*SOLVED*K-JAM Stuck on bootloder - 8125, K-JAM, P4300, MDA Vario Software Upgrading

Hi Guys;
I have a K-JAM (G3), I flashed it with (G4) rom by mistake; now it is stuck on bootloader screen with IPL 2.16 on the screen, After reading a number of threads I tried to flash original rom but some times it gives conection error and sometimes it continues untill it reach the progress bar on PC but the device screen still on RGB screen and after a while it gives connection error.
I can turn it off and when turned on it shows bootloader (RGB) immediatly. I tried hard reset but after I release the reset button it shows the RGB again

mm thats not good, this usually means you have bricked it, but sometimes recovery is possible.
Suggest you have a good look round this forum and do some reading : http://forum.xda-developers.com/forumdisplay.php?f=289 the wiki may have some info for you too.
If you have already tried to flash back a stock rom and it hasnt work, it aint good.
Not to rub too much salt in your wound, but if you had read the stickies on the above forum, you wouldnt have done it. But do read the stickies.
I will move this over to the wizard forum.

Problem Solved
First of all thanks timmymarsh for the reply.
I Kept searching and didnt give up, now my problem is solved thanks to the post by cochumbo
http://forum.xda-developers.com/showthread.php?t=321398
I followed the steps posted there and my K-JAM is flashed successfully and fully operational now

Kool, congrats and no probs

Related

BRICK - QMobile, Orange, hard spl'd ???

....before anyone moderates my ass i wasnt sure whch forum was the appropriate one for a bricking!
****
My phone seems to have given up the ghost. A few days after having put on the excellent Q-Mobile system. My phone has refused to boot properly. Heres what happens:
In start up from Soft reset, or Power off, i get the tricolour screen saying:
KAIS130 MFG
SPL-1.0 OliPof
CPLD-8
a few2 lines benath that is written 'Serial'
it then flashed onto a white screen saying 'loading......no image file' - this all takes about a second.
And then it rests on the screen mentioned above.
I haven't dropped it or done anything other than flash- correctly.
AAAARGH! it does randomly decide to boot up properly after its been left of for a whil if that helps.
Also - active synch wont recognise it , in the tr-colour state.
HELP!!!
Phone now stable
wondering what the best thing to do is to get it back on track...
i had same issue read the link to my post
http://forum.xda-developers.com/showthread.php?t=352859
mtty worked for me then i reflashed its worth a try i guess
kishorvalji said:
i had same issue read the link to my post
http://forum.xda-developers.com/showthread.php?t=352859
mtty worked for me then i reflashed its worth a try i guess
Click to expand...
Click to collapse
mtty is the way to do...you are not bricked...just take a few breaths and search the forums. When it happened to me, I had to use the BOOT command with MTTY. After it boots back up, run HARDSPL once again otherwise anytime you soft reset it will return to the bootloader screen.
thanks, but what is MTTY - i checked the posts and couldn't find it anywhere

Cannot Flash Original Rom

First off, anyone on this forum who has contributed anything, I am have the deepest respect for, and my favorites will get donations as soon as I have money. Ok enough a$$ kissing.
So here is my problem:
I flashed it's right's TNT 6.1 19919 after hardspling. After many problems, like pseudo-hard resetting (turning off, losing all but 6% battery, and changing the date back to what it was originally i.e. 1/27/06) while in a phone call and doing the same while using the wifi, i hard reset and still the same problems occurred. so I undid the hardspl, so now i am back to 2.25.001 in the bootloader but when i connect it to the computer (winxp) to flash the original rom (cingular 2.25) it freezes at 91%. If anyone has had this problem occur or knows the solution as to get ANY rom back on it, IT would be greatly appreciated.
Also after doing some reading I tried to flash wizard love 2.26 to it and that freezes at about 50-60%. so I am stuck and it is really annoying.
Full 8 hour charge, restart computer, different usb port. Same happens: Error 302 Update Error
Hum... maybe when you reCID locked it, you put a CID that's not for that official ROM you're trying to flash. The misbehavior of the phone is due to the ROM you had, not the CID Unlock. If I'm not mistaken, you can hardSPL it again, from bootloader. Then you can try and flash any other ROM you wish. Give my ROM (WM5SE rev5 - if your phone can handle 240MHz - or rev4) a go, after you have CID Unlocked your phone.
My phone can take up to 273 but, all the roms i flashed were g4 safe.... because the ipl spl never changed and i checked them in shell tool . it gives me a update error 302 which wizard love documentation says that the "phone needs a new rom code" which implies that it needs to be taken to cingular, and i dont think i can lie that well. how would one "accidentally" put their phone into bootloader?
theblackhandx said:
First off, anyone on this forum who has contributed anything, I am have the deepest respect for, and my favorites will get donations as soon as I have money. Ok enough a$$ kissing.
So here is my problem:
I flashed it's right's TNT 6.1 19919 after hardspling. After many problems, like pseudo-hard resetting (turning off, losing all but 6% battery, and changing the date back to what it was originally i.e. 1/27/06) while in a phone call and doing the same while using the wifi, i hard reset and still the same problems occurred. so I undid the hardspl, so now i am back to 2.25.001 in the bootloader but when i connect it to the computer (winxp) to flash the original rom (cingular 2.25) it freezes at 91%. If anyone has had this problem occur or knows the solution as to get ANY rom back on it, IT would be greatly appreciated.
Also after doing some reading I tried to flash wizard love 2.26 to it and that freezes at about 50-60%. so I am stuck and it is really annoying.
Full 8 hour charge, restart computer, different usb port. Same happens: Error 302 Update Error
Click to expand...
Click to collapse
You have posted present IPL/SPL 2.25.001,is it 2.25.001 or .0001 ?
As you removed 'HardSPL',did you reflash the appropriate IPL/SPL regarding your phones official bootloader IPL/SPL...?
You shud do the 'HardSPL' again and either do the removal of HardSPL again correctly as instructed in the sticky ' How to remove HardSPL' or Flash any other Rom to recover.
Cheers!
no it was 2.25.001 just a typo. i think i will try these suggestions when i get home and i will post my findings.

