Related
Yesterday my moto x alerted me that the KitKat update had been downloaded and was ready to install. I selected INSTALL and the installation began. About a minute into it, it kicked me to the bootloader with the message, "Failed to hab check for recovery: 0x56. Boot up failed".
Also see my post at androidcentral.com at forums.androidcentral.com/moto-x/336036-kitkat-crashed-my-moto-x-unrecoverable.html
Note that my moto x has never been rooted.
forums.androidcentral.com/attachments/moto-x/92779d1384906583-kitkat-crashed-my-moto-x-unrecoverable-kitkat_error.jpg
I selected "Recovery" and it rebooted and attempted to re-install, but then I was met with a image very similar to this except it said "ERROR":
forums.androidcentral.com/attachments/moto-x/92780d1384906685-kitkat-crashed-my-moto-x-unrecoverable-android-error.jpg
Then a few seconds later it rebooted again and now it just gets stuck at the Motorola logo:
forums.androidcentral.com/attachments/moto-x/92781d1384906724-kitkat-crashed-my-moto-x-unrecoverable-moto_x_boot_logo_featured_small.jpg
If I try any of the other options in the boot loader, the behavior is the same.. it gets stuck at the Motorola logo. Yesterday it sat that way for 4 hours before the battery died.
Today I tried connecting it to my computer via USB. My Mac doesn't appear to recognize that it's been connected even though the drivers have been installed. In a Windows VM with MDM it recognized the first time I connected it, but the MDM icon promptly disappeared from the status bar.
I spoke with Verizon tier 2 tech support yesterday and they didn't seem very knowledgeable - the person I spoke with didn't even know what KitKat is.
Surprisingly, I thought I had set up the Motorola data backup to the cloud, but verizon tech support said I must not have enabled it. So my biggest worry is that I've lost all my data (pictures/videos/contacts/etc...).
I'm hoping that somebody on this forum might have some advice for me.
Thanks,
Chris
cbridgers, if you had some battery you could try download 4.2.2 sbf file and recover through RSD Lite.
xpc21 said:
cbridgers, if you had some battery you could try download 4.2.2 sbf file and recover through RSD Lite.
Click to expand...
Click to collapse
Thanks for your response. I could certainly do that.. but I first want to make sure I've pursued every avenue for recovering my data before I reflash/wipe.
cbridgers said:
Thanks for your response. I could certainly do that.. but I first want to make sure I've pursued every avenue for recovering my data before I reflash/wipe.
Click to expand...
Click to collapse
cbridgers, that error happened to me while i was trying to flash through RSD Lite the leaked version of Kitkat. Because it was only to AT&T phones, it gave me that error cause i didnt have an unlocked bootloader. So what i did was flash back the 4.2.2 and for my surprise the phone was with all my config and data, nothing was erased.
Few suggestions...
cbridgers said:
Thanks for your response. I could certainly do that.. but I first want to make sure I've pursued every avenue for recovering my data before I reflash/wipe.
Click to expand...
Click to collapse
I had the same issue. I was able to recover it once, but recreated the scenario for good measures. My best guess is this issue is free space related (you should have at least 3gb free), but I'll confirm later today.
In any case, try the following remedies (in order of severity):
** I'm assuming you have RSD Lite, fastboot, ADB and the Moto X drivers installed and working **
-- Solution #1 - Easiest --
1) Go into Fastboot mode (power button and vol. down)
2) In your console, type in "fastboot erase cache"
- This solved the issue in one of my test scenarios. It's the easiest and least severe to implement
-- Solution #2 - Medium --
1) Download the stock SBF firmware for your pre-KitKat ROM (sbf.droid-developers.org)
2) Unzip the ROM and copy the files to your fastboot directory
3) Go into Fastboot mode (power button and vol. down) and type in:
fastboot erase cache
fastboot erase customize
fastboot erase clogo
fastboot flash partition gpt.bin
fastboot flash system system.img
fastboot flash recovery recovery.img
fastboot flash boot boot.img
- This should preserve your user data and works in most circumstances, depending on how far the KitKat install proceeded before failing -
-- Solution #3 - Severe - Factory Reset --
1) Download the stock SBF firmware for your pre-KitKat ROM (sbf.droid-developers.org).
2) Unzip the ROM and edit the XML file. Delete the step operation that says "getVar". It should be the first line under step operations.
3) Use RSD lite to flash the firmware
- This will erase EVERYTHING. Say goodbye to your data. And porn.
Hope you get to recover using only the first two steps. If not, rinse then repeat. Good luck!
xpc21 said:
cbridgers, if you had some battery you could try download 4.2.2 sbf file and recover through RSD Lite.
Click to expand...
Click to collapse
SamSpadeXX said:
I had the same issue. I was able to recover it once, but recreated the scenario for good measures. My best guess is this issue is free space related (you should have at least 3gb free), but I'll confirm later today.
In any case, try the following remedies (in order of severity):
** I'm assuming you have RSD Lite, fastboot, ADB and the Moto X drivers installed and working **
-- Solution #1 - Easiest --
1) Go into Fastboot mode (power button and vol. down)
2) In your console, type in "fastboot erase cache"
- This solved the issue in one of my test scenarios. It's the easiest and least severe to implement
-- Solution #2 - Medium --
1) Download the stock SBF firmware for your pre-KitKat ROM (sbf.droid-developers.org)
2) Unzip the ROM and copy the files to your fastboot directory
3) Go into Fastboot mode (power button and vol. down) and type in:
fastboot erase cache
fastboot erase customize
fastboot erase clogo
fastboot flash partition gpt.bin
fastboot flash system system.img
fastboot flash recovery recovery.img
fastboot flash boot boot.img
- This should preserve your user data and works in most circumstances, depending on how far the KitKat install proceeded before failing -
-- Solution #3 - Severe - Factory Reset --
1) Download the stock SBF firmware for your pre-KitKat ROM (sbf.droid-developers.org).
2) Unzip the ROM and edit the XML file. Delete the step operation that says "getVar". It should be the first line under step operations.
3) Use RSD lite to flash the firmware
- This will erase EVERYTHING. Say goodbye to your data. And porn.
Hope you get to recover using only the first two steps. If not, rinse then repeat. Good luck!
Click to expand...
Click to collapse
Thanks for your detailed instructions! Solution #1 didn't work for me. Solution #2 gives me the following error when I run "fastboot flash system system.img":
load_file: could not allocate 870593756 bytes
error: cannot load 'system.img'
I'm not sure I want to try Solution #3 yet. May try to talk to Motorola first.
Thanks again for the detailed advice!
Chris
SamSpadeXX said:
I had the same issue. I was able to recover it once, but recreated the scenario for good measures. My best guess is this issue is free space related (you should have at least 3gb free), but I'll confirm later today.
