I could swap it for that one if it was possible.
Such a shame for such small damage. Any ideas what I should do?
tia
guys I have problem with my phone's screen, the upper part of the screen during portrait mode is no longer responding to the right spot. but the rest its ok...anyhelp?do I have to change my LCD? I even had it hard reset which gives me a bigger problem, a Align Screen menu pops out and I could not align it....anyhelp????
looks like you have defective digitizer screen, try to take apart and reseat the LCD connector. maybe it'll help.
last resort, change the digitizer screen.
yes, I think that's the same problem that i've been facing since last year :-|
any I dea how could that be happens ?
or is there any way to do it without bricking the device ?
welll....
I am looking at the possibility that it needs to be stripped down and cleaned! dirt could be causing the issue around the edges by applying pressure to the digitizer!!
does anyone know of any toolkits you can get to take this thing apart I am not too confident with my kitchen knife and chisel....
Probably on this forum somewhere...
(edit : I just did a bit of pushing down and hooking a piece of card around the edges of the screen and it seems to be working fine however this can be temporary...)
There are guides in this forum to taking an Alpine to pieces completely: I had to change my screen recently and it can easily be done before the backup battery has run out of juice.
If the digitiser part is behaving erratically you cna just purchase a new digitiser for about £4.95 off ebay, rather than fork out around 30-40 for a new screen.
TOols you'll need are small screwdrivers and a small set of torx screwdrivers.. again a search will tell you what size (I have a pack of t5 6 and 7 and cant remember which it is - it's the same pack you buy for disassembling mobiles)
Joe
Hi guys, i'm a big fan of this site, and I'm glad Im part of it since i can use you guy's great roms and tricks. But I have a big problem with my tilt now and I wanted to see if some of you could help me with it. I bought my tilt from a friend with a broken screen, i bought and replaced the screen myself, but after a day or two, the backlight for the screen wouldn't work. The only working solution i found was by squeezing the phone and pressing on the lower left corner above the green call button so the screen wouldnt turn on while i pressed it. I decided to open it, and i put a piece of paper above the connection of the screen and the flex, and this worked for a while. But ever since, i always have to keep putting in new pieces paper or plastic to keep pressure on the connection for the lcd, i was wondering if you guys would happen to know what the possible cause is. And it is hard because when i put those pieces of papers, the call button on the front has so much pressure that it is permanently pressed. I dont know what to do now, i don't know if i should just give up trying to fix my tilt or to just buy a new one. Hope someone can help me thank you.
damn...41 views and no replies....im guessing i should start looking for a new phone
A thorough clean needed
How about carefully cleaning the flex and connector using contact cleaner? If a connection surface isn't perfectly clean, often pressure is needed to push the terminals through the tiny film of grease (eg from fingerprints).
I'd say you bought a bad quality LCD that has a wacky contact inside the module...
im going to buy contact cleaner..if that doesnt work then it's probably a bad lcd like u guys said even though i paid 100 dollars for it ...thank you very much for the replies
ReYCangri said:
Hi guys, i'm a big fan of this site, and I'm glad Im part of it since i can use you guy's great roms and tricks. But I have a big problem with my tilt now and I wanted to see if some of you could help me with it. I bought my tilt from a friend with a broken screen, i bought and replaced the screen myself, but after a day or two, the backlight for the screen wouldn't work. The only working solution i found was by squeezing the phone and pressing on the lower left corner above the green call button so the screen wouldnt turn on while i pressed it. I decided to open it, and i put a piece of paper above the connection of the screen and the flex, and this worked for a while. But ever since, i always have to keep putting in new pieces paper or plastic to keep pressure on the connection for the lcd, i was wondering if you guys would happen to know what the possible cause is. And it is hard because when i put those pieces of papers, the call button on the front has so much pressure that it is permanently pressed. I dont know what to do now, i don't know if i should just give up trying to fix my tilt or to just buy a new one. Hope someone can help me thank you.
Click to expand...
