Tilt 2 HARDSPL with Micro SD - Touch Pro2, Tilt 2 Windows Mobile ROM Development

Ok, ive searched high and low with conflicting answers. Majority of info says no, no SD Hardspl is possible via micro sd, but a few posts say it is.
Is it possible??
My USB isnt working (even on bootloader) and im stuck with an Orange ROM!! (and by God Orange ROMS are A T R O C I O U S!).
HAve i a HARDspl alternative to USB sync???

Hello, seems that I was in a reverse situation couple of months ago: my TP2' USB stopped working, battery drain inacceptable and the phone stuck on Energy (read: unofficial) ROM. I was able to flash the WWE stockROM back but not to re-SSPL through USB of course.
What's worked for me:
- I've simply extracted the .nbh from SSPL package, renamed it to RHODIUM.nbh and flashed from SD card just like I'd flash a ROM
(after reset the phone went a bit mad )
- switched to bootloader and flashed the StockROM from SDcard again, and... voila
(After that, I have claimed the warranty repair successfully - and nobody would have said the phone was not in "as-shipped" status.)
May something like that work for you, too?

You can flash the stock SPL via SD card. But you can't flash HardSPL via the SD card, because it still needs an Internet connection for its licence checking.

Thanks for the replys, but is what im hearing this...
I can flash any Orange Roms but nothing else?
Tried to flash the new HTC Rom but 'not allow'

Quincey113 said:
Thanks for the replys, but is what im hearing this...
I can flash any Orange Roms but nothing else?
Tried to flash the new HTC Rom but 'not allow'
Click to expand...
Click to collapse
Yeah, if you have an Orange-branded phone (as opposed to a plain HTC one) then you won't even be able to flash official HTC ones, only Orange ROMs.

Related

mda mini PM10A dead by wrong rom

hi all
my mda dead now when i put usb cable its kepad lights only blink some time and speaker beep.
this happend with wrongly upgrade with blue angle rom.
mda detect with pc ok.
any suggestion.
thanks in advance.
try entering the bootloader and then try flashing an official rom from your phone provider
I think your device is a brick now. The Blue Angel ROM changed the bootloader. No chance to restore.
ChrBeck, weren't you the one who suggested that one can simply copy a valid bootloader to a SD Card (then use the NTRW.exe trick)?
No, I wasn't. Because I know that if you can't get in bootloader you can't install a new one. I've never heard that there is a trick to reeinstall the bootloader, if there is no one.
There is nothing wrong with the 'trick'. I know that it'll ask you to push the power button to flash from SD card (if done properly). Forget it then.
Jani-Jan, needs to try restoring the ROM using another PC (with a different OS).
OK, maybe this trick is from Prophet and works on Charmer. Sorry for that. And the Idea with an other OS is good. I think Linux will work. If you need translated tools write I will try.

