Related
So my tilt fell off my clip while I was out in the yard and before I realized it, I had walked all over it. Everything seems to function but the LCD colors area all jacked up. It is faded (mostly white), funky colored, and hard to see what is going on. Attached is a picture of it. Do you think it is just the LCD? (I can replace that for 70 bucks from blackberry8100parts.com). Or do you think I've killed something else?
Any advice would be fantastic before I waste 70 bucks getting a new LCD.
Thanks,
Alan
I just want to know what kind of clip you had?
knytphal said:
I just want to know what kind of clip you had?
Click to expand...
Click to collapse
It was seidio's holster. I really like it but it is def easy to knock the tilt out of it.
If you are willing to open the tilt up to replace a broken LCD then I would go ahead and open it NOW and see if you find other damage. You are looking for anything cracked. There are manuals for the unit in the wiki. If you haven't cracked anything else then your probably ok but the only real test is to buy and LCD and try it out. I assume that slide action of the keyboard tray is as it was before you stepped on it? It it anyway stiff or off? Does it tilt up the same way and with as much ease as before?
Everything seems to slide and tilt up without a problem. There is no looseness, friction, resistance, etc.
I have read through instructions on how to take it apart. Only thing is that I'm going to get a new LCD, I need to use the phone till I get it It is usable, just a bit tricky ;-) I'm a bit nervous taking a part twice. I also don't have the right tools which would come with the LCD.
Guess I'm just going to have to buy the LCD. I can always resell it if need be.
Alan
Maybe try and open it up to see if you have a loose connector because that color thing is weird. Usually you would have a crack on the screen and you would see the crack but instead you seem to be missing some colors which leads me to think that the connector might have become unseated a little.
Any update on this? Something happened to my tilt last night and it's doing the same thing!
Probably just the LCD but it might just be a loose flat multi connector. If there's no warranty then as suggested above you could dismantle just to be sure you do actually need a new LCD. In the worst case scenario you could find that compnents on the d/pad daughter board are damaged. You can only really tell by internal inspection.
Mike
I went ahead and purchased a new LCD from fonlogix figuring I could always keep the LCD as a just in case or even resell it. It was suppose to have come with the t5 torx driver and the case opener but the case opener wasn't in the package. I emailed them and they said they were out and didn't want to hold the shipment. They are suppose to be sending me one though. I would rather not try dismantling without it because I don't want to risk anything (nor do I want to try with my finger nails). I'm hoping to receive the tool very soon so when I do and I get it dismantled, I'll post back.
I think just maybe the ribbon cable that connects the LCD to the mobo has come lose.
I know on my Hermes, this was located under the center buttoin, and when I would press it hard enough it would make a secure connection, and it would display normal color quality, and when I let go it would become like a 2bit color quality
Fixed! I went ahead and replaced the LCD and now it works. I examined all connections as best I could as I went along and didn't find any loose ones so I'm not for sure if it really was a loose connection or a broken LCD. Regardless, I'm not going to take it apart again to find out! I'll keep my old LCD as a backup and if it becomes necessary, test it out
Thanks!
Alan
in the future you could use a program like my mobiler I have attached it to check out your tilt that is what I did when the screen broke you can view your tilt on your pc with out the screen
you should post a video on how easy it is for the tilt to come out of the seidio holster... i was actually thinking about getting it.... but i play a lot of sports so if it would knock out easily then it wouldnt really be good for me.
The problem with the seidio holster is that it is open at the top on the sides. Thus, if you or something hits or puts pressure from the side at the top of the tilt (where the power, ptt, and ok buttons along with the wheel are), it pops out of the case.
Tilt LCD Replacement Video
www.blackberry8100parts.com
now has Tilt LCD Video replacement instructions in High Definition.
check it out
belize2004 said:
www.blackberry8100parts.com
now has Tilt LCD Video replacement instructions in High Definition.
check it out
Click to expand...
Click to collapse
Thanks for the link. Did anyone download the plugin? I'm getting tired of all these diffent plugins, they will slow your system down over time.
I'm assuming I smashed my At&t tilt or something, there is no cracks on the screen or anything, but the pic below shows the display I get. I'll have the phone for about a year in about 2 weeks. Anyone have an idea as to how much At&t or HTC will charge to fix this or am I better off buying a new phone? Or any ideas as to what could be broken and how it can be fixed? It doesn't allow me to do a hard reset. Thanks
well i don't know if warranty will cover it or not but you are still under your one year warranty so you could try to get a replacement. Its hard to say what could be causing it. You can check out mike channon's articles on disassembling a kaiser.
Good luck.
brianlb said:
I'm assuming I smashed my At&t tilt or something, there is no cracks on the screen or anything, but the pic below shows the display I get. I'll have the phone for about a year in about 2 weeks. Anyone have an idea as to how much At&t or HTC will charge to fix this or am I better off buying a new phone? Or any ideas as to what could be broken and how it can be fixed? It doesn't allow me to do a hard reset. Thanks
Click to expand...
