Related
I have an issue that many seem to have reported, but I cant seem to find the "fix" for the life of me. Basically I had stock JF6, enabled USB debugging, copied the update.zip to internal SD card, and used adb to reboot to recovery mode and applied it from there.
Since then, it locks up within 10 seconds of the first appearance of the home screen, and I get about 5 force close popups prior to that. No amount of battery pulling and rebooting changes this. It is no longer recognized or able to be commanded by adb, and I have one of the phones where the Vol button + Pwr button combo does not work to get into recovery mode.
I literally have no options left but to throw this POS away, that I can see.. please help. Thanks
http://forum.xda-developers.com/showthread.php?t=731989
There's the link for Odin one click, it is possible that your drivers are hosed. When you plug your phone in does it charge, does your computer make that little bing sound when you plug to charge? Don't panick, these phones are almost impossible to brick.
Download and install the drivers from the OP of this thread, you will see several methods of getting your phone into download mode. Open Odin first, it is already preloaded with the stock JF6 for your phone and will get you back to stock. You do not need to throw it away. Keep your phone unplugged when you start up Odin, pull out your battery, then put the battery back in, hold the volume up and down buttons only not power, while the volume buttons are pressed plug in your usb and you should get into download (you should see the Android shovelling and it will say do not turn off target) and Odin should show your device and then hit start and let it do it's thing, it should take about 5 to 10 minutes to work.
Also read the Odin thread, people have been in worse situations than you and got it out of a brick state. This should work. Good Luck.
Help !!!!!!!!!!!!!!!!!!!!!!!!!!
hmy captivate died after flashing Axura using clockwork
now I can not boot up the phone, unplug the battery for 15 Min and put it back but still the same can not boot up the phone....
please help
You need to figure out a way to get into Download Mode, use ODIN, and flash back to JF6. Once you have JF6 running, you can flash whatever rom you want again.
If you search, you'll see a bunch of posts on the different methods to get to Download Mode.
Goodluck.
Yes, I know if I get download mode I can flash whatever rom, but the problem is that the phone completely dead nothing shown in the screen, I have tried the following
1- try the combination of Vol down + Power
2- try the combination of Vol up + Vol Down + Power
3- try Vol down and then connect USB
4- try Vol down + Vol Up and then connect USB
all these while opening ODIN
also I tried this on both windows 7, and windows XP.
do you have any other suggestions to do.
please help
Still have the problem, need heeeeeeeeeeeeeeeeeeelp please
How did it exactly die? It'd be useful for people who may know a solution. I've heard of JIG a few times.
you get the little home lights on the bottom of the phone to light up at least?
Also.. does the computer recognize the device?
If not and it's completely black screen and you don't even feel it vibrate while booting? Its toast.
But.. try doing the battery/sim card pull - hold down both volume buttons plug in the USB and jam in the batter and see if that works.
Or.. to the ATT warranty center you shall go.
I was flashing Axura rom using clockwork recovery, and after complete the installation and start reboot this back screen comes on, now not booting at all
Odin not recognize the phone, or even the computer does not detect any connected device,
I tried pull the battery, wait for 15 min then connect the USB, hold vol up, down and power keys then put the battery back while holding these three keys nothing happen, the screen still black and the computer not detect it.
I tired all ways but nothing works with me.
Now I think it is complete died, Even I tried the hair dryer trick but nothing works.
some posts talk about JIG
How this JIG works and how to do it?
up for heeeeeeeeeeeeeeeeeelp
hzeid said:
I was flashing Axura rom using clockwork recovery, and after complete the installation and start reboot this back screen comes on, now not booting at all
Odin not recognize the phone, or even the computer does not detect any connected device,
I tried pull the battery, wait for 15 min then connect the USB, hold vol up, down and power keys then put the battery back while holding these three keys nothing happen, the screen still black and the computer not detect it.
I tired all ways but nothing works with me.
Now I think it is complete died, Even I tried the hair dryer trick but nothing works.
some posts talk about JIG
How this JIG works and how to do it?
Click to expand...
Click to collapse
USB Jig will trigger the phone into Download mode.
******Soldering Required******
http://forum.xda-developers.com/showthread.php?t=819551
****Solderless version****
http://forum.xda-developers.com/showthread.php?t=841512
I followed JIG solution, connect resistants of 301K on pin 4,5 on mini usb head, nothing works still black screen, no at&t log nothing
help any new suggestion
try charging the phone for a few hours, if possible try a different battery.
also you may be in download mode with a black screen. i had a bad crash once from too much overclock or a corrupted kernel flash with the manhatten project 1.6ghz kernel. it corrupted the image files for bootup and download mode, my startup screen was garbage and had a black screen for download mode. but download mode still worked. start odin, it may still show device connected.