In any case, try the following remedies (in order of severity):
** I'm assuming you have RSD Lite, fastboot, ADB and the Moto X drivers installed and working **
-- Solution #1 - Easiest --
1) Go into Fastboot mode (power button and vol. down)
2) In your console, type in "fastboot erase cache"
- This solved the issue in one of my test scenarios. It's the easiest and least severe to implement
-- Solution #2 - Medium --
1) Download the stock SBF firmware for your pre-KitKat ROM (sbf.droid-developers.org)
2) Unzip the ROM and copy the files to your fastboot directory
3) Go into Fastboot mode (power button and vol. down) and type in:
fastboot erase cache
fastboot erase customize
fastboot erase clogo
fastboot flash partition gpt.bin
fastboot flash system system.img
fastboot flash recovery recovery.img
fastboot flash boot boot.img
- This should preserve your user data and works in most circumstances, depending on how far the KitKat install proceeded before failing -
-- Solution #3 - Severe - Factory Reset --
1) Download the stock SBF firmware for your pre-KitKat ROM (sbf.droid-developers.org).
2) Unzip the ROM and edit the XML file. Delete the step operation that says "getVar". It should be the first line under step operations.
3) Use RSD lite to flash the firmware
- This will erase EVERYTHING. Say goodbye to your data. And porn.
Hope you get to recover using only the first two steps. If not, rinse then repeat. Good luck!
Click to expand...
Click to collapse
OK, I got past the previous error by increasing the RAM allocated to my Windows VM. Now I get the following error when running "fastboot flash system system.img":
sending 'system' (850189 KB)...
(bootloader) Data size exceeds download buffer
FAILED (remote failure)
finished. total time: 0.313s
cbridgers said:
Thanks for your detailed instructions! Solution #1 didn't work for me. Solution #2 gives me the following error when I run "fastboot flash system system.img":
load_file: could not allocate 870593756 bytes
error: cannot load 'system.img'
I'm not sure I want to try Solution #3 yet. May try to talk to Motorola first.
Thanks again for the detailed advice!
Chris
Click to expand...
Click to collapse
Make sure you are using the newest fastboot files, the older ones do not chunk the system image and it is too large to flash.
New fastboot for Mac -- > http://www.teamblackhat.net/Downloads/Darwin.zip
New fastboot for Windows --> http://www.teamblackhat.net/Downloads/fastboot.zip
Use the house if moto save data option you can fxz using rsd or fastboot and it will not erase data at all. I have used it many times works great.
SamSpadeXX said:
I had the same issue. I was able to recover it once, but recreated the scenario for good measures. My best guess is this issue is free space related (you should have at least 3gb free), but I'll confirm later today.
Click to expand...
Click to collapse
How sure are you about this?
Also, I had xt1058 (americamovil) with TMO firmware with the camera update (unlocked BL) and I flashed stock vzw firmware (with the camera update). No problems after a full wipe. The OTA was downloading too slow so I downloaded the OTA zip file in other thread. When I tried to install the update via stock recovery i got this message:
"/modem/image/dsps.b00" has unexpected contents.
Installation aborted
Click to expand...
Click to collapse
So i waited for the normal OTA and it just says installation failed, and i had it just wiped so i can't be free space.
Finally I flashed the 4.4 TMO leak
Try this
fastboot oem fb_mode_clear
fastboot reboot-bootloader
then take all the files from the first OTA sbf and flash them in order
does that work?
waiflih said:
How sure are you about this?
Also, I had xt1058 (americamovil) with TMO firmware with the camera update (unlocked BL) and I flashed stock vzw firmware (with the camera update). No problems after a full wipe. The OTA was downloading too slow so I downloaded the OTA zip file in other thread. When I tried to install the update via stock recovery i got this message:
So i waited for the normal OTA and it just says installation failed, and i had it just wiped so i can't be free space.
Finally I flashed the 4.4 TMO leak
Click to expand...
Click to collapse
There are 5 parts that need to be stock, that is the only thing that needs to be done.
system, boot, recovery, modem, fsg.
the only way to know why it is failing is to sideload, load from recovery, or check the update error log.
If it were me I'd just fastboot all five of those partitions and take the update.
jimmydafish said:
There are 5 parts that need to be stock, that is the only thing that needs to be done.
system, boot, recovery, modem, fsg.
the only way to know why it is failing is to sideload, load from recovery, or check the update error log.
If it were me I'd just fastboot all five of those partitions and take the update.
Click to expand...
Click to collapse
I dont know where to find modem files for stock vzw
Enviado desde mi XT1052
waiflih said:
I dont know where to find modem files for stock vzw
Enviado desde mi XT1052
Click to expand...
Click to collapse
They are in the FXZ file named NON-HLOS.bin
Thx! I didnt know those were modem related. Can i flash back the modem files to tmo or att firmware?
Enviado desde mi XT1052
waiflih said:
Thx! I didnt know those were modem related. Can i flash back the modem files to tmo or att firmware?
Enviado desde mi XT1052
Click to expand...
Click to collapse
Well what are you trying to do? but if unlocked you can flash anything you want. I would stay far away from flashing any bootloader, tz, gpt, or sbl files though.
Only flash those files I named before.
Yes, i only flash the files i know are safe to flash, i dont like to use rsdlite. Thx again
Enviado desde mi XT1052
I seem to have run into the same issue..
Any updates, OP?
Here's my thread: http://forum.xda-developers.com/showthread.php?p=47747140#post47747140
ekraincg said:
I seem to have run into the same issue..
Any updates, OP?
Here's my thread: http://forum.xda-developers.com/showthread.php?p=47747140#post47747140
Click to expand...
Click to collapse
I'm having the same problem with my T-Mo moto x I received yesterday. I tried the fastboot erase cache method. It works to the extent that I can boot back into 4.2.2 but I can't update or perform a factory reset from the settings menu.
When I give the command to fastboot erase cache the bootloader says 'get-var partition type' and 'erasing cache' however the bootloader never says 'cache erased' or any other confirmation message. Fastboot on the desktop does say 'cache erased' though.
Finally, I would try to flash the stock images but I can't seem to find them anywhere. Can someone point me to them please?
So one of my buddies took the OTA update for 4.4.2 while being rooted on 4.4 with TWRP as his recovery. Now he is stuck in an endless bootloop. Any idea what we could do to bring his phone back to life?
By the way, he is on Sprint and has his bootloader unlocked
Any advice would help!
Thanks.
AbstractXart said:
So one of my buddies took the OTA update for 4.4.2 while being rooted on 4.4 with TWRP as his recovery. Now he is stuck in an endless bootloop. Any idea what we could do to bring his phone back to life?