Click to collapse
Well to my trained eye, it looks as though you have actually cracked the lcd screen. This damage isnt generally covered by any manufacturers standard warranty. Unless you purchased an extra warranty including accidental damage, I think its up to you to repair yourself unless you want to spend 400USD + for the repair. Taking it apart isnt terribly difficult and I have seen links to lcd screens posted all over for no more than 100USD. Check Ebay also.
http://cgi.ebay.com/LCD-Replacemet-...39:1|66:2|65:12|240:1318&_trksid=p3286.c0.m14
Here is one for 45 USD
Hope this helps ya
pyraxiate said:
Well to my trained eye, it looks as though you have actually cracked the lcd screen. This damage isnt generally covered by any manufacturers standard warranty. Unless you purchased an extra warranty including accidental damage, I think its up to you to repair yourself unless you want to spend 400USD + for the repair. Taking it apart isnt terribly difficult and I have seen links to lcd screens posted all over for no more than 100USD. Check Ebay also.
http://cgi.ebay.com/LCD-Replacemet-...39:1|66:2|65:12|240:1318&_trksid=p3286.c0.m14
Here is one for 45 USD
Hope this helps ya
Click to expand...
Click to collapse
I don't see a crack in the screen. Can there still be a crack in it that isn't visible or not noticeable until you take it apart? If that's the case I'll either buy a new screen or just buy a new phone on ebay for 200bux. Also anyone have any recommended sites on how to replace the screen?
This raises a great question for me. i work in a clean room/static sensative environment and repair and calibrate many different types of electronics (mostly signal generators & spectrum analyzers). I was wondering if anyone here has actually attempted to replace a LCD screen with success. And if so, how complicated the process was. I have downloaded the schematical drawings and have found replacement parts for the kaiser online for extremely cheap. i will post the site as soon as i find it again.
I did a screen replacement on a Wizard, and it wasn't that difficult. just make sure you don't break anything while trying to pry small pieces off to get to the screen.
Stu_Can_Sam said:
This raises a great question for me. i work in a clean room/static sensative environment and repair and calibrate many different types of electronics (mostly signal generators & spectrum analyzers). I was wondering if anyone here has actually attempted to replace a LCD screen with success. And if so, how complicated the process was. I have downloaded the schematical drawings and have found replacement parts for the kaiser online for extremely cheap. i will post the site as soon as i find it again.
Click to expand...
Click to collapse
ITs easy as hell.
I've done it two times with success.
Its only matter of two connection belts and thats all at all .
Screen replacement is really easy here.
brianlb said:
I don't see a crack in the screen. Can there still be a crack in it that isn't visible or not noticeable until you take it apart? If that's the case I'll either buy a new screen or just buy a new phone on ebay for 200bux. Also anyone have any recommended sites on how to replace the screen?
Click to expand...
Click to collapse
Generally you will NOT see a physical crack on the surface. The surface is actually JUST a digitizer ( a separate piece which is built into or ontop of your LCD for input purposes ). The digitizer is basically your touch screen portion of the LCD. What is actually cracked is the thin film below that which contains all of the liquid crystals.
As far as the replacement goes, I believe it is Michael Channon who has the step by step instructions on how to disassemble and replace the LCD. It isnt a hard task from what I can tell. I had taken my hermes ( Tytan ) apart so many times that i could do it in my sleep. Its not a terribly difficult process.
Here is Michaels Guide
Its not in English but its not hard to follow the pictures. He has done a great job at documenting the procedure.
If you are a bit scared to try it yourself, have a geeky friend do it for you ( maybe get him a date to a movie or something lol )
It should only cost you no more than 50$USD to repair ( Minus the bribe for a date lol )
Hope this helps you out !
pyraxiate said:
Generally you will NOT see a physical crack on the surface. The surface is actually JUST a digitizer ( a separate piece which is built into or ontop of your LCD for input purposes ). The digitizer is basically your touch screen portion of the LCD. What is actually cracked is the thin film below that which contains all of the liquid crystals.
As far as the replacement goes, I believe it is Michael Channon who has the step by step instructions on how to disassemble and replace the LCD. It isnt a hard task from what I can tell. I had taken my hermes ( Tytan ) apart so many times that i could do it in my sleep. Its not a terribly difficult process.
Here is Michaels Guide
Its not in English but its not hard to follow the pictures. He has done a great job at documenting the procedure.
If you are a bit scared to try it yourself, have a geeky friend do it for you ( maybe get him a date to a movie or something lol )
It should only cost you no more than 50$USD to repair ( Minus the bribe for a date lol )
Hope this helps you out !
Click to expand...
Click to collapse
Thx, I'm gonna give it a shot. I went ahead and bought the screen off ebay from the post by pyraxiate. Worst case I mess it up and buy a new phone of ebay for 150-200, which is what I originally thought I'd have to do, so this at least gives me a chance to save some $$$
brianlb said:
Thx, I'm gonna give it a shot. I went ahead and bought the screen off ebay from the post by pyraxiate. Worst case I mess it up and buy a new phone of ebay for 150-200, which is what I originally thought I'd have to do, so this at least gives me a chance to save some $$$
Click to expand...