I did connect the JIG for 10 sec then disconnect it, then connect the phone to the computer while ODIN open, but nothing happen the computer still not detecting the phone, also the screen still black, it does not even any sign of responding except it get heated when connect it to charger.
guys as posted in other thread, will reward 75 US$ for who will help me getting my phone back to life
if you got the phone through at&t, you might as well just go exchange it for a new one. the people there won't be able to determine if you've voided your warranty if they can't boot your phone either.
sorry I did not got the phone from AT&T, I bought it from Ebay so I can not send it back to them
So I was attempting to flash back to stock with Odin (I was using Assonance 5.2). I turned the phone off, then while holding the volume buttons plugged in the USB like normal. Then Odin said added the phone, then I hit start. And it seemed like it was working just fine, then all of a sudden the screen on the phone turned red. Then the status bar on Odin stopped moving completely (stayed for awhile). So I think I made the next big mistake of just disconnecting the USB and taking out the battery. So now the phone won't turn on. So I'm not sure I hard bricked the phone or what? Anyone have any idea? Thanks!
I've plugged the phone into the outlet charger, still nothing happens. This happened like maybe 15 min ago. No action when plugged in the computer or charger. Can't even boot into recovery I don't think. the power button was giving me some trouble earlier today. whenever I was trying to wake the phone up, it seemed to take a few clicks of the power button to wake the phone. This happened only after I flashed Assonance 2.5, so I wanted to flash to an earlier version of the rom. thanks!
What you want to do is get into Download Mode, and flash with Odin One-Click JF6 to get your phone working again..
Have you tried all the various button combos to get into Download Mode? .
If the button combos don't work, you can always try to build/buy a JIG which will force your phone into Download if it's still possible on your phone.
I've tried to get into download mode, but can't seem to do it. I've tried holding the volume up and down button then plugging in the usb (which didn't work). then i tried the taking the battery out, then holding the volume up and down button and power button, then plugging in the usb, then reinserting the battery, then taking my hand off the power button (which didn't work). what is the JIG method?
edit. ok i have no clue wtf just happened, but i am currently in download mode using odin and flashing back to stock.....this is just too weird.....sooo any rom suggestions?
Look in my signature for an example of a JIG.
norcal einstein said:
Look in my signature for an example of a JIG.
Click to expand...
Click to collapse
cool i'm actually gonna go ahead and get one this things......JUST in case of future screw ups that don't have a happy ending
i clicked on the link but it won't let me go the page. below is the message it gave me.
marefin, you do not have permission to access this page. This could be due to one of several reasons:
Your user account may not have sufficient privileges to access this page. Are you trying to edit someone else's post, access administrative features or some other privileged system?
If you are trying to post, the administrator may have disabled your account, or it may be awaiting activation.
marefin said:
cool i'm actually gonna go ahead and get one this things......JUST in case of future screw ups that don't have a happy ending
Click to expand...
Click to collapse
Definitely a great idea having the jig. Nor cal can attest to the late night save that jig provided me.
Sent from my SGH-T959D using XDA App
When I tried to disable the voodoo lagfix my phone froze, after about 20 minutes i decided to pull the battery and now the phone freezes when trying to boot and even after plugging in the charger, it freezes on the battery load symbol. Unfortunately, the 3 button way to get to the recovery menu doesn't work. help me please??
I'm having the same problem - phone just hung on the kernel load screen (firebird 2) after trying to shut off lagfix - although I can get to a red recovery mode menu. Not that it's helping at this time. It would be nice if I could recover without a clean wipe of the phone.
Anyone have any ideas. I'll be scouring the threads...
You could try making a jig and flashing to stock http://forum.xda-developers.com/showthread.php?t=841512
how are you getting to the red recovery menu?
i have the same kernel and i'm running the firefly 1.5 rom
I can't boot into anything and the only solution i have so far is to make a jig or buy one and not have a phone for a little bit, which is going to suck..
I've tried the following combinations, just because I know people are going to ask.
1. take out battery, sim, etc.
2. leave out for about 15 seconds
3. plug in the battery, plug in usb and hold two volume buttons-> freezes while trying to load battery status
3.b same precedure as above except plug in usb first hold volume buttons then battery-> still frozen
3.c hold volume buttons, battery, then power button, let it cycle atleast 2 times and let go of power at att logo while holding the volume-> frozen at kernel loader
3.d same as above but with only one volume button at a time, both up and down-> no cigar
3.e all the precedures above while wildly pressing all the soft keys (home, search, yadda yadda) out of frustration -> thinking, gosh i'm screwed
did i miss out any secret other combinations or methods known to work?
