Database Develop

Mobile stream & a kaiser help please

Hi all,this is my first post here. I have just bought a T mobile (uk) MDA vario III or a kaiser. running windows mobile 6 pro (CE OS 5.2.1620) build 18125.0.4.2
I have a HSDPA full data plan
im trying to get it up and running my macbook pro via USB, i have successfully tethered using bluetooth pan but find the speeds painfully slow.
I have also managed to tether it using WMwifirouter (which is an excellent bit of software) and the speeds are great, which is my best solution so far. but im thinking i can still get faster speeds
however i came across mobile streams USB modem which has been recently updated to support the new version of osx..
i have followed all the instructions and installed the modem scripts to the mac and installed the software and enabled it on the kaiser
however when i connect it all up the mac keeps giving the message" no carrier found"
also i have noticed the kaiser does not seems to activate the internet connection (HSDPA) the icon just stays the same
i have checked and double checked all my user and password setting and all the other options.
i have also been emailing back and forth mobile stream to se if these a solution.
just wondered if you guys could help me out? my log from the mac is below
Thanks
Richard
Jun 2 21:09:12 Richards-Mac pppd[563]: pppd 2.4.2 (Apple version
314) started by root, uid 501
Jun 2 21:09:13 Richards-Mac ccl[564]: Script v1.30wm
Jun 2 21:09:13 Richards-Mac ccl[564]: Configuring the serial port
Jun 2 21:09:13 Richards-Mac ccl[564]: Checking the phone is
responding
Jun 2 21:09:13 Richards-Mac ccl[564]: CCLWrite : AT\13
Jun 2 21:09:13 Richards-Mac ccl[564]: CCLMatched : OK\13\10
Jun 2 21:09:13 Richards-Mac ccl[564]: Initializing the phone
Jun 2 21:09:13 Richards-Mac ccl[564]: CCLWrite : AT&F0E0V1S0=0\13
Jun 2 21:09:13 Richards-Mac ccl[564]: CCLMatched : OK\13\10
Jun 2 21:09:26 Richards-Mac ccl[564]: CCLWrite : AT
+CGDCONT=1,"IP","general.t-mobile.uk"\13
Jun 2 21:09:26 Richards-Mac ccl[564]: CCLMatched : OK\13\10
Jun 2 21:09:26 Richards-Mac ccl[564]: Dialing *99#
Jun 2 21:09:26 Richards-Mac ccl[564]: CCLWrite : ATD*99#\13
Jun 2 21:09:26 Richards-Mac ccl[564]: CCLMatched : NO CARRIER\13\10
Jun 2 21:09:26 Richards-Mac ccl[564]: CCLExit: -6021 (No carrier.)
Jun 2 21:09:26 Richards-Mac pppd[563]: Connect script failed

VPN problems

I have some problems using VPN on Gingerbread.
I upgraded my I9000 to a stock JVO with CF root. Now I noticed that I can no longer connect successfully to my VPN server. Before I was using I9000XXJPY and was working, but now it starts to connect and just stay with "Connecting..." for about 1min then drops.
Because I have access on the VPN server I can see the auth going ok and the VPN tunnel going up. I can even ping for couple of sec the VPN IP.
Here is the related server log:
May 31 12:17:05 server pptpd[17417]: CTRL: Client xxx.yyy.zzz.www control connection started
May 31 12:17:06 server pptpd[17417]: CTRL: Starting call (launching pppd, opening GRE)
May 31 12:17:06 server pppd[17418]: Plugin /usr/lib/pptpd/pptpd-logwtmp.so loaded.
May 31 12:17:06 server pppd[17418]: pptpd-logwtmp: $Version$
May 31 12:17:06 server pppd[17418]: pppd 2.4.4 started by root, uid 0
May 31 12:17:06 server pppd[17418]: Using interface ppp0
May 31 12:17:06 server pppd[17418]: Connect: ppp0 <--> /dev/pts/2
May 31 12:17:06 server pptpd[17417]: GRE: Bad checksum from pppd.
May 31 12:17:06 server pppd[17418]: MPPE 128-bit stateless compression enabled
May 31 12:17:07 server pppd[17418]: Cannot determine ethernet address for proxy ARP
May 31 12:17:07 server pppd[17418]: local IP address 10.10.50.1
May 31 12:17:07 server pppd[17418]: remote IP address 10.10.50.5
May 31 12:17:07 server pppd[17418]: pptpd-logwtmp.so ip-up ppp0 [email protected] xxx.yyy.zzz.www
May 31 12:17:47 server pppd[17418]: LCP terminated by peer (MPPE disabled)
May 31 12:17:47 server pppd[17418]: pptpd-logwtmp.so ip-down ppp0
May 31 12:17:47 server pppd[17418]: Connect time 0.7 minutes.
May 31 12:17:47 server pppd[17418]: Sent 2184 bytes, received 2526 bytes.
May 31 12:17:48 server pptpd[17417]: CTRL: EOF or bad error reading ctrl packet length.
May 31 12:17:48 server pptpd[17417]: CTRL: couldn't read packet header (exit)
May 31 12:17:48 server pptpd[17417]: CTRL: CTRL read failed
May 31 12:17:48 server pppd[17418]: Modem hangup
May 31 12:17:48 server pppd[17418]: Connection terminated.
May 31 12:17:48 server pppd[17418]: Exit.
May 31 12:17:48 server pptpd[17417]: CTRL: Client xxx.yyy.zzz.www control connection finished
Is there any way I could debug the pptp connection on the android? Anyone have VPN working on Gingerbread JVO or other versions? Any ideas what I could try?