Click to collapse
Let us know how it goes
Glad I could help
Got it all done, actually my pops did it. Works great, he took it apart just like the Mike Channon pics show, don't know if you had to do all of it or not just to replace the screen, but he did. Only one little annoying thing now that it's back together is that a small part of the black plastic out case hangs out just a tab and isn't flush, which makes it a little annoying when hitting the power/standby button on the right side of the phone. But I can learn to live with that I think. thanks for all the help.
congratulations!
good to hear you've achieved a successful repair!
correct me if i'm wrong...are you saying that the two halves of the phone (screen and keyboard) don't align properly when the keyboard is closed? if so, i remember a thread in this section of the kaiser forums that details (with pictures) how to possibly fix that particular problem!!!
"search and ye shall foundeth it !!!"
brianlb said:
Got it all done, actually my pops did it. Works great, he took it apart just like the Mike Channon pics show, don't know if you had to do all of it or not just to replace the screen, but he did. Only one little annoying thing now that it's back together is that a small part of the black plastic out case hangs out just a tab and isn't flush, which makes it a little annoying when hitting the power/standby button on the right side of the phone. But I can learn to live with that I think. thanks for all the help.
Click to expand...
Click to collapse
Im glad i could help Im also glad to hear the phone is up and running again
As was stated before, there is a thread for the case not aligning. I did some quick looking but to no avail. If i come across it ill be sure to post it
I'm not sure if I'm explaining it correctly. But it's basically the outer case, and around the power button it's not flush. Not sure if you can tell from my pics. I tried also doing a search w/no luck. I'm sure there is some specific name or something other than case that it's under.
When i replaced my faceplate i had the same problem. all i did was push it in...kinda hard, and it poped in, or you could use a plasic flathead and pop it back in...
DemoShadow said:
When i replaced my faceplate i had the same problem. all i did was push it in...kinda hard, and it poped in, or you could use a plasic flathead and pop it back in...
Click to expand...
Click to collapse
I tried that, and it doesn't seem to pop in at all.
I think its just like DemoShadow said. I dropped mine once and it seems to be a similar issue. I also just pushed really hard to get it to pop back in. I think its just that clip isnt in place as it should be when it was put back together. If anything, try to take it apart and put it back together
kristoff_sz said:
ITs easy as hell.
I've done it two times with success.
Its only matter of two connection belts and thats all at all .
Screen replacement is really easy here.
Click to expand...
Click to collapse
how did you put the keyboard back on????????????????
Can you be more specific?
Hey,
I literally just replaced the screen on my backup Tilt last night. Still got most of it in my head.
What, exactly, do you mean about putting the keyboard back on? Got any pics of where you are now?
This was one of the easiest things I've had to do...asside from it being somewhat tedious. Most of my issues were resolved by MAGNIFICATION! Once I could see what I was doing, there were almost no issues.
I only paid $31.99 on eBay for a screen with free shipping (from USA no less)...less than the $35 I would have had to pay with the insurance through my Provider Dealer...and I didn't have to wait for 3-5 weeks to get it back.
I'd do this for people with broken screens as a service, but I can't guarantee the cost of the screen...it goes up and down too much.
If you can be real descriptive, or have pictures, I'm pretty sure I can help get you back together.
Let me know, I'll keep an eye on this thread...
RAF
here's some dismantling guides
http://www.mikechannon.net/page1.html
you dont have to remove the keyboard to replace the LCD, unless u're talking about the outer keypad, which just sits in its spot
My touch screen stopped working on my phone, but the screen is still visible. I'm assuming it's the digitizer. I was wondering if anybody has done or tried replacing only the digitizer. Does this work, is it better just to replace both? Any suggestions? Thanks.
Save yourself the headache
Just replace the complete screen unit (lcd + digitizer).
The digitizer is held on the screen with some super strong adhesive that is nearly impossible to get off cleanly. Also, there are three (4?) thin ribbon tabs that have to be soldered to the board on the rear of the lcd. Unless you are really confident with a soldering iron, it is extremely hard to do.
I replaced my screen unit in about a half hour. Make sure you go to the wiki and find one of the excellent disassembly guides before you start.
Thanks
Thanks, that's exactly the information i needed to know. I found the fon logix video. Is it only a t6 tool i need, or do i also need a t5. I have seen conflicting info on this? Thanks again.
I got my scren unit from ebay, and it included a torx driver and a plastic case tool. I honestly can't remember what size came in the kit, because I used my own torx set. Im pretty sure its just the one size, though.
Good luck!
You might find this information interesting.
http://forums.wireless.att.com/cng/board/message?board.id=cingular&thread.id=116836
Disregard ............
i always replace only the touch screen. okay i've done it aprox 30 times. But i never broke one.
if you decide to replace only the touchscreen, there are 2 types. thus check which on you have, and i found out that sometimes reassamble, and cleaning can help.
good luck.
torx is 5 and 6, 6 for opening the back of the phone, 5 for the screen part removal of the body and opening it. you need an opening tool!!
adhesive
is there a terrible adhesive between the screen and digitizer, as the second poster mentioned? how difficult is it to deal with?
just cut away with snapoff knives. It wil break in more pieses. (the glas that is) just be carefull, and take your time
Thanks
Thanks for all of the info, i went ahead and purchased the screen with the digitizer and tools. One thing i have noticed though is the d-pad has stopped working also, i'm using a custom rom so i'm not sure if it's just that or it's something else. i will prob re-image after i replace screen.
