I found sthg really weird in my unlocked ATT tilt today. I m curently using T-mobile. As many of you know that, you rarely get signal/reception in basement if you are using t-mobile. but today, when i went down to the basement, reception was gone w/ the E icon, then after a while, the E icon was changed to G, then the signal was detected and I could make phone call too. and the carrier on the screen is still T-mobile. Nothing changed except the E/G Icon. I then checked w/ my friend who is also using T-mobile(nokia phone), no reception at all. Does any one know what the difference between E and G icon on top of the screen is? will I be charged for some type of service fee or something if I make calls or use the Tmobile web w/ the [G] icon? please tell me if you guys know anything about it.
thanks in advance...
The "E" is picking up an edge reception, i get it in the UK sometimes because i have a crappy t-mobile signal in my house. When its displayed i cant make phonecalls/txts etc so might be picking up another carriers signal because i dont think t-mob uses edge here. The "G" is gprs just the basic slow phones signal.
G is when GPRS is available, E is when EDGE is available. No extra charge. This could have been easily answered by looking in the manual.......page 29
I guess this may be different for T-Mobile (and could possibly vary on the ROM you're using) but the E on my device is for EDGE service, and G is for 3G service. 3G, obviously, is the better of the two. But I'm on AT&T of course...
Poetique said:
I guess this may be different for T-Mobile (and could possibly vary on the ROM you're using) but the E on my device is for EDGE service, and G is for 3G service. 3G, obviously, is the better of the two. But I'm on AT&T of course...
Click to expand...
Click to collapse
I don't think T-mobile has 3G here in NY.
Thanks for all the replies above
so, the signal of GPRS is stronger than the EDGE? if yes, then we are all able to get reception even if in basement. No need to get verizon anymore... lol
but why can't my friends' phones picked up any GPRS signal? is that because their phones don't support GPRS?
Poetique said:
I guess this may be different for T-Mobile (and could possibly vary on the ROM you're using) but the E on my device is for EDGE service, and G is for 3G service. 3G, obviously, is the better of the two. But I'm on AT&T of course...
Click to expand...
Click to collapse
And then H (HSDPA) just defeats them all.
One Icon to rule them all, One Icon to find them...
Nono
Poetique said:
I guess this may be different for T-Mobile (and could possibly vary on the ROM you're using) but the E on my device is for EDGE service, and G is for 3G service. 3G, obviously, is the better of the two. But I'm on AT&T of course...
Click to expand...
Click to collapse
No no no, g is not 3g, G is GPRS, the slower version of EDGE, thats the reason why you can call in your basement now!
G is GPRS
E is EDGE
3G is UMTS
H is HPSDA
first is the slowest, last is the fastest, so if the fastest is not availible, it switches to a slower one, like happened in the TS situation
My icon used to pretty much always be on 3G, sometimes switching to E when I drove to my brothers house which is about 25 miles away. But recently I haven't been seeing 3G at all, but only H. I did see E a couple days ago, but I haven't seen 3G in more than a week now. I thought H was only supposed to show up when you were using a data network or something? At least that's what I read somewhere on here a while ago... Any explanations?
that H is wat you want to see
first H shows up when downloading data means you're using HSDPA, but is H shows up when u're not downloading data, you have HSUPA too
Ya, as XtreMe_G indicated this is easily answered by opening up the manual.
XtreMe_G said:
that H is wat you want to see
first H shows up when downloading data means you're using HSDPA, but is H shows up when u're not downloading data, you have HSUPA too
Click to expand...
Click to collapse
Yeah, I know HSDPA is what I want to see the most, but when the hell did AT&T have HSUPA? I live in the Washington DC/Northern Virginia Metro area... Anyone else from the area noticing this?
And as for the OP's question about E and G, there is no difference between signal strength and ability to make voice calls. E just means that the cell offers Enhanced G.
Whether you see a G or and E (or 3g or H) is dictated by the data connection offered by the cell - which has no baring on voice at all.
