[Q] Help, phone stuck booting?! - Galaxy S I9000 Q&A, Help & Troubleshooting

I flashed darky's rom with the voodoo lag fix and then stupidly tried to flash over the top my recovery file. now its stuck loading. can't access recovery mode but can access download mode... any ideas?

Just posted this in another thread, with similar issues, try this, should fix it.
--------------------------------
HI,
Try the following, worked for me
1) Go into recovery mode and wipe both cache and partition data
2) go to samfirmware.com and download the original rom for your phone (the one that came with it)... since you don't say what region you're from, I'll give you an example with mine. Mine is from Bell, and factory comes with UGJH2, so i downloaded that with ODIN and the PIT FILE, make sure to extract the TAR file from inside the RAR file. Put all 3 files in the same folder
3) Enter download mode, when the phone is in that state sometimes it's hard to access download, best way is... remove the battery, put it back in, then hold VOL DN + HOME + POWER until you see a working android bot inside a triangle. When you see that, connect your phone to your PC, double click on ODIN, then load the PIT file (CHECK BOX RE-PARTITION leave the others to default) and Select PDA and find the TAR file you extracted in STEP 2... then click on START, it's gonna take a few mins, and even after it's done, it's going to reboot, and it'll stay at the "S" logo for a bit, leave it, then it'll boot.
At least we hope it will.
Keep us posted,
Thank you,
Rodi.
------------------------------------

Can't get into recovery mode only download mode?! I'm on orange uk custom galaxy S Rom 2.1 originally. shall i just follow your steps but use a stock samsung android firmware?
Thanks Alot btw!

Yeah keep going with the download mode, it's very possible that the recovery mode process is not even necessary, but since I have no way of testing, it's doesn't hurt to try.
so get the orig rom, with pit associated with its (u'll see in on sam firmware which pit you need, most likely 512 for stock out of the box).
Keep us posted
Rodi

Fixed!!! flashed the new 2.2.1 firmware as well. is flying thanks for the help

alcurtis93 said:
Fixed!!! flashed the new 2.2.1 firmware as well. is flying thanks for the help
Click to expand...
Click to collapse
i have the same problem as u ..which 2.2.1 firmware did u flash and where to download ?
Cris

Dont worry mate easier to fix than I thought. Go to samfirmwares and go to firmware section and galaxy s and its called I9000 jpu. If you need any more help dont be afraid to ask
Sent from my GT-I9000 using XDA App

Heres the link.... http://www.multiupload.com/PUSOOBQ8K5
Password is samfirmware.com
Sent from my GT-I9000 using XDA App

alcurtis93 said:
Heres the link.... http://www.multiupload.com/PUSOOBQ8K5
Password is samfirmware.com
Sent from my GT-I9000 using XDA App
Click to expand...
Click to collapse
Thanks so u much

Related

Galaxy s not booting....