I'd really like to do this without hardware, but making a jig kinda sounds like a fun project and i do have a soldering iron in storage somewhere...
xsamxoxo said:
how are you getting to the red recovery menu?
i have the same kernel and i'm running the firefly 1.5 rom
I can't boot into anything and the only solution i have so far is to make a jig or buy one and not have a phone for a little bit, which is going to suck..
I've tried the following combinations, just because I know people are going to ask.
1. take out battery, sim, etc.
2. leave out for about 15 seconds
3. plug in the battery, plug in usb and hold two volume buttons-> freezes while trying to load battery status
3.b same precedure as above except plug in usb first hold volume buttons then battery-> still frozen
3.c hold volume buttons, battery, then power button, let it cycle atleast 2 times and let go of power at att logo while holding the volume-> frozen at kernel loader
3.d same as above but with only one volume button at a time, both up and down-> no cigar
3.e all the precedures above while wildly pressing all the soft keys (home, search, yadda yadda) out of frustration -> thinking, gosh i'm screwed
did i miss out any secret other combinations or methods known to work?
Click to expand...
Click to collapse
I'm afraid not. This happened to someone I know and they told samsung the OTA update bricked it and AFAIK they fixed it for free. They never tried using a jig though, so if you don't want to wait to replace it or anything you could try a jig since it might work and the parts are pretty easy to get (and if you'd be replacing the phone, a jig is ALWAYS good to have anyway)
Just another note to throw in there, the computer recognizes the phone, but strangely my computer freezes while trying to read the media storage drives. I can't tell if the internal sd is mounted because of the ever-lasting wait but i'm almost positive its not.
Do adb commands work?
Sent from my SGH-I897 using XDA App
Thnikk said:
Do adb commands work?
Sent from my SGH-I897 using XDA App
Click to expand...
Click to collapse
nope, it says "error device is offline"
You could try ... when the phone is booting and trying to catch it before it freezes is spam the heck out of the command adb reboot download then after hitting the enter button hit the up arrow and keep repeating until either the phone a) hopefully goes into download mode or b) freezes and throws the error.
Who knows.. might get lucky.
avgjoegeek said:
You could try ... when the phone is booting and trying to catch it before it freezes is spam the heck out of the command adb reboot download then after hitting the enter button hit the up arrow and keep repeating until either the phone a) hopefully goes into download mode or b) freezes and throws the error.
Who knows.. might get lucky.
Click to expand...
Click to collapse
it connects even though the phone is frozen. I'm heading over to "The Shack" pretty soon and just making a jig.
Thanks for all your help everyone.
Edit: Just confirming that with much dedication and a steady hand I finally have my captivate up and running with the help of the resistors. I also flashed the 3 button fix stock rom.
Well, I kept trying the least invasive methods first. Tried to reflash Firebird. Then went adb and such. In the end, it was pretty clear that it had hung at the lagfix correction, and I was dealing with a file system error. I was eventually able to get into download mode. The hardest discovery was finding that I had gotten the wrong drivers from samsung. The ones in the [stock rom] odin master clear page were what I should have been using. When I loaded those, the computer recognized that I had a phone and not a "serial gadget" and then I knew I was close. Odin finally saw the phone, and a couple tries at "light" re-stocking failed at file analysis, so I did the repartition (aha, file system error), and it shot through the whole process and I had my phone back and flashed to Serendipity in about 20 minutes.
But I would like to know about the red menu. That was unexpected (blue for standard, green for cwm).
No need for a jig. I had access to some phone functions, most importantly, download mode.
Okay I was using odin one click it was at rebooting device after it completed pushing stock onto the phone thats when I discounted the usb.... should have waited two secs I know but now the phone doesn't seem to get past the att world phone screen keeps looping over and over I have tried all the key combos different times and ways, vol up and down being held doesn't get to download mode the screen remains black plunging in seems to get to charge mode where even plunging into the wall charger it loops trying to calculate the battery status... any method I haven't tried... I did get it to boot once full and was usable didn't think to redo odin at the time and restarted back to this mess...tried three different jigs using the 100k 5% X3 even through its not a full brick due to the button combos gotten no where. Please Help
Search the forum to build a jig in order to get into download mode. Or you may need to buy one just in case in the future.
http://cgi.ebay.com/ws/eBayISAPI.dl...69977&ssPageName=STRK:MESELX:IT#ht_623wt_1139
Try this:
Open Odin and plug your cable into your computer but not your phone yet
Pull battery on phone and put it back in
Hold both volume buttons down and then plug your phone in
It should go into download made and you can reflash the stock ROM
Can anyone please help, i have the exact same problem. No matter how i try to enter download mode, it just gives me a charging sign and when i start my phone, it goes into an infinite boot loop.