Abel2007 said:
just cut away with snapoff knives. It wil break in more pieses. (the glas that is) just be carefull, and take your time
Click to expand...
Click to collapse
Well, guess I was a smarty pants and bought my stuff before consulting XDA...as such, I ONLY bought the touchscreen rather than the entire new unit. Cheaper, yes, but I had no idea about the adhesive until just now. My only question is, once I remove the old screen from the LCD with a razor blade, how do I affix the new one?
Anyone?
i would love to know this too because i have to also replace my digitizer!
drokkon said:
Well, guess I was a smarty pants and bought my stuff before consulting XDA...as such, I ONLY bought the touchscreen rather than the entire new unit. Cheaper, yes, but I had no idea about the adhesive until just now. My only question is, once I remove the old screen from the LCD with a razor blade, how do I affix the new one?
Anyone?
Click to expand...
Click to collapse
I used rtv gasket maker the transparent blue one worked well.
you can find it in automotive section. Actually any silcone will work.
also can use double sided tape but needs to be very thin
I've already changing my digitizer, but it doesn't seem to work. So I've change the whole part. cost me $20 more on ebay.
my advice is to change the whole package with the lcd too.
is this housing http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=260453968402&ssPageName=ADME:X:RTQ:US:1123 a FURTHER rip-off in quality as the OEM found here http://cgi.ebay.com/OEM-SONY-ERICSS...ries?hash=item2ea6dd8d1e&_trksid=p3286.c0.m14
i want to buy a new housing but i don't wanna buy one with less quality than the original
what are your thoughts on the pics there?
Judging by the pics both fascias seem identical. Although don't know why this big pricing difference. Maybe the first auction is for a replica housing? Don't have large pics as the second auction so we can tell for sure.
Also, at CNN http://cnn.cn/shop/sonyericsson-xperia-c-28_638.html the housings are pricey. For me go for the second auction or buy from CNN, you will be 100% sure that the housing is the OEM.
yeah i was looking at the $24.00 on ebay too... someone should buy it and tell me how it is
i think im gonna let this pass and sell my x1 as it is, im thinking of leaning towards the touch diamond 2 i will miss my keyboard but what the heck
Yo!
I ordered the $24.00 last week... When I receive the housing parts, I will take pictures and spread the message....
Fingers crossed......
Damn the cracks....Its a pity to sacrifice a gd device just now that some gd new things are coming....senseUI....Leo...sure it'll come for d2 too.....but no KeyBoard there.....I have ur very same problem...but I'll try the case !!
Received the housings yesterday.
They're certainly not OEM (maybe the backcover is, the rest not). The outside looks quite nice finished, the set is quite complete (with some tools for the fitting). From the two sets I ordered, one has a large gluestain on the top part of the housing (below the LCD). This gluestain damaged the paint. So I decided to start transferring the phone in the other housing.
After dissecting the phone I started with the assembly of the screen part. The speaker fitted not quite nice, so took some feddling to get mounted. At last it fitted (the print on top of the speaker fitted just). Closing the top part of the housing was a mess. The snap-locks didn't snap (partly) and on one side the housing did not flush fit. The (original) screws did not fit in the thread bushings.... With some fiddling I sort of managed to fit them. Then on with the bottom part. The new chrome buttons do not fit in the new chrome housing part.......
This is were I give up for yesterday. I think I'm going to rebuild the old housing en give up on the new one....
So.....
Decide for yourself if it's worth the trouble.... The housing looks quit neat (not as good as OEM though) but the fitment process is quite troublesome. Delivery was fast and the package is complete (including self-adhesive rubber for screen and speaker fitment). I will get in touch with the guy from Ebay with my findings.... Maybe I'm doing something wrong....
Will post some pictures tomorrow or something....
thnx ur comments were of gr8 benefit to me.....will be gladly w8ing for the pics !
thnx, ur comment were of gr8 benefit to me.....will be gladly w8ing for the pics !
thnx dude, im waiting on mine to be delivered,
looking forward for more reactions...
@Fliptil
From a scale from 0-10, how hard was it to do?
Before starting myself, I want to know if i'm capable of doing this.
To be honest, I know how to fix stuff, but don't know if I can do this trick..
Thanks for sharing anyway
Does anybody know, where i can buy a non branded battery cover for my sliver x1?
It is branded with T-Mobile, but i would like to have it blank or non-branded.
An original one is 25 € in ebay Germany. That's too much. So a cheap one would be fine.
Thanks in advice for all tips!
Best regards
Jog
ebay dude, i purchased one 2 weeks ago for about 10 GBP
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=170363212269
OK guys....
I managed to revive the Xperia tonight.... It has become a hybrid with the metal (original) front and black backside. The middle part is also left original. So the only part I ended up exchanging has been the back cover.