By the way, he is on Sprint and has his bootloader unlocked
Any advice would help!
Thanks.
Click to expand...
Click to collapse
This happened to me too.
Just flash the latest firmware for your device at http://sbf.droid-developers.org/phone.php?device=0
Then accept the OTA.
Re-install TWRP.
Hope this works for you too.
patspdaphone said:
This happened to me too.
Just flash the latest firmware for your device at http://sbf.droid-developers.org/phone.php?device=0
Then accept the OTA.
Re-install TWRP.
Hope this works for you too.
Click to expand...
Click to collapse
So to accept the OTA, did you go through the bootloader/recovery and flash it, or were you able to turn on your phone and accept it? Sorry I don't have his phone on me right now otherwise I would have done it .
Don't flash the full SBF..
boot the phone into fastboot mode... mfastboot erase cache... the reboot the phone. that will remove the OTA zip file from chache and stop the boot loop.
The bootloop is because the phone has TWRP on it rather than stock recovery.
To take the OTA properly, use mfastboot to reflash stock recovery only. Also have him undo any hacks that might have touched system files or the OTA will fail, (mfastboot system will also get /system back to normal)...
KidJoe said:
Don't flash the full SBF..
boot the phone into fastboot mode... mfastboot erase cache... the reboot the phone. that will remove the OTA zip file from chache and stop the boot loop.
The bootloop is because the phone has TWRP on it rather than stock recovery.
To take the OTA properly, use mfastboot to reflash stock recovery only. Also have him undo any hacks that might have touched system files or the OTA will fail, (mfastboot system will also get /system back to normal)...
Click to expand...
Click to collapse
We actually just ended up clearing the system cache and that seemed to do the trick .
I incredibly appreciate all the info! If anyone makes this silly mistake, all you need to do is clear the cache and everything works as intended.
AbstractXart said:
We actually just ended up clearing the system cache and that seemed to do the trick .
I incredibly appreciate all the info! If anyone makes this silly mistake, all you need to do is clear the cache and everything works as intended.
Click to expand...
Click to collapse
until the next time the OTA downloads and tries to install
I am having this very same problem. My phone just today went into boot loop. Running KangKat on unlocked 1053 with Faux kernel. No boot logo or anything. The phone just vibrates then after 30 seconds or so, it vibrates again. It does this non-stop.
I can plug my phone into USB and the phone's contents come up on my computer, but I can't get the screen to turn on!! Any ideas?
Globalrebel said:
I am having this very same problem. My phone just today went into boot loop. Running KangKat on unlocked 1053 with Faux kernel. No boot logo or anything. The phone just vibrates then after 30 seconds or so, it vibrates again. It does this non-stop.
I can plug my phone into USB and the phone's contents come up on my computer, but I can't get the screen to turn on!! Any ideas?
Click to expand...
Click to collapse
KangKat wtih Faux kernel? So you are not running the stock rom? I'm suprised the actually OTA installed.
I don't know anything about that rom, or kernel to begin to tell you how to fix this situation, short of reflashing your rom
KidJoe said:
KangKat wtih Faux kernel? So you are not running the stock rom? I'm suprised the actually OTA installed.
I don't know anything about that rom, or kernel to begin to tell you how to fix this situation, short of reflashing your rom
Click to expand...
Click to collapse
He probably flashed the "Flashable 4.4.2 ZIP" that is flashable through TWRP.
@Globalrebel :
You need to try to get into bootloader (AP Fastboot) mode. Try holding the VOL DOWN while the phone reboots (vibrates). Make sure the phone is unplugged from USB. If you can access fastboot, your best best would probably to flash the entire SBF back to stock.
Always check here first before you do something like trying to flash a stock update on a custom rom. We would have quickly informed you that this is ill-advised.
Good Luck
Ok, so I have held down the power button, and then when vibrating starts, I hold down vol down button. Then, it vibrates 2 times. What now? (Sorry, I'm freaked out as this is my only phones )
How can i check to see if it is actually in Fastboot mode? Since my screen doesn't show ANYTHING at all?
I started up an ADB server and connected my phone and tried "adb devices" but my phone isn't listed.
---------- Post added at 08:49 AM ---------- Previous post was at 08:40 AM ----------
samwathegreat said:
He probably flashed the "Flashable 4.4.2 ZIP" that is flashable through TWRP.
@Globalrebel :
You need to try to get into bootloader (AP Fastboot) mode. Try holding the VOL DOWN while the phone reboots (vibrates). Make sure the phone is unplugged from USB. If you can access fastboot, your best best would probably to flash the entire SBF back to stock.
Always check here first before you do something like trying to flash a stock update on a custom rom. We would have quickly informed you that this is ill-advised.
Good Luck
Click to expand...
Click to collapse
any ideas?
I just checked device manager and it shows "ADB Interface" and then MOT Single ADB Interface.
But its not showing up under devices when running command "ADB Devices" in CMD
Globalrebel said:
Ok, so I have held down the power button, and then when vibrating starts, I hold down vol down button. Then, it vibrates 2 times. What now? (Sorry, I'm freaked out as this is my only phones )
How can i check to see if it is actually in Fastboot mode? Since my screen doesn't show ANYTHING at all?
I started up an ADB server and connected my phone and tried "adb devices" but my phone isn't listed.
---------- Post added at 08:49 AM ---------- Previous post was at 08:40 AM ----------
any ideas?
Click to expand...
Click to collapse
Fastboot getvar all
If you get a response with that, proceed with the entire Sbf manual method as listed in the return to stock thread.
samwathegreat said:
Fastboot getvar all
If you get a response with that, proceed with the entire Sbf manual method as listed in the return to stock thread.
Click to expand...
Click to collapse
I got it to show some info after running the command. Now, I have the following guide open . .
[GUIDE][VIDEO] Moto X - Return to 100% stock (using RSD Lite OR manual flash)
But I don't see anything in RSDLite after running it and clicking "Show Device"
Can I just to the manual method?
For manual method, should I copy all the files into the same folder as my mfastboot.exe?
Globalrebel said:
I got it to show some info after running the command. Now, I have the following guide open . .
[GUIDE][VIDEO] Moto X - Return to 100% stock (using RSD Lite OR manual flash)
But I don't see anything in RSDLite after running it and clicking "Show Device"
Can I just to the manual method?
For manual method, should I copy all the files into the same folder as my mfastboot.exe?
Click to expand...
Click to collapse
Yes,I suggested manual method in last post. Faster and easier.
Yes extract the sbf to the folder containing mfastboot and fastboot.
The only thing you will do differently is one of the last lines that says carrier vzw, change it to carrier sprint.
Make sure u are using the 4.4.2 sprint sbf.
