Related
Please help, I was uninstalling some applications from my HTC PURE and had to restart the phone, when it was rebooting it hung at the ATT screen and there was small red text in the bottom left screen.
I had previously installed HardSPL 1.83 but relocked it via instructions in 2nd post because I'm still deciding if I wanna keep the phone and didn't wanna do anything for warrenty reasons.
I have the stock ROM and never installed anything except the HardSPL and the revert.
Please help me, I have tried to load the ATT Pure Stock/Shipped ROM I found here but everytime I try to in the bootloader mode it says either "no image file" or hangs at loading depending what I've tried to name the file. Also I've tried to run customruu.exe to install the stock ROM and also tried to install HardSPL 1.83 but it hangs at 0% and eventually wants to do recovery on the PC.
How do I fix this problem, and preferabbly get it back stock. I do have a warrenty, well unless I violated it by installing HardSPL then doing the revert.
Thanks
viper2g1 said:
Please help, I was uninstalling some applications from my HTC PURE and had to restart the phone, when it was rebooting it hung at the ATT screen and there was small red text in the bottom left screen.
I had previously installed HardSPL 1.83 but relocked it via instructions in 2nd post because I'm still deciding if I wanna keep the phone and didn't wanna do anything for warrenty reasons.
I have the stock ROM and never installed anything except the HardSPL and the revert.
Please help me, I have tried to load the ATT Pure Stock/Shipped ROM I found here but everytime I try to in the bootloader mode it says either "no image file" or hangs at loading depending what I've tried to name the file. Also I've tried to run customruu.exe to install the stock ROM and also tried to install HardSPL 1.83 but it hangs at 0% and eventually wants to do recovery on the PC.
How do I fix this problem, and preferabbly get it back stock. I do have a warrenty, well unless I violated it by installing HardSPL then doing the revert.
Thanks
Click to expand...
Click to collapse
Of course you hard reset?
Make sure your SD card is formatted to Fat32 and you may mant to try a different card, 2gb - 4gb.
What does your SPL say now in bootloader mode?
Yes I tried a hard reset. I can try another sd card the one I used was fat32 and 2gb. I believe it says 1.33 can't look now but I know it's not the same as an untouched pure.
Help!
You are not the only one who is having this issue. I am frustrated beyond frustrated. How are other people flashing their out of the box ATT Pures using the same exact steps but I can't? It's making no sense.
1. I turn off firewalls.
2. I've tried both usb and sd card boot, didnt work
3. I installed the enablerapi cab
Nothing works and I am having the same problem you are having...it stays on 0% forever and it doesnt even prompt me saying there is an error it just sits on 0% until I unplug it...
Help!
themasterhook2000 said:
You are not the only one who is having this issue. I am frustrated beyond frustrated. How are other people flashing their out of the box ATT Pures using the same exact steps but I can't? It's making no sense.
1. I turn off firewalls.
2. I've tried both usb and sd card boot, didnt work
3. I installed the enablerapi cab
Nothing works and I am having the same problem you are having...it stays on 0% forever and it doesnt even prompt me saying there is an error it just sits on 0% until I unplug it...
Help!
Click to expand...
Click to collapse
Are you trying to HSPL or flash a ROM?
Well
According to what i've read, you have to do Hard SPL before you flash a rom, so i've been trying to HardSPL and it doesn't work! I even tried to skip the step and just flash the rom and it doesnt work..
Now, I also have an ATT Tilt to and I JUST flashed a rom 30 mins ago, so it has nothing to do with firewalls or anything as far as my computer goes, I think its the phone, so what can I do?
How to flash HSPL.
themasterhook2000 said:
According to what i've read, you have to do Hard SPL before you flash a rom, so i've been trying to HardSPL and it doesn't work! I even tried to skip the step and just flash the rom and it doesnt work..
Now, I also have an ATT Tilt to and I JUST flashed a rom 30 mins ago, so it has nothing to do with firewalls or anything as far as my computer goes, I think its the phone, so what can I do?
Click to expand...
Click to collapse
Its a good thing flashing the ROM didn't work, you'd be bricked.
For flashing HSPL, it seems that newer phones are having an issue.
Something may have been changed that is preventing the unlocker from working.
Do the following;
1. Hard Reset
Instructions:
- Soft reset with stylus
- Hold Vol up & Vol dwn simultaneously until white screen appears
- Following screen prompts, Press Vol up to confirm.
