I tried installing the nexus s gb port on my captivate and now when I try to turn it on, the at&t world power screen comes up for less than a second, and then the phone turns off and about 30 seconds later, it comes back on and it stays like that until you pull the battery. I've tried everything, 3 button combo, plugging it in while odin is open while holding all 3 buttons and placing the battery in and releasing the power, opening adb, and nothing has worked. The same thing happens when I plug it in, except with the little loading thing that pops up before the battery charging animation. I don't know where I went wrong with this, but I just checked my devices on my computer and it said a nexus s was attached. I installed the nexus s drivers, and it now works with adb but I still can't get it into recovery. Can anyone help?
If you read the posts about Gingerbread/Cyanogen "tech demos" the first thing it said is you cannot restore using the 3-button combo you should not install. This is mainly for folks with a Build 1008 Phone.
You cannot use ADB Commands to get back into download.
Hopefully this will work for you though:
Pull your Sim Card, Battery, and any External SDCard
Turn on Odin
Plug your Phone back into the USB Cable (battery out still)
While holding down the Volume +/- Button - put your battery back in.
It should go into DOWNLOAD MODE.
If you get the Gray Battery Charge screen - it didnt work. Rinse and Repeat until it goes into the DOWNLOAD MODE. Might take a few tries.
Related
I was doing an Odin One Click restore to return to stock
Odin got stuck for some reason. I waited nearly 45 minutes before pulling the battery and attempting to start over.
Upon pulling the battery, the phone went off, as expected. removed Sim, SD card, replaced battery, replaced battery cover, etc etc.
The phone is 100% unresponsive.
1: Removing and replacing battery - no effect
2: VolUp + VolDn + Power - no effect
3: Plugging into any one of the 5 USB ports on the computer - no effect
4: Plugging directly into the wall - no effect
Nothing I've tried or read has given any solution to even get the phone to come on.
Last ditch effort, going to leave the battery out for an hour or so, and failing that, going to leave everything plugged in for an hour or so.
The battery on the phone had nearly 95% when I started this endeavor.
Does anyone have any hints or suggestions as to other things to try?
Thanks.
I had that happen last night. Got stuck sending "factory.rfs" or something like that.
Anyway, plug your phone to the wall for a few minutes. Maybe an hour. Then open Odin, hold Vol-UP and Vol-DOWN (dont push power), and plug the device to the computer. It should boot to Download mode.
Now, I used the version of Odin that allows you to select the firmware -- there's another that comes with JF6 preloaded. I installed JH3. Also, when I selected the firmware with the "Phone" section and flashed, it did not work (FAIL). Later I tried the "PDA" section and it did.
Let me know how that goes.
EDIT: Plugging to the wall, the screen will not turn on. But the back will get warmer. Trust me, it is charging. My battery was full after the flash.
del
Thanks for the quick response.
I figured at this point, I couldn't do anymore harm that good. Worst case, I buy a new one.
So, I started tinkering with various key combination... Lo and behold, one particular set gave me the infamous "orange dump".
From there, and a bit of searching (i had remembered seeing the bit about the orange hex dump somewhere), I found the same solution you just provided.
Worked, phone is stock and functional.
Kudos.
Dave
i too was trying to install vodoo and after installing it my phone wont turn on it just keep on flashing atnt screen and next screen i see is samsung and thts keep on repeating no luck my phone wont turn on please help me am badly stuck.
thaank you.
IF you are able to get your phone to the point of seeing the att screen then you should be able to hold down the vol up+down buttons while also holding the power button...Just to be safe, hold it till the att screen flashes twice. Then release and you should be taken to the recovery mode. If not, Try the same steps again plugging in the usb while the att screen is present. Repeat as necessary. Good luck.
Yesterday, I was flashing back to the JH6 again. It stuck at factory.rfs for a long time. Then, I tried to restart. After phone is off, it couldn't turn on any more. No matter, press vol down + power or press vol up and down then plug in usb with ODIN on. Or just press power button. I've tried the whole day even try to put on wall charger overnight. There is no battery screen during charge just for the reference.
It seems there is no way to bring it back other than jtag? anyone has any experience about this dead phone and bring it back to life?
Thanks.
Have you tried another battery? Just to make sure it didn't take a dump. It has been reported by very few that has happened.