Good luck
samwathegreat said:
Yes,I suggested manual method in last post. Faster and easier.
Yes extract the sbf to the folder containing mfastboot and fastboot.
The only thing you will do differently is one of the last lines that says carrier vzw, change it to carrier sprint.
Make sure u are using the 4.4.2 sprint sbf.
Good luck
Click to expand...
Click to collapse
I am using Tmobile so I put tmo
But, after doing EVERYTHING, the phone reboots and I see it in PC, but screen is still not working?!?!?!
I did everything...
fastboot oem fb_mode_set
fastboot flash partition gpt.bin
fastboot flash motoboot motoboot.img
fastboot flash logo logo.bin
fastboot flash boot boot.img
fastboot flash recovery recovery.img
mfastboot flash system system.img
fastboot flash modem NON-HLOS.bin
fastboot erase modemst1
fastboot erase modemst2
fastboot flash fsg fsg.mbn
fastboot erase cache
fastboot erase userdata
fastboot erase customize
fastboot erase clogo
fastboot oem config carrier tmo
fastboot oem fb_mode_clear
then
fastboot reboot
The phone boots and the phone is seen by my computer, but the screen is not working AT ALL
No water damage, and the phone was literally working perfectly fine 15 minutes ago. Just all of a sudden stopped showing the screen
Globalrebel said:
I am using Tmobile so I put tmo
But, after doing EVERYTHING, the phone reboots and I see it in PC, but screen is still not working?!?!?!
I did everything...
fastboot oem fb_mode_set
fastboot flash partition gpt.bin
fastboot flash motoboot motoboot.img
fastboot flash logo logo.bin
fastboot flash boot boot.img
fastboot flash recovery recovery.img
mfastboot flash system system.img
fastboot flash modem NON-HLOS.bin
fastboot erase modemst1
fastboot erase modemst2
fastboot flash fsg fsg.mbn
fastboot erase cache
fastboot erase userdata
fastboot erase customize
fastboot erase clogo
fastboot oem config carrier tmo
fastboot oem fb_mode_clear
then
fastboot reboot
The phone boots and the phone is seen by my computer, but the screen is not working AT ALL
Click to expand...
Click to collapse
Bummer. You appear to have used the correct procedure.
This looks to be a hardware failure :/
Sorry, I don't have any further troubleshooting techniques for you...
Its all good. I think the screen just decided to die on me?!?! Which REALLY SUCKS! I'm still in my 1 year warranty policy. After fastbooting the original 4.4.2, will motorola know I did anything to the phone? IE, can they know I flashed anything?
Globalrebel said:
Its all good. I think the screen just decided to die on me?!?! Which REALLY SUCKS! I'm still in my 1 year warranty policy. After fastbooting the original 4.4.2, will motorola know I did anything to the phone? IE, can they know I flashed anything?
Click to expand...
Click to collapse
If you unlocked the bootloader they know it. Technically your warranty is void... But they might replace/fix it anyways. Don't mention it and see what happens. Let us know.
I have read the threads on the latest OTA update for the Pure Edition and I am confused on how to proceed. I am running System Version 22.11.6 Build Number LXE22.39.-6 and have got an OTA for 22.21.11.en.US, but it has failed of course. I am rooted with CF-Auto Root, the version from the middle of November, and have stock recovery.
What I am seeking to do is update to 22.21.11.en.US and not lose my apps or data.
What is the correct procedure for updating? Thanks Guys!!
I was on the first soak test build for lollipop and when the .6 build came out (the one that your on) I couldn't update unless I downgraded to 4.4.4 then re upgraded to lollipop OTA but it took a day for the OTA to show on my phone .....im pretty sure you have to do the same from .6 to .11 so https://motorola-global-portal.custhelp.com/app/standalone/bootloader/recovery-images follow the steps on Motorola's website here really simple process just a few commands, but it will wipe your device
Since you're rooted, just run Titanium backup, return to 4.4.4, then apply .6 update and .11 update. (The .11 we have so far is only a delta from .6 -- not the full OTA)
edit: Apparently the full kitkat->lollipop .11 OTA is out there... hooray!
Do not use the instructions on Motorola factory images website
That website is missing a subtle command, that will make your OTA fail. I had that problem.
This line is missing.
fastboot flash modem NON-HLOS.bin
The OTA checks for the integrity of the modem and fails otherwise.
---------- Post added at 12:40 PM ---------- Previous post was at 12:31 PM ----------
Matthewlawson3 said:
What I am seeking to do is update to 22.21.11.en.US and not lose my apps or data.
Click to expand...
Click to collapse
You can try ADB backup for backing up all your apps and restore after OTA. This way the restore process works even after unrooting.
nimper said:
Since you're rooted, just run Titanium backup, return to 4.4.4, then apply .6 update and .11 update. (The .11 we have so far is only a delta from .6 -- not the full OTA)
edit: Apparently the full kitkat->lollipop .11 OTA is out there... hooray!
Click to expand...
Click to collapse
Android.is.better94 said:
I was on the first soak test build for lollipop and when the .6 build came out (the one that your on) I couldn't update unless I downgraded to 4.4.4 then re upgraded to lollipop OTA but it took a day for the OTA to show on my phone .....im pretty sure you have to do the same from .6 to .11 so https://motorola-global-portal.custhelp.com/app/standalone/bootloader/recovery-images follow the steps on Motorola's website here really simple process just a few commands, but it will wipe your device
Click to expand...
Click to collapse
I was rooted on .6 and had to go to 4.4.4. I received the OTA to .11. It was a 576 MB or so update. So there are 2 update OTA depending on what version you are running.
Questions and Requests
bradley26 said:
I was rooted on .6 and had to go to 4.4.4. I received the OTA to .11. It was a 576 MB or so update. So there are 2 update OTA depending on what version you are running.
Click to expand...
Click to collapse
Ok. I have a few questions and requests.
First, this would be my first downgrade I have ever done, do I have to relock the bootloader and/or unroot first?
Second, what are the exact steps and commands in order to downgrade. I know you said they are Motorola's website, but just to be safe, and with the modem command added in, I would feel much better and be appreciative if someone provided that for me.
Third, I am on the US pure edition, which version of 4.4.4. would I need to download from Motorola's website? I've forgotten which version it came with.
Fourth, I was never a soak tester and I am on .6. Why can't I do a direct upgrade to .11 such as what is discussed here?
http://forum.xda-developers.com/moto-x-2014/general/ota-pure-edition-lollipop-5-0-t2932625
Another Approach?
And what about this approach to upgrading from .6. to .11? Could this work?
http://forum.xda-developers.com/moto-x-2014/general/guide-update-xt1095-pure-edition-to-t2937074
Matthewlawson3 said:
Ok. I have a few questions and requests.