2. Go to bootloader mode.
Instructions:
- Turn off your device using the power button
- When the device is turned off, simultaneously press the Vol dwn + Power button
- Your device will startup in Bootloader mode
Should say SPL: 1.33 or something.
3. Sync your phone to your PC.
4. Install enablerapinew.cab
5. Unzip both Topaz_CustomRUU_v1.1.zip & SPL_183.zip to the same folder
6. Run the CustomRUU.exe
This process should install HSPL and now when you enter bootloader mode you should see something like SPL: 1.83 Olinex.
If so, you're ready to start flashing custom ROMs.
If not, please report all errors to the HSPL thread or PM Olipro.
**I take no responsibility for any loss of data or functionality of your device.**
See, the problem with your instructions are...
1. You cannot soft reset with the stylus, I don't see a button anywhere on the phone ( ATT PURE not Diamond 2 )
2. Holding Vol up & Vol down simultaneously until white screen appears doesn't work. The only thing that works is when I hold Vol Down and the screen with the colors come up, not a white screen.
So i'm still lost. Thanks for your help regardless. I just really want to flash a new rom so I can stop using this stupid slow ATT rom.
So basically you are messing with your Pure and don't know how to soft reset?
Remove the stylus and in the groove for the stylus is a red dot, that is the red reset button. Insert the tip of the stylus in the red dot and push. Now the Pure will soft reset.
Probably should familiarize yourself with the device before you finish turning it into a brick!
Oh wow. That is so hidden.
On my Touch Pro 2 its right there on the side where you can see it, with words.
Anyway, Thank you very much, i'll try that.
Still, what about the Up and Down button volume button function so I can go into bootloader mode?
themasterhook2000 said:
On my Touch Pro 2 its right there on the side where you can see it, with words.
Anyway, Thank you very much, i'll try that.
Still, what about the Up and Down button volume button function so I can go into bootloader mode?
Click to expand...
Click to collapse
Now that you found the soft reset button.... follow my procedures.
Note- you have to hold the keys IMMEDIATELY after soft reset before the boot screen appears.
Ok.
Bruce Inman said:
Now that you found the soft reset button.... follow my procedures.
Note- you have to hold the keys IMMEDIATELY after soft reset before the boot screen appears.
Click to expand...
Click to collapse
Didn't work, I re-did the steps you listed 3 times over to make sure I was correct and the same results. I guess ATT has found a way to stop their phones from being unlocked.
Thank you for your help regardless.
themasterhook2000 said:
Didn't work, I re-did the steps you listed 3 times over to make sure I was correct and the same results. I guess ATT has found a way to stop their phones from being unlocked.
Thank you for your help regardless.
Click to expand...
Click to collapse
You should probably post over in the HSPL thread.
You'll get more help over there. There are many others having similar issues and there may be a fix over there.
FYI, when you get to the tri colored screen, that is where it shows what SPL you have currently.
Updating rom freeze
Hi, I don't post much if at all, normally you guys have it right on the button, this is my 3rd phone to run custom roms on but for some reason it just freezes on the "Updating ROM image on your PDA Phone..." screen and doesn't continue past, on my last 2 phones active sync worked well with updating to custom roms,seems like my Pure produces the same error after the attempt, its a communication error "ERROR [262] : UPDATE ERROR", now recovering from the error is not a issue, we all have familiarity in that area but I was wondering if it could be something as simple as the cable that was sent with my phone or if its possible to flash rom through sd card as opposed to using active sync?
drearystate said:
Hi, I don't post much if at all, normally you guys have it right on the button, this is my 3rd phone to run custom roms on but for some reason it just freezes on the "Updating ROM image on your PDA Phone..." screen and doesn't continue past, on my last 2 phones active sync worked well with updating to custom roms,seems like my Pure produces the same error after the attempt, its a communication error "ERROR [262] : UPDATE ERROR", now recovering from the error is not a issue, we all have familiarity in that area but I was wondering if it could be something as simple as the cable that was sent with my phone or if its possible to flash rom through sd card as opposed to using active sync?
Click to expand...
Click to collapse
Yes, you can flash through storage card, just rename the .nbh to TOPAIMG.nbh, Put in root of storage card and enter bootloader mode.