Here is the related logcat from phone:
D/mtpd (13829): Waiting for control socket
D/mtpd (13829): Received 20 arguments
I/mtpd (13829): Using protocol pptp
I/mtpd (13829): Connecting to aaa.bbb.ccc.ddd port 1723
I/SProxy_mtpd(13820): got data from control socket: 20
I/mtpd (13829): Connection established (socket = 15)
D/mtpd (13829): Sending SCCRQ
D/mtpd (13829): Received SCCRP -> Sending OCRQ (local = 62032)
I/mtpd (13829): Tunnel established
D/mtpd (13829): Received OCRQ (remote = 4)
I/mtpd (13829): Session established
I/mtpd (13829): Creating PPPoX socket
I/mtpd (13829): Starting pppd (pppox = 16)
I/mtpd (13829): Pppd started (pid = 13830)
I/pppd (13830): Using PPPoX (socket = 16)
D/pppd (13830): using channel 21
D/Tethering( 482): ppp0 is not a tetherable iface, ignoring
I/pppd (13830): Using interface ppp0
I/pppd (13830): Connect: ppp0 <-->
I/pppd (13830): MPPE 128-bit stateless compression enabled
I/pppd (13830): local IP address 10.10.50.5
I/pppd (13830): remote IP address 10.10.50.1
I/pppd (13830): primary DNS address 8.8.8.8
I/pppd (13830): secondary DNS address 8.8.4.4
I/ip-up-vpn(13831): Traffic is now redirected to 10.10.50.1
E/VpnService(13820): onError()
E/VpnService(13820): java.io.IOException: Connecting timed out
E/VpnService(13820): at com.android.server.vpn.VpnService.waitUntilConnectedOrTimedout(VpnService.java:206)
E/VpnService(13820): at com.android.server.vpn.VpnService.onConnect(VpnService.java:136)
E/VpnService(13820): at com.android.server.vpn.VpnServiceBinder$2.run(VpnServiceBinder.java:117)
E/VpnService(13820): at java.lang.Thread.run(Thread.java:1019)
I/VpnService(13820): disconnecting VPN...
D/VpnSettings(13812): received connectivity: pptpVPN PPTP: connected? DISCONNECTING err=0
I/StatusBarManagerService( 482): ADD-pptpVPN PPTP VPN disconnected , 0x7f020001
I/SProxy_mtpd(13820): Stop VPN daemon: mtpd
I/pppd (13830): Terminating on signal 15
I/pppd (13830): Connect time 0.7 minutes.
I/pppd (13830): Sent 8174 bytes, received 0 bytes.
I/mtpd (13829): Received signal 15
I/mtpd (13829): Sending signal to pppd (pid = 13830)
E/pppd (13830): MPPE disabled
I/pppd (13830): Terminating on signal 15
I/pppd (13830): Connection terminated.
I/mtpd (13829): Mtpd is terminated (status = 6)

Nobody using VPN in Gingerbread? Any feedback would be appreciated.

rising the stakes
Ok, since nobody rush here, I will raise the stakes:
Who can help me to find a fix for this problem will win a 3 month VPN account to a VPN provider of my choice (lots of servers to use there).
If anyone have a android setup close to mine and it's VPN works, let me know.