Try this:
1. Remove battery from phone, SIM card and MicroSD card (if you have one)
2. Wait AT LEAST 10 seconds with your phone in this state
3. Hold Volume Up/Down, don't let go
4. While holding the volume keys, insert the battery
If this worked, you should be in Download Mode almost instantly.
There are a lot of key combos for Download Mode, this is just one of them. If all the button combos don't work, you need to build/buy a JIG to force your phone into Download Mode.
norcal einstein said:
Try this:
1. Remove battery from phone, SIM card and MicroSD card (if you have one)
2. Wait AT LEAST 10 seconds with your phone in this state
3. Hold Volume Up/Down, don't let go
4. While holding the volume keys, insert the battery
If this worked, you should be in Download Mode almost instantly.
There are a lot of key combos for Download Mode, this is just one of them. If all the button combos don't work, you need to build/buy a JIG to force your phone into Download Mode.
Click to expand...
Click to collapse
Ahah Thats the same exact steps I was able to get the phone to boot that one time instead of the up down I was still attempting it to get past the loop holding the power button instead using those steps, if I had know it would have been one of the only times I would see it in there I would have pushed it to download with adb though...
can't test getting it to download mode now took it back fit the description of the standing on/off issue with the device still honored by warranty. And I wouldn't have posted without searching everywhere to make a jig, I made three of them though I noticed it still didn't get to download mode. I made sure that the last two jigs were done correct. Think that when it was disconnected from odin it wasn't done finalizing after the stock push gah >,< live and learn and do something else to the cappies XD.
Thanks for the link placing an order just in-case ~whistles looking around then side to side pushes another rom~ lalala
To offer my own advice if it ever happens again, what I've been able to do is:
1. Pull the battery out
2. Put it back in
3. Open Odin
4. Hold Both Volume Buttons (without holding the power button)
5. Plug the phone back in
It went immediately into download mode for me, Odin managed to time out several times while I was trying to flash a co-worker's Captivate to the official Froyo leak. One of those times I couldn't even get the phone to come up with any screen. I really do think this thing cannot be bricked.
BeowulfShaeffer said:
That has been my experience so far, too. I've "bricked" twice, once with an "all black" screen, and once with the phone-!-computer screen. I've yet to need a jig, though I thought I may have needed it last night when I got the "all black" screen.
Keep trying the different button press methods to get into download mode. It took me 4 attempts to get from "all black" to "phone-!-computer" to a happy robot digging away.
Click to expand...
Click to collapse
if you are out of luck, you may have to build a jig or buy one online.
http://cgi.ebay.com/ws/eBayISAPI.dl...69977&ssPageName=STRK:MESELX:IT#ht_623wt_1139
Ive used odin before changing roms and have gotten to download mode with combos on my last cappy before that night (dramatic music) en ways..
did some more digging on this bad ass info and learning community "XDA" hehe as to how it got the way it did, I found out I was updated with the new patch when I sent it for screen change to this shop, so...using odin one click with this creates a hang time to where it looked like it was finished after pushing jh6 (which was totally off should have used odin 3 and pushed jh2 then clockwork update to jh7) so thats when I disconnected (second noob mistake of the situation) basically blowing the finalization out and key combs for recovery and download mode. and im guessing the jig was made wrong too at this point >,<.
Oh
wmason92 said:
Can anyone please help, i have the exact same problem. No matter how i try to enter download mode, it just gives me a charging sign and when i start my phone, it goes into an infinite boot loop.
Click to expand...
Click to collapse
If you cant get your jig to work take it in to warranty (if your water inicators are sound and no physical damage) and say its power cycling on off at random times (which is true.. ) and it did it when you were sync to mini kies, did it an hour after the OP heh good luck
and I have yet to see the infamous yellow pc sign >,> <,< it can stay on the yellow brick road... thanks for the responses btw
Well the same thing happened to me and i got stuck with in an unlimited boot animation. Ive trying everything key combo possible and ive tried a jig but it just makes it reboot, and yes im sure im touching the right pins. If anybody can help with this dilemma i would really appreciate it. I want to return with warranty but my phone has a custom boot animation so im sure att probably wont accept it if they notice it.
wmason92 said:
Well the same thing happened to me and i got stuck with in an unlimited boot animation. Ive trying everything key combo possible and ive tried a jig but it just makes it reboot, and yes im sure im touching the right pins. If anybody can help with this dilemma i would really appreciate it. I want to return with warranty but my phone has a custom boot animation so im sure att probably wont accept it if they notice it.