You have HSPL'd, right?
Bruce Inman said:
Yes, you can flash through storage card, just rename the .nbh to TOPAIMG.nbh, Put in root of storage card and enter bootloader mode.
You have HSPL'd, right?
Click to expand...
Click to collapse
I was just going through the thread. I have the same issue. i have place topaimg.nbh in the root of storage card and entered bootloade mode, it shows loading and is stuck at 0%.
HSPL is 1.83. Went through entire thread of HSPL but unfortunately didn't find any solution.
arun.ramachandra said:
I was just going through the thread. I have the same issue. i have place topaimg.nbh in the root of storage card and entered bootloade mode, it shows loading and is stuck at 0%.
HSPL is 1.83. Went through entire thread of HSPL but unfortunately didn't find any solution.
Click to expand...
Click to collapse
Just to confirm, you have to name it exactly "TOPAIMG.nbh".
With all of the people that have tried all methods and still can't flash, something must have changed in the stock SPL.
Hello people
Hello, did anybody found the way to flash HTC PURE , I have the same problem 0%
Thanks
same problems here
i have same problem with pure to.
coldun187 said:
Hello, did anybody found the way to flash HTC PURE , I have the same problem 0%
Thanks
Click to expand...
Click to collapse
From HTC site (HTC Pure support):
What is a Soft Reset and how is it performed?
A soft reset basically resets the memory structure in the handheld. This recovers the device from memory conflicts, corrupted system service chains (mainly due to attempting hacks), memory leaks, and system lockups due to the “Fatal Exception” program errors. Removing the battery from the device while it is still powered on is NOT a soft reset and can actually damage the device.
A Soft Reset is performed by:
Remove the Battery cover and the Stylus from the device.
Insert the tip of the stylus into the Reset hole located at the entry point of the stylus silo.
The device will reboot.
My phone got wet and now it starts up but gives me the black screen where I can press volumeup to hard reset, but it doesn't respond when I do this. I'm trying to flash it or do something to fully revert it to a brand new state, but I obviously can't use active sync and cannot get access to the phone's internal memory. How can I do anything?
flash through sd card. good luck with that. Hope you did try the phone completely
I was hoping there was a way to flash with just the sd card. Would you be kind enough to at least link me to where I could find instructions for this?
The phone is dry. It starts up fine and keeps on, stuck at that black screen. It's been a while since I got it wet.
Thanks.
8gkl said:
My phone got wet and now it starts up but gives me the black screen where I can press volumeup to hard reset, but it doesn't respond when I do this. I'm trying to flash it or do something to fully revert it to a brand new state, but I obviously can't use active sync and cannot get access to the phone's internal memory. How can I do anything?
Click to expand...
Click to collapse
mutantblack said:
flash through sd card. good luck with that. Hope you did try the phone completely
Click to expand...
Click to collapse
8gkl said:
I was hoping there was a way to flash with just the sd card. Would you be kind enough to at least link me to where I could find instructions for this?
The phone is dry. It starts up fine and keeps on, stuck at that black screen. It's been a while since I got it wet.
Thanks.
Click to expand...
Click to collapse
Well it won't matter because it has water damage. Are the little stickers inside pink? If so then they will charge you for any repairs so it won't matter what ROM you have on..
Who will charge me for repairs?
I don't recall ever saying that I will give it in for repairs, because I am aware of the voiding of the warranty when the wet seal becomes pink. Because I realize all of this, I decided to give it a chance flashing the phone and starting it with a new install to see if that would work, as my last chance to get anything out of it.
8gkl said:
I was hoping there was a way to flash with just the sd card. Would you be kind enough to at least link me to where I could find instructions for this?
The phone is dry. It starts up fine and keeps on, stuck at that black screen. It's been a while since I got it wet.
Thanks.
Click to expand...
Click to collapse
Try this way
http://forum.xda-developers.com/showthread.php?t=550540
Thanks, but I checked those instructions out already, and they assume that I am able to use activesync with the phone. The phone doesn't boot far enough for activesync on my computer to recognize it. All I can do it insert the 16gb microsd card into my usb card reader and put whatever I want on it, and then back into the phone. I would think there is a way to just put the rom onto the sd card and put it into the phone, and then press some kind of bootloader startup key combination so that the phone goes straight to the installation.