First of all; kudo's to HTC for making the Xperia somewhat sturdy (at least the inside is...). The amount of mechanical havoc tha has been put through the innards of the phone are substantial... And still everything functions!!
After the initial assembly attempt a few weeks ago, I was sure that I had wrecked my phone trying to assemble it with the new housing. Some parts did not fit really well, and the (original) screws did not quite fit the (new) threaded bushings. Halfway through the assembly process I ran into the new chrome buttons not fitting in the new chrome middle part and I gave up on assembly for the time being. After recharging myself for a couple of weeks I forced myself to take up the task of finishing the assembly of the phone tonight...
First I had to disassemble the phone (I was halfway assembling it...) again. I decided to use the original front (had some scratch damage and a very small crack) to surpass the not-fitting thread bushings in the new part. This was a problem... One of the screws had settled in the not-fitting thread bushing and decided to not unscrew, but turn the bushing in the plastic instead. After trying careful and not damaging anything for some time I decided it was time for the hobby knife and screwdriver (as crowbar...). The new front cover did not survive this operation. The screw and the innards of the phone did however!! Reassembly using the old front cover was quite easy, as was reassembly of the back using the original middle part. In the new back part was the thread bushing missing for fixation of the speaker... I used the not-fitting bushing from the front cover as bushing for the speaker fixation. Off course after I made the bushing fitting by forcing the screw in the bushing using a sturdy screwdriver and a set of pliers. This bushing was hammered (carefully...) into the location where the bushing should have been.... This sort of worked. The new back cover does not fit as neat into the original middle part as the original back cover, but it did fit (with some force). The plastic lip that fixes the SIM card was a bit to long, so I had to cut of 0,5mm to make it fit the SIM card. And last but not least only one of the two new battery covers was able to get a grip on the phone...
Then came the thrilling moment to switch on the phone.... Everything worked as if nothing had happened!! So end good all good; I have a phone that looks quite neat (part brushed metal - part black) and functions.
If it was worth the hassle... I doubt it... When you've got a phone that is in pieces and you want spare parts to repair it (as cheap as possible and you like some hobbying) then go ahead and buy this housing. If you want a phone that looks as good as new (and you don't want to risk a heart attack or nervous break down) then I guess you're better off leaving this housing as it is.... For a phone that's worth a few hundred bucks I think this housing is not OK. For a scrapheap phone that needs revitalisation for a small amount of money than it's OK.... If I had to do it all again I think I would have gone for an OEM housing.... After all, I'm happy that my phone functions again so I can leave the TYTN at home. I was to stubborn to buy another housing...
This has become quite a story, hope it will be of any help to somebody. Now I must see if I can post some images....
Grreetz,
Ronald
Some pictures.... try if it works....
Hmm i've dropped my poor x1 on the concrete sidewalk as i got out of my car.
Amazingly it must be good quality because there are a only a couple of scratches on the front and some damage on the rubber around where the
stylus is, but otherwise everything works and is functional.
What this experience did, was got me lookin for spare parts in case I'd
ever need them. As a result I ordered from the same person on eBay 2 days ago
and I just now found this post. Needless to say, I'm damn scared that I've
wasted the money. You tried to fit the black parts on a silver X1, and mine is black,
so I'm crossing my fingers that for some unknown odd fantastical reason, it fits better on the black version. Also may ask whether your model is an x1i or x1a?
I'm guessing b/c its silver its an x1i but u can nvr be to sure. As for me, mine is
a black x1a. I'll post back if i have any updates.
Hi Nick.
I've got a X1i, as you had already guessed.... The mixing of the parts is also a bit of a risk.... The chrome middle part (original) has suffered some damages during my disassembly actions to start with... And has developed some new cracks in the use as a hybrid. Maybe I've overtightened some screws, or maybe the bottom part does not fit well enough so it develops to much tension I don't know...
I've decided to use the X1 till it dies, and to buy something else (no slide keyboard) a little bit more sturdy when it does. I am not going to do any repairwork on it. The design is simply flawed, I have had it repaired at SE once, when it came back it was broken again within two months. These stories can be found al over the internet, so I am not going to repair it again (just to get it broken again). I am not careful enough for a phone like this (however, my colleague also has a X1 that's broken and he is very careful...) I guess.
Just my two cents.
thanks fliptil I'll keep those things in mind.
Before i dropped my x1 for the first time. There was some kind of defect in the silver middle part. At first it was a slight crack so i thought nothing of it, until a piece fell right out of it. Until now i've never needed to go through the process
of getting something fixed and was my experience painful. I got mine through a carrier (Rogers) so I called them on the phone. I was on hold forever, and when I finally got through they told me I had to go to a rogers store to have someone
personally take a look at it.
I got to the store, got on their phone, and was on hold for 20 minutes. When I got through they told me they would connect me to a specific department.
Another 20 minute wait.
I got through and then gave the phone to a rogers employee there. He confirmed that it should be a defect as there were no signs of dropping it and then HE waited 20 minutes while the guy on the line called sony.
I waited all that time to find out that I cannot get it replaced through my carrier but had to go through sony themselves.
