Hi, I have installed ultrashots 2-way driver cab and have been trying to find a good auto call recorder. I tried Resco first. But when I tried mp3 for encoding, the recording which I got was broken. There were long chunks of the conversation missing here and there. I read some where that this is because of encoding error due slow cpu. X1's cpu is not really that slow for a PPC. It said in that thread that wav encoding should work fine, but wave files are too big.
I also tried Auto Call Recorder 1.24. That too showed the same problem with GSM 6.10 encoding.
I wanted to know if there is some settings of these encoders which will let me record all the calls without jitters. Or are there some other call recorder which functions well with X1.
PS: I have a stripped stock ROM (All junk media removed, ULDR removed, PP @16MB)
You have to use the resco codec pack in order to get decent mp3 recording with resco audio recorder. I've got the codec pack and I use 44100 Hz, 16 bits, 64 kbps, mono. This way I get relatively small files of decent quality.
Will using the codec pack remove skipping during call recording? That was the problem with both Resco ad ACR. Or should I try lower bitrate modes?
varun_bv said:
Will using the codec pack remove skipping during call recording? That was the problem with both Resco ad ACR. Or should I try lower bitrate modes?
Click to expand...
Click to collapse
Using the codec pack will solve all problems you described. The built in mp3 codec is just unusable. In order the get a record without interruptions you have to lower bitrate, frequency etc. until the resulting record is of really bad quality. So like i wrote before you have to get the codec pack.
Related
I think most of the active members are aware of the video difficulties SO please (please, please) turn your rants off for this thread. What I am trying to find is a combination of settings that DO work.
My preferred codec is MP4.
From some suggestions in other threads, I have tried these encoding settings.
Screen resolution: 320x240
Frames Per Second: 30
Kbps: 300
Audio codec: [email protected]
...and I am playing back on TCPMP 0.72RC1 using these settings
Options/Video: Raw FrameBuffer
Options/Video/Dither: Off
Options/Video/Pixel Aspect Ratio: Auto
Options/Settings/Advanced/Slow Video Memory: On
Options/Settings/Buffering/Preload at Underrun: 85%
Using this, all I get for video is about 1 frame every 3 seconds. Audio is fine.
So can anyone add this this for getting MP4 to work?
Do I need to use a different codec? If so, I would prefer something other then AVI, since I have a mixed environment. Does anyone have suggestions on the best cross platform Codec, that has work well on the Kaiser?
I'd be interested in this too. I can play back videos taken from the video camera flawlessly but when trying to encode them to the same MP4 codec they can get choppy. Not sure what gives :0
Using WMV here
I couldn't get the mp4 output from my ATI Multimedia Centre software to work at all on my TyTN II so I've settled on WMV 9 at 352 x 288 resolution and 372 kbps (thats at 15 fps). Anything with higher bit rate than that seems to cause problems with to much screen tearing during fast movement scenes.
You might want to follow this thread... seams that the Core Player is attacking this known problem for the Tilt. I'm by no means an expert on this, but seems like the Qualcomm QTV technology for the video has some issues:
http://www.corecodec.com/forums/index.php?topic=596.0
I use PDXE, Lathe, and a few others to encode Divx videos at 320x240 video quality at "28" audio in stereo at 96 or 128k MP3 with a total bitrate under 500k (usually shoot for 475kbps). If the encoder allows it, for portable video I bump the audio volume by 15% and I increase brightness as well. To me most movies look darker on the small screen. If cropping is allowed I crop widescreen content, cutting off some of the sides of the picture to get closer to the 3:4 ratio of PDA screen. I also like to turn the brightness down as much as possible to increase battery life so the bump in brightness helps there as well. An average movie 1:50 length is about 480MB
I've used Core and TCPMP (currently using TCPMP for the youtube capability) and use Rawframe buffer as well. I'm sure that Core 1.2 will make things even better.
I get 30FPS and normal fluid video, looks like my other 8525, hx4700, and Archos 320 and 400 units with crisp clear video, no complaints.
This MP4 doesnt play on my pc only the phone???