Have u tried any other kernel or turning VPN encryption off. Also try 1Vpn app from the market
Sent from my GT-I9000 using XDA Premium App

Did you turn encryption OFF (uncheck) on your phone?
AFAIK, there is no mppe encryption support in the stock android firmware. Maybe your previous firmware included the module? Anyway, PPTP works fine for me with MPPE disabled, but not if I require it. Hope this helps...

I do get the same behavior with or without the mppe enabled. It doesn't looks like to be a encryption problem as I can see the log in successful on the server and even can ping the client IP after for couple of seconds. It looks like the VpnService does not see the connection being established and it just stops it after couple of seconds.

Never got VPN working successfully even in 2.2 and 2.2.1. It was able to connect to the VPN service (can't remember if I used PPTP or L2TP) but I was unable to browse any website or connect to anything on the internet.
I was told on some forum there's some bug in Android causing this. Anyways, doesn't sound identical to the issue you had but I thought I'd mention this.

Worked for me when using 2.2.1 JPY, both PPTP and L2TP. I suspect it's a VpnService problem rather then a pptp problem, so if anyone on 2.3.3 JVO or similar have VPN running ok, would appreciate if would send me on PM or attached here the VpnService.apk and .odex he run.

isn't it the same problem as posted on the android google code site:
http://code.google.com/p/android/issues/detail?id=4706

appears to still not be working in jvp.. no one seems to have it working with 3g on any phone with gingerbread.. it appears to work ok over wifi.. i also need i working in 3g in gb. .so i am staying on froyo for now.

anyone tether Hero to linux?

Hello,
Dual booting W7 and openSUSE 11.4. Hero running CM7 nightly 123. Wifi tether and barnacle apps work flawlessly with W7 but I can't get any connection with linux. In network manager it shows the network SSID with full signal strength. There is also a computer icon next to the signal strength icon that is not present on any of the other networks recognized (live in apartments). Anyone familiar with linux to help me tether in linux? Wireless or wired, I just need to get online.
Thanks for any and all help.

studdyhalllooser said:
Hello,
Dual booting W7 and openSUSE 11.4. Hero running CM7 nightly 123. Wifi tether and barnacle apps work flawlessly with W7 but I can't get any connection with linux. In network manager it shows the network SSID with full signal strength. There is also a computer icon next to the signal strength icon that is not present on any of the other networks recognized (live in apartments). Anyone familiar with linux to help me tether in linux? Wireless or wired, I just need to get online.
Thanks for any and all help.
Click to expand...
Click to collapse
I tether with my netbook (funtoo) many times. The computer pictures by the network is because network manager recognizes it as a devices and not a router. Can you do two things for me. First connect to the hero. Then open a terminal and past the output of the following commands
Code:
sudo ifconfig
Code:
sudo iwconfig
The point here is to see if you are getting a good ip address and if the dns/gateway info is correct.

i wonder if this will work on ubuntu usb works fine for me but wireless always disconects. if i could get wireless tether to work i would probably use ubuntu as my daily.

I cannot connect to it at all. It shows the rotary progress animation as if it is connecting and about 30 seconds later it quits.

studdyhalllooser said:
I cannot connect to it at all. It shows the rotary progress animation as if it is connecting and about 30 seconds later it quits.
Click to expand...
Click to collapse
Try enabling/disabling authentication in wireless tethering on your phone.
Also if that doesn't work you can try to force your laptop to connect to the network with
If your wireless network is wlan0 (you can check what your network connection is by running iwconfig first).
Code:
iwconfig wlan0 essid "g1thether"
Where g1tether is the essid that your phone is broadcasting.
After you do that check and see if the ifconfig and iwconfig output is and see if you can load up a website .

for me its kind of weird when i restart my computer from win7 and boot into ubu itll connect to the tether fine but after 10 minutes or so itll disconnect and i cant get it to reconnect

