Related
I will soon be opening up my phone (T-mobile Pocket PC Phone Edition) to replace the glass screen with a new one ordered online. I've never even opened the phone before and was wondering if someone has performed this operation before. I would really appreciate any pointers, tricks, cautions, pictures, etc.
Thanks.
lawrence... where did u get the replacement??
i wonder if they got replacement cases! i chiped mine
The company I bought the screen from was GetHighTech, Inc, in California. By coincidence, they are about an hour's drive away from my home.
They only sell the glass screen and high capacity battery replacements. The screen comes with absolutely no documentation or instructions. I just got it a few minutes ago.
just wanted to see if you had any luck with the changeout.
Screen replaced successfully: observations
It was a tricky operation, but I finally managed to replace my broken touch screen. And the patient is alive, and only a little worse off for the experience.
I was held back for a week until I could get the right size torx screwdrivers to remove the back cover. Once inside, it was a very very tricky process slicing off the broken screen with a razor blade. It was glued to the lcd display. This would have been hard even if the screen was not shattered. Definitely needed goggles to protect against flying splinters of glass. I used cotton swabs and 99% alcohol to clean the glass dust off the glue around the edges of the lcd, then I put the new screen on while that residual gum was still a bit tacky.
There was a very thin existing plastic cover over the lcd in between the glass touch screen and the rest of the lcd. Since it did not come off with the glass, I left it in place even though it had a couple of small scratches from contact with the broken glass. It seems like it was there to keep dust off the lcd or something like that.
This was my first time inside the phone. I noticed that replacing the whole LCD component would have been a trivial task by comparision to replacing the glass alone. And even easier would have been adding a new battery.
cracked lcd on xda
hi, does anybody know where i can get a replacement for the lcd screen on my xda... its totally mashed and i need to unlock it but the screen is bad...
i live in uk... any ideas guys..
pls help out
has anyone give me pls an idea how much a new replacement screen for XDA might cost
currently I am having two XDA (one XDA and one MDA), MDA has a broken screen ... I'd like to know how much is the material (screen), I have so. to do the actual job of screen replacement
regards, monika
I replaced my touchscreen a few weeks ago. Like Lawrence said it's a little tricky and you need to be patient.
I bought my touchscreen from www.pdasmart.com/pdaphone.htm for $75 and they gave great instructions.
thank you for your kind answer
hmmm, seems like it is nice to live in US ... where all the things for XDA are almost readily available :wink:
regards, monika
Protective Acryclic Cover over the Digitizer
I have an odd problem. I have an SX56 with a broken protective cover. The protective cover is the acrylic sheet that sits between the digitizer and the outside world. Everything else works fine including the digitizer. I have found every replacement part except that cover. I've even tried local plastic stores. They don't carry the proper thickness (0.125mm).
Any thoughts or sources besides sending it in for a $200 repair?
is this housing http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=260453968402&ssPageName=ADME:X:RTQ:US:1123 a FURTHER rip-off in quality as the OEM found here http://cgi.ebay.com/OEM-SONY-ERICSS...ries?hash=item2ea6dd8d1e&_trksid=p3286.c0.m14
i want to buy a new housing but i don't wanna buy one with less quality than the original
what are your thoughts on the pics there?
Judging by the pics both fascias seem identical. Although don't know why this big pricing difference. Maybe the first auction is for a replica housing? Don't have large pics as the second auction so we can tell for sure.
Also, at CNN http://cnn.cn/shop/sonyericsson-xperia-c-28_638.html the housings are pricey. For me go for the second auction or buy from CNN, you will be 100% sure that the housing is the OEM.
yeah i was looking at the $24.00 on ebay too... someone should buy it and tell me how it is
i think im gonna let this pass and sell my x1 as it is, im thinking of leaning towards the touch diamond 2 i will miss my keyboard but what the heck
Yo!
I ordered the $24.00 last week... When I receive the housing parts, I will take pictures and spread the message....
Fingers crossed......
Damn the cracks....Its a pity to sacrifice a gd device just now that some gd new things are coming....senseUI....Leo...sure it'll come for d2 too.....but no KeyBoard there.....I have ur very same problem...but I'll try the case !!
Received the housings yesterday.