Evening friends i need your help lol
Right this is what happened, i made a backup of my rom then flashed cynogen mod and after a little play i didnt like it so i went to do a restore and now my phone hangs on the galaxy s screen?
I cant even get into recovery (vol up/home/power as the screen flashes at the galaxy s boot n dont do anything???
please help
Is download mode working (volume down+power+home)?
Sent from my GT-I9000 using XDA Premium App
Hi.
I am new to all this but yes download mode does work.
Im gutted and really want my phone back lol
I have just put the usb in my phone and there is a little circle icon in the middle of the screen ? (the phone is off btw) ?????
chrisvr4 said:
I have just put the usb in my phone and there is a little circle icon in the middle of the screen ? (the phone is off btw) ?????
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=991792
download and reflesh your phone , there is tutorial also
Download stock gingerbread or darky rescue center. Open odin and put all files in right place and tick repartition. Now put your phone in download mode, connect it to pc and when odin recognize it just click start.
Wait for it to boot l.
Thats all
Sent from my GT-I9000 using XDA Premium App
thanks for the replies guys but can you give me links for the stuff i need to get it sorted please.
chris.
Edit: before it all went wrong i was running stock rom 2.2.1 i believe not gingerbread as kies said no update for my device. Can i go back to stock ?
chrisvr4 said:
thanks for the replies guys but can you give me links for the stuff i need to get it sorted please.
chris.
Edit: before it all went wrong i was running stock rom 2.2.1 i believe not gingerbread as kies said no update for my device. Can i go back to stock ?
Click to expand...
Click to collapse
download this (latest GB release) :
http://dl.dropbox.com/u/19506141/GT_I9000_XWJVH_XXJVO_NEEJV3_Sbl.exe
extract files (.EXE) and put the files in right place in odin.
check repartition, put phone in dowload mode and then connect with odin.
you can root your phone with :
http://dl.dropbox.com/u/19506141/Gingerbread-GT-I9000-XWJVH-stock-kernel+hacks.tar
After your phone reboots, put in download again and put the file you just dowloaded in PDA (make sure repartition is NOT checked !!)
also odin 1.3 / 1.7 and samsung drivers for PC....
http://dl.dropbox.com/u/19506141/flash en drivers/Odin_+_pit.exe
http://dl.dropbox.com/u/19506141/flash en drivers/SAMSUNG_USB_Driver_for_Mobile_Phones.exe
idiot's guide
MeBeSad said:
http://forum.xda-developers.com/showthread.php?t=991792
download and reflesh your phone , there is tutorial also
Click to expand...
Click to collapse
It's 4.20 am... I am stupid; very stupid & I am panicing about my phone and this has worked..... thank the deity/s of your choice!!!
Guys much appreciate your help
I have got kies installed and the drivers would be already there yeah? or do i delete kies and install the usb drivers posted above ?
And the gingerbread i dloaded where in odin do i put the files after extracted and what about the pit files in odin? Sorry for all the Q's but im new to all this.
Right managed to put the files in odin v1.7 but what pit files do i use as there is 3 of them?
512 pit file
Sent from my GT-I9000 using XDA Premium App
phew!! a reply at last thank you!
in odin is there anything else to be ticked? phone bootloader update, phone EFS clear? or just tick th repartion?
cheers
You must tick 4 of them. Two should be ticked when you open odin. Other two that you should tick are repartition and phone bootloader update
Sent from my GT-I9000 using XDA Premium App
chrisvr4 said:
Guys much appreciate your help
I have got kies installed and the drivers would be already there yeah? or do i delete kies and install the usb drivers posted above ?
And the gingerbread i dloaded where in odin do i put the files after extracted and what about the pit files in odin? Sorry for all the Q's but im new to all this.
Click to expand...
Click to collapse
if i where you i'd delete everything from kies....
then install usb drivers....
extraxt GB .exe file.
youll get 3 files : PDA / PHONE / CSC
put them in odin : PDA--PDA / PHONE--PHONE / CSC--CSC
get pit512 file from odin .EXE
check repartition.
phone in download and connect to odin, and pres start
themate1987 said:
You must tick 4 of them. Two should be ticked when you open odin. Other two that you should tick are repartition and phone bootloader update
Sent from my GT-I9000 using XDA Premium App
Click to expand...
Click to collapse
when i open odin the 2 boxes that are ticked are AUTO-REBOOT F.RESET TIME and the unticked boxes are DUMP, PHONE EFS CLEAR, PHONE BOOTLOADER UPDATE, RE PARTITION so i tick all those yeah ?
I am not on my pc so i cant answer
Sent from my GT-I9000 using XDA Premium App
chrisvr4 said:
when i open odin the 2 boxes that are ticked are AUTO-REBOOT F.RESET TIME and the unticked boxes are DUMP, PHONE EFS CLEAR, PHONE BOOTLOADER UPDATE, RE PARTITION so i tick all those yeah ?
Click to expand...
Click to collapse
leave all checks as they are, do not check EFS clear or bootloader box or dump.
the only box you have to check is repartition
Got you right going to see if i can bring it back to life now.
Will post up my result.
Thanks very much guys
chrisvr4 said:
Got you right going to see if i can bring it back to life now.
Will post up my result.
Thanks very much guys
Click to expand...
Click to collapse
your welcome, if you have problems report here and i will help you.
im home till 14:30

UK Galaxy S Help please?