Click to collapse
While replacing the screen you might've shorted something which would then only allow certain function by appling abnormal pressure.
hi,
my touch diamond 2's touch screen stop working randomly ( i think that i applied too much pressure on 1 spot for too long). I can see the touch screen dots on the area. I am just wondering if I were to repair this, would i be replacing the DIGITIZER or the TOUCH SCREEN.
Thank you soo much
warranty might cover that. It might not be your fault
I have decided to fix the part myself since I do not wish to ship the part to their location in the US. Any idea if its the digitizer or the LCD screen that i should be replacing?
jasonngu1991 said:
I have decided to fix the part myself since I do not wish to ship the part to their location in the US. Any idea if its the digitizer or the LCD screen that i should be replacing?
Click to expand...
Click to collapse
Search the Wiki, there are dismantle instructions.
I had the same on my display, and was able to move the dark spot to the edges where it disappeared.
I moved it with scratching it with my nail very gently applying some pressure.
In Europe HTC offers a pickup and return warranty, is that different in the US? If it is the same I would send it in to HTC for replacement, since it might happen again pretty soon....
I already have 3 screens replaced :-(
jason, did u manage to fix this? i have the exact same problem and pushing the "bubbles" towards the edge of the screen didn't help. my screen is still unresponsive..
mercurialcc said:
jason, did u manage to fix this? i have the exact same problem and pushing the "bubbles" towards the edge of the screen didn't help. my screen is still unresponsive..
Click to expand...
Click to collapse
Try applying duct tape to it repeatedly until you get it back.
Yes, both
I recently replaced the Touch Screen on my Diamond 2. Same problem; spots that "stick" in the middle. I used to solve this by running both my thumbs down the sides of the screen to "puff up" the low areas in the middle.
The part you want is actually called a "Digitizer Touch Screen" on eBay, cheap too. Prepare to spend about 2 hours fiddling with very tiny screws, connections and glue to tackle the job.
The hardest part for me was actually getting the Touch Screen to work; it seemed to be calibrated in mirror-image AND turned 90 degrees sideways, which made getting to the calibration functionality an extremely frustrating experience. I spend another 3 hours on that, but now I've got a perfect phone again, since I ordered a new case as well. No use taking the entire phone apart and then rebuilding with a molested outer shell...
maybe you should reset it
Working Solution Till Now
Hello Friends,
I have TD2 mobile and today I had same issue. I was thinking it was because of the weather or some.
I remember it did happend several time before, but when I restart the device several time it does work. So I was ignoring.... But today it did not work.. looks like going toward end... So I did soft and hard reset without and that did not helped me.
So I switched off the mobile, "heated" the touch screen gently with my hand for 1 min and started the mobile again and it worked for me .
Not sure if this is a solution, but will work.
May be I will contact Service Center here in Hyderbad and see what is wrong here?
Hope this will help you all...
Thanks.
Solution
Okay, I've just had this problem with an HTC Touch, and I think this works with any HTC that has a "digitizer" rather than an all-in-one touchscreen (I think newer phones have digitisers).
I'm not sure if this will always work, but I've just done it - sometimes the inactive touch screen is "broken" because the layers are stuck together (so the phone can't tell where the touch is, hence unresponsive). With mine, I looked at the screen side on and could see a kind of "oily" patch in the light.
The solution is to get masking/gaffa tape - the very sticky brown one. Stick it down on the screen/digitizer and then keep pulling it off - this pulls the layers from each other. I kept repeating this lots before it worked - and in the end I pulled the top layer completely off (I think you should pull from the top of the phone, as the layers need to be attached at the bottom of the screen/digitizer). Once it pulled away, I gently lay it back down (after panicking!!) and hey presto it started working again.
Good luck!
Digitizer replaced but still not working
The touch screen on my Touch Diamond2 stopped responding to my touch (or the stylus) and I tried everything including removing and replacing the digitizer bus just in case the connection was the issue. But all to no avail. Finally I decided to replace the digitizer (touch screen)
The problem for me is that it made no difference. The new digitizer doesn't respond to my touch either. The problem is apparently somewhere else.
