Related
I was mistakenly copy the wrong rom into the SD card and run the cheetah unlocker - it starts to flash the rom. After that the TREO750 is dead and soft & hard reset will not help.
I can only go into the bootloader with 3 color screen. Pressing PTT and reset button.
Anything i can do to make this TREO750 work again ?
ojtan said:
I was mistakenly copy the wrong rom into the SD card and run the cheetah unlocker - it starts to flash the rom. After that the TREO750 is dead and soft & hard reset will not help.
I can only go into the bootloader with 3 color screen. Pressing PTT and reset button.
Anything i can do to make this TREO750 work again ?
Click to expand...
Click to collapse
If you can access the tri-color bootloader screen, then your Treo 750 is NOT dead.
The ROM is bad or wiped but the bootloader is good...that is sufficient for you to flash a good ROM & get it up & running.
What do you see on the bootloader screen?
Which ROM did you copy into the mini-SD card?
You could copy the .nbh file from the original WM6 ROM Upgrade package & change it to CHEEIMG.nbh into a freshly formatted (FAT32) mini-SD card & flash using the mini-SD card method.
thanks konker. I finally figure out the way to flash it with original ROM.
ojtan said:
thanks konker. I finally figure out the way to flash it with original ROM.
Click to expand...
Click to collapse
Great! I'm glad you got your phone working again.
glad to know its working again
Hi everyone,
I have a big problem and I need urgent help please. I have ATT 750 unlocked and I'm outside the States now. My Treo was 6.0 then I upgrade it to 6.1 so far so good.
Then I saw a custom rom that I thought it was interesting. the custom rom was for HTC Dimond I think. without paying too much attention. I started the upgrade. It went 70% before the upgrade crashed.
Now my Treo is not responding to anything. I have the original ATT 6.0 SD upgrade and I have the 6.1 lite upgrade. I'm using CheetahUnlocker to flash the SPL (that is working) but when I try to install the 6.0 or 6.1 using Kaiser Custom RUU v1 it crash.
I saw the post above that suggest to place the original 6.0 on a freshly formated SD and install from there. that is not working either. when I try to install the software it goes into these steps before it crashes: btw, I have the tri-color bar and it has the following info:
CHEE100
IPL-0.20
SPL-1.40.01iNex
while update in progress i see the following:
CHEEIMG.nbh
SPLASH1 - OK
BOOTLOADER - OK
GSM - OK
MicroP - OK
EXTROM - Fail
OS -
After the crash I get this msg: "Update Terminate Update Failed"
Any suggestion please? need more info? then let me know
Thanks in advance
Sam
Any answer
Hello Sam,
I actually had the same problem, did you get it fixed?
Please let me know, how?
Thanks a lot
Same problem here
In the 3 colored screen just displays this.
Palm Tr
IPL-0.20
Palm Tr
SPL-0.21.0000
When i insert the freshly Fat32 formatted SD card with the rom , apears "loading" for about 2 seconds and then just ends with the tricolored display.
Thanks for any advice.
Apoapo said:
Same problem here
In the 3 colored screen just displays this.
Palm Tr
IPL-0.20
Palm Tr
SPL-0.21.0000
When i insert the freshly Fat32 formatted SD card with the rom , apears "loading" for about 2 seconds and then just ends with the tricolored display.
Thanks for any advice.
Click to expand...
Click to collapse
You need to run Hard SPL first before flashing any ROM.
Your display would look like safisam's if you had run Hard SPL. (SPL-1.40.01iNex)
safisam said:
Hi everyone,
I have a big problem and I need urgent help please. I have ATT 750 unlocked and I'm outside the States now. My Treo was 6.0 then I upgrade it to 6.1 so far so good.
Then I saw a custom rom that I thought it was interesting. the custom rom was for HTC Dimond I think. without paying too much attention. I started the upgrade. It went 70% before the upgrade crashed.
Now my Treo is not responding to anything. I have the original ATT 6.0 SD upgrade and I have the 6.1 lite upgrade. I'm using CheetahUnlocker to flash the SPL (that is working) but when I try to install the 6.0 or 6.1 using Kaiser Custom RUU v1 it crash.
I saw the post above that suggest to place the original 6.0 on a freshly formated SD and install from there. that is not working either. when I try to install the software it goes into these steps before it crashes: btw, I have the tri-color bar and it has the following info:
CHEE100
IPL-0.20
SPL-1.40.01iNex
while update in progress i see the following:
CHEEIMG.nbh
SPLASH1 - OK
BOOTLOADER - OK
GSM - OK
MicroP - OK
EXTROM - Fail
OS -
After the crash I get this msg: "Update Terminate Update Failed"
Any suggestion please? need more info? then let me know
Thanks in advance
Sam
Click to expand...
Click to collapse
Have you tried re-downloading the ROM in case you have a bad file? Also, have you tried a different SD card, or re-formatting the SD card you are using? Sometimes that will help, and make sure the CHEIMG file is the only file on the SD card.
startngate said:
You need to run Hard SPL first before flashing any ROM.
Your display would look like safisam's if you had run Hard SPL. (SPL-1.40.01iNex)
Click to expand...
Click to collapse
Thanks man, i was looking for any way to HARD SPL directly from the older loader, i couldn't find any.
