Oh no, power button went out... - Touch CDMA Android Development

Okay, my power button went out, which seems from previous posters that it spells the end of the phone. However I pryed mine out, and am SOMETIMES able to get my power button to respond by sticking a knife in there.
My question is can anyone get my an NBH that remaps my power key (or can I make one myself) to another key? I'm not sure what key would be best, I'm guessing power/back, knowing that I'd no longer have the ability to go back, but I only need the work around until the end of July when I can get a new phone... Thanks.

fldash said:
Okay, my power button went out, which seems from previous posters that it spells the end of the phone. However I pryed mine out, and am SOMETIMES able to get my power button to respond by sticking a knife in there.
My question is can anyone get my an NBH that remaps my power key (or can I make one myself) to another key? I'm not sure what key would be best, I'm guessing power/back, knowing that I'd no longer have the ability to go back, but I only need the work around until the end of July when I can get a new phone... Thanks.
Click to expand...
Click to collapse
if only there was a Zimage of the super old keymap around

Do you mean a button on the top of the phone?
I got a Polaris (so maby this is not helpful).
But if you got some knowledge with hardware and got calm hands you maby can open your phone.
I had the same problem and my button was broken off from the mainboard. But it was really easy using a soldering iron to fix it.
.......
You should consider this as a possible solution... Its not to hard to open the phone and soldering isnt that hard either. Maby you got a friend that can do this. Or someone in your city does repairs of this kind (each electrican should be able to) its just fixing 4 dots on a 2x2mm big button..

dertester123 said:
Do you mean a button on the top of the phone?
I got a Polaris (so maby this is not helpful).
But if you got some knowledge with hardware and got calm hands you maby can open your phone.
I had the same problem and my button was broken off from the mainboard. But it was really easy using a soldering iron to fix it.
.......
You should consider this as a possible solution... Its not to hard to open the phone and soldering isnt that hard either. Maby you got a friend that can do this. Or someone in your city does repairs of this kind (each electrican should be able to) its just fixing 4 dots on a 2x2mm big button..
Click to expand...
Click to collapse
I have it open already... I'm guessing I solder this button to the metal piece... this is pretty precise work but I'm going to try it, nothing to lose...

Well hell, I got it on there, but it's shorted, the power button is always down and I can't figure out how to fix it... I don't understand how this button works as even the design of it makes no sense.

Ok, so I never got it, pretty sure my switch is bad... I can short it out, and use the power button so I have wires sticking out, I'm still looking for an NBH that will let my move my power button to something else... like maybe long hold volume up?

Wonder if it's possible to do something with they keylayout files?
dzo?
http://forum.xda-developers.com/showthread.php?t=695936

Actually, the perfect power button would be the d-pad center button as I don't think I've EVER hit it before...
If someone can help me try to change it, I'd appreciate it. I know the method above won't work as the Vogue gets it's keymap from the kernel. I did some searches for unsungboxer but never found where it was described how to edit the keymap. All I know is it supposedly requires linux.