8gkl said:
Thanks, but I checked those instructions out already, and they assume that I am able to use activesync with the phone. The phone doesn't boot far enough for activesync on my computer to recognize it. All I can do it insert the 16gb microsd card into my usb card reader and put whatever I want on it, and then back into the phone. I would think there is a way to just put the rom onto the sd card and put it into the phone, and then press some kind of bootloader startup key combination so that the phone goes straight to the installation.
Click to expand...
Click to collapse
If you take a look a little further down the very same page that SonyEX1 provided, you will see this:
Flashing Via MicroSD Card
1. Make sure your microSD is Formatted to fat32 (you dont have to delete all files but it is safer if you do)
2. Download your prefered Rom from the Rhodium Rom Develpoment Page and unzip/unrar it to your PC
3. Goto the Roms Folder and rename the .nbh file to RHODIMG.nbh
4. Copy the RHODIMG.nbh file to the root of your MicroSD Card
5. Plug the MicroSD Card into the phone
6. Enter the BootLoader screen, you will first see a tri-color screen with the phone and SPL Information at the top
7. Follow the On Screen instructions to start the update
8. After flash has completed, press the reset button with the stylus to reset the device.
As has been stressed many a time on this forum, please make sure that you read through all of the instructions (entire page) very carefully prior to flashing.
http://forum.xda-developers.com/showthread.php?t=550540
Good luck.
Mike.
Thanks, I noticed that note at the end of the post, but the only rom that I think I would be able to flash is the stock one, because I don't have HardSPL. I can't get HardSPL because I can't activesync the phone to my pc. So I pretty much need the stock rom in nbh format to try anything at all.
I noticed that when I enter the bootloader and plug the phone in to my computer via usb, the computer detects something and says that an htc device is attached, but microsoft activesync still doesn't recognize it and the phone doesn't show up in my computer.
So I guess the search is on to find an .nbh format for the stock rom.
8gkl said:
Thanks, I noticed that note at the end of the post, but the only rom that I think I would be able to flash is the stock one, because I don't have HardSPL. I can't get HardSPL because I can't activesync the phone to my pc. So I pretty much need the stock rom in nbh format to try anything at all.
I noticed that when I enter the bootloader and plug the phone in to my computer via usb, the computer detects something and says that an htc device is attached, but microsoft activesync still doesn't recognize it and the phone doesn't show up in my computer.
So I guess the search is on to find an .nbh format for the stock rom.
Click to expand...
Click to collapse
I am not sure what carrier you are on, but if you download the stock ROM from whichever carrier you need (or the generic HTC ones if you have an unbranded one) it should be an .EXE file.
You should be able to right-click on the .EXE and extract the contents into a temp directory using any decent compression software (I use 7-zip). There should be a RUU_signed.nbh file that you can rename, copy to your microSD and manually flash from there.
(And if you already didn't know, you enter bootloader mode by first powering off the phone, hold down the VOL Down key, and power the phone back up while holding the VOL Down key. You should then see the tri-color screen above. This part isn't mentioned in the instructions above and assumes you already know how to get into bootloader mode.)
Thanks. I didn't know that you could extract .exe's, so I have been searching and found someone's uploaded stock rom in .nbh format. I put it on the sd card and went to the bootloader with it. Right now, It's been at a white screen that just says "Loading...". This has been going on for the past 5 minutes without changing. I don't know how a successfull rom flash is supposed to look like, so I don't know if it's working or not.
Is it supposed to be moving or what? How long do I wait before snatching the battery?
UPDATE:
I guess the stock rom that I tried previously was faulty or something, because it was hung on the loading screen, so I downloaded the TMOUSA one from their website, extracted the NBH, and put it on the SD card. Everything started looking really good because I had a progress bar and it said something like Radio OK and something else was OK and it was loading the ROM, and then all of a sudden it rebooted into the bootloader, gave some kind of error that I can't really read because it is written on top of the other text in the bootloader, goes into the Loading screen to begin installing the rom, and then reboots again. This is the loop that takes place right now.
It seems like the problem is a dead battery though, because it started flashing fine that first time, and now the phone won't even turn on unless I plug it into USB power from the wall or a PC. But when I do plug it in, it just goes through this bootloader loop. So here is where I'm stuck.