If anyone has encountered this problem and has a solution I would be grateful to know what it is.
Thanks in advance
Replace the Touch Diamond2 Digitizer touch screen.
I recently replaced the digitizer (touch screen) on my HTC Touch Diamond2. Since I found on the net, no instructions for replacing the actual digitizer, I thought I might include some here.
It was relatively easy to fit. The only difficulty I encountered was a lack of information about how to actually remove the old one. The various instruction sets found on the web all stop once the screen is removed. But the digitizer is not covered by these instructions. The digitizer is bonded to a thin glass immediately under your screen protector (if you have one fitted) and after the screen is removed following instructions you will find on the net, the digitizer and the thin glass sheet that it is bonded to must be prized off from the front of the housing. The digitizer separates from the glass easily, but the glass is securely bonded to the housing with a silicon glue. It must be prized off by gently lifting a corner and applying a little upward pressure allowing the glue to slowly and gently let go. Don't be surprised if the glass breaks during the process. Once off it is a simple matter to press the new one in place. Just remember to start by slipping the connector bus (cable) through the narrow slot between the metal outer housing and the inner components. I used a set of tweezers to poke it through. DO IT FIRST before pressing the digitizer into place.
Okay, as I said the process was easy and took about 15 minutes all up.
prabhat said:
Hello Friends,
I have TD2 mobile and today I had same issue. I was thinking it was because of the weather or some.
I remember it did happend several time before, but when I restart the device several time it does work. So I was ignoring.... But today it did not work.. looks like going toward end... So I did soft and hard reset without and that did not helped me.
So I switched off the mobile, "heated" the touch screen gently with my hand for 1 min and started the mobile again and it worked for me .
Not sure if this is a solution, but will work.
May be I will contact Service Center here in Hyderbad and see what is wrong here?
Hope this will help you all...
Thanks.
Click to expand...
Click to collapse
i tried this and worked for me .
i removed the screen protector and switched off the mobile and heated the screen with my thumb and it worked again
thank you prabhat
and i'm using Topaz touch diamond 2
with photon ROM 1.6
Shoofty said:
I recently replaced the digitizer (touch screen) on my HTC Touch Diamond2. Since I found on the net, no instructions for replacing the actual digitizer, I thought I might include some here.
It was relatively easy to fit. The only difficulty I encountered was a lack of information about how to actually remove the old one. The various instruction sets found on the web all stop once the screen is removed. But the digitizer is not covered by these instructions. The digitizer is bonded to a thin glass immediately under your screen protector (if you have one fitted) and after the screen is removed following instructions you will find on the net, the digitizer and the thin glass sheet that it is bonded to must be prized off from the front of the housing. The digitizer separates from the glass easily, but the glass is securely bonded to the housing with a silicon glue. It must be prized off by gently lifting a corner and applying a little upward pressure allowing the glue to slowly and gently let go. Don't be surprised if the glass breaks during the process. Once off it is a simple matter to press the new one in place. Just remember to start by slipping the connector bus (cable) through the narrow slot between the metal outer housing and the inner components. I used a set of tweezers to poke it through. DO IT FIRST before pressing the digitizer into place.
Okay, as I said the process was easy and took about 15 minutes all up.
Click to expand...
Click to collapse
Thanks for the heads up on the glass part mate. Just replaced my TD2 digitizer too. Kinda freaked out at first when the glass split.. haha
Anyway, just wanna 1 more info. When removing the old digitizer, it'll be easier if the front housing was heated first (with a hairdryer on full or a heatgun) to soften the glue. It'll be easier to remove afterwards.
Word of warning though. Only head the housing when REMOVING the old digitizer, DO NOT use this method when applying the new one. The digitizer dies because of heat. Heat is what causes the newton rings issue.