But i already solved loading in the SD card an "original" ROM from palm.
Now i got this treo working again
Hi all
I have the same problem, after some progress during the update it stops and now I can see just the Palm logo inicialyzing...
I stil can get the Bootloader Screen (3 collors), but when I try to pass other ROM It says "file image corrupted"...
I´ve been trying with 4 SD card that I have (512Mbs up to 2Giga), but nothing works...
It seems that the Treo doesn´t recognize the SD card!!!!
How could I Pass a ROM not using the SD card??
Any help??
Palm treo 750 storage memory problem after flashing!Please help
Please help me!!!!!!!I have occurred this problem in my Palm treo 750 after flashing:i get this
message error:"Storage memory is critically low.i the storage momory is not increased. other
programs may not be able to star.Use file explorer to delete files that are no longer needed or
move some files to strage card".
And when i look the memory storge i see only:
-4.82 MB(Tatal memory storage)
-2.3MB in use and
1.78MB free
And like you know the real total memory storage is: 60MB.
Please help me!!!!!!It happen after i update it to Wm6.1
And hard reset, soft reset don't help.Help please!!!!!!!!
darabah said:
Please help me!!!!!!!I have occurred this problem in my Palm treo 750 after flashing:i get this
message error:"Storage memory is critically low.i the storage momory is not increased. other
programs may not be able to star.Use file explorer to delete files that are no longer needed or
move some files to strage card".
And when i look the memory storge i see only:
-4.82 MB(Tatal memory storage)
-2.3MB in use and
1.78MB free
And like you know the real total memory storage is: 60MB.
Please help me!!!!!!It happen after i update it to Wm6.1
And hard reset, soft reset don't help.Help please!!!!!!!!
Click to expand...
Click to collapse
First of all, please indicate which ROM you loaded on your device.
Secondly, it would help the community to help you if you could state what software modifications you've performed on the phone. eg. HardSPL etc
Lastly, a list of installed software on your phone would be useful too.
Palm treo 750 storage memory problem after flashing!Please help
I had windows mobile6 Treo 750 2.27 ce os 5.2.1239(build 17746.0.2.4) original and i update to 6.1 Treo750_OS5_2_19199WWE_STD.rar. i used CheetahUnlocker, MAGIC_UNLOCKER and Treo750v_ExtROM_Unlockers with SD method
Like it descripted to the forum.
Plaese help me! Thank you for your reply!!!!!
darabah said:
I had windows mobile6 Treo 750 2.27 ce os 5.2.1239(build 17746.0.2.4) original and i update to 6.1 Treo750_OS5_2_19199WWE_STD.rar. i used CheetahUnlocker, MAGIC_UNLOCKER and Treo750v_ExtROM_Unlockers with SD method
Like it descripted to the forum.
Plaese help me! Thank you for your reply!!!!!
Click to expand...
Click to collapse
From your description, it seems both of them are original stock ROM. Is your Treo a telco branded model or a unbranded unlocked model?
If the latter, you did not have to run the other utilities to unlock the phone...just flash the ROM.
I see that you ran the ExtROM unlocker...why did you have to do that?
The ExtROM is used to store device specific ROM customization that you should not have to bother too much if your ROM is a unbranded ROM (ie. not AT&T ROM etc).
If you left the ExtROM in it's unhidden state, that could be why the system is reporting the amount of free space to be so low. You should hide the ExtROM & then hard-reset the device again to see if that solves the problem.
Palm treo 750 storage memory problem after flashing!Please help
Thank u for your reply!
My Treo is unlocked model but i don't know if it is unbranded and it is from Palm Rom not AT&T ROM.
I'm news, can u tell me how to hide the ExtROM(Can u explain how to proced please?).
Thant u for all!!!!!
Need a favours over here. Recently, i bricked my trinity. P3600 more precisely Dopod D810 (i flashed wrong ROM -> Unpacking cooked rom for trinity but i merge it with -Hermes cmd in NBMerge! houh... so stupid! ). Soo... just not what i expected, Rom flashing stop on half, SR my trin and tada.... 3Color screen bootloader popup! haaarggg, i try flashing another rom using any rom that has same CID *official or cooked rom* (some are 100% thru, but someother not) but like usual it won't start the windows (just blank/black screen with green led[ always on!) Never been like this before! Have been flashing several times using any cooked rom by great chef on trinity but this time! :doh: damn it! my bad.
i found solution on the forum *Unbricking Trinity Stuck on Bootloader* but since my usb port can't be detected on my vista/xp machine, whether i disable AS and changed my usb cable it doesnt work at all, on mtty too! so i can't use that utility. i try run install sspl olipro 1.3 but it never changed my spl at all. now i can't use my trin at all cuz allready dead.
btw this is the info on trin 3color screen bootloader:
IPL 1.00
SPL 3.20 OLIPRO
anysolution for bringing back my trinity from the death? maybe a tools/utility to unbrick trinity from SD or something like that, which not involved any pc connection, without bring this devices to htc center of course.
I hope any expertise on this forum would helped me sort out this probs.
Sorry for my english and thanks for reading my post.
