Related
Any solution?
Only GPRS/EDGE does work, if 3G is available, it disconnects automatically until 3G isn't available.
Solution: Set to 2G-Only :-(
Anyone has the same problem?
I didn't have this problem with FRF 72.
Provider: Sunrise Switzerland
Radio: 32.36.00.28U_4.06.00.12_7
Have you tried going into your phone settings from *#*#4636#*#* and setting it to wcdma only? I did that on mine not too long ago and no more dropping to edge for me!
-------------------------------------
Sent via the XDA Tapatalk App
andi86 said:
Any solution?
Only GPRS/EDGE does work, if 3G is available, it disconnects automatically until 3G isn't available.
Solution: Set to 2G-Only :-(
Anyone has the same problem?
I didn't have this problem with FRF 72.
Provider: Sunrise Switzerland
Radio: 32.36.00.28U_4.06.00.12_7
Click to expand...
Click to collapse
does it lose complete signal? or does it show 3g still but just not doing anything?
Mine was working at first after flash. Then at about 2am it just kept trying to load then times out. Still shows 3g but just dont do anything. Im hoping its just tmobile messing with their towers... I dont see why it would work at first then not now..
The problem is, that i can only have a internet connection, when the phone is logged in into a gsm or edge network.
as soon as wcdma is available, the phone disconnects from the internet.
the signal is always available, but it looses the internet connection when it changes to 3G mode.
when the phone changes from 2G->3G mode, i see for 1s the 3G icon and then no icon will bi there.
when it changes back from 3G->2G, the EDGE/GPRS icon is visible again.
andi86 said:
the signal is always available, but it looses the internet connection when it changes to 3G mode.
when the phone changes from 2G->3G mode, i see for 1s the 3G icon and then no icon will bi there.
when it changes back from 3G->2G, the EDGE/GPRS icon is visible again.
Click to expand...
Click to collapse
ok thanks for clarification. My problem is different. I think related to phone company.. I still show the 3g signal and even have bars, but the pages dont load and eventually gives me the check your service and try again alert....
So Im hoping soon its working again for me... And I hope you as well figure it out.....
Thank you Good luck!
Had the same issue after update, did *#*#4636#*#* and noticed I was set to GSM only. Set it to WCDMA preferred and now it's good.
Thank you very much, thats the solution!!
Andi
ezhangin said:
Had the same issue after update, did *#*#4636#*#* and noticed I was set to GSM only. Set it to WCDMA preferred and now it's good.
Click to expand...
Click to collapse
Sent from my Nexus One using XDA App
ezhangin said:
Had the same issue after update, did *#*#4636#*#* and noticed I was set to GSM only. Set it to WCDMA preferred and now it's good.
Click to expand...
Click to collapse
Thank you. Updated to FRF83 this morning and I've had a full 3g signal, just couldn't pull data all day. Could over edge. Sure enough, GSM only was selected.
AT&T N1.
I'm having the same issue on a non-rooted phone on T-Mobile. No 3G after the FRF83 update. Full bars of service and 3G displayed in the status bar. Dropping to Edge only works but there is no data with 3G.
Lost Dog said:
I'm having the same issue on a non-rooted phone on T-Mobile. No 3G after the FRF83 update. Full bars of service and 3G displayed in the status bar. Dropping to Edge only works but there is no data with 3G.
Click to expand...
Click to collapse
Same issue here.
Switching to WCDMA preferred doesn't work for me though.....any help is welcome
I think it's a hardware problem with a lot of N1's.
Mine was ok the first 2 months, and later, 3g not working. This is driving me crazy ):
I have tried everything. Change the simcard, I did a reset of the data with my telcon, and nothing happens.
I've seen these problems on many N1's.
I hope google / htc release a fix for this problem.
Lost Dog said:
I'm having the same issue on a non-rooted phone on T-Mobile. No 3G after the FRF83 update. Full bars of service and 3G displayed in the status bar. Dropping to Edge only works but there is no data with 3G.
Click to expand...
Click to collapse
how bout checking your bands in the service menu. so *#*#4636#*#* -> phone info -> press the menu key for more options -> select bands -> choose one appropriate for your region (ie "USA BANDS").