Shoofty said:
The touch screen on my Touch Diamond2 stopped responding to my touch (or the stylus) and I tried everything including removing and replacing the digitizer bus just in case the connection was the issue. But all to no avail. Finally I decided to replace the digitizer (touch screen)
The problem for me is that it made no difference. The new digitizer doesn't respond to my touch either. The problem is apparently somewhere else.
If anyone has encountered this problem and has a solution I would be grateful to know what it is.
Thanks in advance
Click to expand...
Click to collapse
I have the same problema with my Diamond2. I have also changed the digitalizer with no success It is still not responding to any kind of touch.
Shoofty, did you manage to fix yours?
Thanks in advance,
Javier
Fixing TD2 touch screen
TD2 touch screen is a common problem I guess.
Symptoms are :
1- Touch screen does not respond sometimes
2- You can see a grease like layer under the touch screen
3- Sometimes if you look closer to the screen at some part you can see a a liquidized small area.
Solutions:
1- If you see the liquidized dot on the screen turn off the display and try to rub it with your finger until it disappears. turn it on again and try if it works. I guess heating with the finger as other peeople here suggest does the same thing. However this is a temporary solution. Your touchscreen will die at some date. I used my TD2 for 8-9 months using this method. But at the end touchscreen died.
2- Replace the digitzer or complete frontcover. Actually this might be easier than you think. I replaced mine in half an hour. I bought a front cover which includes the digitzer (http://www.ebay.de/itm/Original-HTC...zer_Ersatzteile_Werkzeuge&hash=item4cfe6f78dc) and openning tools from ebay. Dimanıond 2 disassemble and assemble videos on youtube were very helpful. I strongly suggest to buy the complete frontcover (inc digitzer). It makes replace process much easier and gives the device a brand new look. My old front cover was worn from the corners (which is also very commpn problem of TD2). Now it looks brand new. No strach on the display and body.
Thnks Ozkarah.
I happened to realize that, surprisingly, the touch screen of my HD2 started working if I heated it up with a hairdryer. So, I think something else is wrong beyond the touch screen, probably the connector to the main board of the mobile. It might expand once it is hot and that is why it starts working. In any case, I think that is beyond repair
HTC screen calibration
2Fresh said:
I recently replaced the Touch Screen on my Diamond 2. Same problem; spots that "stick" in the middle. I used to solve this by running both my thumbs down the sides of the screen to "puff up" the low areas in the middle.
The part you want is actually called a "Digitizer Touch Screen" on eBay, cheap too. Prepare to spend about 2 hours fiddling with very tiny screws, connections and glue to tackle the job.
The hardest part for me was actually getting the Touch Screen to work; it seemed to be calibrated in mirror-image AND turned 90 degrees sideways, which made getting to the calibration functionality an extremely frustrating experience. I spend another 3 hours on that, but now I've got a perfect phone again, since I ordered a new case as well. No use taking the entire phone apart and then rebuilding with a molested outer shell...
Click to expand...
Click to collapse
Hi,
I have same problem when I changed new screen (screen is calibrated in mirror-image AND turned 90 degrees sideways).
Could tell step by step how you get your screen calibrated?
Thanks
Hi, I dropped my phone by accident and unfortunately, it fell on the volume key which is now bend in the middle and stuck pushing vol up.
I can push volume down but the key is stuck with volume up and the phone would do that at random. For example, at some point during a call it would go to maximum volume automatically, which is super annoying.
Does anyone have experience with replacing hardware parts of the Zenfone 8? I watched this tear down video , it looks kind of easy to disassemble. However I am not sure if I can reach the volume key without removing the main board. Also, not sure if will be water proof after reassembling (guess not, but no problem).
Any tips? Thanks everyone!