Unbrick Trinity From SD

Need a favours over here. Recently, i bricked my trinity. P3600 more precisely Dopod D810 (i flashed wrong ROM -> Unpacking cooked rom for trinity but i merge it with -Hermes cmd in NBMerge! houh... so stupid! ). Soo... just not what i expected, Rom flashing stop on half, SR my trin and tada.... 3Color screen bootloader popup! haaarggg, i try flashing another rom using any rom that has same CID *official or cooked rom* (some are 100% thru, but someother not) but like usual it won't start the windows (just blank/black screen with green led[ always on!) Never been like this before! Have been flashing several times using any cooked rom by great chef on trinity but this time! :doh: damn it! my bad.
i found solution on the forum *Unbricking Trinity Stuck on Bootloader* but since my usb port can't be detected on my vista/xp machine, whether i disable AS and changed my usb cable it doesnt work at all, on mtty too! so i can't use that utility. i try run install sspl olipro 1.3 but it never changed my spl at all. now i can't use my trin at all cuz allready dead.
btw this is the info on trin 3color screen bootloader:
IPL 1.00
SPL 3.20 OLIPRO
anysolution for bringing back my trinity from the death? maybe a tools/utility to unbrick trinity from SD or something like that, which not involved any pc connection, without bring this devices to htc center of course.
I hope any expertise on this forum would helped me sort out this probs.
Sorry for my english and thanks for reading my post.
Read this :http://forum.xda-developers.com/showthread.php?t=308691 download splxploit-windows.zip (935.1 KB, 7619 views) put phone in bootloader run splxploit when bootloader change
After this download full rom here is link:http://rapidshare.com/files/21174752/RUU_Trinity_HTC_WWE_1.15.405.5_6275_1.20.00.11_12201_Ship.exe
Then flash full rom bat do not disconnect usb cable in any step.
Before use any step disable active sync.
Usb are dead
Gsmhacks thanks for ure reply. I have tried that one, and lot read ing on wiki. But since i cant use the usb i cant use that splexploit whether on live linuxcd, or .Net version even win version. The usb port cant be opened . I think i broke the usb pin. From the beginning everytime i flashed my trin i never used ruu utility, i always do the sd card method and that is the best and easiest method and it works for me.
I just curious perhaps can anyone or is there any utility to unbrick trin via sd card. I knew a lot a people has bring their trinity life from dead by using htc stackflow splexploit. I hope that was work for me too! Too bad my usb are dead. Damn!
Here what you need bat only work if you have hard spl
If you install hard spl before brick trinity you can use SD CARD to flash trinity. YOu need to formate sd card to FAT32 with Card Reader donwload full rom here is link: http://rapidshare.com/files/21174752/RUU_Trinity_HTC_WWE_1.15.405.5_6275_1.20.00.11_12201_Ship.exe
then extract and file RUU_Signed.nbh rename to TRINIMG.nbh and copy it to the root folder of your miniSD card.
Here is full instruction again also first format sd card to FAT32 !!!! VERY IMORTANT to format sd card to FAT32 or all other step will not work THEN:
1. Extract the .NBH file from your prefered ROM upgrade: In windows use winrar (right click) to extract the contents of the exe file. In Linux / MacOS use cabextract (or you can also use winrar via wine).
2. Rename the .NBH file to TRINIMG.nbh and copy it to the root folder of your miniSD card.
3. With miniSD card inserted on the phone, start the bootloader (hold Power button on right side and Camera button at same time and stick with stylus in RESET on bottom).
4. You should see the screen pictured on the left, confirm flashing on screen by pressing the power button.
5. Flashing might hang after some time but this is normal. Just wait. Complete flash takes about 30 minutes, so check your battery or connect to charger before the flashing process starts.
6. When flashing completes soft-reset your device.
and you will flash and unbrick trinity bat this only work if you install before this hard spl i mean cid unlock trinity. if not you must fix usb port.
That will work? I hope so
Ok then i'll try flashing using that rom. Oo, i have install hardspl btw and so far flashing using sdcard method no probs. But after i bricked my trin flashing doesnt smooth like be4. Always gave me error 0018003 update fail on the halfway, i guess because i have bad nand on trin and probably cuz cooked rom.