Related

Want to FLash but powerbutton don't work

Hello Everyone,
I have a BA and I want to flash it but the power button dose not work..opened it up and found that the mechanism under the button has dropped and hanging on by a thread. The device works but I need the power button to get into bootloader mode.
So the question is this: is there a way to get into bootloader without using the powerbutton?
yolandanelson31 said:
Hello Everyone,
I have a BA and I want to flash it but the power button dose not work..opened it up and found that the mechanism under the button has dropped and hanging on by a thread. The device works but I need the power button to get into bootloader mode.
So the question is this: is there a way to get into bootloader without using the powerbutton?
Click to expand...
Click to collapse
From Jadel....
First, some advice. Several people have asked this question and it has been responded to in other threads. On forums, ALWAYS try and use the search function before asking. It might save you some time, and it also may give you further ideas or solutions to the problem. Now on to the response I gave someone else last year. Read the whole post.
IT IS POSSIBLE!
BUT DO THIS AT YOUR OWN RISK!!! I'M NOT RESPONSIBLE FOR ANY DAMAGED OR FRIED PDAs
I know because I myself have done it on an I-mate (Himalaya). It took some trial and error but I am now running WM6. In my case though, I had to completely remove the power button from the device. The previous owner dropped it on its head, and I got it for free, unfortunately most of the top is missing, including the power button.
SO, on to how I did it. I took a paper clip (metal) and put it about 1cm down, slightly to the right of where the power button used to connect to the motherboard. Make sure you have turned your XDA/IMATE on before doing this. You'll find that when you find the right area, your device will turn off, or the screen will go dark (like holding the power button for a second or giving it a quick tap).
If you manage to hold it there for the right period of time, while pressing the other bootloader buttons, then you will be able to enter bootloader.
This took me close to an hour to get just right, on both occasions I have done it, but it eventually worked.
Note: I have no idea how exactly this worked, but it did. My IMATE was useless without me updating the rom, so I had no worry about frying it if I did something wrong, that is why I was OK with playing around with its insides. BEWARE that you MAY DO DAMAGE to the device.
Good luck.
If you have no clue just don't post!!
First off I have searched here and the internet as a whole and your suggestion didn't work! I have taken apart and modified to add a camera to my working BA ( yeah I got 3 of them) so "..playing around with its insides. BEWARE that you MAY DO DAMAGE to the device.." is no worry of mine. Second off, if you had taken notice I have been on this board since Feb 2007 and I have only had to ask 3 questions, which means my searching skills might just be working on some level.
Maybe I should have been more specific: is there a software boot loader for the sx66?
David389 said:
From Jadel....
First, some advice. Several people have asked this question and it has been responded to in other threads. On forums, ALWAYS try and use the search function before asking. It might save you some time, and it also may give you further ideas or solutions to the problem. Now on to the response I gave someone else last year. Read the whole post.
IT IS POSSIBLE!
BUT DO THIS AT YOUR OWN RISK!!! I'M NOT RESPONSIBLE FOR ANY DAMAGED OR FRIED PDAs
I know because I myself have done it on an I-mate (Himalaya). It took some trial and error but I am now running WM6. In my case though, I had to completely remove the power button from the device. The previous owner dropped it on its head, and I got it for free, unfortunately most of the top is missing, including the power button.
SO, on to how I did it. I took a paper clip (metal) and put it about 1cm down, slightly to the right of where the power button used to connect to the motherboard. Make sure you have turned your XDA/IMATE on before doing this. You'll find that when you find the right area, your device will turn off, or the screen will go dark (like holding the power button for a second or giving it a quick tap).
If you manage to hold it there for the right period of time, while pressing the other bootloader buttons, then you will be able to enter bootloader.
This took me close to an hour to get just right, on both occasions I have done it, but it eventually worked.
Note: I have no idea how exactly this worked, but it did. My IMATE was useless without me updating the rom, so I had no worry about frying it if I did something wrong, that is why I was OK with playing around with its insides. BEWARE that you MAY DO DAMAGE to the device.
Good luck.
Click to expand...
Click to collapse
I lifted this directly form another site I have subscribed to
http://relaysgoldens.com/sx66/tools/ROM_Update_Tools.rar

Someone who took their G1 apart - help me out!