Flying Kiwi said:
I couldn't get the mp4 output from my ATI Multimedia Centre software to work at all on my TyTN II so I've settled on WMV 9 at 352 x 288 resolution and 372 kbps (thats at 15 fps). Anything with higher bit rate than that seems to cause problems with to much screen tearing during fast movement scenes.
Click to expand...
Click to collapse
This MP4 doesnt play on my pc only onthe phone???
I have an TiLt and when i try to record videos on my phone in MP4, it appears to work fine and i can play it back on my phone using TCPMP. but when i try to run this on my computer rnning vista it only shows video with no sound.
What can be causing this, is there a way to fix this and has anyone else noticed this..
ps. i hope ths has not been spoken about b4, i hate sounding like a nubie
zulualpha7 said:
This MP4 doesnt play on my pc only onthe phone???
Click to expand...
Click to collapse
There's lots avout video formats in the wiki here:
http://wiki.xda-developers.com/index.php?pagename=The H.264 (a.k.a. MPEG-4 Part 10 and AVC) Bible
FWIW my mp4s recorded on my TyTN II wont playback on my PC either, it's simply a case of finding a suitable codec.
recorded videos on Tilt not playing on vista with sound!! I GOT IT FIXXX
Flying Kiwi said:
There's lots avout video formats in the wiki here:
http://wiki.xda-developers.com/index.php?pagename=The H.264 (a.k.a. MPEG-4 Part 10 and AVC) Bible
FWIW my mp4s recorded on my TyTN II wont playback on my PC either, it's simply a case of finding a suitable codec.
Click to expand...
Click to collapse
Hey thanx for the reply but VLC is what i got installed and doesnt work, thought someone else had the same issue like mine. The .MP4 files that the TiLT records doesnt playback properly. PROBLEM is : I get the video portion just fine, but no sound. I have the. I tried in Media Player, VLC, QuickTime, RealPlayer, etc.... All the same... video plays but no sound.
I googled the issue and found out some other HTC phone users got it too and a couple solutions i found are.
1. In QuickTime it says: "Error 2041 - Invalid sample description in movie"
Solution: Checked the Apple.com or quicktime forums, if you use quicktime, change the file name from .MP4 to .3GP and it will work, it will not work otherwise. (if you dont know how to rename the files or dont see extension, Windows vista or XP go to tools>folder options>view>uncheck hide file extensions for known file types and voila)
2. Since I did so much reading on this, I got a new player (KMPlayer) that beats vlc in my books it plays the files recorded from the tilt just fine unlike VLC latest build, its fast and does all vlc does but it has a better GUI and plays anything you throw at it. you can get kmplayer here
Conclusion: The TiLt is fine, just that I couldnt get the right player to run the video files it records. apparently there is some issue with the qualcomm processor and the video output files of .MP4, some others have reported issues with any .MP4 files and had to do the same listed above.
Hope this helps someone here...
if you want an mp4 player on your pc for free, go to nokia.com
zulualpha7 said:
Hey thanx for the reply but VLC is what i got installed and doesnt work, thought someone else had the same issue like mine. The .MP4 files that the TiLT records doesnt playback properly. PROBLEM is : I get the video portion just fine, but no sound. I have the. I tried in Media Player, VLC, QuickTime, RealPlayer, etc.... All the same... video plays but no sound.
I googled the issue and found out some other HTC phone users got it too and a couple solutions i found are.
1. In QuickTime it says: "Error 2041 - Invalid sample description in movie"
Solution: Checked the Apple.com or quicktime forums, if you use quicktime, change the file name from .MP4 to .3GP and it will work, it will not work otherwise. (if you dont know how to rename the files or dont see extension, Windows vista or XP go to tools>folder options>view>uncheck hide file extensions for known file types and voila)
2. Since I did so much reading on this, I got a new player (KMPlayer) that beats vlc in my books it plays the files recorded from the tilt just fine unlike VLC latest build, its fast and does all vlc does but it has a better GUI and plays anything you throw at it. you can get kmplayer here
Conclusion: The TiLt is fine, just that I couldnt get the right player to run the video files it records. apparently there is some issue with the qualcomm processor and the video output files of .MP4, some others have reported issues with any .MP4 files and had to do the same listed above.