Can u give me another link, perhaps on xda ftp. rapids so slow 4 me. Btw i have download dopodasiawwe official rom on xda ftp *twice but still when i tried to run the package it gave me corrupt archive integrity fail w!f.
Thanks gsmhackerns, i downloading the package now!
Perhaps you can find a way to make a goldcard for Trinity?
See http://forum.xda-developers.com/showthread.php?t=437996
That's what i looking for! Thanks.
Humm, superb. Yay, great! Thank you stepw. Even its for elf with a little mod i hope this will work. Once again thank you.
Stepw, i have tried making the gold card, everything went ok. I have temp. cid *supercid* but the probs now is i can't download http://rapidshare.com/files/21174752/RUU_Trinity_HTC_WWE_1.15.405.5_6275_1.20.00.11_12201_Ship.execan someone uploaded to somewhere else. Rapidshare crap! perhaps on xda ftp.
thanks!
goldcard cannot help in such a situation.
I can however make an SSPL that loads off SD card - just like for kaiser you will be able to use it because you are already on hardspl.
then that will allow you to flash stock SPL.
PM me and send your MSN address, so we can test it out. if it works i'll post it in this thread too in case others get stuck also
cmonex said:
goldcard cannot help in such a situation.
I can however make an SSPL that loads off SD card - just like for kaiser you will be able to use it because you are already on hardspl.
then that will allow you to flash stock SPL.
PM me and send your MSN address, so we can test it out. if it works i'll post it in this thread too in case others get stuck also
Click to expand...
Click to collapse
Indeed. Youre right cmonex, it doesnt make any difference at all 4 my trin. After several tried using and making goldcard 4 trin, finally i made working goldcard4trin, but gosh it still stuck when i tried to update the os (update os fail) humm anyone.
Sorry for wasting your time with Goldcard, I have overlooked that you have a hard spl on your Trinity. In this case goldcard doesn't make a lot of difference.
And there's no trindiag.nb to the best of my knowledge that could be used instead of SSPL cmonex is suggesting to run from SD.
Back to the topic, sounds like you have some "bad" blocks in flash and OS can't be flashed. Bad blocks can be reset with "task 2a" command, see this thread for more details:
http://forum.xda-developers.com/showthread.php?t=330496
The question is how to run it without USB and I don't have an answer for you
Some people have previously mentioned they managed to flash smaller OS images when larger images failed, perhaps if you try flashing some minimal vanilla ROM, it will succeed?
Bad NAND, Yup!
Ya... as i mention before yup i do have bad nand block on my devices. Using manila rom with smaller img size the flash went 'OK'. But it doesn't boot at all infact just black screen with green led on.
Okay the only solution probably use mtty and do task 2a if i'm not mistaken. But like you said "The problem is the USB port". I think the port is ok cuz i already tested it connecting my usb to my trin without inserting the battery and the red led *magenta* is on. humm, weird!
But if something can make it working without involving any pc connection it would be a great achievement. hahah! well i supposed i have to put my trin on bunker before someone can make it happens
I asked SEA in my country and they recommend me to changed the machine it self and they charge me around US $160 ho...ho.. too "wideeeeee" for college boy like me
Same problem, i flashed the rom
RUU_Trinity_DOPODASIA_WWE_3.00.707.18_6275_1.46.30.11_108_Ship
and after that i tried to flash a new radio!
power+cam and the cell phone did not show usb, then i used sspl to rum the radio but it locked at 0%
after that it is stucked at bootloader screen
ipl 1.0
spl 3.20 .....
but no usb and no sd card !!
did i lost the cell phone?
there is no jtag ou something like that ?
so now... you still want this SSPL? i'm thinking of patching one up to automatically run task 2a maybe. or just restore stock spl for warranty service if that's what you have in mind. but you didn't really reply to that offer?