Rom Update problem, wizard stays rebooting

Hi,
I Tried to update my mda vario with a new rom. During the update my laptop, which I used to update the rom, crashed. The firmware update was at 96%.
When I rebooted my mda, I saw only a rgb screen. I searched the xda forum and saw that it wasn't a big problem. I only had to start the update proces again.
From that moment the real problems started. When I tried to update again, the phone rebooted several times during the update and the RUU gave several errors, every time another error code. I saw the error codes 300, 302, 264,274,262.
Every time I removed the battery and waited several minutes. At one point I had the battery removed for 8 hours. But every time I try to update the phone reboots during the update process (I see the percentage bar in the screen of the mda)
I tried several roms now, the roms i have tried are:
Wizard_Love_2.26.10.2_WWE_Novii_CF2
RUU_Prodigy_2210205_22102108_021911_TMO_NL_DUT_Ship.exe
MDA_Vario_1060202_103_11210_TMNL_Ship.exe
None of the roms succeedes to install.
Because, I am trying to update for 2 days now, I thought maybe my battery status is lower than 50%, so I wanted to load the battery to a 100%. When I connect my power adapter to the phone, the charging led will turn on, but the phone starts up (shows the RGB screen) and the charging leds turn off. So it seems I can't charge the battery either.
HELP!!!
Kind Regards,
Patrick
You didn't claim your IPL and SPL version, however it is almost confirmed that you didn't read the stickies here carefully. You need to CID-Unlock (G3) or HardSPL (G4) your device before flashing any ROMs!
For now, get your MDA Vario stock ROM and flash it, then you can get a working OS back. Then refer to the stickies.
starkwong said:
You didn't claim your IPL and SPL version, however it is almost confirmed that you didn't read the stickies here carefully. You need to CID-Unlock (G3) or HardSPL (G4) your device before flashing any ROMs!
For now, get your MDA Vario stock ROM and flash it, then you can get a working OS back. Then refer to the stickies.
Click to expand...
Click to collapse
And with your answer it is confirmed that you didn't read my post well.
But the problem is solved, i found a similar phone and could charge my battery, and I updated the phone with the stock version.