First, this would be my first downgrade I have ever done, do I have to relock the bootloader and/or unroot first?
Second, what are the exact steps and commands in order to downgrade. I know you said they are Motorola's website, but just to be safe, and with the modem command added in, I would feel much better and be appreciative if someone provided that for me.
Third, I am on the US pure edition, which version of 4.4.4. would I need to download from Motorola's website? I've forgotten which version it came with.
Fourth, I was never a soak tester and I am on .6. Why can't I do a direct upgrade to .11 such as what is discussed here?
http://forum.xda-developers.com/moto-x-2014/general/ota-pure-edition-lollipop-5-0-t2932625
Click to expand...
Click to collapse
For whatever reason you can never have been rooted to update your ROM. So i followed the steps below to get back to stock for the update.
Go to http://www.graffixnyc.com/motox.php and grab the 4.4.4 stock image. Extract and place in platforms-tools folder with fastboot.
After downloading the image for your device:
Put your device in fastboot mode.
NOTE: You must use the Motorola fastboot utility to flash (included in the Darwin/, Linux/ or Windows/ directory). Please do NOT use the Android fastboot utility
Follow the flashing steps in the .xml file that was included in the package.
A typical flashing sequence includes all these partitions, but might vary depending on your product - so please use the sequence in the .xml file in your package:
$ fastboot flash partition gpt.bin
$ fastboot flash motoboot motoboot.img
$ fastboot reboot-bootloader
$ fastboot flash logo logo.bin
$ fastboot flash boot boot.img
$ fastboot flash recovery recovery.img
$ fastboot flash system system.img
$ fastboot erase modemst1
$ fastboot erase modemst2
$ fastboot flash fsg fsg.mbn
$ fastboot reboot
You also have the option to erase all the data on your device with
$ fastboot erase userdata
$ fastboot erase cache
Hope this helps. Copied and pasted the commands from Motorola.
bradley26 said:
For whatever reason you can never have been rooted to update your ROM. So i followed the steps below to get back to stock for the update.
Go to http://www.graffixnyc.com/motox.php and grab the 4.4.4 stock image. Extract and place in platforms-tools folder with fastboot.
After downloading the image for your device:
Put your device in fastboot mode.
NOTE: You must use the Motorola fastboot utility to flash (included in the Darwin/, Linux/ or Windows/ directory). Please do NOT use the Android fastboot utility
Follow the flashing steps in the .xml file that was included in the package.
A typical flashing sequence includes all these partitions, but might vary depending on your product - so please use the sequence in the .xml file in your package:
$ fastboot flash partition gpt.bin
$ fastboot flash motoboot motoboot.img
$ fastboot reboot-bootloader
$ fastboot flash logo logo.bin
$ fastboot flash boot boot.img
$ fastboot flash recovery recovery.img
$ fastboot flash system system.img
$ fastboot erase modemst1
$ fastboot erase modemst2
$ fastboot flash fsg fsg.mbn
$ fastboot reboot
You also have the option to erase all the data on your device with
$ fastboot erase userdata
$ fastboot erase cache
Hope this helps. Copied and pasted the commands from Motorola.
Click to expand...
Click to collapse
@Matthewlawson3
you can't downgrade the bootloader so omit that step. it won't make the OTA fail.
i'd recommend erasing userdata and cache.
once you do this, you should get the official full OTA that you can check for in the settings menu and apply. good luck.
mrvirginia said:
@Matthewlawson3
you can't downgrade the bootloader so omit that step. it won't make the OTA fail.
i'd recommend erasing userdata and cache.
once you do this, you should get the official full OTA that you can check for in the settings menu and apply. good luck.
Click to expand...
Click to collapse
So motoboot.img is the bootloader? That is the command you don't want me to enter?
I need to type in all the commands in that exact sequence, correct? Where does one enter the fastboot flash modem NON-HLOS.bin in the sequence of commands?
I would prefer not to lose my apps and data if it can be avoided. I do have Titanium Backup and could if need be, but what are the downsides to not erasing usercache and cache?
Thanks for your help on this!!!
Motorola Fastboot
I've never used the Motorola Fastboot utility. How does one acquire it and how do you set it up? I've only use the Android fastboot in the platform-tools folder.
Also, which build of 4.4.4. do I choose from on graffinxnyc's website? 4.4.4 Build: KXE21.187-42 Full Restore Images?
Matthewlawson3 said:
I've never used the Motorola Fastboot utility. How does one acquire it and how do you set it up? I've only use the Android fastboot in the platform-tools folder.
Also, which build of 4.4.4. do I choose from on graffinxnyc's website? 4.4.4 Build: KXE21.187-42 Full Restore Images?
Click to expand...
Click to collapse
fastboot flash partition gpt.bin
fastboot reboot-bootloader
fastboot flash logo logo.bin
fastboot flash boot boot.img
fastboot flash recovery recovery.img
fastboot flash system system.img
fastboot erase modemst1
fastboot erase modemst2
fastboot flash fsg fsg.mbn
fastboot flash modem NON-HLOS.bin
fastboot erase userdata
fastboot erase cache
fastboot reboot
I got the images from motos site. had everything I needed.
not sure what, if any, errors you'd see due to not erasing userdata/cache
mrvirginia said:
fastboot flash partition gpt.bin
fastboot reboot-bootloader
fastboot flash logo logo.bin
fastboot flash boot boot.img
fastboot flash recovery recovery.img
fastboot flash system system.img
fastboot erase modemst1
fastboot erase modemst2
fastboot flash fsg fsg.mbn
fastboot flash modem NON-HLOS.bin
fastboot erase userdata
fastboot erase cache
fastboot reboot
I got the images from motos site. had everything I needed.
not sure what, if any, errors you'd see due to not erasing userdata/cache
Click to expand...
Click to collapse
I have got the image for 4.4.4 (TMO_21.21.42.victara_tmo.tmo.en.US) from Motorola for the US Pure Edition, through the request process. Can I run these commands using regular fastboot from the android SDK platform-tools folder or must I use fastboot found in the Motorola 4.4.4 image? If I must use Motorola fastboot, what is the process for getting that setup before I go into a command prompt and enter the commands?
If I use the Motorola fastboot can I just copy the needed files into the Windows folder found in the Motorola image folder and then open a command prompt there to enter the commands? Is it that easy? I do not have a mfastboot file in the Windows folder in the image.
Matthewlawson3 said:
I have got the image for 4.4.4 (TMO_21.21.42.victara_tmo.tmo.en.US) from Motorola for the US Pure Edition, through the request process. Can I run these commands using regular fastboot from the android SDK platform-tools folder or must I use fastboot found in the Motorola 4.4.4 image? If I must use Motorola fastboot, what is the process for getting that setup before I go into a command prompt and enter the commands?