Read this :http://forum.xda-developers.com/showthread.php?t=308691 download splxploit-windows.zip (935.1 KB, 7619 views) put phone in bootloader run splxploit when bootloader change
After this download full rom here is link:http://rapidshare.com/files/21174752/RUU_Trinity_HTC_WWE_1.15.405.5_6275_1.20.00.11_12201_Ship.exe
Then flash full rom bat do not disconnect usb cable in any step.
Before use any step disable active sync.
Usb are dead
Gsmhacks thanks for ure reply. I have tried that one, and lot read ing on wiki. But since i cant use the usb i cant use that splexploit whether on live linuxcd, or .Net version even win version. The usb port cant be opened . I think i broke the usb pin. From the beginning everytime i flashed my trin i never used ruu utility, i always do the sd card method and that is the best and easiest method and it works for me.
I just curious perhaps can anyone or is there any utility to unbrick trin via sd card. I knew a lot a people has bring their trinity life from dead by using htc stackflow splexploit. I hope that was work for me too! Too bad my usb are dead. Damn!
Here what you need bat only work if you have hard spl
If you install hard spl before brick trinity you can use SD CARD to flash trinity. YOu need to formate sd card to FAT32 with Card Reader donwload full rom here is link: http://rapidshare.com/files/21174752/RUU_Trinity_HTC_WWE_1.15.405.5_6275_1.20.00.11_12201_Ship.exe
then extract and file RUU_Signed.nbh rename to TRINIMG.nbh and copy it to the root folder of your miniSD card.
Here is full instruction again also first format sd card to FAT32 !!!! VERY IMORTANT to format sd card to FAT32 or all other step will not work THEN:
1. Extract the .NBH file from your prefered ROM upgrade: In windows use winrar (right click) to extract the contents of the exe file. In Linux / MacOS use cabextract (or you can also use winrar via wine).
2. Rename the .NBH file to TRINIMG.nbh and copy it to the root folder of your miniSD card.
3. With miniSD card inserted on the phone, start the bootloader (hold Power button on right side and Camera button at same time and stick with stylus in RESET on bottom).
4. You should see the screen pictured on the left, confirm flashing on screen by pressing the power button.
5. Flashing might hang after some time but this is normal. Just wait. Complete flash takes about 30 minutes, so check your battery or connect to charger before the flashing process starts.
6. When flashing completes soft-reset your device.
and you will flash and unbrick trinity bat this only work if you install before this hard spl i mean cid unlock trinity. if not you must fix usb port.
That will work? I hope so
Ok then i'll try flashing using that rom. Oo, i have install hardspl btw and so far flashing using sdcard method no probs. But after i bricked my trin flashing doesnt smooth like be4. Always gave me error 0018003 update fail on the halfway, i guess because i have bad nand on trin and probably cuz cooked rom.
Can u give me another link, perhaps on xda ftp. rapids so slow 4 me. Btw i have download dopodasiawwe official rom on xda ftp *twice but still when i tried to run the package it gave me corrupt archive integrity fail w!f.
Thanks gsmhackerns, i downloading the package now!
Perhaps you can find a way to make a goldcard for Trinity?
See http://forum.xda-developers.com/showthread.php?t=437996
That's what i looking for! Thanks.
Humm, superb. Yay, great! Thank you stepw. Even its for elf with a little mod i hope this will work. Once again thank you.
Stepw, i have tried making the gold card, everything went ok. I have temp. cid *supercid* but the probs now is i can't download http://rapidshare.com/files/21174752/RUU_Trinity_HTC_WWE_1.15.405.5_6275_1.20.00.11_12201_Ship.execan someone uploaded to somewhere else. Rapidshare crap! perhaps on xda ftp.
thanks!
goldcard cannot help in such a situation.
I can however make an SSPL that loads off SD card - just like for kaiser you will be able to use it because you are already on hardspl.
then that will allow you to flash stock SPL.
PM me and send your MSN address, so we can test it out. if it works i'll post it in this thread too in case others get stuck also
cmonex said:
goldcard cannot help in such a situation.
I can however make an SSPL that loads off SD card - just like for kaiser you will be able to use it because you are already on hardspl.
then that will allow you to flash stock SPL.
PM me and send your MSN address, so we can test it out. if it works i'll post it in this thread too in case others get stuck also
Click to expand...
Click to collapse
Indeed. Youre right cmonex, it doesnt make any difference at all 4 my trin. After several tried using and making goldcard 4 trin, finally i made working goldcard4trin, but gosh it still stuck when i tried to update the os (update os fail) humm anyone.
Sorry for wasting your time with Goldcard, I have overlooked that you have a hard spl on your Trinity. In this case goldcard doesn't make a lot of difference.
And there's no trindiag.nb to the best of my knowledge that could be used instead of SSPL cmonex is suggesting to run from SD.
Back to the topic, sounds like you have some "bad" blocks in flash and OS can't be flashed. Bad blocks can be reset with "task 2a" command, see this thread for more details:
http://forum.xda-developers.com/showthread.php?t=330496
The question is how to run it without USB and I don't have an answer for you
Some people have previously mentioned they managed to flash smaller OS images when larger images failed, perhaps if you try flashing some minimal vanilla ROM, it will succeed?
Bad NAND, Yup!