I looked up some stories of experiences with SE's services and found that most (if not all) of the time they replace your x1 with a refurbished one, and I wasn't about to trade a perfectly brand new one with a minor ding in it, for
one that could be potentially scratched up and badly treated.
Now that I've dropped it though I fear that whether the defect gets worse or not I cannot get Sony's warranty on it. However, after what you've just told me I don't think I want to. Here's to hoping that i won't have to do x1
surgery anytime soon...
Yes, I already broke my phone. Go ahead, grin and chuckle..now that you've gotten it out of your system, anyone want to offer a little guidance? Never disassembled a newer cellphone before. New glass is ordered and has been shipped, just waiting for it to arrive. I'm hoping the process is fairly simple. I do have a specialized set of screwdrivers with all the hard-to-find bits, so that's not a problem ..it even has the tiny blackberry bit.. but from what I can see HTC uses standard micro Philips screws. Yay for standard formats!
Sent from my HTC PH39100 using xda premium
If this phone is anything like hd2 you're gunna want the flat pry tools they sell (search hd2 screen replacement tools). Their not needed but a nice handy thingy to have, other wise you might crack your LCD from flexing it too much.
Sent from my HTC PH39100 using XDA App
I wont grin and chuckle too much, I broke my Atrix after 4 days.
The Vivid screen seems very fragile. 2 of my coworkers have broken theirs within a few weeks of having them. Small drops from waist distance. Its too bad because I have seen the current Samsung models dropped from 6 feet face first and survive
Sent from my HTC PH39100 using xda premium
Yeah, I've cracked mine as well. If you google HTC raider teardown on YouTube.. There's a vid.... Butttt, it's not in English and it's a teardown not a screen replacement tutorial.
It seems as thought HTC has been using reeeeally thin glass in their devices.
Whered you get the glass? It'd be very thoughtful of you to do a tutorial as you do it. I really want to replacement mine but if you remove one on the screws by the battery it voids your warranty
Send it to HTC then? You get a 1 year warranty when you buy the phone.
Honestly, I think Corning had another incident of releasing faulty glass. I've dropped mine numerous times, from pretty high up and I don't have a single scratch on my phone.
travisxcore said:
Send it to HTC then? You get a 1 year warranty when you buy the phone.
Honestly, I think Corning had another incident of releasing faulty glass. I've dropped mine numerous times, from pretty high up and I don't have a single scratch on my phone.
Click to expand...
Click to collapse
How much is it for them to fix it?
I have no idea. Shoot them an email (not Support Inquiry, youre gonna wanna send it to Repair Inquiry) and they should be able to tell you. Make sure you fill out the S/N box out now, or their just gonna send you an email back asking for it.
travisxcore said:
I have no idea. Shoot them an email (not Support Inquiry, youre gonna wanna send it to Repair Inquiry) and they should be able to tell you. Make sure you fill out the S/N box out now, or their just gonna send you an email back asking for it.
Click to expand...
Click to collapse
I'll do that right now. Thanks alot
(sorry to hijack the thread lol)
They use a double sided tape that hopefully comes with your replacement screen , I tried to replace a water damaged screen and it really wasn't a fun process
Sent from my HTC PH39100 using xda premium
It didn't fall very far..
Yeah when mine fell I had it in a shirt pocket, bent over to pick something up and it slid out, fell about a foot and a half..directly onto the search button corner on ceramic tile. Crunch. I ordered a new panel from tmart.com .. I got a confirmation email back on the 4th saying its been shipped via usps.. should be here soon. I hope it comes with everything I need - cost me about $50.00 with the shipping and everything. I paid the extra 3 bucks for insurance lol..
bproulx said:
Yeah when mine fell I had it in a shirt pocket, bent over to pick something up and it slid out, fell about a foot and a half..directly onto the search button corner on ceramic tile. Crunch. I ordered a new panel from tmart.com .. I got a confirmation email back on the 4th saying its been shipped via usps.. should be here soon. I hope it comes with everything I need - cost me about $50.00 with the shipping and everything. I paid the extra 3 bucks for insurance lol..
Click to expand...
Click to collapse
So, how was the installation process? And did it come with the adhesive? I'm going to buy it from that site as well
And then it was fixed..! FTW!
Ok sorry for the delay getting back to you guys.. been frantically waiting for the screen to clear US customs (ugh) and arrive, which it finally did today. I was able to get my hands on it at about 3 this afternoon, but I wasn't able to actually look at it until about an hour ago..
So.. I open the package, big grin on my face..and the first thing I notice is that the glass is AT&T branded. Funny, considering I'm in Canada and using Rogers..but hey a digitizer by any other name...and all that. So! I open the bag that my "tools" came in.. There are 2 blue plastic tools, one a prying tool and one looked a lot like a guitar pick. Cool. There are also 2 screwdrivers included, and I'm momentarily excited, until I realize they're just tiny torqx bits. The Raider uses TINY philips head screws, so those were useless. I put them into my tiny tool set..for later consideration.