If all else fails do a factory reset by going to the settings -> privacy -> restore factory defaults.. of course do a backup/sync/whatever before just to make sure you can get all your apps back.
There's other ways to do a factory reset via the bootloader .. its under recovery and you press up volume or the trackball I think and you can just select all the clear/erase settings there and that should clear out everything on the phone's internal storage.
The factory reset worked for me (via bootloader) when I upped from update-1 to FRF50 and didn't have any data icon next to my signal strength. Could call out but couldn't get data.
Hope that helps.
jasonpich said:
I think it's a hardware problem with a lot of N1's.
Mine was ok the first 2 months, and later, 3g not working. This is driving me crazy ):
I have tried everything. Change the simcard, I did a reset of the data with my telcon, and nothing happens.
I've seen these problems on many N1's.
I hope google / htc release a fix for this problem.
Click to expand...
Click to collapse
Check your APN settings. Do a full factory reset from the bootloader. If nothing works you should call tech support again. Most 3g issues where you have issues with connecting are service/signal level related. I *****ed early about my 3g issues on tmobile and it was the network as they've pretty much gone away with improving the backhaul in my area for HSDPA+ or updates to the phone's radio.
HTC is really really really cool about swapping phones and repairing them. If you feel you have a nexus that has hardware issues call them. I did this 3 times already (one time for minor cosmetic issues with the refurb they sent) and I couldn't be happier about how willing they were to replace/repair the phone. It turns out I really didn't have any issues with them at all.. with any issues with hardware from the second refurbished phone. It was service or software related and I'm happy to say with updates/tmobile service improvements I couldn't be happier with this phone.
blisk said:
Check your APN settings. Do a full factory reset from the bootloader. If nothing works you should call tech support again. Most 3g issues where you have issues with connecting are service/signal level related. I *****ed early about my 3g issues on tmobile and it was the network as they've pretty much gone away with improving the backhaul in my area for HSDPA+ or updates to the phone's radio.
HTC is really really really cool about swapping phones and repairing them. If you feel you have a nexus that has hardware issues call them. I did this 3 times already (one time for minor cosmetic issues with the refurb they sent) and I couldn't be happier about how willing they were to replace/repair the phone. It turns out I really didn't have any issues with them at all.. with any issues with hardware from the second refurbished phone. It was service or software related and I'm happy to say with updates/tmobile service improvements I couldn't be happier with this phone.
Click to expand...
Click to collapse
Thanks blisk, but the thing I don't understand is why Blackberry 9700 with T-Mobile bands, doesn't have problems at all ?
By the way, I rooted my phone , so the thing with the warranty it's complicated
I had it happen last night at work all night, but when i got home i checked my wife's tp2 and it also was doing the same thing so for levity wasn't the phone but tmobile. They started worming the same time also.... I think its tmobile.
Hello, I had the same problem with my imported n1. I'm using the tmobile version non rooted fully stock manually updated to frf83. I did a *#*#4636#*#* and selected wcdma only, rebooted and couldn't connect to my gsm network. Went in again and did a wcdma preferred, rebooted, and I works better, still changes fast to edge and G, but less often, I'm still trying it but I have high hopes its gonna be ok
Mmmm i did have problems with 3G too after pushing FRF83, but i found out that for some reason the APN settings weren't set correctly after the update. In my case the port setting after the proxy of the APN wasn't set, i changed to the correct value and it worked.
In conclusion, check your APN settings.
Just went from FRF72 to FRF83 and it's working fine.
I'm currently set to GSM auto (PRL) in the *#*#4636#*#* and I didn't change it to that after putting on FRF83.
Yesterday my Milestone dropped the network and wrote "Only emergency calls". On other phones there was maximum signal. After a while the phone logged in to the network, but lost the signal again. I thought something is with the ROM, so I made a factory reset but didn't help. I flashed the correct SBF file (first Éclair, then Froyo), but didn't help. I restored an earlier MOD I used without any problem but didn't work.
I always used the German baseband files with other MODs because my Milestone is German.