Same thing happened to me it froze during the Factory.rfs so I turned it off and the phone wouldn't turn back on. I panicked and found somewhere else on these forums although I cannot find the thread again. What I did I just plugged my phone into the wall charger for a couple minutes with the battery. Then I unplugged it and took the battery out for a another minute then put the battery in and try to turn it on while holding the volume - or + I forgot, and if you start to see Orange Text being dumped to your screen chances are you can force it back into Download Mode. Just keep trying different button combos to get it working, unless I was extremely lucky but I do not think these phones can be bricked so easily.
Thanks. I did see the thread you mentioned and tried every way I can but not available. Fortunately, I got ATT warranty center to send me a replacement. However, the only catch is that I'm not sure if it's unlockable now since it might come with JH7. If that's the case, I'm gonna sell it and get other phone.
samsung captivate brick
i have the same problem... im running windows 7 x64(64 bit) and i was updating my phone to the rooted 2.2 froyo update via odin with the "I897UCJI6-OCD-REV02-Low-designgears" while updating the phone when the odin program froze and ruined/bricked my phone... i have tried all the steps to try and un-brick my phone but at this point im about ready to give up.... at this point my phone will not power on in any mode nor will it go into recovery mode or download mode... if any one has any info on how to fix this please let me know....
Hey guys, here's what's wrong.
I was running the latest version of MIUI and found it to be annoyingly buggy, so I installed Cyanogen from ClockworkMod and start installing it. It ended up hanging halfway through and wouldn't progress. I made what was probably a dumb decision and decided to turn it off since it seemed to have frozen.
Now...it won't turn on. If I connect a wall charger or USB cable, the symbol of an empty battery with the white loading circle comes up for about five seconds, but the circle is not rotating and the screen goes black. This repeats nonstop.
Holding down vol down + home + power to get it into Download mode fails, it just says LOW BATTERY CAN'T DOWNLOAD in red letters. Doing the same with the volume button up gets nothing. I've tried leaving it to charge for two days with no results.
I bought a USB jig and tried using it (removing battery and SIM card, putting battery back in, plugging jig in) but it does nothing. I've tried several times.
Any advice? Is it just dead?
try an external charger to charge your battery or borrow someones battery to test your phone. failing that, charge your battery in someone else's phone.
Was the battery full when you tried installing cyanogen mod, and did you follow the instructions fully?
Clean the battery contacts on both the battery and phone pins. Use another charger, and check the port for blockages/dirt (blow in it).
Try another battery..
-Leave the jig in for 30 mins.
-Hold the combo and then put the battery in whilst holding the combo.
-Plug into your computer (with battery) and try the combo. Then try without, and put battery in whilst connected and whilst holding.
-Hold combo then plug into computer
Some of the methods above may require some extreme skill or a helping hand
It could be water damage.
I don't think it is bricked as i don't think those messages would be showing up, but i could be wrong.
If none of that works and no-one else comes up with any other ideas then you may have to use the unbrickable mod. Search for it, it's a hardware hack..
Good luck
Hello all,
I searched around, but didn't find anything quite like my issue so figured I'd create a new thread.
I work for a company that uses Galaxy Tabs for various purposes. One of our men brought back their VZW Galaxy Tab (SCH-i800) and it was in an infinite boot loop.
I went to recovery and attempted to do a full wipe. This did not work (partitions were all jacked up) so I couldn't get it fixed. I'm not sure if the guy tried to root the thing and broke it or what.
Anyway, I was attempting to root then fix the partitions (then was going to flash a stock unrooted rom) and ended up soft bricking it (Phone Icon -- /!\ -- Computer Icon). The issue I'm having is the only time that screen comes up is when the device is plugged into the wall. It turns on, then off, then on, then off. If I unplug the device, it shuts down with no way of bringing it back up. I've tried holding power for 5 minutes, the same amount of time with power + vol up and power + vol down. Plugging it into the computer's USB ports does not help either.
It's like the battery is drained but it won't charge when it's on the soft brick screen. I've had it plugged in to the wall for almost 6 hours now with no hope in sight. When it's plugged in, I feel heat on the back of the device like it would normally be charging. The AC adapter is also the standard warmth after a lengthy charge.
I was wondering if anybody has had similar issues with this device and if there is any way to correct it.
--- EDIT 8/10/2012 ---
Another thing of note is when the device is charging, I can power it down by holding power for a few seconds, but the Soft Brick screen pops back up almost immediately upon release of the button.