Error 262 Updating any Custom ROM

I am new to completely flashing a custom ROM. I've been trying to flash a new ROM on my tilt, with the latest AT&T updates(ROM 1.62.502.0 Radio 1.27.14.09). Each time I try to flash a custom ROM I get Error 262 Update Error. The progress bar never gets past 0%. I've tried multiple PCs and tried reinstalling ActiveSync. Am I missing something, or do I have to do something first before being able to flash the new ROM?
Any help is greatly appreciated!
Steve
i suggest u read all the wiki's and stickies regarding flashing a custom rom before taking any action...u obviously havent read it or havent got a good understanding of it which is why ur getting this error...and btw..i also suggest u search for solutions rather than just posting a thread like this which can be answered through a brief search of the forums.
I am about 100% sure you searched, didn't you?
Here, baby boy, let me spoon feed you and you can ask your mommy if she can whipe your drool:
http://www.digwin.com/view/schaps-wm6-pro-roms-update-error-262
bapssystupr3m3 said:
i suggest u read all the wiki's and stickies regarding flashing a custom rom before taking any action...u obviously havent read it or havent got a good understanding of it which is why ur getting this error...and btw..i also suggest u search for solutions rather than just posting a thread like this which can be answered through a brief search of the forums.
Click to expand...
Click to collapse
I have searched the forums over the past week or so. The solutions suggested such as soft reset, hard reset, reinstall activesync, switch USB ports, etc have not done anything. I also came across this thread:
http://forum.xda-developers.com/showthread.php?t=370205
which would suggest that I there is an incompatibility. I was hoping someone could point me in the direction of which radio version etc I would need to update to in order to update to a WM 6.1 ROM.
edit:yes I have run CID unlock.
Steve
AT&T 1.62.502.0 w/ 1.27.14.09 radio should flash fine on any Tilt even without CID unlock, since it's signed by AT&T. While I'm glad to hear your phone is CID unlocked, it's still strongly suggested that you flash HardSPL & Security Unlock your device.
Regarding your current issue, have you:
* Tried another computer to flash from?
* Entered tri-color bootloader mode on your phone prior to flashing? You can find out how to on the wiki.
Hope this helps!
_Alex_ said:
AT&T 1.62.502.0 w/ 1.27.14.09 radio should flash fine on any Tilt even without CID unlock, since it's signed by AT&T. While I'm glad to hear your phone is CID unlocked, it's still strongly suggested that you flash HardSPL & Security Unlock your device.
Regarding your current issue, have you:
* Tried another computer to flash from?
* Entered tri-color bootloader mode on your phone prior to flashing? You can find out how to on the wiki.
Hope this helps!
Click to expand...
Click to collapse
Thanks Alex! Tri-Color mode worked!
Steve
My error 262 fixed
I don't know if this is the best place to put this, but I didn't want to open a new thread.
I too had been getting repeated error 262. And I spent a couple of hours searching for answers, and while there have been many questions raised on this subject, there have been few clear solutions (and certainly none that worked for me).
I have the HTC branded Kaiser installing from Vista. (By the way I am new to this, but as I had such a hard time working this out, I thought I should at least post what worked for me.) I unlocked the CID with pof's Hard-spl v1 tool. Then (as I want to stay with Mobile 6.1) I upgraded the hard spl to v3.28 by JockyW. I then downloaded a number of Roms I wanted to try. That is where the trouble started.
Each ROM I tried would get past the tri-color screen with no problem. Then it would hang at the 0% until finally showing the error 262. A soft reset would reload my previous rom unchanged. I tried many things: removing all USB's, firewall, virus protection, hard reset, reboot windows, every suggestion I could find (and understand).
While the hard spl I had should have worked, I thought I should try version 3.29. When trying to upgrade to that I had a similar problem with error 260 this time. Looking over spl update instructions I realized I had forgotten to uncheck "disable usb connections" in "Activesync" at the proper stage. Once that was unchecked, the new spl loaded. After that I was able to load the cooked roms with no problem.
It appears there was something wrong with the HardSPL v3.28 I was using or in how I installed it. The tricolor screen was showing 3.28. In any case, after I reinstalled a new hard spl (this time 3.29), I had no more error 262.
A bit long-winded, but hopefully this might help someone else.

[SOLVED] Noob needs help! Is my qtek9100 a brick?