If I use the Motorola fastboot can I just copy the needed files into the Windows folder found in the Motorola image folder and then open a command prompt there to enter the commands? Is it that easy? I do not have a mfastboot file in the Windows folder in the image.
Click to expand...
Click to collapse
After doing some research, I have placed the fastboot.exe from the Motorola image in the Android-SDK platform-tools folder, but before I placed it in there, I renamed it mfastboot.exe, so as not to clash with the android fastboot.exe. When I type in the command prompt "mfastboot," I get a list of commands. Does this indicate everything is working correctly? And if so, when I type in the commands to perform the downgrade will I type in "mfastboot" instead of "fastboot" with every command?
Matthewlawson3 said:
After doing some research, I have placed the fastboot.exe from the Motorola image in the Android-SDK platform-tools folder, but before I placed it in there, I renamed it mfastboot.exe, so as not to clash with the android fastboot.exe. When I type in the command prompt "mfastboot," I get a list of commands. Does this indicate everything is working correctly? And if so, when I type in the commands to perform the downgrade will I type in "mfastboot" instead of "fastboot" with every command?
Click to expand...
Click to collapse
yes and yes
Ok. Thanks! One last question regarding the commands. After I flash partition gpt.bin, I am suppose to reboot from fastboot back to fastboot (reboot-bootloader) before continuing the commands..correct?
I downloaded the flashable zip from https://www.androidfilehost.com/?fid=95851846488293411
I use WugToolKit with TWRP, Unlocked and Decrypted. Stock ROM
I'm confused as to how I should flash this, I've read I should just click flash zip in the toolkit and let it finish and done. Also that I could download the file to my phone and use TWRP to flash straight to the phone. Some say backup and some say don't. Also some threads say I need to flash back to factory image, tho this flashable zip should be a factory image of 5.0.1.
Any help will be appreciated. Thank you.
Sent from my Nexus 6
SoCoCapricorn said:
I downloaded the flashable zip from https://www.androidfilehost.com/?fid=95851846488293411
I use WugToolKit with TWRP, Unlocked and Decrypted. Stock ROM
I'm confused as to how I should flash this, I've read I should just click flash zip in the toolkit and let it finish and done. Also that I could download the file to my phone and use TWRP to flash straight to the phone. Some say backup and some say don't. Also some threads say I need to flash back to factory image, tho this flashable zip should be a factory image of 5.0.1.
Any help will be appreciated. Thank you.
Sent from my Nexus 6
Click to expand...
Click to collapse
Apparently the new update OTA or zip will update blocks instead of files so from my understanding, even the slightest change from stock will cause this ZIP to fail when flashing. I'm rooted, decrypted, and changed mixer_paths.xml and as expected the flash failed in TWRP and adb sideload so I'm backing up via Titanium and flashing the 5.0.1 stock. I'll decrypt/root/restore after the flash.
Here are the steps I took to flash the factory image and not lose my settings:
Flash bootloader and radio:
fastboot flash bootloader bootloader-shamu-moto-apq8084-71.05.img
fastboot flash radio radio-shamu-d4.0-9625-02.55.04.img
After flashing the bootloader/radio, you need to reboot the bootloader as shown below, don't skip this step!
fastboot reboot-bootloader
I then unzipped this file: image-shamu-lrx22c.zip
Now you can move on to the rest of the files
fastboot flash recovery recovery.img
fastboot flash boot boot.img
fastboot flash system system.img
Finally, just reboot your device, and Android should start up.
fastboot reboot
After the phone restarted I then used CF-Auto-Root to re-root my phone. I did not lose any of my settings or installed apps. HTH...
So if I am stock but rooted I cannot sideload the OTA?
I keep getting status 7 error when trying to sideload with ADB using the update OTA.
It actual unzips and installs about 50% and then I get the Status 7 Error
mzimand said:
So if I am stock but rooted I cannot sideload the OTA?
I keep getting status 7 error when trying to sideload with ADB using the update OTA.
It actual unzips and installs about 50% and then I get the Status 7 Error
Click to expand...
Click to collapse
Rooting causes a change to the system partition, so no, you can't sideload the OTA anymore. (not since Lollipop)
stevetrooper said:
Here are the steps I took to flash the factory image and not lose my settings:
Flash bootloader and radio:
fastboot flash bootloader bootloader-shamu-moto-apq8084-71.05.img
fastboot flash radio radio-shamu-d4.0-9625-02.55.04.img
After flashing the bootloader/radio, you need to reboot the bootloader as shown below, don't skip this step!
fastboot reboot-bootloader
I then unzipped this file: image-shamu-lrx22c.zip
Now you can move on to the rest of the files
fastboot flash recovery recovery.img
fastboot flash boot boot.img
fastboot flash system system.img
Finally, just reboot your device, and Android should start up.
fastboot reboot
After the phone restarted I then used CF-Auto-Root to re-root my phone. I did not lose any of my settings or installed apps. HTH...
Click to expand...
Click to collapse
Worked like a CHAMP!!
:highfive:
stevetrooper said:
Here are the steps I took to flash the factory image and not lose my settings:
Flash bootloader and radio:
fastboot flash bootloader bootloader-shamu-moto-apq8084-71.05.img
fastboot flash radio radio-shamu-d4.0-9625-02.55.04.img
After flashing the bootloader/radio, you need to reboot the bootloader as shown below, don't skip this step!
fastboot reboot-bootloader
I then unzipped this file: image-shamu-lrx22c.zip
Now you can move on to the rest of the files
fastboot flash recovery recovery.img
fastboot flash boot boot.img
fastboot flash system system.img
Finally, just reboot your device, and Android should start up.
fastboot reboot
After the phone restarted I then used CF-Auto-Root to re-root my phone. I did not lose any of my settings or installed apps. HTH...
Click to expand...
Click to collapse
Are you using nexus toolkit by wug?
Sent from my Nexus 6
SoCoCapricorn said:
Are you using nexus toolkit by wug?
Sent from my Nexus 6
Click to expand...
Click to collapse
No, just used the steps I listed.
SoCoCapricorn said:
Are you using nexus toolkit by wug?
Sent from my Nexus 6
Click to expand...
Click to collapse
No, he used fastboot. Be wary of toolkits. They can do damage that a novice wont be able to fix.
stevetrooper said:
Here are the steps I took to flash the factory image and not lose my settings:
Flash bootloader and radio:
fastboot flash bootloader bootloader-shamu-moto-apq8084-71.05.img
fastboot flash radio radio-shamu-d4.0-9625-02.55.04.img
After flashing the bootloader/radio, you need to reboot the bootloader as shown below, don't skip this step!
fastboot reboot-bootloader
I then unzipped this file: image-shamu-lrx22c.zip
Now you can move on to the rest of the files
fastboot flash recovery recovery.img
fastboot flash boot boot.img
fastboot flash system system.img
Finally, just reboot your device, and Android should start up.
fastboot reboot
After the phone restarted I then used CF-Auto-Root to re-root my phone. I did not lose any of my settings or installed apps. HTH...