The problem is that if I make anything (I mean anything related to the data connection), the GSM signal disappears, sometimes data connection remain with no problem, sometimes it is lost, too, but sometimes it has GSM signal with only EDGE network. If I do nothing, just turn off the screen and do nothing, everything goes back to normal, and the phone has normal data connection with GSM signal, I can make or receive phone calls.
I put in another SIM but the issue was the same.
Can I try something related to software and didn't try yet or this is a hardware failure? And if so, what is the price of a GSM module? I couldn't find it.
MOD: It seems that only the 3G is not working (sometimes HSPA does while 3G phone connection don't), with 2G there isn't any problem.
dial *#*#4636#*#*
Under phone info, try a different network type.
It probably defaults to GSM (auto). It does on mine anyway and it's fine.
But maybe WCDMA preferred, GSM only, or WCDMA only will work better.
It depends on which is screwing up... the WCDMA or the GSM
edit: had the dialpad code wrong... again.. geez
lordfreyr said:
Yesterday my Milestone dropped the network and wrote "Only emergency calls". On other phones there was maximum signal. After a while the phone logged in to the network, but lost the signal again. I thought something is with the ROM, so I made a factory reset but didn't help. I flashed the correct SBF file (first Éclair, then Froyo), but didn't help. I restored an earlier MOD I used without any problem but didn't work.
I always used the German baseband files with other MODs because my Milestone is German.
The problem is that if I make anything (I mean anything related to the data connection), the GSM signal disappears, sometimes data connection remain with no problem, sometimes it is lost, too, but sometimes it has GSM signal with only EDGE network. If I do nothing, just turn off the screen and do nothing, everything goes back to normal, and the phone has normal data connection with GSM signal, I can make or receive phone calls.
I put in another SIM but the issue was the same.
Can I try something related to software and didn't try yet or this is a hardware failure? And if so, what is the price of a GSM module? I couldn't find it.
MOD: It seems that only the 3G is not working (sometimes HSPA does while 3G phone connection don't), with 2G there isn't any problem.
Click to expand...
Click to collapse
Are you sure you have applied the correct baseband?
I would tell to re-apply thru AOR.
Sent from my Milestone using XDA Premium App
You could go to settings, wireless and networks and somewhere there there is use only 2g networks and if that is checked, you could try to uncheck it. That is what happened to me before on the froyo mod. Also, you could try turning on airplane mode, then turn it off. Good luck
I always used the German baseband, tried to switch 2G/3G many times, applied the baseband trough OR, applied the RTEU baseband, re-flashed the ROM, the original Éclair, the Froyo, again and again but nothing helped. I gave up I decided to go to the service. Before that on a forum somebody asked something, I gave an answer but I was not 100% sure about it, so I flashed the RTEU Froyo.
And it worked. The 3G, HSPA, 2G, EDGE, phone functions all are working now. My phone is truly German, it has QWERTZ keyboard and the original ROM was the ROM from Deutsche Vodafone (tried that one before, too), it has the logo on its box, and the German baseband files always worked. I don't know what just happened, it's simply working now. Why now... don't know.
I bought nexus one from my friend.
I am currently using HD2 with 3g data.
When I plugged in my sim card to the n1, it only worked with edge.
So, I seared internet for some information and I found out something about "*#*#6436#*#*" and change the setting to WCDMA only. Then the phone got no signal at all, so I changed back to WCDMA preferred. Then I did ping test but it did not seem to work very well.
Then I played with some APN setting and I realized that I lost data connection completely (phone still working)
I have tried to reset the phone but no luck.
Can anyone please help me with the problem? I am using T-mobile.
Thank you.
Pull your battery, and look at the back of your phone. At the top of the dark area there are numbers, look at the PB or FCC ID numbers. If they end in 9110 then you have an AT&T version of the phone, and the hardware will not work with T-Mobile's 3G service...
khunny7 said:
I bought nexus one from my friend.
I am currently using HD2 with 3g data.
When I plugged in my sim card to the n1, it only worked with edge.