I tried searching a bit but couldn't find any Zenfone 8 buttons (though maybe buttons from other phones could work). What I found instead is a complete frame that does come with the buttons attached to it, so you could either transfer the whole phone internals to it, or try removing the button to put inside your original casing. (I think the second option would be easier since the battery is glued down pretty solidly)
Anyways, here is the link: https://www.aliexpress.com/item/1005003661617745.html
I think it will not be water proof after you open it, so you should also consider getting a new seal. (Consider that I have never openned my zf8 lol so I am not pro). But from what it looks like, it will most likely be easier and safer for the board to remove it before playing on the side and risking slipping and scratching the pcb
EDIT: I found the specific volume key on asus-accessories.com for 12$!!
Thanks for your help! I already found and ordered the spare part on https://www.fixshop-online.de/ I hope that 24 Euros are not wasted.
Hopefully, the whole open and repair process will not be too difficult.
DerSteppo said:
found and ordered the spare part
Click to expand...
Click to collapse
I would be very interested in the results. Most importantly, if the spare part is a good quality replacement. Also I would be interested in how easy or hard such a replacement is. I looked into many of the teardown videos before buying the device, but those are usually from super-experienced pros with all the fancy tools. I would be interested in a first-hand report, even if it's short.
I will keep you updated. A friend sent some special adhesive tape but it hasn't arrived, so I didn't start disassembling.
The spare part, however, seems to be not available. I received an email that they don't have it. So I wait a little, maybe they can order it, but if it will not arrive end of April, I will just try to fix the bent old one.
@amenthes
I managed to open the phone with a hairdryer. I probably should have applied more heat, but I was hesitant because I did not want to destroy something, so it was a little bit harder to remove the back cover with a plectrum-like tool. Around the rim of the cover is a black adhesive tape, which I completely removed without any traces.
Unfortunately, I received another email that the spare part was not available, so I (not wanting to wait for a month or longer) cancelled the order eventually. Problem was, the volume button is somehow fixed to the case and I could not reach it properly. I managed to push it back a little bit, but could not remove it for replacement. During the process, I damaged the lower volume contact (as I wrote, the part is hard to reach) unfortunately. So now the volume down button does not work at all. However, the volume up button now does not get triggered automatically anymore. So I just push vol+ and lower the volume on the screen or via bluetooth headset. Works for me, as long as it doesn't go max. volume all of a sudden anymore.
A friend gave me some double sided adhesive tape which came with his replacement battery and I cut it with a razor blade to fit the back cover. It does not go all the way around, but I don't want to take the phone into water anyways. Besides, it looks just as it has never been opened. No gap at all, so the opening and closing parts are fairly easy.
All in all, it has been an experience. I will keep the phone despite the broken button, because for me it is still one of the best phones available at the moment.
Thank you for reporting back
@amenthes
Hi, it's been a while but I finally managed to replace the button!
I found a spare part on AliExpress. Not only was it much cheaper than on the other website, it is the whole middle frame instead of the button only. Delivery was expected end of June, however it arrived today (yeah!).
I used a razor blade and a thin needle as lever to remove the new button from the frame, since there seems to be no way from the inside without making things too complicated.
To remove the old button from the phone, which was bent and messed up (I tried to rip it off with a needle-nose pliers, but it did not work and it left some ugly marks), I used a sharp knife instead. I got inspired by this teardown video of another phone which unfortunately I don't remember. In the video, the guy used the knife like he would peel an orange. Like you would try to cut the button from the top edge. If enough pressure is applied you can pull the button out.
Eventually, I inserted the new button and pushed it a few times from different angles and now it feels almost as new. There is a nice click and pressure point. So I consider this a win.
At the end of the day, I did not even have to open the back of the phone with this method, but I learned a few things, which is nice, and, you know, you never know. Also, it gave me some confidence in my technical skills.
DerSteppo said:
@amenthes
I managed to open the phone with a hairdryer. I probably should have applied more heat, but I was hesitant because I did not want to destroy something, so it was a little bit harder to remove the back cover with a plectrum-like tool. Around the rim of the cover is a black adhesive tape, which I completely removed without any traces.