Please if you could build a sspl for this condition it would be enough because once sspl i can run a new ruu with hard-spl again ! the problem i believe was caused becaus this original rom's have a spl.nb inside , in the screen we read teh information about the olipro spl but i thing teh original spl.nb messed up the hard spl!
There is another problem, i formated to fat32 my card and put a TRINIMG.nbh of a rom inside and he did nothing!! same card in elf with ELFIMG.nbh of a rom runs great!!
It means that this spl of mine will not flash from card? goldcar would help?
and cant i flash something in serial ? like a jtag or something?
Anyhelp will be more than apreciated!
sorry the bad english
Needed!
Cmonex, sorry for longtime haven't seeing this thread again. okay i really need your help btw if you willing to help me. The spl your talking about perhaps can sort out the probs (i hope) at least we tried. as for task2a cmd to clear the bad nand block is none usefull for me since usb conn. are definitely drop dead.
how about patch the SSPL to do task2a cmd to solve the bad NAND block first.
dinizbruno said:
Please if you could build a sspl for this condition it would be enough because once sspl i can run a new ruu with hard-spl again ! the problem i believe was caused becaus this original rom's have a spl.nb inside , in the screen we read teh information about the olipro spl but i thing teh original spl.nb messed up the hard spl!
There is another problem, i formated to fat32 my card and put a TRINIMG.nbh of a rom inside and he did nothing!! same card in elf with ELFIMG.nbh of a rom runs great!!
It means that this spl of mine will not flash from card? goldcar would help?
and cant i flash something in serial ? like a jtag or something?
Anyhelp will be more than apreciated!
sorry the bad english
Click to expand...
Click to collapse
no usb, no sd, no chance sorry. jtag it or get it serviced or get another phone.
as for jtag, hermes jtag has been worked out by scholbert. trinity is probably the same, but you will have to find the pins. the rest of the process will be the same.
Dear all,
I can't go to bootloader screen ..fff before I had on my trinity faman 4.03 rom and I would change with the NiAX rom... after 3% restart and I think that my phone brick and my phone stay on htc screen fff please help
I have windows vista and even if i follow all steps pfff it changes nothing...after hard reset ...fff please help ...
I think my trinity is out :-(????????????????????????
Please help,
The O.S is more important to these operations than can be stressed - for a 99% safe flash Win XP is your best bet , I have had nothing but error 260,270 halfway flashed roms and usb faults running on vista and since I had my original bricking episode - NOTHING , I repeat NOTHING including genuine roms has flashed without a recovery or at least without doing something strange in the process - SPLXPLOIT has been a saviour here , without it I would've been lost.
Cant the O.P simply use another machine to test out the USB theory ?
ALIVE AGAINnnnnnnnnnnnn!!!!!!!!
My p3600 was stucked att bootloader, and wont give "usb" and do not read TINIMG.NBH (tried on elf with ELFIMG.nbh and the card was great)!
I did a golcard with the post on elf about it and the cell with the gold card inside was the same, no trinimg.nbh and no usb.............
BUT..............
with the goldcard inside, turned OFF, i placed it on the usb cable off the pc and the device booted to the bootloader screen, but this time he got "USB" , before flashing anything i removed the card , and putted switched off in the usb, booted with "serial" with card and pressing power and then placing usb still "serial" message!
I putted the card, did not switched on , placed on the usb and waited for it to boot for it self , and for my surprise "usb".
Flashed stock rom, and it booted nice!!!
Please try!
saved my day!
sidekraouf95 said:
Dear all,
I can't go to bootloader screen ..fff before I had on my trinity faman 4.03 rom and I would change with the NiAX rom... after 3% restart and I think that my phone brick and my phone stay on htc screen fff please help
I have windows vista and even if i follow all steps pfff it changes nothing...after hard reset ...fff please help ...
I think my trinity is out :-(????????????????????????
Please help,
Click to expand...
Click to collapse
I have to know how to repair my phone please... nobody can explain precisely how to put my phone on bootloader using my sd card directly from my computer under vista...???