Hello
I've got my greedy hands on G1. Phone was free so I can't loose on that lol. Gal who gave it to me said that all it does for her when she powers it up is going into Hboot screen I applied dreaimg.nbh, got it to boot into rc29 and realized that I had no simcard in it. I powered it off, put sim in it and powered it back on and now I'm looking at Hboot screen again. I can boot into recovery just fine though but selecting reboot from that menu takes me back to rainbow. I can also reboot with 3-finger salute but again, it takes me to Hboot.
I have a feeling that this is a problem with camera button rather then software, did anyone fix this successfuly? Is there a way to physicaly disconnect camera button from main motherboard? Any insight is appreciated.
I'm not a noob, I can troubleshoot software issues but i've never taken this phone apart so I'm clueless.
Thanks in advance.
Ok, so I found this thread and I guess there's no easy way to just disconnect camera button. I still would like to know if anyone recovered from such a problem. Thank you in advance.
I have not taken the G1 apart, but I was a hardware troubleshooter for much of my professional career. My first guess is that the button is stuck not shorted. Always try the simple things first. Look at the button cover, does it protrude from the case slightly, or does it look pressed in. Even if the button cover is not pressed it, it is possible the button itself is stuck. in this case, tap it against a hard surface a few times. Hey it was a free (broken) phone, what have you got to loose. You can probably tap what would seem to be a little too hard without hurting it. If that doesn't work, then you may need to take the phone apart and check the button state. Does it push in, pop back out. If not you may be able to physically pull the button back out. If it does, then it's possible the button is messed up/shorted inside. By the looks of the pictures, the only fix is to unsolder the button.
Those are the steps I would take. Always start simple and work up from there. And always be open to something that seems unrelated that you may find along the path but ends up being the problem.
Hope it helps
scott
Scott
I don't have t5/t6 screwdrivers handy so I did not quite take it apart. I did nowever pry the camera button (plastic part of it) out slightly, enough to see inside. I found that the actual button does work, i.e. it goes in and pops out on it's own. I tried tapping it as well, harder then most people would probably. Still the same problem. Oh well, I have one more trick up my sleeve. When I got the phone it was super cold because it was left in the car overnight (way below freezing temps, those MN winters you know) so may be I can do it again... who knows, like you said, what do I have to loose?
Thank you for your opinion.

HTC Touch power button broken. Stuck on Droid. What to do?

I dropped my phone yesterday, and the power button doesn't do anything now. It doesn't seem to move much, either. I popped a little of it out using the stylus, and couldn't find any wires so I don't think there's a solution. The button itself seems fine, but I think it got dislodged a bit from whatever mechanism (spring or latch) that tells it to turn on or w/e. Looks impossible to open up the device. (don't see any screws. looks soldered in)
Anyway, the phone itself works. I resetted it and it'll load up Android fine. I just can't get into Android because you need to press the power button to get out of the standby screen.
Is there any way I could
a) assign a new button in Android (say the center button?)
b) fix the button (or if I brought it to a Sprint store would it cost less than the phone? ($60))
c) get rid of Android and go to Windows without using the power button (power+reset code)
Thanks for the help!
mozillameister said:
I dropped my phone yesterday, and the power button doesn't do anything now. It doesn't seem to move much, either. I popped a little of it out using the stylus, and couldn't find any wires so I don't think there's a solution. The button itself seems fine, but I think it got dislodged a bit from whatever mechanism (spring or latch) that tells it to turn on or w/e. Looks impossible to open up the device. (don't see any screws. looks soldered in)
Anyway, the phone itself works. I resetted it and it'll load up Android fine. I just can't get into Android because you need to press the power button to get out of the standby screen.
Is there any way I could
a) assign a new button in Android (say the center button?)
b) fix the button (or if I brought it to a Sprint store would it cost less than the phone? ($60))
c) get rid of Android and go to Windows without using the power button (power+reset code)
Thanks for the help!
Click to expand...
Click to collapse
There are 4 Torx screws (1 under the warranty void sticker) essentially at every corner, so if you get a small enough torx screwdriver you can open it up
Here is a guide albeit in Russian, but the pictures are self explanatory
http://www.pdacenter.ru/razborka/razbor_htc_touch/
Is there any way I can reassign the button to the Back button or something? I need a quick fix so I can use the phone now for calling. Its probably built on to the motherboard because there's no wiring from the looks of it. Not sure where to find such a screwdriver, but I'll look into it.
I had a similar problem with my camera (back) button. It was a fairly easy fix. You will need a tiny Torx to get it open. There is a complete teardown thread on this site to help guide it. Once I had the right Torx driver, it took a few minutes. The switches are surface mounted and are held in place with clips. I had to bend the clips back into place and then reflow the solder joints with a soldering iron. I dropped some solder onto the clips to hold them together.
I tried to roll an alternate ROM with different key assignments...the build process is not well documented, IMO. I asked and was basically told to go make friends with a developer.

