It use to be that my bluetooth (jaw bone) would ignore the volume set on the phone. I've screwed something up by where now if I set the phone to vibrate (consequently turning sound off) the headset turns it's volume down as well. I played with the volume control on the phone and indeed when I move the slider up and down, the bluetooth volume is effect.
I played around with some registry setting I read here that could possibly enhance bluetooth audio quality, but now I've got it like this and it sucks.
Any ideas how to fix this?
If I have my Diamond set to silent, and I plug in a headset, music will not be heard because the volume is at 0 due to the profile. Is it possible to have the volume automatically change to 100% (or 50%) when a headset is plugged in, and then go back to whatever it was previously when the headset is removed?
Thanks.
Hi,
I have been having this problem for the last couple of days, for some reason the volume of my ringer has dramatically decreased to the point where i can't hear the phone ring when it's in my pocket (wasn't the case before). When i try to play the ring tone (it's a wave file by the way) using the media player the volume is normal and very loud, the same applies to when i play it from the settings->sounds¬ifications the volume on the ring tone is perfect, but when i receive a phone call the ringer volume is cut down by more than half, i checked the ringer volume and it's set to the max, I also did a hard reset then restored my files using the sprint backup but the problem didn't get fixed, I tried using a different ring tones and the same happens. any help would be greatly appreciated.
There are three volume controls: System, Ring and In call Volume.
Have you checked the System Volume?
If you press up on the hard volume key, you'll see arrow on the top right to switch to the next vol control. Check there.
HTH
ringtone problem
yea all 3 volumes are set to the max level
ringtone volume problem
the phone has the original stock rom from rogers (canada) hope this helps in any way
Have you got any profile managers installed (G-profile, Phoneweaver etc)?
ringtone volume problem
no i dont have a profile managers installed... so i just noticed that when the phone start ringing and i dont pick up, a second before the phone stops ringing the volume of the ringtone increases to the normal level (then stops ringing), the increase of the ringtone volume happens for like a split second after the caller hangs up and the phone stops ringing. hope this helps in any way. Thank you
Sounds like you have a Ringtone delay problem, there are a couple of solutions.
1. Disable HTC dialer (and use the Winmo one instead), can be done using Advanced Configurator 3.3.
2. Try the CAB I've attached, remember to only use WAV as ringtone though.
I would also recommend adjusting Call Forwarding timing to 30seconds. Settings/Phone/Services/Call Forwarding and get settings.
Disabling the HTC dialer is probably going to be the best solution as the HTC dialer is a hungry resource eating monster but I would just try the CAB and adjusting Call Forwarding time. There are some other REG setting as well but I never found them useful.
Whenever my Bluetooth earphones are connected, my volume controls will either be controlled by my earphones and/or the phone which is how it's supposed to be. But most of the time, it'll be controlled by the phone and whenever I change the volume on my earphone, no icon or animation will appear and the volume won't change.
PlsHelpMePPL said:
Whenever my Bluetooth earphones are connected, my volume controls will either be controlled by my earphones and/or the phone which is how it's supposed to be. But most of the time, it'll be controlled by the phone and whenever I change the volume on my earphone, no icon or animation will appear and the volume won't change.
Click to expand...
Click to collapse
I have found the solution, it is to clear the Bluetooth Cache in my apps setting.
I'm running COS 6.1 A.10 on my unrooted/unlocked European X2 Pro.
When I press the physical volume buttons, I very often don't see the sound control popup. Sometimes it appears and I can change the volume, but in most cases it doesn't appear at all. It doesn't make a difference which app I'm using - YouTube, Prime Video. I don't have an active BT device linked or a headset plugged in either. Quiet Time is turned off, all volumes in Sound & Vibration are turned to medium, the default function for volume buttons is set to Media Volume although nothing changes if it's set to Media Volume.
I used to have MacroDroid to change sound settings based on time/location/events but that's uninstalled. I still have Do Not Disturb which mutes my phone during calendar events. Regardless of any such apps, I should still be able to use the volume buttons to adjust the volume but there are no popups most of the time.
I just restarted my phone and the volume popup is back. I know this happened before but after a while it's gone again without knowing why. Does anyone have an idea what could be the reason and how I can get my volume popup back permanently? Thanks for your help.