SE Updater failed to install new rom, what is the best thing to do now?

Hello,
I know you guys got some excellent walkthroughs, roms, programs and threads where you've helped a lot of people out but I could really use some personal feedback. I had hoped to fix my phone using one of the excisting threads but unfortunalty I can't get it to work with those.
My problem is one I've seen more of in here, I used the SE updater and it froze at 53%, I did what the program said, reconnected and it froze again at 12%, and again, again, etc. So I disconnected thinking it might be a bad USB port. But then the updater didn't recognise my phone at all. So I used the mtty program suggested in some of the threads and I got past the red/green/blue screen but now it's stuck at the Sony Ericson logo, as if WM6.1 is gone.
This is what the red/green/blue screen currently states:
KOV110
SPL-0.78.0000
MicroP1-787
MicroP2-707
From what I gather this means I can't flash roms, right? I tried making it a hard-spl but when I use the tool it says it can't connect.
So is there anyway to get a rom on it and bring it back to life?
Thanks inadvance!
Get an original rom from here : http://forum.xda-developers.com/showthread.php?t=475482
copy .nbh file from the package onto your sd card and rename it to : Kovsimg.nbh then bring phone into boot loader via : vol down + power.
It should flash the rom now. i the problem is still present after that you
have to deal with mTTy but first try the flash...
i think you could also bring phone into bootloader without sd card inserted then connect usb cable, display should now print 'USB',and after that start rom update utility.
regards
meska said:
Get an original rom from here : http://forum.xda-developers.com/showthread.php?t=475482
copy .nbh file from the package onto your sd card and rename it to : Kovsimg.nbh then bring phone into boot loader via : vol down + power.
It should flash the rom now. i the problem is still present after that you
have to deal with mTTy but first try the flash...
i think you could also bring phone into bootloader without sd card inserted then connect usb cable, display should now print 'USB',and after that start rom update utility.
regards
Click to expand...
Click to collapse
Thank you for your reply, I will do as you said although I've already tried something similiar to this. I believe the problem was that I couldn't flash roms from my SD since I don't have the hard SLD. But I will try it anyway as soon as I get home.
In the mean time I would love to hear more ideas about how to fix my phone.
Ronnet said:
Thank you for your reply, I will do as you said although I've already tried something similiar to this. I believe the problem was that I couldn't flash roms from my SD since I don't have the hard SLD. But I will try it anyway as soon as I get home.
In the mean time I would love to hear more ideas about how to fix my phone.
Click to expand...
Click to collapse
You really need have to flash the HardSPL first as, based in your above post, you still have not done that. It will be useless to flash cooked ROM with that. If you can still power on your phone and you have an activesynch in your computer, i suggest you download the HardSPL first and update your phone using your PC. If you are successful doing that, then you can flash all you want.
original roms will still work with original spl... but nevermind =P
laurence0609 said:
You really need have to flash the HardSPL first as, based in your above post, you still have not done that. It will be useless to flash cooked ROM with that. If you can still power on your phone and you have an activesynch in your computer, i suggest you download the HardSPL first and update your phone using your PC. If you are successful doing that, then you can flash all you want.
Click to expand...
Click to collapse
My phone can still power on in the sense that it shows the Sony Ericson logo or that I can access the three collor screen. But it won't launch WM6.1. I also have a problem with updating to hard DSL. It does recognise my phone because without it connected the program finds nothing and with the phone connected it wants to start updating. It says ''updating from image version: (emply) to image version: 1.00.X1 Ipress next and it opens a progress bar on both my X1 and the PC. But it never goes beyond 0% and then gives me an connection error. I think it has something to do with not being able to get passed the Sony Ericson logo. I mean the hard-DSL program does recognise my mobile but activeSync is never active because my PC doesn't recognise a WinMobile phone (since it wont go past the Sony Ericson screen)
meska said:
original roms will still work with original spl... but nevermind =P
Click to expand...
Click to collapse
Really? That might fix my device then. Could you suggest a rom from the long list? Perhaps one that works on all versions? Because I'm dutch but my mobile has always been in english so I'm not sure what rom version I had. Except that it was identified as an R2 Rom by the Sony updater before it killed my X1...
Go here
Find the latest stock rom for your country (and perhaps your carrier) and flash it
No need to have Hard SPL for that
Mopral said:
Go here
Find the latest stock rom for your country (and perhaps your carrier) and flash it
No need to have Hard SPL for that
Click to expand...
Click to collapse
I'm now downloading the initial dutch R1 firmwire, could that one work?
Mopral said:
Go here
Find the latest stock rom for your country (and perhaps your carrier) and flash it
No need to have Hard SPL for that
Click to expand...
Click to collapse
Alright so I got an R1 original rom (I now realize that the R3's were originals aswell) and it worked! I'm not sure if it was the different rom or the formatting with FAT32 that did but it works again. So I'd like to thank everyone who was kind enough to reply.
The device is incredibly slow now but now I can use the hard-DSL installer, right? DOes anyone have a suggestion for a good rom to use?
laurence0609 said:
You really need have to flash the HardSPL first as, based in your above post, you still have not done that. It will be useless to flash cooked ROM with that. If you can still power on your phone and you have an activesynch in your computer, i suggest you download the HardSPL first and update your phone using your PC. If you are successful doing that, then you can flash all you want.
Click to expand...
Click to collapse
DON'T hard-spl if you're going to flash a stock ROM. And especially if you're going to use SEUS.
Try flashing the R3A first. The R1s are way slow, as you've seen.