Click to expand...
Click to collapse
Jeezus! perfect!
Thats similar to what I did.
Only thing to do if you are already decrypted is to download this boot file, rename it to boot.img and flash it instead of the one included in the google zip package.
http://forum.xda-developers.com/showpost.php?p=57406510&postcount=360
I had to manually flash each file separately. For some reason when the flash.bat file was running it kept reporting that the system.img file was too big. Not had that before.
dunjamon said:
I had to manually flash each file separately. For some reason when the flash.bat file was running it kept reporting that the system.img file was too big. Not had that before.
Click to expand...
Click to collapse
yeah - since 5.0, the flash-all.bat isn't working for a lot of users.
stevetrooper said:
Here are the steps I took to flash the factory image and not lose my settings:
Flash bootloader and radio:
fastboot flash bootloader bootloader-shamu-moto-apq8084-71.05.img
fastboot flash radio radio-shamu-d4.0-9625-02.55.04.img
After flashing the bootloader/radio, you need to reboot the bootloader as shown below, don't skip this step!
fastboot reboot-bootloader
I then unzipped this file: image-shamu-lrx22c.zip
Now you can move on to the rest of the files
fastboot flash recovery recovery.img
fastboot flash boot boot.img
fastboot flash system system.img
Finally, just reboot your device, and Android should start up.
fastboot reboot
After the phone restarted I then used CF-Auto-Root to re-root my phone. I did not lose any of my settings or installed apps. HTH...
Click to expand...
Click to collapse
What about the cache.img? do we not flash the cache?
mzimand said:
What about the cache.img? do we not flash the cache?
Click to expand...
Click to collapse
From what I understand, if you flash cache.img, you will go back to stock and lose all of your settings.
Awesome man, worked perfect, you sir rock!
Great!!!!
stevetrooper said:
Here are the steps I took to flash the factory image and not lose my settings:
Flash bootloader and radio:
fastboot flash bootloader bootloader-shamu-moto-apq8084-71.05.img
fastboot flash radio radio-shamu-d4.0-9625-02.55.04.img
After flashing the bootloader/radio, you need to reboot the bootloader as shown below, don't skip this step!
fastboot reboot-bootloader
I then unzipped this file: image-shamu-lrx22c.zip
Now you can move on to the rest of the files
fastboot flash recovery recovery.img
fastboot flash boot boot.img
fastboot flash system system.img
Finally, just reboot your device, and Android should start up.
fastboot reboot
After the phone restarted I then used CF-Auto-Root to re-root my phone. I did not lose any of my settings or installed apps. HTH...
Click to expand...
Click to collapse
It works like a champ! THX man :good:
stevetrooper said:
Here are the steps I took to flash the factory image and not lose my settings:
Flash bootloader and radio:
fastboot flash bootloader bootloader-shamu-moto-apq8084-71.05.img
fastboot flash radio radio-shamu-d4.0-9625-02.55.04.img
After flashing the bootloader/radio, you need to reboot the bootloader as shown below, don't skip this step!
fastboot reboot-bootloader
I then unzipped this file: image-shamu-lrx22c.zip
Now you can move on to the rest of the files
fastboot flash recovery recovery.img
fastboot flash boot boot.img
fastboot flash system system.img
Finally, just reboot your device, and Android should start up.
fastboot reboot
After the phone restarted I then used CF-Auto-Root to re-root my phone. I did not lose any of my settings or installed apps. HTH...
Click to expand...
Click to collapse
Excellent, works perfectly as described. Thanks
The only thing that I'd add, to avoid any confusion, is that the factory image can be downloaded from:
https://developers.google.com/android/nexus/images
Thanks again, stevetrooper :good:
stevetrooper said:
Here are the steps I took to flash the factory image and not lose my settings:
Flash bootloader and radio:
fastboot flash bootloader bootloader-shamu-moto-apq8084-71.05.img
fastboot flash radio radio-shamu-d4.0-9625-02.55.04.img
After flashing the bootloader/radio, you need to reboot the bootloader as shown below, don't skip this step!
fastboot reboot-bootloader
I then unzipped this file: image-shamu-lrx22c.zip
Now you can move on to the rest of the files
fastboot flash recovery recovery.img
fastboot flash boot boot.img
fastboot flash system system.img
Finally, just reboot your device, and Android should start up.
fastboot reboot
After the phone restarted I then used CF-Auto-Root to re-root my phone. I did not lose any of my settings or installed apps. HTH...
Click to expand...
Click to collapse
Curious as to why so many steps?
All i did was flash the radio and system images. Went to 5.0.1 just fine, all settings/data retained.
Didn't flash bootloader, kept unlocked during process, only had to re-root.
Having an issue while flashing system.img file. I flashed radio, and flashed system.img then flashed cf-auto-root. On first start up I was having issues with my radio. LTE was not connecting to T Mobile. So I Nandroid back to stock. Then of course I noticed this didnt change my radio back to stock. Starting everything over, I reflashed radio, reboot bootloader, Flash system.img, reboot bootloader, then fash autoroot. Restart device. Radio was flashed and I had root, but stuck on 5.0 Tried to reflash system.img and I am getting error. "access denied" when flashing. I have read this is an issue with mounting the drive, I have even tried to do this in fast boot but I am coming up with nothing. Any help on this will be greatly appreciated.
theblizzard2010 said:
Curious as to why so many steps?
All i did was flash the radio and system images. Went to 5.0.1 just fine, all settings/data retained.
Didn't flash bootloader, kept unlocked during process, only had to re-root.
Click to expand...
Click to collapse
So, is there a way to flash the update to 5.0.1? I'm unlocked, rooted, and still encrypted. I want to stay encrypted. Sorry, just my own paranoia I guess. But is there a way to do it as an update without wiping the device and having to restore a backup? I have had too many backups fail in the past, and I'm kinda lazy. Plus its been a long time since I played with flashing an Android. since my old EVO 4G. LOL Thanks all. Oh yeah, if it matters, I'm on a T-Mobile Nexus 6.
scothern99 said:
So, is there a way to flash the update to 5.0.1? I'm unlocked, rooted, and still encrypted. I want to stay encrypted. Sorry, just my own paranoia I guess. But is there a way to do it as an update without wiping the device and having to restore a backup? I have had too many backups fail in the past, and I'm kinda lazy. Plus its been a long time since I played with flashing an Android. since my old EVO 4G. LOL Thanks all. Oh yeah, if it matters, I'm on a T-Mobile Nexus 6.