It seems like I need a fully charged battery to attempt to reflash the stock rom or install any other rom because when the phone is in bootloader, it doesn't charge the battery, and I have no means of charging it.
8gkl said:
It seems like I need a fully charged battery to attempt to reflash the stock rom or install any other rom because when the phone is in bootloader, it doesn't charge the battery, and I have no means of charging it.
Click to expand...
Click to collapse
you should be able to charge te phone when it is completely off/ Pull the battery out, put it back in (do not power it up), and charge it over night (or at leastfor a couple hrs)
If the phone was fine before you got it wet, what makes you think re-flashing the stock rom will make it better?
I once crashed my ROM while flashing and wasn't able to do at least anything.
There was no USB-Connection or something else.
At last I entered the bootloader and there the USB-Connection was working and my Computer recognized the Mobile. So I suggest you to try this. To enter the bootloader look for any tutorials around here.
Edit: Aaargh, havn't seen your last post, so forget about it
cjm1979 said:
If the phone was fine before you got it wet, what makes you think re-flashing the stock rom will make it better?
Click to expand...
Click to collapse
Because as I've mentioned previously, after getting wet, the phone boots up into a black screen where it tells me that I can press the VolUP button to hard reset or anything else to soft reset. Pressing any keys at that point doesn't do anything and I can only shut it down by taking out the battery. So I decided to at least try reflashing the rom. It looked like it was installing fine with the last power the battery had, but now I have no hope.
8gkl said:
Because as I've mentioned previously, after getting wet, the phone boots up into a black screen where it tells me that I can press the VolUP button to hard reset or anything else to soft reset. Pressing any keys at that point doesn't do anything and I can only shut it down by taking out the battery. So I decided to at least try reflashing the rom. It looked like it was installing fine with the last power the battery had, but now I have no hope.
Click to expand...
Click to collapse
i have heard of shops that charge batteries up but never seen one. I suppose you may be able to buy a stand alone battery dock if they do one for the Touch Pro 2. Dont you know anyone with the same phone that could charge it for you?
No I don't really know anyone with the same phone. I've called 4 shops and all said that they either don't have the same phone to put the battery in to charge, or can't perform this kind of service. I ended up taking apart a usb cable and formulating my own usb charger. Charging right now, will report on how this worked out.
Ok. This is the kind of device i meant.
amazon.com/European-Desktop-Cradle-Battery-Charger/dp/B002JJC7OW
I dont know whether i have asked a dumb question or not but i've searched for all the forum, it's all "discussing" and too much scattered thing that i still cant see the specified way for my phone.
Yes, again this question, I tried to flash Energy Rom on my phone, by USB and by SD card, everytime i reboot or turn off my phone, i will need to connect through USB to boot on, or not it will display tri-color screen and flash No Image File. I copied the image file to SD card and now when i boot the phone it tell me to update the rom on SD card... And if i delete this image on my SDｃａｒｄ then...it's again, nothing too much to say...
Is there any way to let my phone boot on without USB wired and no tri-color screen (i guess i hate that much).
Hope getting help from you all, and please tell me step by step, i'm newbie anyway, please.
By the way, anything related to mtty or HardSPL, SoftSPL i still dont work it out. Please give me some tips.
xgenvn said:
I dont know whether i have asked a dumb question or not but i've searched for all the forum, it's all "discussing" and too much scattered thing that i still cant see the specified way for my phone.
Yes, again this question, I tried to flash Energy Rom on my phone, by USB and by SD card, everytime i reboot or turn off my phone, i will need to connect through USB to boot on, or not it will display tri-color screen and flash No Image File. I copied the image file to SD card and now when i boot the phone it tell me to update the rom on SD card... And if i delete this image on my SDｃａｒｄ then...it's again, nothing too much to say...
Is there any way to let my phone boot on without USB wired and no tri-color screen (i guess i hate that much).
Hope getting help from you all, and please tell me step by step, i'm newbie anyway, please.
By the way, anything related to mtty or HardSPL, SoftSPL i still dont work it out. Please give me some tips.
Click to expand...
Click to collapse
Firstly, you have not written what happens to you very clearly...its is all very confusin..from what i understand, your phone boots only if you connect it to the PC via USB...With WHAT METHOD did u FLASH your phone for the FIRST time??