Basically, in all of my wonderful wisdom, decided to try and root my Galaxy S thinking it would be a similar process as to that of the HTC Desire on the ground that I was sick of the way Orange have changed the phone.
Several methods here didn't work so I decided to play about with Odin. I ended up in a boot loop and have now managed to install a US T-moblie OS for a Vibrant handset. Does anyone have any idea how to rectify this horrific balls up? Or where I can get a UK OS from to put back on it? Also I have failed to root the phone.
now seems to be good time to install gb with cfroot kenrel
I know I'm a complete novice and I'm sorry for that, but could you/show or link me to a tutorial of that at all please?
Dave Dave Dave Dave Dave. What have you done?
Don't worry mate, check out the ezbase thread in development section. Full instructions and downloads included. Should sort you right out.
Happy flashing.
Sent from my GT-I9000 using XDA Premium App
So far so good, just lacking the room as I have no idea what I should download.
Any idea?
Dave759 said:
So far so good, just lacking the room as I have no idea what I should download.
Any idea?
Click to expand...
Click to collapse
Probably best to go for rom kitchen jvh - stable, customisable and great help from the users in the thread. Once you've a bit more experience with sgs flashing, then insanity all the way.
Hope it all goes well mate.
Edit: dave, have you flashed the gingerbread base rom from the ezbase thread yet?
Sent from my GT-I9000 using XDA Premium App
I couldn't tell you where I'm at. All I've done is follow the steps, downloaded EZOdin V1.70 and this;
Repartition is not mandatory, but it does not hurt to repartition the phone.
Start Phone in Download Mode (No Cable Attached)
Open EZOdin.
- Check Re-Partition
- Select EZbase.pit as PIT
- Select EZbase-PDA-XWJS3.tar.md5 as PDA
- Select EZbase-PHONE-XXJVE.tar.md5 as PHONE
- Select EZbase-CSC-XXJV1.tar.md5 as CSC
checked everything it says and pressed start. The message box is up to;
<ID:0/007> Set PIT file..
<ID:0/007> DO NOT TURN OFF TARGET!!
and has been that way for a good 10 minutes.
this is very strange,anyway
1- did u install kies as its important for the sake of the drivers
2- did u check/tick the 3 boxes in odin
3- if the 2 above are checked try changing the usb port or the computer
keep me informed m8
I think that's the froyo 2.2.1 ezbase base. On the first page, there should be a jvb (I think) ezbase download.
10 minutes is too long, pull battery, disconnect usb, close ezodin, reopen, re-add files, go to dl mode on phone, connect usb, wait for yellow light in ezodin, press start.
Sent from my GT-I9000 using XDA Premium App
Dave, if you want to pm me your home number, i can call you to talk you through it.
Worst case scenario is a flash of eclair jm9 - will sort 99% of snags.
Sent from my GT-I9000 using XDA Premium App
Do you have 3 button combo?
If so...
Download STOCK JVH gingerbread with bootloaders.
Follow instructions on JVH thread in the first post.
I would go into recovery, factory reset and format internal sd card before flashing.
Use 512.pit and repartition and use odin.
http://forum.xda-developers.com/showthread.php?t=1011901
Download this...
http://www.multiupload.com/INQRN37ODA
You can get odin and 512 pit from samfirmware.com
Then when you have a working phone you can root with cf-root.
http://forum.xda-developers.com/showthread.php?t=788108
And maybe install the screen off animation with battery percentage...
http://forum.xda-developers.com/showthread.php?t=1055979
This is the link to $omator's file for JVH...
http://forum.xda-developers.com/attachment.php?attachmentid=591847&d=1305015870
In my opinion, just get a stock JVH ROM from Ramad
Get it here
Run the .exe and the 3 files will be unpacked.
Try using Odin 1.3 to flash. I had problems with the phone not booting when I used 1.7
I'm using a 513 Pit so that's what I recommend. 513 was made a day after 512 so it makes me think it may correct some problems as no one knows the full theory behind Partition Information Tables (PIT) files.
When the phone boots for the first time, go into the phone dialler and put in the code below to factory reset the phone. This seems to cure issues that may occur if you just start using the phone as normal.
*2767*3855#
Good luck and post back if you have problems.
goodluck dave