So, I seared internet for some information and I found out something about "*#*#6436#*#*" and change the setting to WCDMA only. Then the phone got no signal at all, so I changed back to WCDMA preferred. Then I did ping test but it did not seem to work very well.
Then I played with some APN setting and I realized that I lost data connection completely (phone still working)
I have tried to reset the phone but no luck.
Can anyone please help me with the problem? I am using T-mobile.
Thank you.
Click to expand...
Click to collapse
are you in the USA? you need to list your location. it is likely that you purchased the wrong version of the nexus one. there is an ATT version and a tmobile version. each only works with the proper 3G. so an ATT n1 on tmobile only gets edge, and vice versa. check which version you own.
hello every body
i have this problem with my nexus one when i am connected to 3g service (umts,hsdpa,Etc'). i can't make calls or receive any calls, i can't use the internet (data) or get sms and Etc'. but i have full bars reception. when i check the vi in setting to "use only 2g" the phone work great.
i tried everything downgrade/upgrade roms,radios. i tried to go back to my first backup and even do PASSIMG but nothing help i googled it every where but nothing
please some one can help???
without 3g the smartphone is useless
thanks,
shushkis
What network you on? I would at least see how old the sim card is.
Lots of time if you have an older sim card it just can't handle a newer system.
I am connected through Orange IL
and i tried switching sims even with other networks.
and more the phone worked fine at the beginning it just happened i remember i switch to one of CY roms and it happened
Have you tried a full wipe and reinstall the rom?
yes of course i tried customized roms and stock roms but nothing helped
I would check your apn settings...
apn connected to taking or getting calls?
i thought it's just for internet connection
Its just a guess.
If its a problem on multiple ROMs, its likely to be either hardware or settings. Settings are cheaper and easier to test, and that's the only setting I can think of...?
Of course, doing a full wipe (including system), installing a new ROM, and testing before you restore any apps and settings may be another way to test, but since the apn settings are pre-baked into most ROMs, it wouldn't rule our the apn...?
OK I tried to put apn settings and it didnt help
you say hardware?
but when I check in settings "use only 2g" the transceiver works great .
maybe the nexus have two transceiver one for 2g and one for 3g?
seems un-logical
No there are two radios one for 3g and one for 2g because 2g is for calls and 3g for data but when 3G is unavailable the phone will use the 2g for the data.
The Same Trouble
shushkis,
I have the same trouble, my 3G connection works so bad, but if I use only 2g connection, all works good... I have no idea what happend with my N1. I have a N1 for 3G 850 (AT&T) model.
Thanks for advantage.
So maybe the problem is the hardware? if the N1 have two inidvidul transcivers?
I have also the same problem. I've tried many different roms and radios. I use 900/2100 3G. What's strang is that 3G works perfectly at home, but when moving to another tower I get emergency calls only warning. 2g works fine.
I just started having 3G issues at home. With 3G on the phone reboots like once an hour, but on 2G I've gone days without a reboot. My 3G signal is not the best at home, but I don't know why that would make the phone reboot. I'm on T-Mo USA.
bobbyphoenix said:
I just started having 3G issues at home. With 3G on the phone reboots like once an hour, but on 2G I've gone days without a reboot. My 3G signal is not the best at home, but I don't know why that would make the phone reboot. I'm on T-Mo USA.
Click to expand...
Click to collapse
Go get a new SIM card...
danger-rat said:
Go get a new SIM card...
Click to expand...
Click to collapse
The one I'm using is only a couple months old, and it works well in my Desire HD, and my Moto Defy. It's only the N1, but I guess maybe it could be that. I'll look into more.
If it's only a few months old, then it may nor be the SIM that is the problem. I suggested it because a number of T-Mo users were having similar problems after a recent network upgrade, and a new SIM seems to fix the issue for most...
I'm getting a chance to do some extended testing with data roaming. I found a couple of other data roaming problem threads, but this issue is different than the problems discussed in those.
The HTC One is rooted, unlocked, S-OFF, stock 4.4.2 (4.06.651.4), with PRL 56018 installed from CDMA Workshop. I've installed a couple of the patches floating around for WiFi tether. I also have an HTC EVO 4G LTE with the 56018 PRL installed via QPST.