Possebly Bricked my Diamond, PLease Help

Dear Readers,
I have a few concerns about my recently bought Htc diamond.
The problem is that during bootup it stays frozen on the Touch Diamond bootscreens.
It has HardSPL Olinex v1.93 on it.
First i flashed back to the Stock Rom, worked fine only a couble of unexpected freezes wich made me think into using Mtty(set 14 0, task 29, task 8) to fully clear the phone and than reflash the NLD rom back on it.
Now flashing the rom went al the way 100%, and Congrats me after that.
I rebooted after that but never goes past the bootscreen with the red info lines.
So i thougt that restoring the SPL 1,93 olinex to factory setting might do the trick. But there is no way to do that since i cant get active sync to connect!
My problems is that although i can acces all bootloadmethods ,the phone is being recognized through USB, and all Rom/SPL flashes goes up to 100%. It still doesnt seem to save that rom on its memory.
and when i check the screens of the CustomRUU program it doesnt show any info add the older software version, only shows the info of the rom wich im going to flash.
If i check the USB icon on the task bar while connected to the pc, it says something like ..Qualcomm CDMA.. etc. ! the phone wasnt a CDMA version!
Any ideas?? is it Fixable or do my cats have something new to chew on??
many thanx,
Jeffrey
Copy any ROM you want to your Internal Storage, rename .nbh to diamimg.nbh, Restart your diamond and than immediately press Vol Down and back button, once in a bootloader press power button to flash rom, once finished restart Diamond, and see if ROM will be installed successfully
benko286 said:
Copy any ROM you want to your Internal Storage, rename .nbh to diamimg.nbh, Restart your diamond and than immediately press Vol Down and back button, once in a bootloader press power button to flash rom, once finished restart Diamond, and see if ROM will be installed successfully
Click to expand...
Click to collapse
Dear Benko,
How can i get acces to the internal storage?? Since the phone doesnt boot far enough to get connected in Active sync... are there other methods to acces the internal storage?
The USB trigger mode didn't work either as its not recognizing any flashdrive i connencts to it..
http://forum.xda-developers.com/showthread.php?t=540290
Especially this post:
http://forum.xda-developers.com/showpost.php?p=4194865&postcount=4
divxmaniak said:
http://forum.xda-developers.com/showthread.php?t=540290
Especially this post:
http://forum.xda-developers.com/showpost.php?p=4194865&postcount=4
Click to expand...
Click to collapse
What to do with this link??
I got Mtty running but i cant acces internal storage to copy a rom to it, and flashing by USB went all the way 100% but somehow the phone never boots in to the flashed rom.
Even trying a reflash doesnt show any signs of an older Rom being present on the phone memory..
One question about Mtty, when its said to use the ROM flasher i kinda assumed they ment the CustomRUU program. Am i right, or is there some build-in command to Flash a ROM within MTTY??
jvanzeijst said:
What to do with this link??
I got Mtty running but i cant acces internal storage to copy a rom to it, and flashing by USB went all the way 100% but somehow the phone never boots in to the flashed rom.
Even trying a reflash doesnt show any signs of an older Rom being present on the phone memory..
One question about Mtty, when its said to use the ROM flasher i kinda assumed they ment the CustomRUU program. Am i right, or is there some build-in command to Flash a ROM within MTTY??
Click to expand...
Click to collapse
i had the same problem.... i send it back to repair... had a hardware damage. Luckily i got it for free...
I don´t know if you have exactly the same problem, but it looks like that.
LORDShadowMan said:
i had the same problem.... i send it back to repair... had a hardware damage. Luckily i got it for free...
I don´t know if you have exactly the same problem, but it looks like that.
Click to expand...
Click to collapse
Well lets hope not, because i got mine for 50euro secondhanded, warenty is expired and im really not keen on spending more money on repair than what i paid for.
Have you tried to put another Radion on it?
dravik said:
Have you tried to put another Radion on it?
Click to expand...
Click to collapse
Actually yes i did and it doesnt make any difference.
The weird thing is that even after succesfull flashing both Harspl and Rom never seems to stay on the phone memory but the Radio get updated.
jvanzeijst said:
Actually yes i did and it doesnt make any difference.
The weird thing is that even after succesfull flashing both Harspl and Rom never seems to stay on the phone memory but the Radio get updated.
Click to expand...
Click to collapse
I had a problem with my phone where I did mtty, but forgot to rename the diamimg.nbh file on my phone. So it wouldn't get passed the bootscreen.
My solution was to connect the phone to the usb, hold down the up arrow(I think it was the up arrow) and soft-reset. It came up with those 3/4 color blocks and said "usb" at the bottom. I then used the official htc ruu(also didn't show the current rom on it) to flash the normal htc rom onto it and it worked. Then I just did the normal procedure to get the custom rom on again.
So are you trying to flash the original HTC rom onto it, or a custom rom? Cause if it's a custom ROM, maybe it's just the radio, not the actual OS?
moreph34r said:
I had a problem with my phone where I did mtty, but forgot to rename the diamimg.nbh file on my phone. So it wouldn't get passed the bootscreen.
My solution was to connect the phone to the usb, hold down the up arrow(I think it was the up arrow) and soft-reset. It came up with those 3/4 color blocks and said "usb" at the bottom. I then used the official htc ruu(also didn't show the current rom on it) to flash the normal htc rom onto it and it worked. Then I just did the normal procedure to get the custom rom on again.
So are you trying to flash the original HTC rom onto it, or a custom rom? Cause if it's a custom ROM, maybe it's just the radio, not the actual OS?
Click to expand...
Click to collapse
I tried both custom and Stock Roms several times. After flashing the Stock roms i noticed that the radio version get updated, just no OS to boot!