They're certainly not OEM (maybe the backcover is, the rest not). The outside looks quite nice finished, the set is quite complete (with some tools for the fitting). From the two sets I ordered, one has a large gluestain on the top part of the housing (below the LCD). This gluestain damaged the paint. So I decided to start transferring the phone in the other housing.
After dissecting the phone I started with the assembly of the screen part. The speaker fitted not quite nice, so took some feddling to get mounted. At last it fitted (the print on top of the speaker fitted just). Closing the top part of the housing was a mess. The snap-locks didn't snap (partly) and on one side the housing did not flush fit. The (original) screws did not fit in the thread bushings.... With some fiddling I sort of managed to fit them. Then on with the bottom part. The new chrome buttons do not fit in the new chrome housing part.......
This is were I give up for yesterday. I think I'm going to rebuild the old housing en give up on the new one....
So.....
Decide for yourself if it's worth the trouble.... The housing looks quit neat (not as good as OEM though) but the fitment process is quite troublesome. Delivery was fast and the package is complete (including self-adhesive rubber for screen and speaker fitment). I will get in touch with the guy from Ebay with my findings.... Maybe I'm doing something wrong....
Will post some pictures tomorrow or something....
thnx ur comments were of gr8 benefit to me.....will be gladly w8ing for the pics !
thnx, ur comment were of gr8 benefit to me.....will be gladly w8ing for the pics !
thnx dude, im waiting on mine to be delivered,
looking forward for more reactions...
@Fliptil
From a scale from 0-10, how hard was it to do?
Before starting myself, I want to know if i'm capable of doing this.
To be honest, I know how to fix stuff, but don't know if I can do this trick..
Thanks for sharing anyway
Does anybody know, where i can buy a non branded battery cover for my sliver x1?
It is branded with T-Mobile, but i would like to have it blank or non-branded.
An original one is 25 € in ebay Germany. That's too much. So a cheap one would be fine.
Thanks in advice for all tips!
Best regards
Jog
ebay dude, i purchased one 2 weeks ago for about 10 GBP
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=170363212269
OK guys....
I managed to revive the Xperia tonight.... It has become a hybrid with the metal (original) front and black backside. The middle part is also left original. So the only part I ended up exchanging has been the back cover.
First of all; kudo's to HTC for making the Xperia somewhat sturdy (at least the inside is...). The amount of mechanical havoc tha has been put through the innards of the phone are substantial... And still everything functions!!
After the initial assembly attempt a few weeks ago, I was sure that I had wrecked my phone trying to assemble it with the new housing. Some parts did not fit really well, and the (original) screws did not quite fit the (new) threaded bushings. Halfway through the assembly process I ran into the new chrome buttons not fitting in the new chrome middle part and I gave up on assembly for the time being. After recharging myself for a couple of weeks I forced myself to take up the task of finishing the assembly of the phone tonight...
First I had to disassemble the phone (I was halfway assembling it...) again. I decided to use the original front (had some scratch damage and a very small crack) to surpass the not-fitting thread bushings in the new part. This was a problem... One of the screws had settled in the not-fitting thread bushing and decided to not unscrew, but turn the bushing in the plastic instead. After trying careful and not damaging anything for some time I decided it was time for the hobby knife and screwdriver (as crowbar...). The new front cover did not survive this operation. The screw and the innards of the phone did however!! Reassembly using the old front cover was quite easy, as was reassembly of the back using the original middle part. In the new back part was the thread bushing missing for fixation of the speaker... I used the not-fitting bushing from the front cover as bushing for the speaker fixation. Off course after I made the bushing fitting by forcing the screw in the bushing using a sturdy screwdriver and a set of pliers. This bushing was hammered (carefully...) into the location where the bushing should have been.... This sort of worked. The new back cover does not fit as neat into the original middle part as the original back cover, but it did fit (with some force). The plastic lip that fixes the SIM card was a bit to long, so I had to cut of 0,5mm to make it fit the SIM card. And last but not least only one of the two new battery covers was able to get a grip on the phone...
Then came the thrilling moment to switch on the phone.... Everything worked as if nothing had happened!! So end good all good; I have a phone that looks quite neat (part brushed metal - part black) and functions.