Right now, I am in an area with extremely weak Sprint signal and decent Verizon signal. The EVO 4G LTE finds Verizon 3G EVDO and will voice/data roam just fine. SignalCheck verifies that the provider is Verizon for 1x and EVDO, with signal between -90 to -100 dB. However, the One will not data roam. SignalCheck indicates that the One finds Verizon for voice (1X), but does not connect for data roaming. If I watch SignalCheck long enough, I can see that the One will find the Verizon EVDO for a few seconds every five minutes or so, but it won't "hold" the EVDO signal. On Sprint, the ONE will find both 3G and 4G.
I've played around with various mobile data settings, but nothing seems to help. In fact, the One will pop up the messages that data roaming is in effect, but there is no data connection. Since the EVO 4G LTE will EVDO roam, it seems that the One should EVDO roam as well.
Any ideas or suggestions on what to look at? On Sprint the 3G is usually ePHRD, not EVDO, perhaps there is some issue with EVDO on the ONE? I thinking about getting Roam Control to see if that would make any difference. I haven't taken the 4.06.651.9 update either.
Thanks!
I had a chance to do some further data roaming testing with the One and Evo 4G LTE side by side.
Roam Control seems to work fine on the One, except that the color of the blue button for selecting the roaming mode is hard to distinquish.
Unfortunately, it seems that the One will not lock on to a Verizon EVDO signal. I found several areas with strong EVDO signal. The EVO connected just fine, but the One wouldn't. The One does fine with Sprint's eHRPD signal, and will lock on to the Verizon 1xRTT for voice.
I don't know how to do further debugging. I guess it could be a radio problem, an issue with the 56018 PRL and the One, or some other issue.
Any suggestions are welcome!
jbhtexas said:
I had a chance to do some further data roaming testing with the One and Evo 4G LTE side by side.
Roam Control seems to work fine on the One, except that the color of the blue button for selecting the roaming mode is hard to distinquish.
Unfortunately, it seems that the One will not lock on to a Verizon EVDO signal. I found several areas with strong EVDO signal. The EVO connected just fine, but the One wouldn't. The One does fine with Sprint's eHRPD signal, and will lock on to the Verizon 1xRTT for voice.
I don't know how to do further debugging. I guess it could be a radio problem, an issue with the 56018 PRL and the One, or some other issue.
Any suggestions are welcome!
Click to expand...
Click to collapse
Providers dont like roaming, the newer the phone is the less likely it will be to roam, the first two M7 radios would not allow any roaming at all on my phone, the latest 2 do allow roaming but I need to force "roam only" with roam control, I am on the latest radio running GPE rom and use roam control to force roaming whenever verizon has a better signal and it works good. I am using PRL 56015 flashed via CDMA workshop.
---------- Post added at 09:10 PM ---------- Previous post was at 09:08 PM ----------
jbhtexas said:
The HTC One is rooted, unlocked, S-OFF, stock 4.4.2 (4.06.651.4), with PRL 56018 installed from CDMA Workshop. I've installed a couple of the patches floating around for WiFi tether. I also have an HTC EVO 4G LTE with the 56018 PRL installed via QPST.
Click to expand...
Click to collapse
Where did you get that PRL?
mcerk02 said:
Where did you get that PRL?
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=2573604
Unfortunately, my One will not data roam, even with Roam Control. It sees the EVDO for a few seconds, but won't hold it.
Would there be any tweaks that could be made to the radio from CDMA Workshop that might affect the data roaming behavior?
jbhtexas said:
http://forum.xda-developers.com/showthread.php?t=2573604
Unfortunately, my One will not data roam, even with Roam Control. It sees the EVDO for a few seconds, but won't hold it.
Would there be any tweaks that could be made to the radio from CDMA Workshop that might affect the data roaming behavior?
Click to expand...