Unfortunately, I received another email that the spare part was not available, so I (not wanting to wait for a month or longer) cancelled the order eventually. Problem was, the volume button is somehow fixed to the case and I could not reach it properly. I managed to push it back a little bit, but could not remove it for replacement. During the process, I damaged the lower volume contact (as I wrote, the part is hard to reach) unfortunately. So now the volume down button does not work at all. However, the volume up button now does not get triggered automatically anymore. So I just push vol+ and lower the volume on the screen or via bluetooth headset. Works for me, as long as it doesn't go max. volume all of a sudden anymore.
A friend gave me some double sided adhesive tape which came with his replacement battery and I cut it with a razor blade to fit the back cover. It does not go all the way around, but I don't want to take the phone into water anyways. Besides, it looks just as it has never been opened. No gap at all, so the opening and closing parts are fairly easy.
All in all, it has been an experience. I will keep the phone despite the broken button, because for me it is still one of the best phones available at the moment.
Click to expand...
Click to collapse
Thanks for sharing your experience. Do you think the waterproofing was tempered by the repair ?
DerSteppo said:
@amenthes
Hi, it's been a while but I finally managed to replace the button!
I found a spare part on AliExpress. Not only was it much cheaper than on the other website, it is the whole middle frame instead of the button only. Delivery was expected end of June, however it arrived today (yeah!).
I used a razor blade and a thin needle as lever to remove the new button from the frame, since there seems to be no way from the inside without making things too complicated.
To remove the old button from the phone, which was bent and messed up (I tried to rip it off with a needle-nose pliers, but it did not work and it left some ugly marks), I used a sharp knife instead. I got inspired by this teardown video of another phone which unfortunately I don't remember. In the video, the guy used the knife like he would peel an orange. Like you would try to cut the button from the top edge. If enough pressure is applied you can pull the button out.
Eventually, I inserted the new button and pushed it a few times from different angles and now it feels almost as new. There is a nice click and pressure point. So I consider this a win.
At the end of the day, I did not even have to open the back of the phone with this method, but I learned a few things, which is nice, and, you know, you never know. Also, it gave me some confidence in my technical skills.
Click to expand...
Click to collapse
Thanks for sharing your experience. Do you think the waterproofing was tempered by the repair?
maxime78 said:
Thanks for sharing your experience. Do you think the waterproofing was tempered by the repair?
Click to expand...
Click to collapse
Probably yes, because I used adhesive tape and cut it myself along the back rim and it is not in one piece going all around. However, the cover sits very tight and you wouldn't even recognize that the phone was ever opened. I don't really mind because I use a silicon phone case anyway and I don't intend to take the phone underwater.
You can buy the original battery cover adhesive spare part here: https://www.asusparts.eu/en/asus-13040-01431000 but I did not want to spend more money and my solution works for me.
DerSteppo said:
@amenthes
Hi, it's been a while but I finally managed to replace the button!
I found a spare part on AliExpress. Not only was it much cheaper than on the other website, it is the whole middle frame instead of the button only. Delivery was expected end of June, however it arrived today (yeah!).
I used a razor blade and a thin needle as lever to remove the new button from the frame, since there seems to be no way from the inside without making things too complicated.
To remove the old button from the phone, which was bent and messed up (I tried to rip it off with a needle-nose pliers, but it did not work and it left some ugly marks), I used a sharp knife instead. I got inspired by this teardown video of another phone which unfortunately I don't remember. In the video, the guy used the knife like he would peel an orange. Like you would try to cut the button from the top edge. If enough pressure is applied you can pull the button out.
Eventually, I inserted the new button and pushed it a few times from different angles and now it feels almost as new. There is a nice click and pressure point. So I consider this a win.
At the end of the day, I did not even have to open the back of the phone with this method, but I learned a few things, which is nice, and, you know, you never know. Also, it gave me some confidence in my technical skills.
Click to expand...
Click to collapse
pulling out a device's button with a knife is like cutting ice cream with axe. You will always end up spoiling it.