Back to the screen. Looks like it the real deal, so I watch half of the teardown vid on youtube.. As mentioned in an earlier post it isn't an english-language vid so aside from seeing the locations of the screws and the methods of levering off the internal components, there's no exchange of information going on. I would like to mention however that the video kind of glazes over the locations and removal processes for some sensitive connections, so having only experienced laptop repairs personally.. I was in fairly uncomfortable and unfamiliar territory - but I was determined.
I tried several ways at getting the phone down to its base components, and finally succeeded in locating the panel's ribbon connector interface on one of the phone's circuit boards. I had to remove the back of the phone, pull the batt, sim and sd, and pull the 4 main screws that lock the housing down onto the phone.. From there its a matter of levering off the black plastic shell and whats underneath is a whole lot of tech in a very tight space. There were 3 or 4 wires I had to disconnect, about 15 tiny screws in 3 different lengths, and then when all was said and done I had to pry the busted panel off using the supplied blue lever tool (pretty handy, actually.) and then lift the lcd away from the metal housing enough to slide the old connector out and the new one through.. This was a very tricky process - I drink way too much coffee to hold completely steady for long..lol.. Finally got it all through, but by this time I had smudged the inside of both glass surfaces pretty badly and it took some serious mechanical dexterity to hold the surfaces and wipe them down without wrecking any of the flapping, loose circuit boards, screens, etc.. it was a frightening experience.. I won't lie.. I definitely feared the worst possible outcome given my limited experience.
So.. the panel's ribbon cable is inserted, the white clip back down securing it.. I manage after several attempts to remember how to put the puzzle all back together, and after about 45 minutes of messing with it I had a visually complete phone again. I hit power, and miracle of miracles the HTC logo flashes on the screen.. I'm hopeful..
The phone boots up, looks great (aside from a few smudges I missed on the inside..grr) so I start touching the screen and here's where we have the first problem..lol.. its recognizing that I'm touching the screen..but not really accurately.. it seems to be that there are dead areas.. So now I'm thinking I broke something..lol..
Smoke break.
Took it all apart again, forgot to clean the smudges, removed and re-seated all the connections, and about 15 minutes later I had it back together again. I booted it up and waited.
Success!! It sees where I'm touching accurately now - I think the ribbon must have moved while I was putting it back together, I was shifting things a lot as I was trying to figure it all out, so I must have stressed the cable enough to move it slightly in the slot.. that, or I didn't have it all the way in / straight the first time I did it. Either way, it works fine now. I was successful on the 2nd attempt, and now the only difference is that this glass feels..rougher? less smooth? not sure how to describe it.. it feels different, anyway.. and the at&t logo of course. Aside from that, you'd never know it was in pieces an hour ago..lol.
Would I do this again? ..I hope I don't have to. Its not impossible, but man, if you're going to try this BE SUPER CAREFUL!! lol..
edit: and no - it didn't come with the double sided tape, but it seems to be staying without having to replace it.. it wasn't too hard to remove it from the panel, but getting it back on straight took some finesse.. lol.. it comes apart easier now when you're tryingn to disassemble it..but seems to be holding together fine on its own.
travisxcore said:
Send it to HTC then? You get a 1 year warranty when you buy the phone.
Honestly, I think Corning had another incident of releasing faulty glass. I've dropped mine numerous times, from pretty high up and I don't have a single scratch on my phone.
Click to expand...
Click to collapse
Corning makes the glass on the Raider/Vivid?
I would suspect it to be more sturdy if its corning, my SGS has been without a screen protector and still does not have any scratches. Yes i know SGS is Gorilla Glass and this is not but i would think it would be stronger.
@ bproulx
You should take it apart again and make a tutorial . I hope i never have to go though what you did. Knock on wood.
lol..might take it apart again..
So..I have smudges on the inside of the glass. Stupid sweaty fingers. Now I'm tempted to pull it apart again ..but not far enough to make a tutorial lol.. besides.. I'm glad I didn't have a camera on me - you guys woulda had a good laugh at me breaking into a sweat trying to pry loose the glass panel the first time..lol. I know it was already broken but (a) I was trying not to cut myself on it and (b) I was also trying not to break the lcd underneath. Which I believe also has smudges on it. Oi.. I guess I'll have to get in there and clean it. Probably not tonight tho. I'm just glad the thing still works - I was scared I was going to bust something. There are a LOT of little things in there. For the record the CPU looks neat. Its smaller than a sim card, a little bigger than a micro sd. Pretty impressive.
bproulx said:
So..I have smudges on the inside of the glass. Stupid sweaty fingers. Now I'm tempted to pull it apart again ..but not far enough to make a tutorial lol.. besides.. I'm glad I didn't have a camera on me - you guys woulda had a good laugh at me breaking into a sweat trying to pry loose the glass panel the first time..lol. I know it was already broken but (a) I was trying not to cut myself on it and (b) I was also trying not to break the lcd underneath. Which I believe also has smudges on it. Oi.. I guess I'll have to get in there and clean it. Probably not tonight tho. I'm just glad the thing still works - I was scared I was going to bust something. There are a LOT of little things in there. For the record the CPU looks neat. Its smaller than a sim card, a little bigger than a micro sd. Pretty impressive.
Click to expand...