Click to collapse
I dont think you can tweak a radio, all I could suggest is make sure you are on the latest radio from here
http://forum.xda-developers.com/showthread.php?t=2406330
and try the 56015 PRL from here
http://forum.xda-developers.com/showthread.php?t=1880781
I flashed the PRL with cdma workshop and use roam control when needed and it roams on 3G no problem. let me know if any of that helps.
mcerk02 said:
I dont think you can tweak a radio, all I could suggest is make sure you are on the latest radio from here
http://forum.xda-developers.com/showthread.php?t=2406330
and try the 56015 PRL from here
http://forum.xda-developers.com/showthread.php?t=1880781
I flashed the PRL with cdma workshop and use roam control when needed and it roams on 3G no problem. let me know if any of that helps.
Click to expand...
Click to collapse
I loaded PRL 56015 into the One with CDMA Workshop, but the problem remains...when roaming, the One will see the EVDO briefly but not hold it, according to SignalCheck.
I did a comparison between the various settings in the One and the EVO 4G LTE (where roaming works fine) using CDMA WS. The are significant differences, particularly on the CDMA, CDMA-2, and EVDO pages. For example, on the EVDO page, the EVO has a username ([email protected]) for HDR_User_long, but the One doesn't have one. The EVDO revision is also different. I don't know enough to fool with these settings.
Actually, the One is missing values for many settings that the EVO has. I'm beginning to wonder if somehow the One didn't get provisioned properly.
Thanks!
jbhtexas said:
I loaded PRL 56015 into the One with CDMA Workshop, but the problem remains...when roaming, the One will see the EVDO briefly but not hold it, according to SignalCheck.
I did a comparison between the various settings in the One and the EVO 4G LTE (where roaming works fine) using CDMA WS. The are significant differences, particularly on the CDMA, CDMA-2, and EVDO pages. For example, on the EVDO page, the EVO has a username ([email protected]) for HDR_User_long, but the One doesn't have one. The EVDO revision is also different. I don't know enough to fool with these settings.
Actually, the One is missing values for many settings that the EVO has. I'm beginning to wonder if somehow the One didn't get provisioned properly.
Thanks!
Click to expand...
Click to collapse
If you change any of them settings in CDMA workshop, save them first, if you screw something up you can reload the saved settings, I screwed with CDMA workshop alot in the past and you can do alot with it. Before screwing with them settings, did you try resetting or updating your data profile?..maybe something got messed up in the tweaking and flashing your doing. I flash all kinds of different stuff on my phone, every once in a while I flash a sense rom and update or reset my data profile just in case...
mcerk02 said:
If you change any of them settings in CDMA workshop, save them first, if you screw something up you can reload the saved settings, I screwed with CDMA workshop alot in the past and you can do alot with it. Before screwing with them settings, did you try resetting or updating your data profile?..maybe something got messed up in the tweaking and flashing your doing. I flash all kinds of different stuff on my phone, every once in a while I flash a sense rom and update or reset my data profile just in case...
Click to expand...
Click to collapse
I did "update profile" from Settings->System updates, but nothing changed. What you mean by resetting the data profile?
Thanks!
jbhtexas said:
I did "update profile" from Settings->System updates, but nothing changed. What you mean by resetting the data profile?
Thanks!
Click to expand...
Click to collapse
I am not on a sense rom right now and I forget the codes, try entering ##3282# or *#*#3282#*#* in your dialer, it should bring up a data menu, there should be an option to do a reset, it will basically erase your data profile and reboot, when it reboots it will do an activation and reset everything....or ##786# will completely reset everything, that has saved me once or twice but that also factory rests your phone. these will only work on a sense rom and I reccoment a backup before doing anything, just in case... if that dont work do a google search for epst codes, and find the one that resets your data profile.
mcerk02 said:
I am not on a sense rom right now and I forget the codes, try entering ##3282# or *#*#3282#*#* in your dialer, it should bring up a data menu, there should be an option to do a reset, it will basically erase your data profile and reboot, when it reboots it will do an activation and reset everything....or ##786# will completely reset everything, that has saved me once or twice but that also factory rests your phone. these will only work on a sense rom and I reccoment a backup before doing anything, just in case... if that dont work do a google search for epst codes, and find the one that resets your data profile.
Click to expand...