Im also no expert, but i wil make an attempt...what is ur current status...does your phone start at all??
circleofomega said:
Firstly, you have not written what happens to you very clearly...its is all very confusin..from what i understand, your phone boots only if you connect it to the PC via USB...With WHAT METHOD did u FLASH your phone for the FIRST time??
Im also no expert, but i wil make an attempt...what is ur current status...does your phone start at all??
Click to expand...
Click to collapse
As i pay attention to the bootloader, i'm sure that it's already made the HardSPL and the phone can recognize the image on the SD Card or by USB method. The first ROM was flash on the phone is not me, this is my friend's phone, I'm just trying to help him around then.
I tried to flash the rom by USB method, but when i restarted the phone without the USB connected to PC, it did show the bootloader (i just touch the power button, not volumn button or any other key)~ then i plug USB which connect the phone to pc, soft reset it and it boot to the system again.
I try to flash it by SD-card method but it still the same. I mean that the phone can be flashed new ROM, but it's just keeping get into the bootloader everytime i restart the phone
If the image is on the SD Card it'll tell me to upgrade ROM, if the image is not on the SD Card then "No Image File!" was flashed on~
Any ideas? My friend tells me that this happened when he tried to install Sogou - chinese input application. Is there any conflicted that cause this matter?
for little detail, the phone always shows up Successfully, but it still enter the bootloader mode at next restart. Is my flash-job done or just a mistake one?
additionally, this may be bad... remove the battery doesnt work. Please help.
help me please, do i have to hardspl again? I still cant enter WM unless i have a usb wire connected phone to pc and softreset it. Any idea?
xgenvn said:
help me please, do i have to hardspl again? I still cant enter WM unless i have a usb wire connected phone to pc and softreset it. Any idea?
Click to expand...
Click to collapse
hm, since you said the first flashed job was not yours, i think it's better that you repeat the whole procedures again starting from hardspl. but make sure you're using the correct version. re-download again if you're not sure.
also while most people rarely done so, it's bad to have multiple rom image exist in any root folder in your phone, storage card and your pc flashing tool folder (.nbh, .rom, etc), but sometimes people do forget or **** just happens.
I recommend that you remove both sim & microsd card before going any further.
then try to boot into wm with usb cable connected like you said.
take a quick look at folder and file structure in the rom. from here i would do it slightly different than others, with no battery pulls, just using the reset button. (imho, every battery pull may cause unforeseen damage especially with power still running.)
a. push hard reset combo button (don't let go) and push reset for a few secs to hard reset.
b. after hard reset rebooting the phone, push bootloader/rom update combo buttons and hit reset for a few sec. remember to keep pushing those buttons while you release the reset pin.
c. reflash hardspl, repeat step b, reflash rom. allow rom to finish doing its job. some rom may go to sleep while installing/customizing, don't let that happend.
d. just do random thing like play a game or whatever for a few minutes or more. then soft reset or power down.
e. turn on phone and wait, if problem's solved. if it is, hard reset again. continue as usual. if it's not, try other rom (ask people for md5 checksum, compare with your download). if none works, find more help.
D-jack said:
hm, since you said the first flashed job was not yours, i think it's better that you repeat the whole procedures again starting from hardspl. but make sure you're using the correct version. re-download again if you're not sure.
also while most people rarely done so, it's bad to have multiple rom image exist in any root folder in your phone, storage card and your pc flashing tool folder (.nbh, .rom, etc), but sometimes people do forget or **** just happens.
I recommend that you remove both sim & microsd card before going any further.
then try to boot into wm with usb cable connected like you said.
take a quick look at folder and file structure in the rom. from here i would do it slightly different than others, with no battery pulls, just using the reset button. (imho, every battery pull may cause unforeseen damage especially with power still running.)
a. push hard reset combo button (don't let go) and push reset for a few secs to hard reset.
b. after hard reset rebooting the phone, push bootloader/rom update combo buttons and hit reset for a few sec. remember to keep pushing those buttons while you release the reset pin.
c. reflash hardspl, repeat step b, reflash rom. allow rom to finish doing its job. some rom may go to sleep while installing/customizing, don't let that happend.
d. just do random thing like play a game or whatever for a few minutes or more. then soft reset or power down.
e. turn on phone and wait, if problem's solved. if it is, hard reset again. continue as usual. if it's not, try other rom (ask people for md5 checksum, compare with your download). if none works, find more help.