ics

Hello im new in this forum and i just want to know if possible if there is any ics rom for I9000 to upgrade whith odin or heimdall since im not able to get the recovery menu in my galaxy
Is there a reason you cannot root your phone and install cwm?....full guide and download links to the files needed here : http://www.theandroidsoul.com/how-to-root-xwjvb-and-install-clockwork-mod-cwm-recovery/
I have tried that already i think its hard briked cod if i turn im off i cant turn im on anymore only if i flash him again
Sent from my GT-I9000 using XDA App
you may have better luck finding stock files to flash through odin, your going to want the 512 pit file and I9000UGJL2Complete (thats your PDA file) and make sure you check the re-partition box!!! let its reboot and it should be like purchasing from day one.
Put it into download mode again and then put speedmod-kernel-k13e-500hz (PDA file) in the PDA box, and only have that file present, with re-partition UNCHECKED this time. let run and when it reboots it should still work (cause its running froyo 2.2) and be the same
however now you should be able to boot into CWM recovery to flash custom rom. if you want, before flashing the speedmod kernel you can run superuser1click to install superuser.
Hope that helps!!
Ok i will try that but im not sure if it will work cos even in download mode i only have a black screen and the two lights from the soft keys
Sent from my GT-I9000 using XDA App
i found a thread discussion about similiar problem and hope there is any help to your case.
http://forum.xda-developers.com/showthread.php?t=1120880
Just read it trough and try everything out because at what point you are at there is nothing more you can do