Ya... as i mention before yup i do have bad nand block on my devices. Using manila rom with smaller img size the flash went 'OK'. But it doesn't boot at all infact just black screen with green led on.
Okay the only solution probably use mtty and do task 2a if i'm not mistaken. But like you said "The problem is the USB port". I think the port is ok cuz i already tested it connecting my usb to my trin without inserting the battery and the red led *magenta* is on. humm, weird!
But if something can make it working without involving any pc connection it would be a great achievement. hahah! well i supposed i have to put my trin on bunker before someone can make it happens
I asked SEA in my country and they recommend me to changed the machine it self and they charge me around US $160 ho...ho.. too "wideeeeee" for college boy like me
Same problem, i flashed the rom
RUU_Trinity_DOPODASIA_WWE_3.00.707.18_6275_1.46.30.11_108_Ship
and after that i tried to flash a new radio!
power+cam and the cell phone did not show usb, then i used sspl to rum the radio but it locked at 0%
after that it is stucked at bootloader screen
ipl 1.0
spl 3.20 .....
but no usb and no sd card !!
did i lost the cell phone?
there is no jtag ou something like that ?
so now... you still want this SSPL? i'm thinking of patching one up to automatically run task 2a maybe. or just restore stock spl for warranty service if that's what you have in mind. but you didn't really reply to that offer?
Please if you could build a sspl for this condition it would be enough because once sspl i can run a new ruu with hard-spl again ! the problem i believe was caused becaus this original rom's have a spl.nb inside , in the screen we read teh information about the olipro spl but i thing teh original spl.nb messed up the hard spl!
There is another problem, i formated to fat32 my card and put a TRINIMG.nbh of a rom inside and he did nothing!! same card in elf with ELFIMG.nbh of a rom runs great!!
It means that this spl of mine will not flash from card? goldcar would help?
and cant i flash something in serial ? like a jtag or something?
Anyhelp will be more than apreciated!
sorry the bad english
Needed!
Cmonex, sorry for longtime haven't seeing this thread again. okay i really need your help btw if you willing to help me. The spl your talking about perhaps can sort out the probs (i hope) at least we tried. as for task2a cmd to clear the bad nand block is none usefull for me since usb conn. are definitely drop dead.
how about patch the SSPL to do task2a cmd to solve the bad NAND block first.
dinizbruno said:
Please if you could build a sspl for this condition it would be enough because once sspl i can run a new ruu with hard-spl again ! the problem i believe was caused becaus this original rom's have a spl.nb inside , in the screen we read teh information about the olipro spl but i thing teh original spl.nb messed up the hard spl!
There is another problem, i formated to fat32 my card and put a TRINIMG.nbh of a rom inside and he did nothing!! same card in elf with ELFIMG.nbh of a rom runs great!!
It means that this spl of mine will not flash from card? goldcar would help?
and cant i flash something in serial ? like a jtag or something?
Anyhelp will be more than apreciated!
sorry the bad english
Click to expand...
Click to collapse
no usb, no sd, no chance sorry. jtag it or get it serviced or get another phone.
as for jtag, hermes jtag has been worked out by scholbert. trinity is probably the same, but you will have to find the pins. the rest of the process will be the same.
Dear all,
I can't go to bootloader screen ..fff before I had on my trinity faman 4.03 rom and I would change with the NiAX rom... after 3% restart and I think that my phone brick and my phone stay on htc screen fff please help
I have windows vista and even if i follow all steps pfff it changes nothing...after hard reset ...fff please help ...
I think my trinity is out :-(????????????????????????
Please help,
The O.S is more important to these operations than can be stressed - for a 99% safe flash Win XP is your best bet , I have had nothing but error 260,270 halfway flashed roms and usb faults running on vista and since I had my original bricking episode - NOTHING , I repeat NOTHING including genuine roms has flashed without a recovery or at least without doing something strange in the process - SPLXPLOIT has been a saviour here , without it I would've been lost.
Cant the O.P simply use another machine to test out the USB theory ?
ALIVE AGAINnnnnnnnnnnnn!!!!!!!!
My p3600 was stucked att bootloader, and wont give "usb" and do not read TINIMG.NBH (tried on elf with ELFIMG.nbh and the card was great)!
I did a golcard with the post on elf about it and the cell with the gold card inside was the same, no trinimg.nbh and no usb.............
BUT..............
with the goldcard inside, turned OFF, i placed it on the usb cable off the pc and the device booted to the bootloader screen, but this time he got "USB" , before flashing anything i removed the card , and putted switched off in the usb, booted with "serial" with card and pressing power and then placing usb still "serial" message!
I putted the card, did not switched on , placed on the usb and waited for it to boot for it self , and for my surprise "usb".
Flashed stock rom, and it booted nice!!!
Please try!
saved my day!
sidekraouf95 said:
Dear all,
I can't go to bootloader screen ..fff before I had on my trinity faman 4.03 rom and I would change with the NiAX rom... after 3% restart and I think that my phone brick and my phone stay on htc screen fff please help
I have windows vista and even if i follow all steps pfff it changes nothing...after hard reset ...fff please help ...
I think my trinity is out :-(????????????????????????
Please help,
Click to expand...