PHP:
[email protected]:~> su
Password:
linux-uy1d:/home/jonathon # ifconfig
eth0 Link encap:Ethernet HWaddr A4:BA:DB:D5:CC:84
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:44 Base address:0x2000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:101 errors:0 dropped:0 overruns:0 frame:0
TX packets:101 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:9807 (9.5 Kb) TX bytes:9807 (9.5 Kb)
wlan0 Link encap:Ethernet HWaddr 70:F1:A1:BD:C9:F5
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
linux-uy1d:/home/jonathon # iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
wlan0 IEEE 802.11bgn ESSID:off/any
Mode:Managed Access Point: Not-Associated Tx-Power=19 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
linux-uy1d:/home/jonathon # iwconfig wlan0 essid "barnacle"
linux-uy1d:/home/jonathon # iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
wlan0 IEEE 802.11bgn ESSID:"barnacle"
Mode:Managed Access Point: Not-Associated Tx-Power=19 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
linux-uy1d:/home/jonathon #

No luck so far. Any other ideas?
Thanks again for your help!

studdyhalllooser said:
No luck so far. Any other ideas?
Thanks again for your help!
Click to expand...
Click to collapse
Can you run
Code:
ifconfig wlan0
for me (run it after you do iwconfig wlan0 essid barnacle).
Just want to see what the ifconfig is.
Next thing to try is with network manager try to connect. Wait a few second-minute and then post up the /var/log/dmesg file for me. You can just copy and past or attach as a text file. You'll have to be root to read it.
We'll get this. I'm not sure why you guys are having trouble here. What version of wireless tether for root users are you running? I always run 1.6.

Shelnutt2 said:
Can you run
Code:
ifconfig wlan0
for me (run it after you do iwconfig wlan0 essid barnacle).
Just want to see what the ifconfig is.
Next thing to try is with network manager try to connect. Wait a few second-minute and then post up the /var/log/dmesg file for me. You can just copy and past or attach as a text file. You'll have to be root to read it.
We'll get this. I'm not sure why you guys are having trouble here. What version of wireless tether for root users are you running? I always run 1.6.
Click to expand...
Click to collapse
Ok. I was running barnacle for the previous tests. Wireless tether for root was version 2.0.2. I uninstalled it real quick and installed 1.6 so my SSID changed back to G1Tether for this test. Here are my results
PHP:
[email protected]:~> su
Password:
linux-uy1d:/home/jonathon # iwconfig wlan0 essid G1Tether
linux-uy1d:/home/jonathon # ifconfig wlan0
wlan0 Link encap:Ethernet HWaddr 70:F1:A1:BD:C9:F5
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
linux-uy1d:/home/jonathon #
For the file you asked about; I cannot find it when browsing the file manager so I opened up the terminal in that location under root. Then used the "ls" command to show the contents of that folder. I cannot find the file you are asking about. Am I doing this correctly? I do not know many terminal commands.
PHP:
[email protected]:/var/log> su
Password:
linux-uy1d:/var/log # ls
acpid cups mail.err ntp wtmp
apparmor faillog mail.info pk_backend_zypp Xorg.0.log
audit firewall mail.warn pk_backend_zypp-1 Xorg.0.log.old
boot.log gdm mcelog pm-powersave.log YaST2
boot.msg krb5 messages pm-suspend.log zypp
boot.omsg lastlog NetworkManager samba zypper.log
btmp localmessages news warn
ConsoleKit mail nscd.log wpa_supplicant.log
linux-uy1d:/var/log #

studdyhalllooser said:
Ok. I was running barnacle for the previous tests. Wireless tether for root was version 2.0.2. I uninstalled it real quick and installed 1.6 so my SSID changed back to G1Tether for this test. Here are my results
PHP:
[email protected]:~> su
Password:
linux-uy1d:/home/jonathon # iwconfig wlan0 essid G1Tether
linux-uy1d:/home/jonathon # ifconfig wlan0
wlan0 Link encap:Ethernet HWaddr 70:F1:A1:BD:C9:F5
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
linux-uy1d:/home/jonathon #
For the file you asked about; I cannot find it when browsing the file manager so I opened up the terminal in that location under root. Then used the "ls" command to show the contents of that folder. I cannot find the file you are asking about. Am I doing this correctly? I do not know many terminal commands.
PHP:
[email protected]:/var/log> su
Password:
linux-uy1d:/var/log # ls
acpid cups mail.err ntp wtmp
apparmor faillog mail.info pk_backend_zypp Xorg.0.log
audit firewall mail.warn pk_backend_zypp-1 Xorg.0.log.old
boot.log gdm mcelog pm-powersave.log YaST2
boot.msg krb5 messages pm-suspend.log zypp
boot.omsg lastlog NetworkManager samba zypper.log
btmp localmessages news warn
ConsoleKit mail nscd.log wpa_supplicant.log
linux-uy1d:/var/log #
Click to expand...
Click to collapse
You did it all right, I just made a mistake. In opensuse dmesg is piped to /var/log/messages not /var/log/dmesg. Small difference between gentoo and opensuse .
So try connecting with networkmanager and then posting the output of /var/log/messages. Hopefully that tells us what is going wrong.