Hope this helps someone here...
Click to expand...
Click to collapse
MANY THANKS! zulualpha7,
I have had the error 2041 problem for a long time and have never been able to play vids recorded on my TyTn II on my PC.
I almost installed various codec packs as other forum members have done but after reading about potential problems of having multiple codecs for same file type and upsetting the system I decided not to do this.
I have some really important 'once in a lifetime' family moments like my friend's son catching his first fish etc... I though they were all lost for ever.
I just downloaded latest Quicktime and renamed file extensions to ".3gp" like you said and now I can watch everything!!!!
Thank you so much this really has been a big improvement for me.
ONCE AGAIN THIS FORUM ROCKS! Thanks to everyone for so much fantastic helpful info.
Hi everyone.
I know, bad video performance is a known issue (see http://www.htcclassaction.org/).
But on my device I'm not able to play any video file without bucking image. About every second, the image stops for a short instance (I get sick watching this for more than a minute )
I tried different video files with different formats:
- wmv8 with 300 kbp/s, 25 images/s, 320 x 240 with wma8 128 kbit/s stereo (converted using All-in-1 mobile video convert)
- mpeg-4 (H.264)/AVC, between 128 and 1248 kbp/s 25 images/s, 320 x 240 and 64 to 128 kbp/s for stereo audio (converted with SUPER)
- a couple other files found on the web
I tried to play them with the installed Microsoft Media Player. Normally sound is ok, video never is. For the video it seems to make almost no difference what settings I use. mpeg-4 is a bit better than wma8. But between the 1248 kbp/s and the 128 kbp/s video there is no difference (besides th artifacts), It's bucking the same.
Can anyone please tell me, what codec / settings are playable on the HTC S730? Or can someone post an example video file that plays well on his device?
Any help is appreciated!
Window's media player is your problem in this case.
I have Core player and that TCPMP one posted above. If I drop resolution on some of my files I can play them perfectly in core player, and with TCPMP set to low (medium) all videos play fine. High action scenes sometimes cause a little studder so I am going to lower the origional res down a little bit.
The only problem I have run into is on some higher quality ones the phone runs out of page file memory which I currently have set to 1024 within TCPMP. Make sure your phone's memory is clear when trying to watch stuff and you should be just fine. Especially if you are dropping the resolution down that low.
I will try to take a short video of a video playing
Works!
It works! The problem really was windows media player!
Thanks a lot for the hint - I think I'd never try to change the player...
Frame rate is not perfect yet. I still have to figure out what the best settings are, but it is already ways better than before.
Hehe, no problem. WMP is not a well optimized player. For my computer and HTPC I use zoom player, it can handle 720p on a processor that really shouldnt be able to.
Video settings
Hi all.
After spending a lot of my spare time I finally found the right settings for converting videos for the HTC S730.
First I tried to convert videos to H.264/AVC and WM8. This does not produce anything you'd like to look at. Even with very low video bandwidth (200 kbit/s for video) the best I got was below 10 frames/s. With TCPMP it's a bit better than with Windows Media Player but there is no big difference.
But if works fine with the following settings:
Container : AVI
Video Codec: MPEG-4 480 kbit/s
Audio Codec: mp3 44.1 kHz stereo 128 kbit/s
For converting I use the free SUPER (http://www.erightsoft.com/SUPER.html).
This way I get close to 25 frames/s (maybe 10% are dropped).
Please note that such a video cannot be played with the Windows Media Player. (AVI is a Microsoft format, but it looks as the player doesn't like the codec.) However it plays fine on TCPMP 0.71 (from here: http://picard.exceed.hu/tcpmp/)
My daily train rides are much more pleasant now
Luki2 said:
Hi all.
After spending a lot of my spare time I finally found the right settings for converting videos for the HTC S730.
First I tried to convert videos to H.264/AVC and WM8. This does not produce anything you'd like to look at. Even with very low video bandwidth (200 kbit/s for video) the best I got was below 10 frames/s. With TCPMP it's a bit better than with Windows Media Player but there is no big difference.