Click to collapse
I have to know how to repair my phone please... nobody can explain precisely how to put my phone on bootloader using my sd card directly from my computer under vista...???
ok, some urgent help needed, yesterday ok, today will not start. only get as far as, 'smart mobility' R1.27.12.32 G22.45.88.07H D 1.56.00.00
phone is standard WM6 HTC. i have the 6.1 image for upgrading and tried to load using SD card, i get past tri colour screen, then loading, then checking then 'not allowed' and back to tri colour. it says KAIS130, SPL-1.93.000 CPLD-8. what?next
any help appreciated guys......
gazzacbr said:
ok, some urgent help needed, yesterday ok, today will not start. only get as far as, 'smart mobility' R1.27.12.32 G22.45.88.07H D 1.56.00.00
phone is standard WM6 HTC. i have the 6.1 image for upgrading and tried to load using SD card, i get past tri colour screen, then loading, then checking then 'not allowed' and back to tri colour. it says KAIS130, SPL-1.93.000 CPLD-8. what?next
any help appreciated guys......
Click to expand...
Click to collapse
To Flash a ROM you'll most likley need Hard SPL
Follow the "Getting Started" Link in my Sig.
If you cannot get WM to boot, you'll need to re-flash your orginal carriers ROM.
Ta
Dave
thanks for quick reply DaveShaw. fell at the first though, site for 'Cmonex's HardSPL 3.29SD' is blocked here in UAE, dont know why. are there any other links?
gazzacbr said:
thanks for quick reply DaveShaw. fell at the first though, site for 'Cmonex's HardSPL 3.29SD' is blocked here in UAE, dont know why. are there any other links?
Click to expand...
Click to collapse
You shouldn't be using cmonex's SD method the first time round. It is for upgrading only.
I have downloaded the package from point 2 (you should follow the USB method in post 3, NOT the SD set) and have upload it onto my site, please let me know when you are done with it.
http://taeguk.co.uk/xda/HardSPL and CidUnlocker.zip
Ta
Dave
ok, thanks DaveShaw, i have downloaded those files. the method in step 2 involves copying the jump progs to the device memory, which i do not have access to as it will not start. can i just copy to the sd card? thats why i was trying to flash a standard rom. i need a solution that will work just from the card. will the RUU_Kaiser_HTC_WWE_1.56.405.5_radio_sign_22.45.88.07_1.27.12.11_Ship.rar load using what i have on my phone now? i assume that the spl gets replaced when i upgrade to 6.1 with htc ruu. i can try anything as i have nothing to lose now (do i?)
gazzacbr said:
ok, thanks DaveShaw, i have downloaded those files. the method in step 2 involves copying the jump progs to the device memory, which i do not have access to as it will not start. can i just copy to the sd card? thats why i was trying to flash a standard rom. i need a solution that will work just from the card. will the RUU_Kaiser_HTC_WWE_1.56.405.5_radio_sign_22.45.88.07_1.27.12.11_Ship.rar load using what i have on my phone now? i assume that the spl gets replaced when i upgrade to 6.1 with htc ruu. i can try anything as i have nothing to lose now (do i?)
Click to expand...
Click to collapse
Enter your bootloader and try flashing any ROM supplied by your carrier to get into Windows Mobile.
What screen do you get stuck on? If it is the tri color screen check out the link in my signature.
Ta
Dave
Hi again, i am not actually 'stuck' on the screen as i can get into the loader, its just that i get the message saying that the (newer) rom will not load. i am extending my (c)rapidshare as free will not let me down load the 'standard' rom, then i will try that (just had to re-initialise my paypal and the passwords are on eWallet the phone, so ive reloaded the eWallet on my pc and ....so it goes on zzzzzzzzzz its funny how these things spiral down - not).
is there any way to update the spl only from the sd card?
gazzacbr said:
Hi again, i am not actually 'stuck' on the screen as i can get into the loader, its just that i get the message saying that the (newer) rom will not load. i am extending my (c)rapidshare as free will not let me down load the 'standard' rom, then i will try that (just had to re-initialise my paypal and the passwords are on eWallet the phone, so ive reloaded the eWallet on my pc and ....so it goes on zzzzzzzzzz its funny how these things spiral down - not).
is there any way to update the spl only from the sd card?
Click to expand...
Click to collapse
No.
Can your phone boot into Windows or not?
Ta
Dave
Hi, no, it will not boot to windows. just been reading around while 'RUU_Kaiser_HTC_WWE_1.56.405.5_radio_sign_22.45.88.07_1.27.12.11_Ship' is downloading. ive got connected with mtty and get cmd>. when i type boot i get 'Command Error !!!' i assume thats not good, i think rom is corrupted. tried standard HTC 6.1 RUU_Kaiser_HTC_FIN_3.29.414.0_radio_sign_25.83.40.02_1.65.17.56_Ship version 3.14.4.1 again on USB and after phone says 1% also message saying that it will not load error 294: invalid vendor id
gazzacbr said:
Hi, no, it will not boot to windows. just been reading around while 'RUU_Kaiser_HTC_WWE_1.56.405.5_radio_sign_22.45.88.07_1.27.12.11_Ship' is downloading. ive got connected with mtty and get cmd>. when i type boot i get 'Command Error !!!' i assume thats not good, i think rom is corrupted. tried standard HTC 6.1 RUU_Kaiser_HTC_FIN_3.29.414.0_radio_sign_25.83.40.02_1.65.17.56_Ship version 3.14.4.1 again on USB and after phone says 1% also message saying that it will not load error 294: invalid vendor id
Click to expand...