I cannot boot into recovery or the standard download mode even when it's plugged in.
As long as you can get the Phone ! PC screen, your'e good, because this screen IS as a download screen. Go to this screen and flash a known good ROM.
ableeker said:
As long as you can get the Phone ! PC screen, your'e good, because this screen IS as a download screen. Go to this screen and flash a known good ROM.
Click to expand...
Click to collapse
You must not have read the whole thing. Not a problem.
The only time I get the Phone ! PC screen is when it's plugged in to the wall. As soon as I unplug it, it goes away and the device won't start up no matter what I try.
When you connect the tab to the pc, is it recognized by Odin.
Sent from my GT-P1000
salahmed said:
When you connect the tab to the pc, is it recognized by Odin.
Sent from my GT-P1000
Click to expand...
Click to collapse
No... When the device is unplugged from the wall it is shut down and won't boot back to the download screen, recovery, nothing. It doesn't turn on. There are occasions where the download screen stays up but it appears to just be frozen. The computer doesn't recognize it and neither does Odin.
I left it plugged in when I left work on Friday... Going to see if charging for the weekend does anything.
MaskedDriver said:
No... When the device is unplugged from the wall it is shut down and won't boot back to the download screen, recovery, nothing. It doesn't turn on. There are occasions where the download screen stays up but it appears to just be frozen. The computer doesn't recognize it and neither does Odin.
I left it plugged in when I left work on Friday... Going to see if charging for the weekend does anything.
Click to expand...
Click to collapse
No dice.. still jacked.
I determined the following scenarios may have happened:
1) The battery died (bad battery) during a software update and messed up the partitions
2) The battery died (bad battery) while he attempted to (unauthorized) root or flash the device, messing up the partitions.
The only thing I'm sure of is the battery is fried so any kind of hacking I can do to the device are for naught. I was able to get it to connect to Odin this morning for about 3 minutes (after having it plugged in to the wall all weekend). During the flash it shut down again bricking it even worse. Now the device won't turn on when plugged in to the wall.
Thanks for the suggestions and help. I'm calling this a lost cause at this point. We're just swapping out the device for a new one. Once that's complete, I may tear the device down and try to do a reset on the main board to see if that does anything, though I doubt that's the case.
Right I had exactly the same problem as you (exactly the same symptoms) but I have now fixed my tablet.
Like you I got to the point where the Tablet had enough charge to actually unplug it and connect it to my PC where I then tried to flash a stock ROM using Odin. About three quarters of the way through flashing the stock ROM the tablet died, disconnected from Odin and I got a message in the task list in Odin advising me that the process had failed. Even weirder my PC did an emergency shut down and restarted in safe mode.
Anyway I tried it again but when I started my machine, once I'd logged onto my desktop I started up Odin as quickly as possibly, selected the .tar file and pressed start as quickly as possible....it worked and my tablet was flashed with a stock ROM. However my battery was still pretty much dead and the first time of charging once it had been flashed with the ROM took about 24hrs plugged in at a mains charger for the battery to reach 100%.
My point is persevere with it and you will fix it. I was at the point where I was about to send it off to be un-bricked but obviously I'm glad I didn't now.
It is a ***** of a brick though, this 'coma brick'.
I've been having these same issue with my friends i800 galaxy tab. Can you chime in and offer some advice?
Sent from my Galaxy Nexus using Tapatalk 2
same problem-solved
I was having the exact same issue. the device screen was completely black when plugged into the computer. I was just about to give up when, all of a sudden the device went to the boot error screen while plugged into my computer. Apparently, it must remain plugged into the computer for about 20-30 minutes. Once this screen appeared, I ran the Heimdall one-click unbrick utility, and like magic, my galaxy tab was working again. Give it a try, and good luck.
MaskedDriver said:
Hello all,
I searched around, but didn't find anything quite like my issue so figured I'd create a new thread.
I work for a company that uses Galaxy Tabs for various purposes. One of our men brought back their VZW Galaxy Tab (SCH-i800) and it was in an infinite boot loop.
I went to recovery and attempted to do a full wipe. This did not work (partitions were all jacked up) so I couldn't get it fixed. I'm not sure if the guy tried to root the thing and broke it or what.