If you have any signal, you should be able to make voice calls - the speed of the data connection (ie for web/email etc) is the only thing indicated by the Letter - except that 3g/H can also do simultaneous voice and data where G (and E) can't.
swiftgs said:
No no no, g is not 3g, G is GPRS, the slower version of EDGE, thats the reason why you can call in your basement now!
G is GPRS
E is EDGE
3G is UMTS
H is HPSDA
first is the slowest, last is the fastest, so if the fastest is not availible, it switches to a slower one, like happened in the TS situation
Click to expand...
Click to collapse
That's what I thought, but then I tested my data connection speeds and when I'm supposedly on basic GPRS the speeds are much greater than anything either GPRS or EDGE could accomplish (unless EDGE was having a perfect day).
I did notice however that it only shows G instead of 3G when I force the phone NOT to use 3G while 3G is available in the area. If I allow it to use 3G service it shows up as "3G" and the speeds remain the same. As soon as I force it not to use "3G" it shows up as just "G" but the speeds stay the same.
"E" or EDGE always seems to be indicative of the correct speed. But for my device it switching between G & 3G are one in the same, and the speed doesn't change at all.
Could just be a glitch with the software on my phone, but that's how it is for me.
Exousia said:
Yeah, I know HSDPA is what I want to see the most, but when the hell did AT&T have HSUPA? I live in the Washington DC/Northern Virginia Metro area... Anyone else from the area noticing this?
Click to expand...
Click to collapse
they are turning it on as we speak, i saw it somewhere but i cant find it right now....
unwired4 said:
- except that 3g/H can also do simultaneous voice and data where G (and E) can't.
Click to expand...
Click to collapse
Thanks for that.
That will be the reason that when I used a tomtom one and got traffic via my bluetooth phone, a traffic update would kill any call I was making.
I assume I am correct in also expecting my TyTn II to ignore voice calls (or drop gprs data connection) if I am using the TyTn II for internet access for my laptop and a voice call comes in?
I sometimes get the E but as far as i know we dont have Edge in t mobile UK.
how do you remove the G?
Exousia said:
My icon used to pretty much always be on 3G, sometimes switching to E when I drove to my brothers house which is about 25 miles away. But recently I haven't been seeing 3G at all, but only H. I did see E a couple days ago, but I haven't seen 3G in more than a week now. I thought H was only supposed to show up when you were using a data network or something? At least that's what I read somewhere on here a while ago... Any explanations?
Click to expand...
Click to collapse
Same thing here in Baltimore. I have not seen my 3G icon in a while, only the H.
data speeds seem to be the same though.
My G Icon changes to E Icon
Hello,
I have a small problem...
First I will Switch ON my wizard. After Switch ON I will see a G Icon at top of the today screen ( That is correct ). When I press the power button, the screen goes off (i.e Goes to Sleep Mode ) and again I press it to wake up. but now the G icon will change to E icon.
I not understanding why this happens.........
Also when i connect to GPRS internet but it shows as I am connected to EDGE with E icon ( This happens on when I wakeup the device )
My probem is that why the icon should change when I wakeup the device.
To confirm you that, I have also disabled the "EnableDifferGprsEdgeIcon" setting in registry.
This problem will not occur in wm5 but only in wm6 or wm6.1.
In wm5 There is no E icon or it is not showing as "connected to EDGE" when I connect to GPRS internet.
Please any one help...............
Thanks in advance
Srikanth.K
I did the kaisertweak to enable the H network or whatever (yes i don't understand it)
the network still says E or 3G . It said that all the time, for the last few days.
Then I was messing around trying to get this gps to work in google maps and I noticed it switched to H. but now it's back to 3G. is this all normal?