If it was worth the hassle... I doubt it... When you've got a phone that is in pieces and you want spare parts to repair it (as cheap as possible and you like some hobbying) then go ahead and buy this housing. If you want a phone that looks as good as new (and you don't want to risk a heart attack or nervous break down) then I guess you're better off leaving this housing as it is.... For a phone that's worth a few hundred bucks I think this housing is not OK. For a scrapheap phone that needs revitalisation for a small amount of money than it's OK.... If I had to do it all again I think I would have gone for an OEM housing.... After all, I'm happy that my phone functions again so I can leave the TYTN at home. I was to stubborn to buy another housing...
This has become quite a story, hope it will be of any help to somebody. Now I must see if I can post some images....
Grreetz,
Ronald
Some pictures.... try if it works....
Hmm i've dropped my poor x1 on the concrete sidewalk as i got out of my car.
Amazingly it must be good quality because there are a only a couple of scratches on the front and some damage on the rubber around where the
stylus is, but otherwise everything works and is functional.
What this experience did, was got me lookin for spare parts in case I'd
ever need them. As a result I ordered from the same person on eBay 2 days ago
and I just now found this post. Needless to say, I'm damn scared that I've
wasted the money. You tried to fit the black parts on a silver X1, and mine is black,
so I'm crossing my fingers that for some unknown odd fantastical reason, it fits better on the black version. Also may ask whether your model is an x1i or x1a?
I'm guessing b/c its silver its an x1i but u can nvr be to sure. As for me, mine is
a black x1a. I'll post back if i have any updates.
Hi Nick.
I've got a X1i, as you had already guessed.... The mixing of the parts is also a bit of a risk.... The chrome middle part (original) has suffered some damages during my disassembly actions to start with... And has developed some new cracks in the use as a hybrid. Maybe I've overtightened some screws, or maybe the bottom part does not fit well enough so it develops to much tension I don't know...
I've decided to use the X1 till it dies, and to buy something else (no slide keyboard) a little bit more sturdy when it does. I am not going to do any repairwork on it. The design is simply flawed, I have had it repaired at SE once, when it came back it was broken again within two months. These stories can be found al over the internet, so I am not going to repair it again (just to get it broken again). I am not careful enough for a phone like this (however, my colleague also has a X1 that's broken and he is very careful...) I guess.
Just my two cents.
thanks fliptil I'll keep those things in mind.
Before i dropped my x1 for the first time. There was some kind of defect in the silver middle part. At first it was a slight crack so i thought nothing of it, until a piece fell right out of it. Until now i've never needed to go through the process
of getting something fixed and was my experience painful. I got mine through a carrier (Rogers) so I called them on the phone. I was on hold forever, and when I finally got through they told me I had to go to a rogers store to have someone
personally take a look at it.
I got to the store, got on their phone, and was on hold for 20 minutes. When I got through they told me they would connect me to a specific department.
Another 20 minute wait.
I got through and then gave the phone to a rogers employee there. He confirmed that it should be a defect as there were no signs of dropping it and then HE waited 20 minutes while the guy on the line called sony.
I waited all that time to find out that I cannot get it replaced through my carrier but had to go through sony themselves.
I looked up some stories of experiences with SE's services and found that most (if not all) of the time they replace your x1 with a refurbished one, and I wasn't about to trade a perfectly brand new one with a minor ding in it, for
one that could be potentially scratched up and badly treated.
Now that I've dropped it though I fear that whether the defect gets worse or not I cannot get Sony's warranty on it. However, after what you've just told me I don't think I want to. Here's to hoping that i won't have to do x1
surgery anytime soon...
The inevitable has happened and I dropped my HD2 and now the glass is smashed into pieces.. the touch screen still works and the lcd looks fine underneath. A couple of questions;
Wheres the best place to buy the replacement parts?
Do I need to just replace the glass or the whole screen?
Is it a difficult job to replace it? the iphone was a bugger to do.
Hi,
I have got the same problem, always carefull and than in a split second it slips out of your hand. With me the "touch" still functioned but the glass was shattered.
I called HTC (in Holland), they have a service center where they can repair it and get full warranty back. It is a very expensive joke (I got a quotation of 267,50 Euro).
I could have my HD repaired by a non-htc company, but they did not give any guarantees. Prices were the same...