Since the flashing sequence completes to 100%, i think its strange that the os doent seemed to be copied at all. Is there a possibility that a bad SPL is causing the OS not to be found?? In the Bootloader it still says SPL v1.93 Olinex so i guess its still Hard spl'ed. But when i try connect the phone to pc by usb, it shows up as Qualcamm CDMA device then later changes to HTC...
The Phone is not a CDMA version but i think maybe there is a change that somehow a CDMA SPL accidentlly got uploaded to it. This supposed to cause a phone to brick.
Many thanx for trying to help!
jvanzeijst said:
I tried both custom and Stock Roms several times. After flashing the Stock roms i noticed that the radio version get updated, just no OS to boot!
Since the flashing sequence completes to 100%, i think its strange that the os doent seemed to be copied at all. Is there a possibility that a bad SPL is causing the OS not to be found?? In the Bootloader it still says SPL v1.93 Olinex so i guess its still Hard spl'ed. But when i try connect the phone to pc by usb, it shows up as Qualcamm CDMA device then later changes to HTC...
The Phone is not a CDMA version but i think maybe there is a change that somehow a CDMA SPL accidentlly got uploaded to it. This supposed to cause a phone to brick.
Many thanx for trying to help!
Click to expand...
Click to collapse
Ok, maybe you can try from scratch to re-flash everything?
You should still be able to HardSPL, by doing the soft-reset+vol down thing.
I'd suggest getting the HardSPL from here(I only used it once, but I know it worked for me):
http://forum.xda-developers.com/showthread.php?t=416211
Hopefully that alone is what you need but if it isn't, you should then be able to flash a radio onto the phone(there's a link in that thread too) and then the stock HTC rom(I think the stock would have a better chance than anything else)
All of those flashes should be possible by doing the soft-reset+vol down and then using the RUU. Do you know how to use the RUU to flash a HardSPL, Radio and then OS separately?
you should probably try a full mtty just before you flash the OS(just after you flash the radio) as well, do the set 14 0,task 28 and task 29 and then task 8
And regrading Windows picking up your phone as a CDMA, I can't remember what mine said, but I don't think you should worry much about what Windows thinks the phone is.
*Edit, you should follow the mtty guide here for the most part:
http://forum.xda-developers.com/showthread.php?t=540290
But the second last step(number 7) where you're required to remove the usb cable, soft-reset+vol down+back button to flash from the internal storage, you should keep the phone connected to the usb and soft-reset+vol down and flash the rom using the RUU
message deleted
moreph34r said:
Ok, maybe you can try from scratch to re-flash everything?
You should still be able to HardSPL, by doing the soft-reset+vol down thing.
I'd suggest getting the HardSPL from here(I only used it once, but I know it worked for me):
http://forum.xda-developers.com/showthread.php?t=416211
Hopefully that alone is what you need but if it isn't, you should then be able to flash a radio onto the phone(there's a link in that thread too) and then the stock HTC rom(I think the stock would have a better chance than anything else)
All of those flashes should be possible by doing the soft-reset+vol down and then using the RUU. Do you know how to use the RUU to flash a HardSPL, Radio and then OS separately?
you should probably try a full mtty just before you flash the OS(just after you flash the radio) as well, do the set 14 0,task 28 and task 29 and then task 8
And regrading Windows picking up your phone as a CDMA, I can't remember what mine said, but I don't think you should worry much about what Windows thinks the phone is.
*Edit, you should follow the mtty guide here for the most part:
http://forum.xda-developers.com/showthread.php?t=540290
But the second last step(number 7) where you're required to remove the usb cable, soft-reset+vol down+back button to flash from the internal storage, you should keep the phone connected to the usb and soft-reset+vol down and flash the rom using the RUU
Click to expand...
Click to collapse
Allright i'll give it another try..
keeping my fingers crossed!
moreph34r said:
Ok, maybe you can try from scratch to re-flash everything?......
Click to expand...
Click to collapse
Ok i tried its flashing the Stock HTC NLD rom now aroun 42.. 43%, its slow but atleast still going. This is a big Rom tough.
Two questions:
1. Flashing the hardspl took some time to initiate the progression bar and then suddenly in the blink of an eye from 0 to 100%,
after flashing the hardspl file wich showed in RUU as olinex v 1.40, it still showed SPL.193 olinex on the bootloader.. .. is this common??
2. Is it even possible to downgrade a bootloader?? i would love to have olinex 1.40 back.. i used it before and it worked fine on many roms...i keep thinking my SPL is the problem.
Bye now the Rom flashing finished and it didn't help.. its still frozen.
here is the output from MTTY, may be its usefull:
----------------------------
Cmd>set 14 0
HTCST ÚÈÒHTCE
Cmd>task 28
Format start
Fill RSVD information for block 288 to 321
Storage start sector=0xFF40, total sector=0xB080
Storage start block=1054, total block=706
Total Bad Block in CE: 0
Erase physical block from 1344 to 2032
si backup: Erase physical block from 2032 to 2048
Format end
Cmd>task 29
Format BINFS start
Fill RSVD information for block 288 to 321
CE start sector=0x14, total sector of CE and TFAT=0x14
CE start start block=321, total block=1727
Write 0xFF start page=0x5040, total page=0x1AFC0
Format BINFS end
Cmd>task 8
-------------------------------------
,thanx any way
Did you use the corresponding stockRom (the one with the corresponding spl i mean):
_QMR_RUU_Diamond_HTC_NLD_1.93.404.1_Radio_Signed_Diamond_52.29.25.12_1.00.25.05_Ship
Just in case you didn't, you can find it over here:
http://wiki.xda-developers.com/index.php?pagename=Diamond_Upgrades
Yes i did try, didnt work for me..
i kinda lose hope now.
Losing a phone sucks, first lost my iphone3g then bought this cheap as a replacement for the remaining contract, And now i really regrets that i tried restoring its stock rom,radio,spl since its really did brick the phone for good..
thanks for all the people that tried to help but i'm not sure if its fixable....
So thanx anyway..
yours,
Jeffrey
Mod. edit: not dev related, moved to general
gl though