Click to expand...
Click to collapse
I've just tried out the task29, it's done normally, then flash the new rom.
1. I dont think the rom are buggy, because i changed between 2 roms and it's the same matter.
2. I dont need to use bootloader/rom update combo button because it's directly entered whenever i turn on the phone (without connected to pc) (i really really dont know why)
3. Hard reset and i have my WM work again but it's still the romupdate at boot time.
I wonder if jumpSPL did all this problems, I tried mtty by task 0 and set 14 0 but it wont restart the phone, tried to format the ROM by mtty (task 32) but it wont weep out, errors given: bad... at address...
Why does it always want me to update the ROM? Is there anything wrong with jumpSPL?
the problem still, please help me give a look to this.
ouch, last time I use mttty were ancient wm2003 era. i'll try to look for info, but can't promised anything.
at this point it's recommended to reflash the complete original stock rom, undo hardspl.
check the hardspl thread about restoring to factory default. best luck to you.
So right now, my phone keeps on getting stuck at the 'android' word bootscreen. It keeps repeating and seems to go on forever! Someone please help me! I heard its due to rooting! Can anyone confirm this?
What did you do? I tried once to install aps 2 card and the phone stood in android screen about 20 min
Anyway if it doesn't start. Flash new android: nand restore or sbf
.
Sent from my Milestone using Tapatalk
Finally somebody replied back. Its been going on for days, I've removed the battery, placed it back, same thing.
Also, sorry but I have no idea how to flash something. How do I do it? And it doesn't even go past it.
I should spend on time in this sub-forum.
If you have flash a custom ROM then just reflash it or try another ROM.
It's highly, highly unlikely that your phone it breaked so don't worry about.
I have never flashed a custom rom. I don't even know how to flash in the first place.
turn off hp.try to hold up-dpad(towards screen) button and switch on your milestone.
then you see black screen written Bootloader.
battery OK.
OK to program
connect USB
data cable.
if you can go into this screen, then u can start to learn to flash vulnerable recovery.
and ready to install custom room.
google around on how to instal vulnerable recovery for milestone .
under18 said:
turn off hp.try to hold up-dpad(towards screen) button and switch on your milestone.
then you see black screen written Bootloader.
battery OK.
OK to program
connect USB
data cable.
if you can go into this screen, then u can start to learn to flash vulnerable recovery.
and ready to install custom room.
google around on how to instal vulnerable recovery for milestone .
Click to expand...
Click to collapse
Yep, I can go into it. But I checked, and can't find how to install a vulnerable recovery. Any help?
My site is down atm, but this may help;
http://forum.xda-developers.com/showthread.php?t=932196
shut down phone ->hold down hard keyboard x key and power button->when M logo appears release power button but keep pressing x key until recovery mode shows up
there is an option for clearing data/factory reset
you'll loose everything but it propably fix the problem
Including my contacts?
ray243 said:
Including my contacts?
Click to expand...
Click to collapse
your contacts if you have chosen it will be at your Gmail account and they will be restored.
So i had damages rom on my hero for over a year now and it worked fine then yesterday i unmounted my sdcard put another one in and the phone froze i restarted it, did nand restore, reflashed the rom and everything and nothing it just keeps boot looping so today i hard reset it ( hold down home key, back key and power button) hoping i could just start from scratch and nothing its still just boot looping. I tired to flash another rom but guess since the phone wont fully turn on my comp doesnt recognize it or pick it up... Please help dont know what else to do. Thanks
digital3721 said:
So i had damages rom on my hero for over a year now and it worked fine then yesterday i unmounted my sdcard put another one in and the phone froze i restarted it, did nand restore, reflashed the rom and everything and nothing it just keeps boot looping so today i hard reset it ( hold down home key, back key and power button) hoping i could just start from scratch and nothing its still just boot looping. I tired to flash another rom but guess since the phone wont fully turn on my comp doesnt recognize it or pick it up... Please help dont know what else to do. Thanks
Click to expand...
Click to collapse
It sounds like you can get into recovery. If so, wipe data,cache,boot,system,dalvik cache. Then flash a new ROM and gapps (from the same thread). It would REALLY help if you would state what recovery and version# you have, what ROM you were trying to flash with what gapps, what radio baseband you have, whether you are s-off or not, and what all you have tried so far, with elaborate steps.