Ok. I must be doing something wrong. I cannot do anything with the messages file as i do not have permission to modify it?? I can get into the folder location as SU in terminal but do not know how to open it or copy it. There is also a file named "localmessages". Not sure if it is what your looking for but I was able to open it up. Here it is:
Code:
Jul 23 13:53:23 linux-uy1d dhcpcd[6503]: eth0: dhcpcd 3.2.3 starting
Jul 23 13:53:23 linux-uy1d dhcpcd[6503]: eth0: hardware address = a4:ba:db:d5:cc:84
Jul 23 13:53:23 linux-uy1d dhcpcd[6503]: eth0: broadcasting for a lease
Jul 23 13:53:43 linux-uy1d dhcpcd[6503]: eth0: timed out
Jul 23 13:53:43 linux-uy1d dhcpcd[6503]: eth0: trying to use old lease in `/var/lib/dhcpcd/dhcpcd-eth0.info'
Jul 23 13:53:43 linux-uy1d dhcpcd[6503]: eth0: lease information file `/var/lib/dhcpcd/dhcpcd-eth0.info' does not exist
Jul 23 13:53:43 linux-uy1d dhcpcd[6503]: eth0: broadcasting for a lease
Jul 23 13:53:46 linux-uy1d dhcpcd[8083]: wlan0: dhcpcd 3.2.3 starting
Jul 23 13:53:46 linux-uy1d dhcpcd[8083]: wlan0: hardware address = 70:f1:a1:bd:c9:f5
Jul 23 13:53:46 linux-uy1d dhcpcd[8083]: wlan0: broadcasting for a lease
Jul 23 13:54:03 linux-uy1d dhcpcd[6503]: eth0: timed out
Jul 23 13:54:03 linux-uy1d dhcpcd[6503]: eth0: trying to use old lease in `/var/lib/dhcpcd/dhcpcd-eth0.info'
Jul 23 13:54:03 linux-uy1d dhcpcd[6503]: eth0: lease information file `/var/lib/dhcpcd/dhcpcd-eth0.info' does not exist
Jul 23 13:54:03 linux-uy1d dhcpcd[6503]: eth0: broadcasting for a lease
Jul 23 13:54:06 linux-uy1d dhcpcd[8083]: wlan0: timed out
Jul 23 13:54:06 linux-uy1d dhcpcd[8083]: wlan0: trying to use old lease in `/var/lib/dhcpcd/dhcpcd-wlan0.info'
Jul 23 13:54:06 linux-uy1d dhcpcd[8083]: wlan0: lease information file `/var/lib/dhcpcd/dhcpcd-wlan0.info' does not exist
Jul 23 13:54:06 linux-uy1d dhcpcd[8083]: wlan0: broadcasting for a lease
Jul 23 13:54:23 linux-uy1d dhcpcd[6503]: eth0: timed out
Jul 23 13:54:23 linux-uy1d dhcpcd[6503]: eth0: trying to use old lease in `/var/lib/dhcpcd/dhcpcd-eth0.info'
Jul 23 13:54:23 linux-uy1d dhcpcd[6503]: eth0: lease information file `/var/lib/dhcpcd/dhcpcd-eth0.info' does not exist
Jul 23 13:54:23 linux-uy1d dhcpcd[6503]: eth0: broadcasting for a lease
Jul 23 13:54:26 linux-uy1d dhcpcd[8083]: wlan0: timed out
Jul 23 13:54:26 linux-uy1d dhcpcd[8083]: wlan0: trying to use old lease in `/var/lib/dhcpcd/dhcpcd-wlan0.info'
Jul 23 13:54:26 linux-uy1d dhcpcd[8083]: wlan0: lease information file `/var/lib/dhcpcd/dhcpcd-wlan0.info' does not exist
Jul 23 13:54:26 linux-uy1d dhcpcd[8083]: wlan0: broadcasting for a lease
Jul 23 13:54:43 linux-uy1d dhcpcd[6503]: eth0: timed out
Jul 23 13:54:43 linux-uy1d dhcpcd[6503]: eth0: trying to use old lease in `/var/lib/dhcpcd/dhcpcd-eth0.info'
Jul 23 13:54:43 linux-uy1d dhcpcd[6503]: eth0: lease information file `/var/lib/dhcpcd/dhcpcd-eth0.info' does not exist
Jul 23 13:54:43 linux-uy1d dhcpcd[6503]: eth0: broadcasting for a lease
Jul 23 13:54:46 linux-uy1d dhcpcd[8083]: wlan0: timed out
Jul 23 13:54:46 linux-uy1d dhcpcd[8083]: wlan0: trying to use old lease in `/var/lib/dhcpcd/dhcpcd-wlan0.info'
Jul 23 13:54:46 linux-uy1d dhcpcd[8083]: wlan0: lease information file `/var/lib/dhcpcd/dhcpcd-wlan0.info' does not exist
Jul 23 13:54:46 linux-uy1d dhcpcd[8083]: wlan0: broadcasting for a lease
Jul 23 13:55:03 linux-uy1d dhcpcd[6503]: eth0: timed out
Jul 23 13:55:03 linux-uy1d dhcpcd[6503]: eth0: trying to use old lease in `/var/lib/dhcpcd/dhcpcd-eth0.info'
Jul 23 13:55:03 linux-uy1d dhcpcd[6503]: eth0: lease information file `/var/lib/dhcpcd/dhcpcd-eth0.info' does not exist
Jul 23 13:55:03 linux-uy1d dhcpcd[6503]: eth0: broadcasting for a lease
Jul 23 13:55:06 linux-uy1d dhcpcd[8083]: wlan0: timed out
Jul 23 13:55:06 linux-uy1d dhcpcd[8083]: wlan0: trying to use old lease in `/var/lib/dhcpcd/dhcpcd-wlan0.info'
Jul 23 13:55:06 linux-uy1d dhcpcd[8083]: wlan0: lease information file `/var/lib/dhcpcd/dhcpcd-wlan0.info' does not exist
Jul 23 13:55:06 linux-uy1d dhcpcd[8083]: wlan0: broadcasting for a lease
Jul 23 13:55:16 linux-uy1d dhcpcd[6503]: eth0: received SIGTERM, stopping
Jul 23 13:55:16 linux-uy1d dhcpcd[6503]: eth0: exiting
Jul 23 13:55:16 linux-uy1d dhcpcd[8083]: wlan0: received SIGTERM, stopping
Jul 23 13:55:16 linux-uy1d dhcpcd[8083]: wlan0: exiting