Bricked Galaxy TAB 8.9 (GT-7300) - $20 reward for working solution

Hi,
So, I got a Samsung Galaxy TAB 8.9 (GT-7300) WiFi+3G. Nordic/European version. I have a long history of rooting and running custom ROM's on my Android devices, but this time i f##ed up a bit.
1. Installed root_original.zip from this thread by copying it on to the tablet and applying it from stock recovery.
2. Booted and installed Superuser and ROM Manager from Market.
3. Used ROM Manager to install CWM for Galaxy Tab 10.1 (Yes, I know...).
4. Tab would not boot, but I could still get in to download mode. Browsed some XDA threads and came across this guy who seemed to have the same problem. I did not see that he had a P7310 (WiFi only) tablet. So, I used Odin 1.85 to install the bootloader, which was for the P7310, not for P-7300. Now, the tablet boots but the display is just flickering, like it is using a wrong refresh rate or wrong resolution. Not at all possible to read anything, but I can still get into Download mode.
5. Installed stock rom from here, specifically this one: P7300XWLA2------2012 January----P7300NEELA1-----Nordic countries----
Still no luck. The tablet boots into Android but the display is still flickering.
$20 for anyone who gets me out of this mess
Can you come in recovery ?
Than try this?
http://forum.xda-developers.com/showthread.php?t=1519564
There is an option in CWM under the mount and storage tab where stands mount usb connection click on that and move this to your tab after that install it
I hope it will work!
You could also try the Swedish firmware: http://hotfile.com/dl/146666862/13403b2/P7300XWKL4_P7300NSEKL1_NSE.zip.html
The NSE are usually pretty much the same as NEE with some swedish bloatware. Worth a try I guess.
Also see this guide for how to use Odin in case you did something wrong: http://forum.xda-developers.com/showthread.php?t=1406137
One thing that I've noticed when flashing with Odin is that even if I check the F.reset checkbox it still does not do a factory reset (at least it did not do it for me). You should be able to do a factory reset using the stock recovery.
Oh and btw, my advice is for free.
Hi safariking,
I can get in to recovery, but I'm unable to read anything, as the display is just flickering. I would need a press-by-press guide in order to perform the steps correctly... :/
Thanks kallt_kaffe, I'll try the swedish firmware and follow the guide step-by-step
kallt_kaffe said:
You could also try the Swedish firmware: http://hotfile.com/dl/146666862/13403b2/P7300XWKL4_P7300NSEKL1_NSE.zip.html
The NSE are usually pretty much the same as NEE with some swedish bloatware. Worth a try I guess.
Click to expand...
Click to collapse
Installs correctly but does not fix my display problem.
kallt_kaffe said:
Also see this guide for how to use Odin in case you did something wrong: http://forum.xda-developers.com/showthread.php?t=1406137
Click to expand...
Click to collapse
I followed the guide step-by-step. No errors occured during flashing.
kallt_kaffe said:
One thing that I've noticed when flashing with Odin is that even if I check the F.reset checkbox it still does not do a factory reset (at least it did not do it for me). You should be able to do a factory reset using the stock recovery.
Click to expand...
Click to collapse
I can't really verify the factory reset. I can get into stock recovery, but the display is still rubbish so I can't do a manual factory reset.
kallt_kaffe said:
Oh and btw, my advice is for free.
Click to expand...
Click to collapse
I voted for you guys in ESC so I guess we're even
I have attached a photo of the tab in stock recovery so you can see what's wrong. This happens no matter if I start normally, recovery or download mode.
snubbel said:
Installs correctly but does not fix my display problem.
I followed the guide step-by-step. No errors occured during flashing.
I can't really verify the factory reset. I can get into stock recovery, but the display is still rubbish so I can't do a manual factory reset.
I voted for you guys in ESC so I guess we're even
I have attached a photo of the tab in stock recovery so you can see what's wrong. This happens no matter if I start normally, recovery or download mode.
Click to expand...
Click to collapse
Wooow that looks not good man i think you must return it back to samsung
you can run a logcat maybe
snubbel said:
I have attached a photo of the tab in stock recovery so you can see what's wrong. This happens no matter if I start normally, recovery or download mode.
Click to expand...
Click to collapse
If you turn it off and charge it, is the charging-mode-display also distorted?
Also if I were you I would leave it on in download or recovery mode and let the battery drain completely. Worth a shot I guess.
Questions or Problems Should Not Be Posted in the Development Forum
Please Post in the Correct Forums & Read the Forum Rules
Moving to General
kallt_kaffe said:
If you turn it off and charge it, is the charging-mode-display also distorted?
Click to expand...
Click to collapse
If I turn it off it automatically turns back on and boots Android. So I can't see if the "charging while turned off" icon is also distorted.
kallt_kaffe said:
Also if I were you I would leave it on in download or recovery mode and let the battery drain completely. Worth a shot I guess.
Click to expand...
Click to collapse
I left it in download mode last night, it's still turned on. I'll let the battery drain and see what happens when I connect the charger.