But if works fine with the following settings:
Container : AVI
Video Codec: MPEG-4 480 kbit/s
Audio Codec: mp3 44.1 kHz stereo 128 kbit/s
For converting I use the free SUPER (http://www.erightsoft.com/SUPER.html).
This way I get close to 25 frames/s (maybe 10% are dropped).
Please note that such a video cannot be played with the Windows Media Player. (AVI is a Microsoft format, but it looks as the player doesn't like the codec.) However it plays fine on TCPMP 0.71 (from here: http://picard.exceed.hu/tcpmp/)
My daily train rides are much more pleasant now
Click to expand...
Click to collapse
With my S710 (has a 200MHz TI OMAP850) I'm streaming 25fps/200kbs of my VLC server (which transcodes digital sat streams in real time). I'm using .ts container, mpeg1 vid, mp2 audio and Coreplayer as client.
I have an episode of Top Gear that I can play in TCMP at mediuam quality, its video rate is 199 / 25 fps.
WMP will only play the non tweeked files, in other words if it was compressed into any codec (xvid, divx, ogg, mkv) and other of the others WMP will not play it unless it has the codec installed. The other players (core player / TCMP) come able to read these files upon install so they work better.
With TCMP most of my files do not even have to be changed, just dump them on the sd card and with the player set to medium quality it goes right through them. Now some high action / motion scenes will cause a little lag or slow down but not much and not for long.
This is soooo ridiculous! WMP worked just fine in the older 200mhz devices! Now we have to switch to TCMP and make sure that no programs reside in memory before playing ANY videos? Ridiculous! HTC is losing a lot of faithful customers with this.
It depends on the type of file's your trying to play.
Just like WMP on the PC, it wont play anything without the codecs for them.
Hi.
I'd like to know which settings result in the best video playback on the TyTN II.
Forgive me if this is posted somewhere else, but I could not find it when searching.
I'm running WM 6.1 Sleuth 3.0 with TCPMP 0.81.
How about the best settings for Coreplayer as well. Also running Sleuth 3.0. Sleuth any comments, you seem to have Coreplayer as well.
Jckf said:
Hi.
I'd like to know which settings result in the best video playback on the TyTN II.
Forgive me if this is posted somewhere else, but I could not find it when searching.
I'm running WM 6.1 Sleuth 3.0 with TCPMP 0.81.
Click to expand...
Click to collapse
There is no best settings!
It's all about how you rip your movies!!
Have you ever heard the phrase, "Garbage in, Garbage out"
If you start out with a quality file, you won't need TCPMP to enhance or make it better.
All my movies are .avi and I use Clone DVD Mobile to rip them. Personally, I haven't had any issues playng movies with TCPMP or CORE Player.
All my settings are default
I'm copying videos that are not converted in any special way to play back good on mobile devices.
..........
dwny said:
There is no best settings!
It's all about how you rip your movies!!
Have you ever heard the phrase, "Garbage in, Garbage out"
If you start out with a quality file, you won't need TCPMP to enhance or make it better.
All my movies are .avi and I use Clone DVD Mobile to rip them. Personally, I haven't had any issues playng movies with TCPMP or CORE Player.
All my settings are default
Click to expand...
Click to collapse
guys what dwny said is right .....but also you can search online for any dvd to ipod (zune) program and it will work as good also!!
--------------------------------------------------------------------------------
SO far I noticed 2 things that effected quality of video.
I ripped 2 avi with different settings.
Video A was in 320x240 (cropped), 26fps
Video B was in 512x384 (unedited), 29fps
1) Video A played smoothly throughout. Audio lag was evident after about 1.5 hrs. Otherwise very watchable. Thus I figured 26fps is max for the Kaiser.
2) The video B skipped and dragged. Audio stayed in sync. When I selected TCPMP to play video B in full original size (overlapping the screen) it played smoother. Thus I figure that resizing is too much for the cpu of the Kaiser so when you encode, select 320x240.
fyi, audio was mp3 128kbps, 44000 on both.
I should specify what I mean by full original size.
Options --> Zoom ---> 100%
Also should specify I mean "when encoding select 320x240" MAXIMUM which will reduce the load on the cpu for video resizing.
You know, sometimes, you just happens to have badly ripped (poorly, or improperly or whatever but someone else did it and you don't have control) video but would like to watch it.