Click to collapse
Yeah, you need the ROM your carrier supplied.
Where is the Phone from?
Does a Hard Reset help?
Ta
Dave
woo hoo, yippeeeeeeeeeeeeee. the kaiser lives. back to standard 6.0 rom. cheers, i owe you a beer (or 2) if you are ever in abu dhabi, let me know ;-)
i can reload all from sprite backup (only from yesterday) to get me going again
but..... next will try to replace spl and then load 6.1. not sure why HTC standard would not let me update, i thought the ruu would update any htc phone
HardSPL 3.29 is first (yes?) then will try Kaiser_HTC_ASIA_HK_WWE_3.34.721.2 which sounds good. one more thing, my phone is not locked so do i need to do the 'SIM and CID-Unlock'
gazzacbr said:
woo hoo, yippeeeeeeeeeeeeee. the kaiser lives. back to standard 6.0 rom. cheers, i owe you a beer (or 2) if you are ever in abu dhabi, let me know ;-)
i can reload all from sprite backup (only from yesterday) to get me going again
but..... next will try to replace spl and then load 6.1. not sure why HTC standard would not let me update, i thought the ruu would update any htc phone
HardSPL 3.29 is first (yes?) then will try Kaiser_HTC_ASIA_HK_WWE_3.34.721.2 which sounds good. one more thing, my phone is not locked so do i need to do the 'SIM and CID-Unlock'
Click to expand...
Click to collapse
That's right, flash the HardSPL 3.29 first (SIM unlock is optional, CID unlock isn't needed - Hard SPL takes care of that - but it comes as part of the SIM unlock) then flash a WM6.1 ROM.
Ta
Dave
gazzacbr said:
not sure why HTC standard would not let me update, i thought the ruu would update any htc phone
Click to expand...
Click to collapse
Only if it's from the same region the RUU was intended for eg the European TyTN II's won't accept the latest Hong Kong WWE ROM by default because of this so as already suggested hardSPL works around this. My WM 6.0 UK original TyTN II upgraded to WM 6.1 OK but that was using the HTC UK provided ROM update. That updated everything required including the SPL and Radio to the required HTC versions. I'm back on the original WM 6.0 version though due to reliability issues with 6.1 and poor GPS performance.
hello guys, as i have posted in other threads but no one gave me any soultion to my problem so im starting this thread.
ok i have xperia purchased from UK.
im trying hard to use jack's rom 1.07.
i have done hard spl..i started X1_HardSPL, some message showed on xperia i click yes, it restarted my device. and X1_HardSPL gave me error that it cant connect to my phone...i put my device in bootloader mode and it was showing this on colour screen:
KOVS110
SPL-0.72.0000
MicroP1-787
MicroP2-787
then i used the sd card way..i put the jack's rom file in the card after formatting it with fat32 format..i put the device in bootloader and after the colour screen it shows LOADING and i waited for an hour but nothing happen..
2nd way i used was i ran hardspl file again in a folder, it created some temporary files, i renamed the jack's rom to RUU_Signed.nbh and overwrite the file in hardspl folder.....it again restarted my device to bootloader and after coloured screen it showed LOADING and thats it..nothing else..and hardspl file running on pc gave me 260 or 262 error i cant remember..
so anyone kindly tell me what im doing wrong?and how to fix this
thanx
najaf363 said:
hello guys, as i have posted in other threads but no one gave me any soultion to my problem so im starting this thread.
ok i have xperia purchased from UK.
im trying hard to use jack's rom 1.07.
i have done hard spl..i started X1_HardSPL, some message showed on xperia i click yes, it restarted my device. and X1_HardSPL gave me error that it cant connect to my phone...i put my device in bootloader mode and it was showing this on colour screen:
KOVS110
SPL-0.72.0000
MicroP1-787
MicroP2-787
then i used the sd card way..i put the jack's rom file in the card after formatting it with fat32 format..i put the device in bootloader and after the colour screen it shows LOADING and i waited for an hour but nothing happen..
2nd way i used was i ran hardspl file again in a folder, it created some temporary files, i renamed the jack's rom to RUU_Signed.nbh and overwrite the file in hardspl folder.....it again restarted my device to bootloader and after coloured screen it showed LOADING and thats it..nothing else..and hardspl file running on pc gave me 260 or 262 error i cant remember..
so anyone kindly tell me what im doing wrong?and how to fix this
thanx
Click to expand...
Click to collapse
did you do this (prefereble on an XP machine)
Phone Synced with PC
run X1_HardSPL.exe
follow on screen instruction, including after getting the drivers installed on you xp or vista machine installed, so the hardSPL will make the phone in bootloader and make sure it says 100% done on you xperia. and XP VISTA
then put inte bootloader holding down volyme button and power until tricolor screen is shown, and make sure that the imgage.nbh file is named correctly.