When I flash a complete ROM with Odin (e.g. the Swedish ROM you suggested) - is there anything left to flash that could be causing this? If I were to return the tablet to the dealer, will there be any evidence of dumb-user-flashing?
snubbel said:
When I flash a complete ROM with Odin (e.g. the Swedish ROM you suggested) - is there anything left to flash that could be causing this? If I were to return the tablet to the dealer, will there be any evidence of dumb-user-flashing?
Click to expand...
Click to collapse
I honestly do not know.
Have you tried flashing the PIT file (in the PIT section) along with the ODIN image (in the PDA section)? You can download the PIT file so you can click on Repartition, right here. It's a very small file. Be sure you have F.Reset Time checkmarked too. Best of lucks.
If you flash a bootloader for P7310 so when you trying to flash P7300 ROM with odin, the bootloader will mapping all file just like P7310 with their partition Layout.. I think the pit file is not the solution..
First you need turn back the bootloader to original form.. I dont know where I can find P7300 bootloader..
After you finish with the bootloader, try to install P7300 Stock rom, with pit file and repartition..
I dont know if this post will help you.. but it worth to try..
EDIT:
maybe you can use firmware from P7300ZSKH5 from this link
This file include with bootloader and pit file..
Flash with Odin like image below
Sorry for my english..
nirogu325 said:
Have you tried flashing the PIT file (in the PIT section) along with the ODIN image (in the PDA section)? You can download the PIT file so you can click on Repartition, right here. It's a very small file. Be sure you have F.Reset Time checkmarked too. Best of lucks.
Click to expand...
Click to collapse
Re-partitioning with the PIT file along with the ROM did not help :/
suwandiapr said:
If you flash a bootloader for P7310 so when you trying to flash P7300 ROM with odin, the bootloader will mapping all file just like P7310 with their partition Layout.. I think the pit file is not the solution..
First you need turn back the bootloader to original form.. I dont know where I can find P7300 bootloader..
After you finish with the bootloader, try to install P7300 Stock rom, with pit file and repartition..
I dont know if this post will help you.. but it worth to try..
EDIT:
maybe you can use firmware from P7300ZSKH5 from this link
This file include with bootloader and pit file..
Flash with Odin like image below
Sorry for my english..
Click to expand...
Click to collapse
Thanks for your suggestion, but unfortunately: no luck.
Just to be sure this isn't a compatibility issue on my computer, I set up a clean install Win7. I'm using x64, could this be an issue?
snubbel said:
Thanks for your suggestion, but unfortunately: no luck.
Just to be sure this isn't a compatibility issue on my computer, I set up a clean install Win7. I'm using x64, could this be an issue?
Click to expand...
Click to collapse
As long as you have the right drivers installed, no. That's my setup.
I had a similar issue. It occured only when I turned display off and on, both in android and in battery charging mode while powered off. I just went back to the store and got it replaced. xD
Anyway the flickering began to show up after flashing 3.2 back from a 4.0 rom... So I think there was something wrong with the bootloader.. Didnt find any tar file containing the original bootloader.. Perhaps someone here can make it for you
hey,
i got same problem after i tried to install cm9. now i cant install nothing (i formated cash, data, system and preload) no data factory reset working. i have nonstop bootloops and format cache and dalvik not working but cwm ist starting but not working really. but can start download mode too ... so i think its not a super-brick for my gt 7300 from switzerland.
so, i will try to download from samMobile the original firmware and to flash with odin. anybody knows a tutorial with odin for gt 7300? cant find nothing for pit, csc, tar ...
please help me
thx sophie from switzerland
suwandiapr said:
If you flash a bootloader for P7310 so when you trying to flash P7300 ROM with odin, the bootloader will mapping all file just like P7310 with their partition Layout.. I think the pit file is not the solution..
First you need turn back the bootloader to original form.. I dont know where I can find P7300 bootloader..
After you finish with the bootloader, try to install P7300 Stock rom, with pit file and repartition..
I dont know if this post will help you.. but it worth to try..
EDIT:
maybe you can use firmware from P7300ZSKH5 from this link
This file include with bootloader and pit file..
Flash with Odin like image below
Sorry for my english..
Click to expand...
Click to collapse
I have to say, I was about to send the tablet to samsung, it was dead, no rom, no boot, no partition, no USB connection to store, what save me was the Odin up load that you recommended me, the tablet was really crashed.
I Think that is a sollution for actually almost any problem on the tablet (a complete format, sure, but still a good solution for ROM problems).
anyway, Many Thanks!!!!!!
Newbie try to help.
Have you try to install another CMW version using odin? Maybe it's caused by wrong CMW version. Try CMW v5.5.0.4 here http://forum.xda-developers.com/showthread.php?t=1312218