Click to expand...
Click to collapse
Purchase jig from ebay, or google and try igo jig.
If your phone is turning on with jig you are not touching the right prongs. I know, I know it is not easy, but unless it if touching just right, it can turn your phone on.
Holy ******** i got it to download mode! For some reason i kept touching the same pins and nothing would happen. After about readjusting for about 5mn it finally worked!!!!
It has to be just so. Happy to hear
Wait, now its in download mode but my computer keeps saying usb device not recognized.
wmason92 said:
Wait, now its in download mode but my computer keeps saying usb device not recognized.
Click to expand...
Click to collapse
That happens try a different usb port or just borrow someone else computer, I used my networking classes computer my laptop was doing the same thing when I was change roms.
Changed the title to fit the issue, this is not a soft brick this is a boot brick that can affect the charge indicator in power off state as well. So whats the difference the soft brick is when you flash a rom incorrectly and you get the att world screen constantly staying on, the key combinations still work when the phone is like this.. in the case with a boot brick the att screen cycles over and over and the jig may or may not work I haven't been able to fully test it here in this state I have seen a packager attempt to finish once on the recent one but all the key combos I could find didn't function my noob guess is the phone forgot how to ride a bike (meaning is hasn't connected keys to recovery that was being flashed or hardware to there states without being booted normally) ultimate fix is if its in warranty (meaning no physical damage or water) take it back for power on off. the soft brick i've seen before and have fixed with odin 2-3 three times, and ive seen a blown kernel type too where keys and odin fix up like new.
wmason92 said:
Well the same thing happened to me and i got stuck with in an unlimited boot animation. Ive trying everything key combo possible and ive tried a jig but it just makes it reboot, and yes im sure im touching the right pins. If anybody can help with this dilemma i would really appreciate it. I want to return with warranty but my phone has a custom boot animation so im sure att probably wont accept it if they notice it.
Click to expand...
Click to collapse
I have the same thing happening to me. Att boot screen, then it loops on the ROM logo, over and over. I get 1 vibrate then 2 following also. I purchased a Jig on ebay but it just keeps rebooting the phone, doesn't get it into download mode.
glaze76 said:
I purchased a Jig on ebay but it just keeps rebooting the phone, doesn't get it into download mode.
Click to expand...
Click to collapse
Very odd - I've never heard of that with a jig.
glaze76 said:
I have the same thing happening to me. Att boot screen, then it loops on the ROM logo, over and over. I get 1 vibrate then 2 following also. I purchased a Jig on ebay but it just keeps rebooting the phone, doesn't get it into download mode.
Click to expand...
Click to collapse
Have a link to which one you have? It sounds like the solder points on the jig were a little weak. This can happen if they aren't good welds. If you want give one of mine a shot. I'll refund you if it reboots your phone...
Buy one HERE...
I had a boot brick happen to me just the other day. I was running Andromeda 1.1 with stock kernel & modem, and tried to tinker with swapping the AT&T boot screen using connexion2005's video on the subject (NOT insinuating any blame at all, his videos are fantastic).
I tested it successfully the first time, then flashed back the i9000_param_lfs, and pushed a new image to the device again (everything was exactly the same, with the exception of the boot_screen.bat script not making the phone ask for superuser approval while pushing the new logo_ATNT), and everything looked ok.
Reboot device, and...boink.
Black screen, no image at all on power on, only charging screen when usb cable connected. ADB, nothing. 3 button, nothing. Vol up+down, remove battery, insert usb cable, do hokey pokey, nothing. 5 attempts at the 100k resistor jig, for hours, nothing. No download, no recovery. Seems like the phone was toast.
Strange how I had just done this successfully earlier in the day, to now having it completely hard brick this phone.
I ended up taking the phone back to a local warranty center, and they swapped it (1008) for a 1010 (gps works fantastic on this one, btw)...I just hope there's no bill coming if they find out it was rooted and flashed. *crosses fingers and uses any and all karma*
Any ideas what happened? Did I scramble this things boot loader? I've heard how hard it is to fully brick this phone, and looks like I succeeded. How lucky.
I'd just like to know what went wrong so when I (or anyone else) root and flash next time, the chances of this happening are reduced (or better understood).
Thanks