Hi!
this is my first post here, so sorry for my bad english or mistakes
i bought a qtek 9100 on ebay, and i'm wondering if it's a brick or not. i received the device 3 days ago. during this time i read through a LOT of threads here, tried a few things and nothing works.
here is some info:
- the phone is a qtek 9100 without branding
- the IPL is now 1.01 (i flashed "CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE" successfully)
- the SPL is 2.18 (because of the missing suffix ".0001" i guess it's a G3)
- GSM is 01.12.10
- OS is 1.5.4.2
- when i start the device (without any button pressed) it stops at the splash screen (which was a qtek logo before flashing, and is now this picture with a beer, that says "some things last forever" )
- i can get into bootloader screen (color screen) by holding camera button while starting
- in bootloader screen a small "USB" appears when i connect cable to usb on pc
- when i press communicate and voice buttons (on the sides) while starting, the "Press send to restore factory default" screen appears, but pressing send prints out "Format FAT Partition Format is Failed"
- the device gets recognized by windows ("Mobile Device" appears on my computer)
- ActiveSync 4.5 does not connect to device, not even as guest.
- when i hit "Connect..." in ActiveSync's connection settings, nothing is found
("Allow USB Connections" is ON)
- the device is CID-locked ("FF" state in Mtty 1.42)
- i can't unlock CID, because i can't get "EnableRapi.cab" onto the device without ActiveSync connection
Ok, these are basically the things i know now. The problem is that i never saw any other screen then the "HTC" boot screen, the "Qtek" splash logo (the one with the clouds) before i flashed with custom ruu wwe, after that i see the new splash logo, and i can get into bootloader (color) screen. I never saw any windows mobile running on this device! I could never establish a connection with ActiveSync!
So i hope that someone here on this nice forum can help me get this device to work (WM5 would even be enough right now) or at least give me a hint!
Thanks in advance!
Put the phone in bootloader mode and flash back to the original ROM.
since i bought it in ebay i don't have the original rom of this device.
but i found "233309-qtek9100_2180707_21807109_20710_qtek_ger_ship.exe" through google, which seems to be an original qtek rom (version 2.18). shall i flash this one?
You can find in the Wiki the latest official roms of every brand for our Wizards .-
ok, thanks.
i found one (Qtek GER 2.18.7) and flashed it. the process was successfull, now the IPL/SPL is both 2.18 . But the device still doesn't start and stops at the splash screen (which is now the original qtek splash again). I can still get into bootloader mode and hard reset results in "Format is failed"! No ActiveSync connection either... how should i proceed now?
i basically narrowed it down to these two problems:
- the splash screen freezes
- hard reset error "Format is failed"
( IPL: 2.18, SPL: 2.18 )
can't anybody help please?
i'm freaking out about this
With everything i’ve read the only people who’ve had any success had CID unlocked devices.
ok, i think that too for what i've read so far...
is there any other way of CID unlocking except lokiwiz (can't copy enablerapi.cab without activesync!)?
would this imei-check service that i've read about work in this case?
meanwhile i've also tried something with mtty (r2sd all) but doesn't work -> "didn't get proper security level"
is this also because of the CID lock? i tried to find out the right password to enter in mtty, but found nothing that worked...
does anybody know the correct password?
I couldent CID unluck my 9100 with lokiwiz so i did it 5min ago with Wizard Service Tool (ha to reboot my computer).
I'm having the exact same problem,
except I can't flash any other ROMS so I'm stuck looking at this incredibly frustrating beer picture, with "some things last forever".
Does anyone have any further ideas?
Look up the orignal rom on the wiki, get into bootloader. And flash it back.
Jodda said:
I'm having the exact same problem,
except I can't flash any other ROMS so I'm stuck looking at this incredibly frustrating beer picture, with "some things last forever".
Does anyone have any further ideas?
Click to expand...
Click to collapse
Jodda said:
I'm having the exact same problem,
except I can't flash any other ROMS so I'm stuck looking at this incredibly frustrating beer picture, with "some things last forever".
Does anyone have any further ideas?
Click to expand...
Click to collapse
Hi Friend!
I have the same problem with my Qtek9100!
Any ideas? have you solved your problem?
I have the frustrating beer picture
Please help me.
Very Thanks
Like I sad before
Get into bootloader, flash back the original rom and try again.
mizobuchi said:
Hi Friend!
I have the same problem with my Qtek9100!
Any ideas? have you solved your problem?
I have the frustrating beer picture
Please help me.
Very Thanks
Click to expand...
Click to collapse
I put the original rom.
But... the problem is the same.
when I started the device (without any button pressed) it stops at the splash screen (which has a qtek logo before flashing)
- i can get into bootloader screen (color screen) by holding camera button while starting, I installed the original and others rom who days before works perfectly... Now... this stopped at splash screen
- when I tryed to format.. = "Format FAT Partition Format is Failed"
Any idea?
I have tried this : http://forum.gsmhosting.com/vbb/showthread.php?t=332143
but... without success.
Could you help me, please?
Very Thanks
i'm still stuck with the same problem with hang up on qtek splash screen, too!
i have IPL 2.18 and SPL 2.18 and i can get in boot loader screen and connect with usb. (but no activesync connection!)
formatting doesn't work either.
does anybody have an idea how to solve this?? it's frustrating... i've tried almost every guide here on the forums.
same proplem here with
ipl 2.16
and spl 2.16
I used this to fix this problem
Hi i had the same problem the other week, installed a dodgy app, went to do a hard reset and wouldn't do a hard reset format failed. Tried updating rom everything worked ok until you booted it up. Wouldn't go past second splash sreen. After a few hours of trawling round i found this thread.
http://forum.xda-developers.com/showthread.php?t=276963&highlight=format+is+failed
worked for me. Hope this helps you out.
Problem in connecting to my PC
Hey ,
I just bought a qtek 9100 a day before ... I tried to connect it with my computer.. instead of connecting my battery gets charging well can u plz help me out !
is there any software that i should install in my pc in order to get it connected to my PC...... please help me fast ! Lot of work is pending !
Thanks
Salman
Ok guys, I finally have this SOLVED.
My QTEK 9100 is working fine now!!!
I'm so happy with it right now
Since nothing I tried worked, I went to imei-check.co.uk and got my phone completly unlocked! It only cost me about 11€ and since it works now I have to admit that it was worth it (no advertising). After the unlocking was done I could do the "r2sd all"-method (Tool: MTTY 1.42) using a miniSD card. You can find a good tutorial on this board somewhere. After that everything was just fine...
-> I never saw it working and Hell Yeah: This baby just kicks a$$ !!! (although it's kinda 'oldschool' these days )

Categories

Resources