Click to collapse
I've taken apart laptops (MacBooks at all) and successfully reassembled them so I think I'm up to the job. I'm reaaaally thankful that it says AT&T at the top and not HTC like the pic shows (since I'm on att).. Another question though, did you successfully get the "void" plastic piece back over the screw? Because, I want to keep this phone as "under warranty" as possible
Getting better at taking it apart..lol..
Chism87 said:
I've taken apart laptops (MacBooks at all) and successfully reassembled them so I think I'm up to the job. I'm reaaaally thankful that it says AT&T at the top and not HTC like the pic shows (since I'm on att).. Another question though, did you successfully get the "void" plastic piece back over the screw? Because, I want to keep this phone as "under warranty" as possible
Click to expand...
Click to collapse
No, the little void sticker on mine was less like a sticker and more like... glue, with paint on it.. lol.. it just flaked apart when I tried to lift it.. but I wasn't concerned with preserving it. Maybe if u use an x-acto or something like that you can lift it intact..? Let me know how you do.
I started getting some random touch input glitches yesterday, and today they got worse.. then my son spilled hot coffee on me and I dropped my phone on the carpet where it of course popped apart..lol..and then when I booted it back up I had some *major* touch glitches.. it was seeing input higher up than the actual contact point, and just acting real buggy..the phone was lagging.. so I took it apart again, completely.. took my sweet time reassembling it this time - I even got out the micro-fibre cloth and cleaned all the glass, and voila.. this time - its like new. I can already tell its put together right this time, which tells me something wasn't quite right before - I'm guessing I didn't get the ribbon cable seated properly before.. there are a lot of tiny, offset contacts on the end of that little cable. Anyway, I guess the moral of the story is screw warranties, and the more times you disassemble your phone the better you get at it.. lol.. it wasn't anywhere near as intimidating this time around. Felt kinda easy, actually. I think I just psyched myself into thinking it would be hard to do the first time around.
I do miss my original glass tho.. I'm thinking about contacting HTC and ordering an oem panel lol.. this one feels.. grippy. The HTC one felt smooth as silk.. I dunno this one kinda feels more like window glass. Meh.. better than a broken ghetto phone. At least now I can whip it out in public without hanging my head in shame and peeking around to see who's looking at my ugly screen. I never even tried HTC directly..I just googled the part and went with the one with good reviews..
OMFG...FML..
Sooo.. I got angry at my Raider today.. started doing the weird touch input glitches again after a battery pull, got frustrated and slammed my phone down on the table in anger...and.... smash. Brand new panel is now ten times as shattered as the old one was. AND...now the phone won't even light up. AND..it looks like I may have cracked the actual LCD this time.. just a small crack at the very bottom - wouldn't even be visible with the shell on the phone.. but.. I'm not very optimistic. I get absolutely nothing on my screen when I boot the phone, all I get is one haptic "bump" and thats it. Nada.
Sooo... looks like I need a new phone. Again.
Lame.
There goes $600.00
....sigh.
Anyone wanna donate an old android device to a guy who's now really really sad and has no phone? LOL.. why did I give away my legend????
Not giving up my phone!! LOL!
Ok so I decided to try my luck at replacing the LCD as well as the busted digitizer that I just re-broke..lol.. back to tmart, and ordered both. I really wish I could have found the whole assembly pre-built, but the only company I found selling both as a single unit had a minimum order of 5 pcs. Out of my price range for repairs, although with my track record maybe it wouldn't have been a bad idea? lol.. anyway, I just bought both parts from tmart and am still waiting for one of them to show up. The good news is I was able to replace the LCD already. It really is just held in there with tape. Like.. there's nothing really holding it all together..you'd think with all those screws and tabs they could have come up with a better way?? Ah well. I have a display again, but until I can get the digitizer and install it I'm without input.. so I can just watch the phone boot and then sit on my lock screen. Or boot into recovery mode and use the vol and power buttons to mess about.. But why..lol. I'll just wait.
I'm just happy that nothing else seems to be affected. I had my alarm going off still with no screen, so that tipped me off that everything else should still be ok. I won't know for 100% certain til I complete the repair, but it looks promising. I picked up a used HTC Magic (ugh) from kijiji for $80 and it came with 3 batteries, 3 chargers, 3 usb cables, 3 leather cases, and a bunch of other crap in threes. Just so I'm not completely without a phone in the meantime. Overall not bad for $80 but man is this phone slow. I installed a custom rom **THANKS XDA!!** on it and it improved the performance and look of the OS a little, but it lags a lot even overclocked when just typing a text.. I can't wait to get my phone back!!
Aside from the screens, this phone is pretty tough. I slammed that sucker down pretty hard that day.. Cmon HTC - why didn't you give us gorilla glass on a $600 LTE phone!?!?!?!? I wish I could find an aftermarket panel that was made from gorilla glass. That would totally rock!
Yeah, i really wish they would've put gorilla glass on it. I used to have the atrix and ive dropped it on tile floor at least 3 times... Nothing. Keys in the same pocket as phone.. No scratches at all.
I didn't want to try my luck, so I just got a replacement vivid