Click to expand...
Click to collapse
The flash-all.bat script doesn't work anyway, so don't use it. Just use fastboot and flash:
fastboot flash bootloader bootloader-shamu-moto-apq8084-71.05.img
fastboot reboot-bootloader
(wait for reboot)
fastboot flash radio radio-shamu-d4.0-9625-02.55.04.img
fastboot reboot-bootloader
(wait for reboot)
fastboot flash boot boot.img
fastboot flash recovery recovery.img
fastboot flash system system.img
Then, I like to boot directly into twrp and flash supersu.zip to reroot (I don't flash twrp on, just boot into it)
fastboot boot openrecovery-twrp-2.8.2.0-shamu.img
---------- Post added at 02:12 PM ---------- Previous post was at 02:02 PM ----------
You can turn that into a simple bat file to use if you like. Just copy and past the following (in between dashes) into notepad and save as something like nexus-flash.bat:
--------------------------
PATH=%PATH%;"%SYSTEMROOT%\System32"
fastboot flash bootloader bootloader-shamu-moto-apq8084-71.05.img
fastboot reboot-bootloader
ping -n 5 127.0.0.1 >nul
fastboot flash radio radio-shamu-d4.0-9625-02.55.04.img
fastboot reboot-bootloader
ping -n 5 127.0.0.1 >nul
fastboot flash boot boot.img
fastboot flash recovery recovery.img
fastboot flash system system.img
fastboot boot openrecovery-twrp-2.8.2.0-shamu.img
echo Press any key to exit...
pause >nul
exit
---------------------------------------
If you have named the twrp recovery something other than what it downloads as, be sure to adjust the file name in the script.
This assumes that all the files are in the same folder including the platform tools. So you would need to extract everything into the same folder.
livinginkaos said:
The flash-all.bat script doesn't work anyway, so don't use it. Just use fastboot and flash:
fastboot flash bootloader bootloader-shamu-moto-apq8084-71.05.img
fastboot reboot-bootloader
(wait for reboot)
fastboot flash radio radio-shamu-d4.0-9625-02.55.04.img
fastboot reboot-bootloader
(wait for reboot)
fastboot flash boot boot.img
fastboot flash recovery recovery.img
fastboot flash system system.img
Then, I like to boot directly into twrp and flash supersu.zip to reroot (I don't flash twrp on, just boot into it)
fastboot boot openrecovery-twrp-2.8.2.0-shamu.img
---------- Post added at 02:12 PM ---------- Previous post was at 02:02 PM ----------
You can turn that into a simple bat file to use if you like. Just copy and past the following (in between dashes) into notepad and save as something like nexus-flash.bat:
--------------------------
PATH=%PATH%;"%SYSTEMROOT%\System32"
fastboot flash bootloader bootloader-shamu-moto-apq8084-71.05.img
fastboot reboot-bootloader
ping -n 5 127.0.0.1 >nul
fastboot flash radio radio-shamu-d4.0-9625-02.55.04.img
fastboot reboot-bootloader
ping -n 5 127.0.0.1 >nul
fastboot flash boot boot.img
fastboot flash recovery recovery.img
fastboot flash system system.img
fastboot boot openrecovery-twrp-2.8.2.0-shamu.img
echo Press any key to exit...
pause >nul
exit
---------------------------------------
If you have named the twrp recovery something other than what it downloads as, be sure to adjust the file name in the script.
This assumes that all the files are in the same folder including the platform tools. So you would need to extract everything into the same folder.
Click to expand...
Click to collapse
Ok, so not to be a noob, where do I get the image files to flash?
Nexus images are all posted here - https://developers.google.com/android/nexus/images
Ok, so I used the toolkit to unlock/root, I'm assuming then that to use this script you posted, I would need to download the actual ADB/Fastboot files separately?
Sorry for the stupid questions, I'm learning all over again, and this is my first Nexus device.
EDIT: So it looks like I can use the toolkit to individually flash the system image and then the radio. Will that work doing it in that order?
scothern99 said:
Ok, so I used the toolkit to unlock/root, I'm assuming then that to use this script you posted, I would need to download the actual ADB/Fastboot files separately?
Sorry for the stupid questions, I'm learning all over again, and this is my first Nexus device.
EDIT: So it looks like I can use the toolkit to individually flash the system image and then the radio. Will that work doing it in that order?
Click to expand...
Click to collapse
Does anyone know if this is correct?
What I did to upgrade without wiping, i was on stock with elementalx kernel, root and twrp.
Only flashed radio and system img.
1. Downloaded images, extracted zip of the images.
2. Reboot to bootloader
3. Fastboot commands
fastboot flash radio radio-shamu-d4.0-9625-02.55.04.img
fastboot reboot-bootloader
fastboot flash system system.img
fastboot reboot
4. Reboot to bootloader again
Run chainfire autoroot script.
5. Done
Remember to read read read if you don't know what are you doing, nobody here is responsible if things go wrong.
With my past phones, there was always a stock rom posted shortly after the update came out. I would just flash that over what I had already to update. Is there some reason why no one has posted any stock roms for the nexus 6?
lion1750 said:
With my past phones, there was always a stock rom posted shortly after the update came out. I would just flash that over what I had already to update. Is there some reason why no one has posted any stock roms for the nexus 6?
Click to expand...
Click to collapse
I'm wondering the same. Usually it was out right away and I would do the same as you. Seems crazy to me that we would have to unroot update and reroot agaain.
Usually I would flash a stock rom with the update that the dev would also throw root into.
livinginkaos said:
Then, I like to boot directly into twrp and flash supersu.zip to reroot (I don't flash twrp on, just boot into it)
fastboot boot openrecovery-twrp-2.8.2.0-shamu.img
Click to expand...
Click to collapse
Can you do this as opposed to using the CF-Auto-Root-shamu-shamu-nexus6.zip to root for the very first time as well?
GMoGoody said:
Can you do this as opposed to using the CF-Auto-Root-shamu-shamu-nexus6.zip to root for the very first time as well?
Click to expand...
Click to collapse
You bet. You can be sure to have the most recent SuperSU that way as well. CF-Auto isn't always updated as quickly.
http://download.chainfire.eu/supersu
livinginkaos said:
You bet. You can be sure to have the most recent SuperSU that way as well. CF-Auto isn't always updated as quickly.
http://download.chainfire.eu/supersu
Click to expand...
Click to collapse
That su 2.4zip is for all devices? Not just for the n7 fhd? Thx
Via my NeXus™ 7FHD on XDA Premium app