[Q] Updated ROM Philz JB 4.1.2 XXLT6 via Odin but won't go past samsung gt-n7000

Hope you guys can help me.
Was updating my ICS (Criskelorom) to JB 4.1.2 XXLT6 ROM of Philz (PhilZ-cwm6-XXLT6-XSA-5.06.1.tar.md5) via Odin 3.07. Initially had some issues but, managed to get to where Odin resulted in a PASS. On REBOOT I only get up to the Samsung Galaxy GT-N7000 screen with a yellow ! triangle at the bottom. I was able to get to both Recovery and Download modes but would never get passed to homescreen and just stay on black screen.
Did it several times and got worried I'd brick my phone so I ran the ICS zip I had stored on my SD via Recovery mode and was able to get my phone running. Still want to pursue my JB upgrade though but, not sure if I was doing it right. Any help would be much appreciated guys.
Here is what I did...
MADE SURE OF THE FF.:
1) Install USB driver for Samsung Galaxy Note to transfer files between the phone and the computer using download of KIES from Samsung site
2) Enable USB Debugging Mode on the phone to connect the Android device with the computer
3) created a back-up of my contacts only
4) charged to above 80% battery charge
5) The phone should be factory unlocked and not locked to any particular carrier - I had unlocked it during my ICS upgrade from the GB original OS
THEN FOLLOWED THE STEPS:
Step-1: Download PhilZ-cwm6-XXLT6-XSA-5.06.1.tar.md5 for Samsung Galaxy Note to the computer
Step-2: Download Odin 3.07 which will help to install the root package on the phone. Extract the Odin zip to get Odin3 v3.07.exe file with some other files
Step-3: Place the Galaxy Note into Download Mode by pressing and holding Volume Down, Home and Power buttons together until a construction Android robot appears on the phone's screen. Now press the Volume Up button to continue to enter into Download Mode
Step-4: Run Odin3 v3.07.exe as an Administrator
Step-5: Connect the Note to the computer using USB cable while it is in the Download Mode. Wait for some time until Odin detects the phone. When the device is connected successfully, the ID: COM box in Odin will turn yellow with the COM port number. Also, the successful connection will be indicated by a message saying Added in Odin.
Note: If the Added message does not come then try another US port, try the one located at the back side of the computer. If Odin still fails to detect the device then re-install USB driver
Step-6: In Odin, click the PDA button and select the PhilZ-cwm6-XXLT6-XSA-5.06.1.tar.md5 file
Step-7: Now configure the Odin settings. Ensure that the Auto Reboot and F.Reset Time checkboxes are selected in Odin. As for the Re-Partition, uncheck the option
Step-8: Once everything is set, click the Start button in Odin. The installation should begin now and would take about few minutes to complete
Step-9: When the installation process is completed the phone will restart automatically. And soon a PASS message with green background will appear in the Odin indicating successful installation. After the home screen appears on the phone, unplug the USB cable from the device to disconnect it from the computer
Was able to reach Step-9 but my phone would not get to home screen.
Please help me with any advise anyone can give me?
thanks.
By the way, saw another option for Steps 5-6:
Step-5: Connect your Note N7000 with your PC using a data cable. Once the device is successfully connected, you will see a notification in Odin in the bottom left saying Added!! - if for some reason, you do not see the said notification, try another USB port. Also, check for ID:COM port being depicted by a number in yellow to make sure that you have successfully added your device.
Select the following files in Odin at their respective tabs from extracted XXLT6 firmware folder:
Step-6:
Click the PDA button to select the .tar file extracted earlier.
Click the Phone button, and select file with *modem* in its name (ignore, if this file does not file exist).
Next, click the CSC button, and select file with *csc* in its name (ignore, if this file does not file exist).
Click the PIT button to select the .pit file. (ignore, if this file does not file exist).
Ensure that Auto Reboot and F. Reset Time are the only options selected in Odin window. Also ensure to select Re-Partition checkbox only if you are using a .pit file.
Except since I only had the TAR file I ignored the rest so I assumed I was doing it right up to that point. Also, the YELLOW highlight in Odin 3.07, wasn't yellow but kind of light blue.
That was it. All I did. Still, not succesful.
Please help.
Thanks.
Phew! That's a lot to read.. The file you are trying to flash is just a kernel not a whole rom. That's why your phone after the flash has a JB kernel and ICS rom. That's why the phone does not boot. To upgrade to JB, download a stock rom from sammobile.com and flash it using Odin the same way just in PDA of Odin.
nokiamodeln91 said:
Phew! That's a lot to read.. The file you are trying to flash is just a kernel not a whole rom. That's why your phone after the flash has a JB kernel and ICS rom. That's why the phone does not boot. To upgrade to JB, download a stock rom from sammobile.com and flash it using Odin the same way just in PDA of Odin.
Click to expand...
Click to collapse
Sorry about the read. =)
Was thinking I'd rather be complete than have anyone helping need to ask more clarifications to help me. =D
Oh that's why. Thanks for the reply. I will do that.
So I need to get the WHOLE ROM from the site you mentioned. A ROM that is complete, Kernel and all. Actually I thought I did get a complete ROM. Did not realize it was just a Kernel. What would be the best way to determine if a ROM is complete? What is usually the size of the file itself? The one I downloaded was like 8MB so I thought that was pretty big. Kinda looked for awhile for that XXLT6 original JB ROM so didn't stop to think if it was just a Kernel. My bad.
By the way, are the ROMs on Sammobile rooted? Or do I need to root them?
thanks again!
izmoothski said:
Sorry about the read. =)
Was thinking I'd rather be complete than have anyone helping need to ask more clarifications to help me. =D
Oh that's why. Thanks for the reply. I will do that.
So I need to get the WHOLE ROM from the site you mentioned. A ROM that is complete, Kernel and all. Actually I thought I did get a complete ROM. Did not realize it was just a Kernel. What would be the best way to determine if a ROM is complete? What is usually the size of the file itself? The one I downloaded was like 8MB so I thought that was pretty big. Kinda looked for awhile for that XXLT6 original JB ROM so didn't stop to think if it was just a Kernel. My bad.
By the way, are the ROMs on Sammobile rooted? Or do I need to root them?
thanks again!
Click to expand...
Click to collapse
They are just stock roms, to root again use the philz kernel but for jb this time. Also use the .zip this time instead of tar file, you can flash the zip file from stock recovery itself. You can raed more in philz kernel thread
Sent from my GT-N7000 using Tapatalk
treacherous_hawk said:
They are just stock roms, to root again use the philz kernel but for jb this time. Also use the .zip this time instead of tar file, you can flash the zip file from stock recovery itself. You can raed more in philz kernel thread
Sent from my GT-N7000 using Tapatalk
Click to expand...
Click to collapse
Got it, thank you Sirs you've all been a very big help. I ran into some issues with TW right after completing the install of 4.1.2. Every darn thing was stopping even acore and TW. Was about to chicken out and go back to my safety ICS ROM when I got to read some stuff about needing to Clear/Reset on Recovery mode after any firmware flashing as well as Clearing the Cache so I did. And voila, it worked. I think I'll rest my worrying brain for now on the root. =P
I'll root it next week. I'll just have fun with it for now. Been up playing around with this for over 24hours now. Having too much fun but already drained.
Thank you again for you help!
same situation here...!!!
hello XDA ppl...
I had ICS 4.0.4 and attempted to use PhilZ-cwm6-XXLTA-ATL-5.15.0.tar.md5.
That took me to the same situation I think... kernel for JB and ICS ROM...
I power on my phone and it gets to a GT-N7000 Note + Yellow Triangle screen and NO MORE!
I can get to PhilZ Recovery Mode or ODIN Download Mode.
That´s all...
I will attempt right now what you told the creator of this thread and update if it helped.
any help is welcome...
FIXED!!!
AWESOME!!!
My bot is back again!!!
Thanks a lot guys...
This thread worked as a charm. :victory:
1. Odin 3.0.X
2. Factory Firmware
3. Flash it as PDA.
4. No yellow triangle.
5. Removed battery and waited 5 seconds.
6. recovery mode.
7. clear data/factory reset.
Done!
---------- Post added at 03:33 AM ---------- Previous post was at 03:28 AM ----------
juliowong said:
AWESOME!!!
My bot is back again!!!
Thanks a lot guys...
This thread worked as a charm. :victory:
1. Odin 3.0.X
2. Factory Firmware
3. Flash it as PDA.
4. No yellow triangle.
5. Removed battery and waited 5 seconds.
6. recovery mode.
7. clear data/factory reset.
Done!
Click to expand...
Click to collapse
Well... finally I am back to ICS.
Now gotta find a safe way to get it to JB.
juliowong said:
Now gotta find a safe way to get it to JB.
Click to expand...
Click to collapse
Safest way to get to JB with wipe (that is formatting) is to get philz kernel for ICS and then reboot to recovery do factory reset and wipe /system /data /internal storage /cache and then reboot to download mode and flash JB from odin. Else if you dont want to loose data, just boot into download mode and flash JB using odin.
juliowong said:
6. recovery mode.
7. clear data/factory reset.
Well... finally I am back to ICS.
Now gotta find a safe way to get it to JB.
Click to expand...
Click to collapse
Yeah!! May be you want to start by not wiping on a stock ICS kernel.

Categories

Resources