Ive noticed that too..
no idea what it means
what operator are you with in what country
check with them to see if you have hsdpa reception my hsdpa is enabled but since i dont have coverage i stay at 3g
hsdpa is a better version of 3g
its often called 3.5g 3g+ or mobile broadband so basically all the twaek is is to let your phone get the faster connection but only if your operator has the signal to do so
The H icon (HSDPA) is a step up from 3G it allows anything up to 7.2Mbs transfer but the HTC instead of contantly allowing this to be active thus creating massive battery drain only allows it when a data connection is active and data is being transferred any other time and you will only get G, E or 3G
3g alows ypou to have video conferences but H mean HSPD fast internet 3,6Mbit or 7.2Mbit depands that the difference i belive.
exactly just because you enable it doesnt mean you can recive it
I turned hsdpa with kaiser tweak also. I noticed it will only connect to hsdpa when transferring data (IE, emails, weather, ect.). Otherwise it will go back to 3G when on the today screen, or offline tasks. I guess its to conserve power?
Maybe thats what your seeing?
ok thanks, looks to be normal =]
My 3G and HSPDA Keep switching when there is an active internet connection.
when im not acutally using the internet its just 3G then when i search it turns H on is this some kind of power saving feature or is there a fix, as i would rather have H on always.
It's supposed to do that. HSPA is incredibly power-hungry, so would you want that?
Thanks for the reply mate.
There is an option to change it to use only H or 3G in the settings, if you really want to.
My carrier has bad 3G operation, whilst HSDPA works fine. The problem is that phone sometimes switches between 3G and H, and when it does switch to 3G, there is no internet until it swithes back to H or down to E. I'm almost sure that this is caused by carrier, and I can't fix it with firmware. So I would like my Tab to avoid 3G mode at all, while using H and E. Can I set it to do so?
3Flight said:
My carrier has bad 3G operation, whilst HSDPA works fine. The problem is that phone sometimes switches between 3G and H, and when it does switch to 3G, there is no internet until it swithes back to H or down to E. I'm almost sure that this is caused by carrier, and I can't fix it with firmware. So I would like my Tab to avoid 3G mode at all, while using H and E. Can I set it to do so?
Click to expand...
Click to collapse
Unfortunately, it's impossible, you can either choose "H" & "3G" with wcdma/umts or "G" & "E" with GSM in Mobile Networks. You can't choose to leave out 3G when it's doing H, cause both of them are under wcdma mode.
Of cause, if you leave your "Network mode" to auto, it will jump around gsm and wcdma when it see fit. By choosing it to run GSM mode only, will keep your network connect to "E"/"G(gprs)" ONLY; Or WCDMA for "H"/"3G" ONLY.
helo
3Flight said:
My carrier has bad 3G operation, whilst HSDPA works fine. The problem is that phone sometimes switches between 3G and H, and when it does switch to 3G, there is no internet until it swithes back to H or down to E. I'm almost sure that this is caused by carrier, and I can't fix it with firmware. So I would like my Tab to avoid 3G mode at all, while using H and E. Can I set it to do so?
Click to expand...
Click to collapse
im from malaysia also,im using samsung g5..in my opinion its the the phone or tab firmware or rom problems..because im using maxis and digi broadband..both network are having problem..3g and hsdpa both switch on and back 3g h 3g h..not stabil and anoyying..
Guys I have an odd problem.
Where I live, the signal on the HTC One switches erratically and constantly between H+, H and 3G. At every switch of course the data connection goes offline. It's driving me crazy.
Is there a way to force the phone to one of the three: 3G or H or H+?
Please see image 01.
I've tried going into *#*#4636#*#* but the choices baffle me (see image 02). I've tried a few of the available choices but it seems that 3G, H and H+ fall into the same category.
It's probably a dead end, I can't imagine what else to do ..... has anyone else had the same issue?
The 3G logo means it's on voice only, and H+/H means there's data incoming/outgoing. They're using the same radios and frequencies, it's more like an idle state when it shows 3G. 3G will still periodically go up to H+/H to check for any incoming data then goes back to sleep at 3G.
I have the same problem with my connexion. It is only stable when I have the "3G" symbol. I did not find a way to force "3G". It seems the switch to "H" is on demand...
mrechte said:
I have the same problem with my connexion. It is only stable when I have the "3G" symbol. I did not find a way to force "3G". It seems the switch to "H" is on demand...
Click to expand...
Click to collapse
It's normal behaviour, if you have a good H connection it will switch to this when there is data traffic but when there isn't it will switch between 3G and H