How to setup chormecast in dlink 2750 router

Please help me to set up chormecast in dlink 2750 u router
i can connect to router but it show not connect to internet
thanks in advance

What are the first 4 digits of your serial number? Just curious what firmware build you might be on. If you're on 12072 you might want to get root while you still can!
Looks like your router is D-Link 2750U?
Page 36 lists a Wireless Multicast Forwarding (WMF) option - you might have to enable that for Chromecast discovery to work, but first we need to get Internet...
Page 58 lists a LAN to LAN (Intra LAN) Multicast Enable option - again, you might have to enable that for Chromecast discovery to work, but first we need to get Internet...
Page 63 - Enable IGMP Snooping - you may need to toggle this setting.
Other than those, I dont' really see anything that would specifically block Internet access from Chromecast... Make sure you can ping 8.8.8.8 and 8.8.4.4 from the 2.4 GHz wireless network using another device if you can.

Sorry for the late reply
it work automatically
i just have o brought a wifi extender as my router far away from my tv

permanent wifi problem

hi everyone
after july security update i got broken wifi in my TA-1052.
may be its just coincidence but... who knows...
after july security update i discovered strange wifi behavior - my nokias wifi tries to connect - disconnect - tries to connect... this process repeats up to 10 times and after this everything was good.
but yesterday after connecting to any 2.4ghz wifi point i i see "connected. no internet"
i have several linksys 2,4ghz routers and i have the same problem with them... also i have no any 5ghz router to check.
i made hard reset of my nokia - doesnt work...
right now im trying to find link to correct july security 00w_5_15D to reinstall it... may be someone can share with me with this link?
is it possible to downgrade security patch?
any suggestions will be appreciate )