I heard that it is possible to only replace the glass, but almost always the digitizer is also (partly) defect. And if not then the chance of braking the digitizer is very big when you try to seperate it from the glass.
I had a lot of calls with my insurance company (no phone insurance) and finally they agreed to pay for the damages.
I hope this helpes a bit, good luck
Regards
Bazzz
how about a broken camera glass, does anyone know how much that costs?
yes
mine broke to and i would repari it
but im wondering to repair it alone becouse there are alot of glass lenses on ebay for like 5 us !
Think you can pick 1 up for about 50bucks..
Check --»Here«-- and --»Here«-- for detailed disassembling and assembling your Hd2..
A few days ago I cracked the glass screen on my Dinc. There wasn't any significant damage aside from the crack, and my LCD screen is working fine, so I ordered a replacement on Amazon thinking I could replace it. I found a screen which reviewers claimed came with the tools necessary to replace the screens, although the product did not advertise it as such. I made the order to find that the replacement did not come with any tools, and now I am stumped. Does anyone know where I can find cheap (and usable) tools to crack open my Dinc? I was hoping to finish this before I return to college in a few weeks and I'd rather not go back with a broken screen.
Thanks in advance!
Not sure what "tools" you're looking for, but there are only a few things you need to take your dinc apart (I just did this with mine):
1. T6 screwdriver to remove 4 screws on the big red cover
2. A small flat-head screwdriver to release block clips around the big red housing and pop it off. (also used to open up the ribbon cable clips)
3. small philips-head screwdriver to remove screws securing the main board and LCD
4. X-acto knife + hairdryer to remove the digitizer (the glass that you cracked)
Do yourself a favor and order the digitizer with the frame. It eliminates the need to pry the broken glass out completely. It is a little more expensive, I think I paid $35 for mine, but well worth the time and effort! All in all it took me about an hour to complete mine! BTW, I found and ordered all the parts and tools from amazon.
Sounds like you cracked the digitizer yet you ordered a new screen?
m52 power! said:
Sounds like you cracked the digitizer yet you ordered a new screen?
Click to expand...
Click to collapse
Although the sentence structure is somewhat ambiguous, it sounds like he bought the correct replacement part, a digitizer.
swatmedic911 said:
Do yourself a favor and order the digitizer with the frame. It eliminates the need to pry the broken glass out completely. It is a little more expensive, I think I paid $35 for mine, but well worth the time and effort! All in all it took me about an hour to complete mine! BTW, I found and ordered all the parts and tools from amazon.
Click to expand...
Click to collapse
I'll vouch for this, it's the biggest headache to replace JUST the glass.
Since you already got the glass, you can go ahead and order a bezel by itself if you want... make sure you get one that has adhesive on the metal lip on the inside so the dust won't get in there
swatmedic911 said:
Do yourself a favor and order the digitizer with the frame. It eliminates the need to pry the broken glass out completely. It is a little more expensive, I think I paid $35 for mine, but well worth the time and effort! All in all it took me about an hour to complete mine! BTW, I found and ordered all the parts and tools from amazon.
Click to expand...
Click to collapse
Exactly. I made the mistake of ordering JUST the screen and it was a complete headache. I subsequently ordered the frame/screen combo. Much easier.
Sent from my ADR6300 using XDA App
yeah i replaced mine but now i have trouble with the touch screen not working right. It randomly registers touches on the screen. Hope you don't run in to the same issue.
Glad to hear people are having success replacing these. I have a friend who's cracked his recently and will pass this thread on to him.
I replaced my screen with the digitizer/screen combo bought on amazon for under $20. it's a pain to install, but I found a good video on youtube and used their blowdryer method to make the glue more easy to manage and allow the screen to come off in fewer pieces. Also when you put the little ribbons back into their connectors make sure you get them all the way in - I had 256 color-like graphics for a little bit until I reconnected the screen properly
I've done it multiple times. I'm not clumsy, I just got the phone broken in the first place .
While it would make it easier to get the bezel, it can be done fine with just the digitizer.
They give you all the little plastic tools you need usually.
The last time I did it I used Krazy glue instead of very thin double sided tape.
I can answer any specific questions you have when replacing the digitizer if you want.
One request I have for you:
When I put the trackball back into place I wasn't sure if I did the correct order. It still works but it looks a little more recessed then it should be. Not a big deal, but it annoys me a tiny bit that my phone isn't perfect.