Evan Roberts said:
pulling out a device's button with a knife is like cutting ice cream with axe. You will always end up spoiling it.
Click to expand...
Click to collapse
That's what I thought, but it worked surprisingly well actually!
@DerSteppo
Good day, sir. You have literally saved me from feeling extremely sad and even considering taking my phone to repair shop (which I never did in my life).
My story: I was snowboarding some days ago and at one point I fell on the slope on high(ish) speed. It was okay until I took a lift and took a look at my phone. It was almost exactly the same case as yours - the volume key was bent in the middle except it was vol. down which was stuck. Luckily the phone was still usable, I could adjust the volume via sound control panel in the settings which of course felt tedious but still not the end of the world until I get home and figure something out. Unfortunately while messing with the buttons now it was turn for vol. up to be pushed and there was no way to turn the phone on because it triggered the boot mode which wont let you out I came across that very video you mentioned and was baffled at why they made it so that you literally cant get the button from the frame without surely f**king something up in the process I started feeling anxious and thankfully google showed me this thread. All in all, I took your advice with a knife and managed to pry the buttons off a little and thankfully both buttons got released from their respective contact panels. So again, thank you so much man, don't think I could figure this out by myself
One question though. Not sure yet whether to get a new button instead of now scratched and still bent one, but was there any difficulty to insert the new button into the frame? There are two little 90 deg. angled metal things on each side and I am not sure if they can affect the insertion process.
Asus Zenfone 8 ZS590KS - Volume Button (Obsidian Black) - 13020-06381400 Genuine Service Pack | FixShop
Replacement volume button for Asus Zenfone 8 ZS590KS. Use the button if the original button has stopped working or is damaged and needs to be replace…
www.fixshop.eu
fluXion69 said:
@DerSteppo
Good day, sir. You have literally saved me from feeling extremely sad and even considering taking my phone to repair shop (which I never did in my life).
My story: I was snowboarding some days ago and at one point I fell on the slope on high(ish) speed. It was okay until I took a lift and took a look at my phone. It was almost exactly the same case as yours - the volume key was bent in the middle except it was vol. down which was stuck. Luckily the phone was still usable, I could adjust the volume via sound control panel in the settings which of course felt tedious but still not the end of the world until I get home and figure something out. Unfortunately while messing with the buttons now it was turn for vol. up to be pushed and there was no way to turn the phone on because it triggered the boot mode which wont let you out I came across that very video you mentioned and was baffled at why they made it so that you literally cant get the button from the frame without surely f**king something up in the process I started feeling anxious and thankfully google showed me this thread. All in all, I took your advice with a knife and managed to pry the buttons off a little and thankfully both buttons got released from their respective contact panels. So again, thank you so much man, don't think I could figure this out by myself
One question though. Not sure yet whether to get a new button instead of now scratched and still bent one, but was there any difficulty to insert the new button into the frame? There are two little 90 deg. angled metal things on each side and I am not sure if they can affect the insertion process.
Asus Zenfone 8 ZS590KS - Volume Button (Obsidian Black) - 13020-06381400 Genuine Service Pack | FixShop
Replacement volume button for Asus Zenfone 8 ZS590KS. Use the button if the original button has stopped working or is damaged and needs to be replace…
www.fixshop.eu
Click to expand...
Click to collapse
Hi, I am so happy to read I could help with my experience! Nice to see that you where able to fix it for now.
I did not have problems with inserting the new button, no. With the phone switched of, I just pushed it in and pressed a bit harder on both ends a few times. I think it "clicked" in at some point.
It is still working as new! One advice though: you might want to consider buying the original adhesive tape that is shaped to fit properly. I used just a few stripes and cut it to fit almost all the way around, but a few months ago I saw that the back cover was slightly lifted and there is a gap. The phone survived a few drops from various heights in the meantime, so I am not surprised. I am too lazy to re-apply new tape, though. It's in the rubber case anyways.
All the best!