'
then it should work.
the most common failure is that the hardspl isnt installed correctly.
najaf363 said:
hello guys, as i have posted in other threads but no one gave me any soultion to my problem so im starting this thread.
ok i have xperia purchased from UK.
im trying hard to use jack's rom 1.07.
i have done hard spl..i started X1_HardSPL, some message showed on xperia i click yes, it restarted my device. and X1_HardSPL gave me error that it cant connect to my phone...i put my device in bootloader mode and it was showing this on colour screen:
KOVS110
SPL-0.72.0000
MicroP1-787
MicroP2-787
then i used the sd card way..i put the jack's rom file in the card after formatting it with fat32 format..i put the device in bootloader and after the colour screen it shows LOADING and i waited for an hour but nothing happen..
2nd way i used was i ran hardspl file again in a folder, it created some temporary files, i renamed the jack's rom to RUU_Signed.nbh and overwrite the file in hardspl folder.....it again restarted my device to bootloader and after coloured screen it showed LOADING and thats it..nothing else..and hardspl file running on pc gave me 260 or 262 error i cant remember..
so anyone kindly tell me what im doing wrong?and how to fix this
thanx
Click to expand...
Click to collapse
DO NOT I REPEAT
DO NOT
use the hardspl custom RUU for flashing roms.
this is from the 1st post of the HARDSPL thread.
http://forum.xda-developers.com/showthread.php?t=431218
NOTE 4: do not use this RUU to flash anything else! this is only intended for flashing the Hard-SPL. use Xperia CustomRUU to flash other ROM images. for example this version: http://rapidshare.com/files/164933503/X1_CustomRUU.zip
Click to expand...
Click to collapse
IF you have finished hard-spl properly it should say 0.72.Olinex, I'd suggest doing hardspl all over again
thanx bro for replying...during hard spl process it never asked for any drivers, i will try this on xo machine and see what happens,
and i dont understand about customs roms, jack's rom is a custom rom right? so which hard spl file do i need ?
najaf363 said:
thanx bro for replying...during hard spl process it never asked for any drivers, i will try this on xo machine and see what happens,
and i dont understand about customs roms, jack's rom is a custom rom right? so which hard spl file do i need ?
Click to expand...
Click to collapse
do the SD WAY, but remember to rename xxxxx.nbh to kovskimg....nbh otherwise it wont load it, se sticky post here in ropm section.
the driver issue is for XP AND VISTA when still in tricolor screen thn vista will install driver needed for hardspl to work (to recognise the device), as i stated the most common is that the hardspl isnt correctly installed.
hope you got it bro..
It sounds like you're getting confused between RUU and NBH
Ruu is the process for upgrading your phone with a new rom.
RUU stands for
Rom
Upgrade
Utility
nbh is the actual rom
there's only one Hard SPL available in the hardspl thread.
Run that again and let it complete, it should work from booloader mode on your phone.
when that is finished and your device in bootloader says 0.72.olipro then you can flash a rom.
If you use the SD Card method the whatever ROM file you choose must be called KOVSimg.nbh and be in the main section (root) of the SD card.
If you want to flash from desktop take the SD card out first.
Download the RUU I linked to in my last post. Extract that and make sure the nbh rom is called RUU_signed.nbh put it inthe ruu folder then start the RUU process.
smaberg said:
do the SD WAY, but remember to rename xxxxx.nbh to kovskimg....nbh otherwise it wont load it, se sticky post here in ropm section.
the driver issue is for XP AND VISTA when still in tricolor screen thn vista will install driver needed for hardspl to work (to recognise the device), as i stated the most common is that the hardspl isnt correctly installed.
hope you got it bro..
Click to expand...
Click to collapse
one too many ks in kovsimg there mate.
thanx guys for replies. i have managed to install the drivers and then i run the hardspl and now its showing :
KOVS110
SPL-0.72.0LINEX
MICROP1-787
MICROP2-707
now i hope it should upgrade it.before doing somthing i want to know after upgrading to jack's rom, the XPERIA logo that comes when starting the device will keep on showing right? the new rom will not remove it?
thanx
najaf363 said:
thanx guys for replies. i have managed to install the drivers and then i run the hardspl and now its showing :
KOVS110
SPL-0.72.0LINEX
MICROP1-787
MICROP2-707
now i hope it should upgrade it.before doing somthing i want to know after upgrading to jack's rom, the XPERIA logo that comes when starting the device will keep on showing right? the new rom will not remove it?
thanx
Click to expand...
Click to collapse
you have windows vista or xp ???
i cant solve this problem with xp
malik bro i have vista, what i did is i connected my device to pc, and without running the hardspl i restarted in bootloader mode (while connected) it automatically installed the drivers when it was in bootloader mode...
after that i restarted my device then i did the hardspl
and now i finished upgrading to jack's rom..job done.!!
now i have 2 problems.
first the panel is gone...how to install it?
2nd the xperia logo what comes in start is also gone...how to install it bcz i need it very much.
thanx
najaf363 said:
now i have 2 problems.
first the panel is gone...how to install it?
2nd the xperia logo what comes in start is also gone...how to install it bcz i need it very much.
thanx
Click to expand...
Click to collapse
read #2 post @ jack's ROM thread
Some cabs and extra files you may need.