Click to collapse
I did a profile reset with ##3282#, and the behavior has changed somewhat. The One is now holding the EVDO signal according to SignalCheck. However, if I try to open a web page, a message box pops up indicating that data roaming needs to be enabled. If I tap on "data roaming" in the message box, it takes me to the mobile data settings. I have been over and over those settings, and tried different combinations of things, but I can't seem to come up with the magic setting that will make the phone think that data roaming is enabled. I am forcing roaming with Roam Control.
Is there some "hidden" setting to enable data roaming? There is a "CDMA Roaming" setting that has choices of Home/Automatic, and I have it set to Automatic. I have identical settings to the Evo in the mobile data settings, but I can't make it work on the One.
jbhtexas said:
I did a profile reset with ##3282#, and the behavior has changed somewhat. The One is now holding the EVDO signal according to SignalCheck. However, if I try to open a web page, a message box pops up indicating that data roaming needs to be enabled. If I tap on "data roaming" in the message box, it takes me to the mobile data settings. I have been over and over those settings, and tried different combinations of things, but I can't seem to come up with the magic setting that will make the phone think that data roaming is enabled. I am forcing roaming with Roam Control.
Is there some "hidden" setting to enable data roaming? There is a "CDMA Roaming" setting that has choices of Home/Automatic, and I have it set to Automatic. I have identical settings to the Evo in the mobile data settings, but I can't make it work on the One.
Click to expand...
Click to collapse
What rom are you using?, I think the stock roms from Sprint no longer have the "allow data roaming" option, Sprint tries to avoid us using roaming as much as possible, so if you are on stock rom or something close, you probly don't have this option, try flashing a modified rom that may have this option, or if you are familiar with using the exposed framework, I think there is a module you can use to enable the data roaming. I personally use Gruesomewolf's GPE rom and it has the option built in if you want to try it.
mcerk02 said:
What rom are you using?, I think the stock roms from Sprint no longer have the "allow data roaming" option, Sprint tries to avoid us using roaming as much as possible, so if you are on stock rom or something close, you probly don't have this option, try flashing a modified rom that may have this option, or if you are familiar with using the exposed framework, I think there is a module you can use to enable the data roaming. I personally use Gruesomewolf's GPE rom and it has the option built in if you want to try it.
Click to expand...
Click to collapse
I'm on the stock 4.06.651.4 ROM (rooted and S-OFF). This is my wife's phone, and I'd like to keep it stock and simple, as she's not a techie. However, she also travels where data roaming is required, so I might have to try another ROM.
Interestingly, My EVO 4G LTE doesn't have an "allow data roaming" setting under mobile network settings that I can find, but it roams just fine. In fact, the mobile data settings on the EVO and One are almost identical, except that the One has some additional GMS options. I wonder if there is some setting in a file like build.prop that affects data roaming.
I installed a couple of native hotspot hacks on the One. In looking through the zip files for those hacks to see what they actually did (which was quite minimal), some network-related things were changed in /system/customize/ACC/default.xml relative to the file in the original ROM, and a shell script was added that executes several iptables commands. I may try to manually undo those hacks to see if it has any effect. At this point, we need the data roaming more than the hotspot.
jbhtexas said:
I'm on the stock 4.06.651.4 ROM (rooted and S-OFF). This is my wife's phone, and I'd like to keep it stock and simple, as she's not a techie. However, she also travels where data roaming is required, so I might have to try another ROM.
Interestingly, My EVO 4G LTE doesn't have an "allow data roaming" setting under mobile network settings that I can find, but it roams just fine. In fact, the mobile data settings on the EVO and One are almost identical, except that the One has some additional GMS options. I wonder if there is some setting in a file like build.prop that affects data roaming.
I installed a couple of native hotspot hacks on the One. In looking through the zip files for those hacks to see what they actually did (which was quite minimal), some network-related things were changed in /system/customize/ACC/default.xml relative to the file in the original ROM, and a shell script was added that executes several iptables commands. I may try to manually undo those hacks to see if it has any effect. At this point, we need the data roaming more than the hotspot.
Click to expand...