Can't access bootloader/Broken camera button

My camera button is shot and the regular method of accessing the bootloader is impossible for me. Are there any other options for me?
Sorry, no.
Sputnikk23 said:
My camera button is shot and the regular method of accessing the bootloader is impossible for me. Are there any other options for me?
Click to expand...
Click to collapse
You mean when you do power + camera?
*M* said:
You mean when you do power + camera?
Click to expand...
Click to collapse
Yes, I believe that's what he means. Sputnikk23, do you have Windows Mobile installed or Android? If you have Windows Mobile installed, it can definitely be done. If you're on Android, I'm not so sure.
it was stock rom wm 6.1;
currently installing nfs
I ended up taking it apart to try to fix button; accidentaly broke it off. poked the button out, put it back together and now I just short circuit it.
doing it as per the guide to install android though
hopefully i don't need the camera button for anything essential...
http://handheld.softpedia.com/get/System-Utilities/Enhancements/BootLoader-85221.shtml
crap... you need it to back out of stuff.. can you change that in android?
i'm in qwerty keylayout in /system/usr/keylayout and i can't figure out what my end key is mapped to. when i press it it blacks out the phone? sometimes comes back by itself, sometimes i have to hit power. just comes back to whatever i had before it blacked.
and what is the left softkey supposed to do? and what is the "home" button? the power key?
and i cannot get win7 to install the usb drivers. implies they are for 64bit when they are clearly not.
I DID IT! I remapped the "End" key to "Back" instead of "END CALL".
You can end call with the touch screen, only thing I"m missing is manual sleep which it will do auto in 30 secs. Anyone know of a widget I can put on home screen to do it manually?
Also, shouldn't SOME key take me instantly back to home screen?
If anyone needs instructions for layout change - I can write up a tutorial.
key- re-map!
i would love a tutorial! ive been tryin to figure out how to do this for a while!
im running NAND, Myns warm donut
The camera button on my Vogue was sketchy and then finally died. I opened it up and the microswitch had dislodged. I am not great at soldering, but it was an easy fix. I just pushed it back into place, bent the retaining "ears" back around the switch, soldered the ears together to hold it better, and finally just touched the leads to the switch to reflow them. It took much longer to open the phone and put it back together than it did to resolder. It took maybe 30 minutes, start to finish and it was well worth it, IMO.

[Q] Power button not clicking

Hey guys
Just wanted to know if there is any way I could fix the power button to make it click. I picked up a Nexus 6 about a month ago used. The power button has no click to it,but I thought that was normal. But just today, I thought I would read into it because I noticed the volume buttons where clickey(never really use them) and that the power button should be too. How or can I fix the power button?
Thanks
hmm the power buttons works but there is no click?
Replace the power button/volume rocker flex cable it's all one unit. Easy to replace.
graydiggy said:
Replace the power button/volume rocker flex cable it's all one unit. Easy to replace.
Click to expand...
Click to collapse
Hahaa. For you. I'm not opening my ****. If it works don't need no click.
It will fail soon enough.
I'm a technician. When these types of buttons lose the click, they fail soon after.
alobear said:
hmm the power buttons works but there is no click?
Click to expand...
Click to collapse
That's right. It feels terrible to press, plus some times when I press the power it doesn't turn on and I'm not sure if I pressed it hard enough....so usually I press very hard to make sure I don't have to press again. 90% of the time it comes right on.
prdog1 said:
Hahaa. For you. I'm not opening my ****. If it works don't need no click.
Click to expand...
Click to collapse
Well, I did already take of the back to put on a real leather slickwrap skin(with replacement back) and the stock back was really on there(ripped off a piece of the plastic that stuck to the back cover), but I managed to get it off. Sucky part is, I'd have to rip it back off again and I'm not sure it will stick as well if I do that.
I just need to find the part I guess. I do think that eventually it might stop working.
pretty sure you can use a hair dryer or heat gun and get the back cover off rather easily, should be able to reapply it back again. here is a link to the power and volume buttons.
http://www.etradesupply.com/motorola-nexus-6-power-button-and-volume-button-blue.html

Categories

Resources