So, looking for better settings to improve the viewing.....
Latest video codec? audio codec? cache? how to set it? Where to get it from?........
transportguy said:
--------------------------------------------------------------------------------
SO far I noticed 2 things that effected quality of video.
I ripped 2 avi with different settings.
Video A was in 320x240 (cropped), 26fps
Video B was in 512x384 (unedited), 29fps
1) Video A played smoothly throughout. Audio lag was evident after about 1.5 hrs. Otherwise very watchable. Thus I figured 26fps is max for the Kaiser.
2) The video B skipped and dragged. Audio stayed in sync. When I selected TCPMP to play video B in full original size (overlapping the screen) it played smoother. Thus I figure that resizing is too much for the cpu of the Kaiser so when you encode, select 320x240.
fyi, audio was mp3 128kbps, 44000 on both.
I should specify what I mean by full original size.
Options --> Zoom ---> 100%
Also should specify I mean "when encoding select 320x240" MAXIMUM which will reduce the load on the cpu for video resizing.
Click to expand...
Click to collapse
Why wouldn't you just encode it to the natural screen size, and why wouldn't it having to resize bigger rips slow it down?
This is a pretty strange post.. Walking a mile is easier than running a mile. Walking a mile with nothing on your back is easier than walking a mile with Yoda on your back.
Common sense
I am not sure if this thread should be here, please reposition if it's not.
when i go to Voice recording format in the Input setup, i can't find any mp3 formats, is this normal? and how can I add new formats?
Use Vito Audio Notes, it allows you to record to MP3.
profahmad said:
Use Vito Audio Notes, it allows you to record to MP3.
Click to expand...
Click to collapse
what if I want to use the built in wm6.1 audio recording programs like audio recorder or notes to record mp3? i can't imagine there is no codec or plugin that we can install so wm6.1 would record mp3 on it's own
Try this, I just tested it on WM6.1. Works perfectly.
http://freewareppc.com/download/multimedia/notem.shtml
NoteM on WM 6.1 - Freezes upon closing other actions
I've used NoteM since I had my XDA way back always been a great piece of software. Lately though it continually freezes my phone. I can open it and record and usually stop recording but when I close the software or switch to another task it freezes my phone. Anybody have the same problem?
Many thanks,
Has anyone with a diamond tried this encoder? It works incredibly smoothly on mine but the problem is, the sound is always out of sync, it lags behind the video slightly, even when I play the converted video from my pc. Just wondering if it's a problem specific to the diamond or if you've had success with it. I've tried loads of settings, decreasing video and audio bitrates, normalising audio, lower resolutions down to 320x 240, VGA and WVGA with no success in synching the audio track.
http://forum.xda-developers.com/showthread.php?t=467112
No problem....
I've been using this encoder for a while now with no issues at all. I've only been converting flash videos (.flv), so I don't know about any other formats
grahamkdt said:
I've been using this encoder for a while now with no issues at all. I've only been converting flash videos (.flv), so I don't know about any other formats
Click to expand...
Click to collapse
Actually, converting those videos with encoder causes audio to be out of sync when just playing from my pc, so yeah, doesn't seem to be a diamond issue.
Another thing. I've got core player 1.2.5 now, and that's working very smoothly too, but the audio is also out of sync ( playing on the phone itself) playing flv files or anything (not converted with encoder), but not nearly as much, only by a millisecond or two, but noticeable. What is it with me and audio out of sync.
Ok, I've messed around with the manual A/V offset +/- settings in core player. I've set it to different numbers, and on a couple of videos, one flv and one wmv, at -0.550 the audio syncs perfectly. I thought I had it sorted but other flv videos are still out of synch to different degrees. I don't want to have to keep changing the A/V offset for each video. Can anyone help me further? I'm sure it's the A/V offset function that is the cause but also solution for this problem. I can't tell if it's to do with audio bitrates, video bitrates or other video/audio encodings.
EDIT: YES!! I found the right setting.
-0.200 and every single video in perfect sync with audio. Core Player, what an awesome app, it's got loads of settings to play around with. Smooth as f... video.