Click to collapse
Alot of your issues can be solved with a custom rom, you wouldnt need to install the hotspot hacks either, most have native hotspot built in.
mcerk02 said:
Alot of your issues can be solved with a custom rom, you wouldnt need to install the hotspot hacks either, most have native hotspot built in.
Click to expand...
Click to collapse
Getting a chance to work on this issue again...it seems that the EV-DO problem with my HTC One is not limited to roaming, but also occurs on the Sprint network.
Again, doing side-by-side comparison between the HTC One and my EVO 4G LTE on Sprint network:
1) Set network mode to LTE/CDMA. According to SignalCheck, both phones will find Sprint LTE and display the 4G indicator in the status bar, and both will occasionally drop back to Sprint eHRPD for periods of 5-10 minutes (displaying the 3G icon in the status bar). Network is available to apps in both the LTE and eHRPD cases. No problems here.
2) Now...change network mode to CDMA Only. According to SignalCheck, the EVO will find Sprint EV-DO, the status indicator will change to 3G, and network is available to apps. However, on the One, SignalCheck indicates that EV-DO is found (but doesn't indicate which carrier), there is no 3G (or 4G) icon in the status bar, and apps report that there is no network. The EV-DO signal is strong for both phones.
So, it seems that on the One, LTE and eHRPD are working, but there is some kind of problem with legacy EV-DO, where the phone can find a signal, but can't complete the process of registering on the network, whether Sprint or roaming.
Do eHRPD and EV-DO use the same radio? Trying to rule out a hardware issue. I am thinking of flashing a different radio firmware. Perhaps something got corrupted when I did the OTA update.
Not that Sprint wouldn't do this, but it would seem odd to put something in the stock ROM that would prevent EV-DO, even on Sprint's network. Is there somebody out there on the stock ROM who could confirm that they can get network in CDMA only mode?
Thanks!
So, I finally got this problem solved! I had to do a ##786# "hard reset". After the reset, EV-DO works fine.
The reset process was interesting. I did backups, expecting the phone to be wiped. I entered ##786# and the phone said it was preparing, and then rebooted. But it rebooted into recovery (I have TWRP). Not being exactly sure what to do, I rebooted into the system. The phone booted up, and the provisioning process started and completed. It then fetched the PRL. But nothing was wiped out. Apps, data, and sdcard were all intact. Oh, well, no complaints, and everything seems to be working fine. I used CDMA workshop to put PRL 56018 back, and roaming seems to be working.
jbhtexas said:
So, I finally got this problem solved! I had to do a ##786# "hard reset". After the reset, EV-DO works fine.
The reset process was interesting. I did backups, expecting the phone to be wiped. I entered ##786# and the phone said it was preparing, and then rebooted. But it rebooted into recovery (I have TWRP). Not being exactly sure what to do, I rebooted into the system. The phone booted up, and the provisioning process started and completed. It then fetched the PRL. But nothing was wiped out. Apps, data, and sdcard were all intact. Oh, well, no complaints, and everything seems to be working fine. I used CDMA workshop to put PRL 56018 back, and roaming seems to be working.
Click to expand...
Click to collapse
I know you got your issue fixed and its been a while but just a heads up in case you run into problems again, I got a replacement phone from sprint and had the exact same issues youe were having, It is a problem with the data profile not being configured correctly, in my case, the new phone did not have my user name correct, worked fine on sprint network for some reason, but I couldnt get 3g in roaming areas, using epst I put my correct user name in and everything worked perfectly...dont know what rom your running now either but NUISENSE is awesome with this phone and it has "roam only" opttion built in, no need for roam control app....
Thanks for the tip!
I'm using the stock ROM. Since my last post, I have been able to test romaing, as we've traveled off the Sprint network, and roaming 3G worked fine. The only issue was that in a one spot we were roaming on a regional carrier, and the phone had locked on a quite distant tower according to SignalCheck, instead of Verizion which had closer towers. This resulted in some loss of 3G just as we were trying to get radar data for a storm we were traveling through (bad timing). But that is most likely a PRL issue. In looking though some PRL analyis an earlier version of 56xxx on another site, Sprint apparently doesn't have roaming agreement in this particular area with Verizon. I wish I new more about PRL editing so I could fix that...