Could you record the exact order in which you disassemble it? It might even help you out later
drizzt5;19538891
One request I have for you:
When I put the trackball back into place I wasn't sure if I did the correct order. It still works but it looks a little more recessed then it should be. Not a big deal said:
I just replaced my screen tonight with an amazon digitizer kit and my trackball is also recessed. Might just open it back up and jam some leftover adhesive underneath it. I would recommend buying the frame though as it was a bit of a b*tch prying broken glass shards and adhesive from the thing. Would also make the phone look better as well..
Click to expand...
Click to collapse
i dont have a cracked screen but a very banged up bezel and battery cover. i calculated it and everything will cost me a total of $35 to replace. this includes the digitizer, bezel, battery cover and camera lens. cant wait to get this done.
thanks for the info on here.
Order the digitizer WITH the housing shell. I cracked my screen, too, and ordered the digitizer/screen only and ended up damaging my housing shell. The hairdryer trick is bogus and doesn't work very well, so spend the extra $10 to get the housing.
I was going to repare the screen to resell on Ebay, but since I broke the housing, I decided to just sell the actual AMOLED screen for $40. I'll find other parts I can sell, too, such as the motherboard and camera piece. Might actually end up making more money. Ah well.
I don't use Verizon anymore, which is why I ditched the DInc. Will miss it though. I do love HTC Sense. I have a Samsung Exhibit II now.
My first time doing this was with the digitizer only. Biggest mistake of my life! I could've made it work, but I was getting it replaced since it was bricked and superglue oozing out the sides might have raised some eyebrows. Digitizer+frame, void sticker, and 2 weeks later I had a "new" dinc.
Hi all!
I bought a HTC One M7 with a cracked screen dirt cheap from a friend and am hoping to repair it myself and I've had a look around the q&a forums but anyone that references to genuine or "OG" HTC parts doesn't specify where you can actually order them from, I'd be looking for both speakers, lcd screen, digitizer and front speaker covers but am pretty unsure of which parts are actually legitimate on the internet.
Any help guys?
TIA
Beans
bbeanss said:
Hi all!
I bought a HTC One M7 with a cracked screen dirt cheap from a friend and am hoping to repair it myself and I've had a look around the q&a forums but anyone that references to genuine or "OG" HTC parts doesn't specify where you can actually order them from, I'd be looking for both speakers, lcd screen, digitizer and front speaker covers but am pretty unsure of which parts are actually legitimate on the internet.
Any help guys?
TIA
Beans
Click to expand...
Click to collapse
Screen repair here, fairly cheap and apparently 100% genuine, saves you a lot of hassle, i.e, breaking it apart and re-sealing it, plus the possibility of damaging other parts, also ring them and ask if they can replace the other parts for you.
http://www.ebay.co.uk/itm/Repair-Re...410?pt=LH_DefaultDomain_3&hash=item19f93950c2
if not then the speakers are here, cheap as chips, you could always ask the LCD company, if you send the speakers with the phone, if they wouldn't mind changing them at the same time, it would take them 2 mins whilst they have it apart.
http://www.ebay.co.uk/sch/i.html?_f...m7+speakers&_nkw=htc+one+m7+speakers&_sacat=0
for the covers, depends on colour, but heres an idea:
http://www.ebay.co.uk/itm/New-Top-F...sPouches&var=460531438066&hash=item2594a951a1
All for less than £100, cant really beat that for the whole front end of the phone.
If you are going to replace the screen might I suggest you order an entire front housing with digitizer and screen and back housing. You will destroy your phones body when you open it. Order those parts and follow the complete breakdown and reassembly videos on YouTube. They are all good.
Is it hard to change just back cover?
bosas200 said:
Is it hard to change just back cover?
Click to expand...
Click to collapse
Personally I wouldn't take the risk of opening it all up myself, inside is extremely fragile and the motherboard connections for instance is as easy to rip in half as a piece of cloth, I destroyed a HTC Desire HD whilst trying to change the LCD and Digitalizer and the back of that was screwed on, the HTC One series is 10 times harder to open up.
Check this out for an idea of what is involved: https://www.youtube.com/watch?v=jVUAr5hLiEE