Anyway, I was attempting to root then fix the partitions (then was going to flash a stock unrooted rom) and ended up soft bricking it (Phone Icon -- /!\ -- Computer Icon). The issue I'm having is the only time that screen comes up is when the device is plugged into the wall. It turns on, then off, then on, then off. If I unplug the device, it shuts down with no way of bringing it back up. I've tried holding power for 5 minutes, the same amount of time with power + vol up and power + vol down. Plugging it into the computer's USB ports does not help either.
It's like the battery is drained but it won't charge when it's on the soft brick screen. I've had it plugged in to the wall for almost 6 hours now with no hope in sight. When it's plugged in, I feel heat on the back of the device like it would normally be charging. The AC adapter is also the standard warmth after a lengthy charge.
I was wondering if anybody has had similar issues with this device and if there is any way to correct it.
--- EDIT 8/10/2012 ---
Another thing of note is when the device is charging, I can power it down by holding power for a few seconds, but the Soft Brick screen pops back up almost immediately upon release of the button.
I cannot boot into recovery or the standard download mode even when it's plugged in.
Click to expand...
Click to collapse
I am having this issue with my sch-i800.... phone /!\ pc screen only when plugged into the wall, and no recognition of it on the pc. Any way of fixing it?
Hello. This morning I've turned off the alarm, turned on WIFI and went back to sleep. I can't tell for sure, but I think the battery was low. During the next 2 hours I checked the time several times. I don't remember accepting any OTA. Eventually I got up, tried to check the time and the phone was off. I tried to turn it on, no effect. No matter how many times and for how long I pressed and held the power button, the green LED only flashed for a split second and that's all. I plugged in the charger, and the LED stayed lit -but- there was this barely noticeable flickering. Charged it for about 30, 60, 120 minutes, didn't start plugged or unplugged. I went to work, 8 hours later (phone was unplugged) I tried to turn it on again, this time the LED doesn't even flash, but when charging there is no flickering. No combination of buttons works. Windows doesn't find the device, neither does RSD.
I've never done anything 'custom' to the phone. The last change I made was setting the alarm to turn off by shaking (yesterday, never used this option before).
Is it dead?
Try taking SD card out and holding Vol down and then Power for 20 secs, then let go of Power,
Already done that, nothing. No matter how long I charge it now, after unplugging and pressing power button the LED doesn't even flash. Could it be a battery problem (before its death, it would last for a day)? Is there any way of recovering my data without buying a new one?
Try opening and disconnect battery for a bit.
I'll do that as a last resort, on weekend maybe since I don't have the tools with me. Any other clues?
Nobody knows how to help me?
I'm going to make a factory cable. Will this alone allow me to recover the data? Or if I'll be able to flash the phone, can I recover the data afterwards?
Also, I'm not sure if I understand correctly: does the factory cable recharge the battery or not? Is there a way to recharge it when removed from the phone?
Try to use medfield unbrick script. If You have only green led it seems to be bootloader error so this script should bring Your phone to life or Your phone has broken emmc and You can start looking for a new logic board. Good luck.
I've installed the drivers, but Windows and XFSTK don't recognize my device at all. Factory cable also didn't help. I liked my phone very much. :angel:
Did You enter medfield mode using combination with camera button??
By a combination you mean holding the camera button and connecting the phone to a pc? I tried that.
Disassembe Your phone, pull out battery, push power button for a 10 sec, plug in battery, push camera button and connect USB. If it wont help You I don't see any hope for Your phone.
Well, new option to try is a new hope. I'll try that on the weekend. Could you please be more specific:
1. Pull out the battery.
2. Press the power button and wait 10 seconds.
3. Insert the battery: should I be still holding the power button at this moment?
4. Press the camera button.
5. Plug in the usb cable (factory? regular?) - should I be still holding the power and camera buttons?
Battery trick is only to discharge capacitors. Sometimes even phone is dead it can turn on in some strange mode and then You can't boot it to flash. Thats why You need to pull out battery, push power for a few sec to completely discharge motherboard and just release this button. After that You can just plug in battery and continue normal unbrick process - so hold camera button only and connect regular usb cable.
You can also try reset option instead of pulling battery out. To do that do not disassemble Your phone but just plug in regular USB, when phone starts (green led) hold power and vol- until green led goes off and then quickly start holding only camera button.
I have no more ideas.
Ok, I've tried everything. Nothing brought my phone back to life.
Thanks for all your help.