1. X1 Panel package to add panel back (divided into sub cabs)
extract the .rar file then it'll show you the panels cab
install Jack Sony X1 Panel Main.cab first then u can install other panels
sorry cant help you with the xperia logo
ok i want to get back to my stock rom..is there anyway to do that?
how to remove this rom so i can install the orignal rom, by connecting with SE software update utility?
this rom is fast stable but its not only me how use this device.so others dont like the way programs and startmenu are showing.
Usb-driver
I have the same problem when trying to flash with XP. I have tried two different computers but have the same problem. It seems that there is some usb-drivers missing. One time i got an error in XP when rebooting the X1 that the usb-device not working correct.
Can not flash by computer
Can not flash using card
The problem occurs when trying to install ROM
Result: When running RUU. Reboot= OK, Tricolour =OK, Process freeze after "loading" apperas (when *.nbh is supposed to start loading.) SPL never finish.
Anoyone knows which driver i need?
don't forget to disable any firewalls and possibly antivirus... This was the problem for me when using Hardspl and Zonealarm suite... So switched off Zonealarm and Hardspl just worked.... [oh and any windows firewalls]
Will try again tonight without FW and antivirus...
However... i have successfully upgraded ROM using SE Update software earlier... The USB worked fine at that time.
najaf363 said:
ok i want to get back to my stock rom..is there anyway to do that?
Click to expand...
Click to collapse
Yes. Just download the generic ROM from the ROM thread and follow the exact same steps as for a custom ROM. Also, look for answers yourself before asking questions that have answers stickied
Spiff76, SE update uses a different way to access your phone. hardSPL can be considered a "hack", which is why antivirus etc. might detect it.
Hmmm... turned of FW and antivirus but same result. RUU freezes after reboot and tricolour. When phone is supposed to start loading new ROM it just freezes and i get a connection-error message.
I believe it has to do with the usb-connection but i can not figure out how to solve it. Have also tried ti install via card without any luck. Same problem remain... i can not get the SPL to finish.
Have any one experienced similar problem and how was it solved. It can not be a biggie but it is really ***.
As said, running this on XP. USB works fine with active sync and in usb to PC-mode.
Spiff76 said:
Hmmm... turned of FW and antivirus but same result. RUU freezes after reboot and tricolour. When phone is supposed to start loading new ROM it just freezes and i get a connection-error message.
I believe it has to do with the usb-connection but i can not figure out how to solve it. Have also tried ti install via card without any luck. Same problem remain... i can not get the SPL to finish.
Have any one experienced similar problem and how was it solved. It can not be a biggie but it is really ***.
As said, running this on XP. USB works fine with active sync and in usb to PC-mode.
Click to expand...
Click to collapse
Most probably YOU HAVE NOT DONE THE HARD-SPL FLASH FIRST
Please CHECK your tricolour screen: the world "olinex" must be there, which means you correctly flahsed the "olinex HARD-SPL" to your device
READ again. It's all written there (sticky posts)
First of all why should i ASK if there WAS AN ANSWER TO BE READ???
I have:
1. Tried to flash using exact intructions in:
http://forum.xda-developers.com/showthread.php?t=431218
Yes, the STICKY POST!
2. I have tried to flash from card whit hard_SPL:
http://forum.xda-developers.com/showthread.php?t=445662
Yes, again the STICKY POST!
And of course:
http://forum.xda-developers.com/showthread.php?t=446070
I have changed cables, ports. The flash seems OK, it says "olinex" in boot-loader but it has never finished.
Have searched the forum for other similar problems and found this thread.
I do not feel the need of repeating myself. Was hoping for some help and answers...
Hello,
After 3 posts without answer in this thread http://forum.xda-developers.com/showthread.php?t=550540
I hope someone can help, see below
repost
Hello,
I read the tutorial here:http://forum.xda-developers.com/showthread.php?t=550540 for SD card only (I'm not a windows OS user)
and try to change my rom for the official HTC win 6.5 FRA but in bootloader mode I only get a white screen with a message in blue "Loading..." and nothing else after 40 min!!
Note: My TP2 is NOT branded
Did I miss something?
I went to the HARDSPL using a friend's laptop with activesync. The tutorial says activesync must be connected to the phone when launching HARDSPL. Once I launch HARDSPL, the connection by activesync is lost and I got ERROR 260
I have tried with activesync on XP and the new application on win &..All same error
I don't think this post is going to last long, since the thread where you originally posted was the correct place for it.
You said you had no answer, but that's not true, you had at least one answer from mskip, and I also made a suggestion to which you made no response other than asking if you should give up.
hi,
I did answer: http://forum.xda-developers.com/showthread.php?t=550540&page=45
Even tried: "- anyone having problems with the device entering SSPL without functional USB port ("ERROR 260 CONNECTION" RUU error), you can get SSPL-Manual-Rhodium.exe from attachment in this post, copy it to the *device* itself and run it. then once the screen is showing black, run the Hard-SPL package on the PC and select Manual"
And same error code 260
It is a GSM phone, right ? Not a Worldphone (CDMA/GSM, which has a SIM card slot but needs a CDMA HardSPL and ROM) ?
Hi,
Yes It's a GSM (with simcard)..I guess.. How to find it out?
Carrying on this discussion in the ROM-flashing sticky, no need to duplicate it here.