Problem with HTC Kaiser Tytn II - please help...

So my problem is - I put android on my htc tytn II and it worked (well kinda) but anyway I decided to switch back to Windows Mobile...
I installed 1.27.x.x radio , found a Windows Mobile 6 ROM and put (Like in the instructions ) Kaisimg.nbh(renamed from ruu_signed.nbh) and Kaisdiag.nbh to my SD card and then started flashing... It flashed smth,rebooted automatically and started booting android again...
Then I hold again camera button + power+ reset and since then when I put EVERY .nbh file on my sd card and try to flash it it STUCK on "Loading.." If I try to flash it with USB It stays at 0%.
The only exeption is if I try to flash from USB the rom that I tried to flash before from my sd card.. then it starts 0%..1% and reboot the phone...
P.S: Please help me...I think my device is not Broken but I dont know what should I do to fix it...
To flash back to WM from android put your kaiser into bootloader (multi colored screen) Then connect to usb. Download any WM build that is recent (I suggest Phoenix 3 for this, you can flash whatever you want later). After you download it open and run the included RUU that came with it and it will flash it on there.
hmm, I also had experienced the similar problem on my 1st time flashing back to WinMo.
When you are trying to flash via USB cable and the process stopped at 1% I guess there is also a message about "Invalid vender ID" right?
and if the text in your bootloader (tricolor screen) doesn't mention anything about hard such as "3.29.0000" (not "3.29.hard")
then
you've lost your hard SPL that's why you cant flash any .nbh to your phone.
I had managed to solve this problem by flashing stock WM rom for kaiser. The rom also has to be suitable for your phone, I mean if your kaiser is originally from France, then use French kaiser stock rom. Or if you are using AT&T Tilt use kaiser cingular stock rom.
you can find the list of shipped roms for kaiser here :
http://shipped-roms.com/shipped/Kaiser/
If you still have the "invalid vender ID" error message, try another stock ROM.
Thanks man you're my hero! I though I lost my phone.. anyway i bought new one - Nokia 2730 Classic but Ill sell the kaiser...
Thanks Anyway ... you're god!
Have the same problem...
Firstly, I'd like to point that the reason for the hard SPL getting overwritten by an original SPL is NOT HAVING UPDATED HARDSPL to a newer version that prevents accidental overwrite. This is instructed in the previous steps before actually installing Android. That was my mistake (I had HardSPL 1.0 OliPof), and now I can't flash no rom to my Kaiser (which thankfully works quite well in Android).
What happens (please correct me if I'm wrong) is that "KAISDIAG.NBH" is a modified, standalone hardSPL that will flash to the phone the SPL that comes with the "KAISIMG.NBH" you put in your SD card with "KAISDIAG.NBH"). In my case, I used the WinMo 6.1 spanish version 3.29.412.0, which, resulted in my phone being flashed with the original SPL 3.29.
Now, it seems many users have fixed this locating the correct stock rom and flashing it in their Kaisers. But to others, like myself, nothing seems to work. I believe that this is because we not only need a stock rom for our specific Kaiser model, but also it has to be compatible with the SPL that accidentally got installed in the phone. The problem is what if such rom doesn't even exists?
I'm really thankfull for all I learned by reading the forums (and from my mistakes ) and I know I'm in no position to make requests, but here goes what I think could help the users like myself to fix this, if posible:
1) Guide to identify what model of Kaiser we have (maybe it's already there, I just couldn't find it)
2) Complete list (or lists) of stock roms (There are some around, those are easy to find I think, but it doesn't hurt to share different sources)
3) Something like a JumpSPL for Android would be more than awesome...
Thanks in advance to everybody, sorry for my own stupidity . Any idea or help would be much appreciated,
Daniel
hmm, I'm not sure if it has to be compatible with the SPL.
In my case, I was flashing a very old WWE stock rom which has original SPL 1.56.
I also had been very desperate because any stock rom I found seems doesn't work and I even didn't know where originally my kaiser came from because I get it from my uncle. So I tried to flash any WWE stock rom I could found but nothing works. I read from Wikipedia that based on my phone model (Kais100), this model was only sold as AT&T tilt for US. But the problem is my phone is HTC branded, not AT&T tilt. Well, based on this information I also tried to flash some cingular stock rom but the result was just the same.
After contacting HTC Customer care, I know more info about my phone. They told me that based on my phone product ID, my kaiser was originally shipped for US, but unfortunately they can't provide me stock rom for my phone model. So I searched myself but this time I had better objective : to search HTC branded rom but for US.
finally, after days of search. I've found the rom that is suitable for my phone. Its called HTC WWE Brightpoint US which has original SPL 3.29 at the bottom of the list on the website I told you on my previous post.
few weeks ago I also accidentally overwrite my HardSPL again, but this time I did it with the stock ROM which has original SPL 3.29. But this problem also solved by flashing the stock ROM I've found before via USB cable.
So, I guess it has nothing to do with spl version.
Keep tying don't give up.
Update: Step 1 completed! YAY
Using the serial number and some obscure google searching, I came to the conclusion my KAIS130 is australian. Cheers, mate!
I verified this by being able to download stock roms from the australian HTC site with my Kaiser serial number. But at the moment of writing this, have downloaded two roms and no luck yet. 5 minutes remaining for the third one... Wish me luck...
Daniel.
Well... Now what?
Tried all four rom-like thingies I could download on the HTC page, all of them returning error 294...
Now what? try to somehow extract the .nbhs from the exes and and use customRUU.exe? Try to flash from SD card?
Please help... Any ideas... I really want to get rid from that original SPL3.29.0000 It's evil!!! I think it won't never let me flash again.
Thanks,
Daniel
cuartetoraro said:
Tried all four rom-like thingies I could download on the HTC page, all of them returning error 294...
Now what? try to somehow extract the .nbhs from the exes and and use customRUU.exe? Try to flash from SD card?
Please help... Any ideas... I really want to get rid from that original SPL3.29.0000 It's evil!!! I think it won't never let me flash again.
Thanks,
Daniel
Click to expand...
Click to collapse
sorry to hear that..
well, extract the .nbh from exe and flash it via sd card is the method that made me overwrite my hard SPL in the first place.
hmm, did your phone comes with operator brand, such as three or something?
-Rif- said:
sorry to hear that..
hmm, did your phone comes with operator brand, such as three or something?
Click to expand...
Click to collapse
No, it's HTC unbranded. Now, something strange here: the label behind the battery has the serial number: HT830GB06075 and the P/N (guess it's part number) :99HCY194-00, but to the left of the camera, another label with the part number: 36H00563-00M and below says DATE:061107(TB02)/US.
I don't know if that's normal, but it caught my atention because my phone seems to have been dissasembled (little label over screw is teared). Maybe my Kaiser isn't Australian after all...

Categories

Resources