I just upgraded my phone to 32GB.
All was fine, I followed the instructions, replaced the card fine, got it to boot and synced up to zune. I left it while it synced.
Suddenly the phone decided to restart itself while connected to zune, when it restarted it reported that it only had 12.5mb memory.
I've replaced the card back and put in the original 16gb card and it STILL reports that it has 12mb memory, it doensn't seem to detect the card anymore.
Any Suggestions?
brummiesteven said:
I just upgraded my phone to 32GB.
All was fine, I followed the instructions, replaced the card fine, got it to boot and synced up to zune. I left it while it synced.
Suddenly the phone decided to restart itself while connected to zune, when it restarted it reported that it only had 12.5mb memory.
I've replaced the card back and put in the original 16gb card and it STILL reports that it has 12mb memory, it doensn't seem to detect the card anymore.
Any Suggestions?
Click to expand...
Click to collapse
Hello,
Try to do a Hard Reset and see if the problem continues.
Hard Reset may solve the problem.
Thanks
Santos
zeka1974 said:
Hello,
Try to do a Hard Reset and see if the problem continues.
Hard Reset may solve the problem.
Thanks
Santos
Click to expand...
Click to collapse
Hi
I've done a hard reset many times with no luck
Maybe re-format the card, it seems that wp7 puts a small partition on the card, theres some chat about it in the HD2 forum, I flashed wp7 to my hd2 the other day and when i wanted to go back to 6.5 i had to reformat my card to show the true capacity.
Try this tool from panasonic, it works really well....http://panasonic.jp/support/global/cs/sd/download/index.html
just ignor the capacity before format and when its finished it will show the original 16/32gb then try the upgrade you were doing before.
hope this works for you.
Related
hey guys,
I'm freakin' out... I followed the instructions on trinityguides.info to upload the Hard-SPL. However, even though the Active Sync is working and the RUU seems to connect to the mobile and everything if going fine so far I get this bloody 246 and that *****y thingy of a mobile is going into the three colour mode... Ok, not a big deal. As I've read in the FAQ just start the RUU again and it should be cool... well, its not... now I get a 260. Nevertheless, I've not given up yet. I tried the installation again. This time without accepting the message on the mobile, after a while I get another error 202....
so please guys... where is the trick??? I read something about go into bootloader manually - I reckon that's the camera,power and hard reset button combo. When should I do this???
I also downloaded all three of this roms, 1.20, 1.30 and the other Macrofl or so....
I'm running XP SP2, Active Sync 4.5,
Mobile: HTC P3600, IPL-0.50, SPL-1.07.0000, WM5 German
Update via SD
Hi,
I had the same kind of problem just a few days ago... and I solved it simply using my SD memory. Using it, you bypass the pc (and the connection between the PDA and PC) and all this type of problems "connection-depending".
You can flash your PDA putting the rom image on the SDcard (how you should do, you can read here here )...
Ciao
Tompo
hey tompo,
thx for your help, but I still have problems. I formated my Sandisk 2GB ultra II SD card and copied the RUU_signed.nbh to the root of the SD. Then I renamed the file to TRINIMG.nbh and went manually to the bootloader. However, there was only a short flickering of a grey screen that said "loading", after that I was back in that three colour thingy.... crap.... what the hell am I doing wrong???
seems as i have though luck with that mobile....
Any more hints???
cheers
dee-fu said:
hey guys,
I'm freakin' out... I followed the instructions on trinityguides.info to upload the Hard-SPL. However, even though the Active Sync is working and the RUU seems to connect to the mobile and everything if going fine so far I get this bloody 246 and that *****y thingy of a mobile is going into the three colour mode... Ok, not a big deal. As I've read in the FAQ just start the RUU again and it should be cool... well, its not... now I get a 260. Nevertheless, I've not given up yet. I tried the installation again. This time without accepting the message on the mobile, after a while I get another error 202....
so please guys... where is the trick??? I read something about go into bootloader manually - I reckon that's the camera,power and hard reset button combo. When should I do this???
I also downloaded all three of this roms, 1.20, 1.30 and the other Macrofl or so....
I'm running XP SP2, Active Sync 4.5,
Mobile: HTC P3600, IPL-0.50, SPL-1.07.0000, WM5 German
Click to expand...
Click to collapse
Ok.....You wanna get to the 3 strip screen?
Make sure the battery has a 50% of its charge.
-Turn the device off.(DON´T HOOK IT UP TO THE COMPUTER YET) so it should be off and unplugged.
-Press and HOLD camera button + power button,now you should see the 3 strips,if so you can hook it up to the usb port.
Got it?
I don´t remember now if you have to follow this step first:
http://forum.xda-developers.com/showthread.php?t=293957
Like I said I´m not sure,but take a look.....if you brick the phone there´s a way to fix it.
See ya.
THX
thank you guys for the support,
however, the source of the prob was the SD card. Even though I formatted the SD in my laptop with FAT32 and no label, it seemed to me that the mobile couldn't access it. I've done it several times - didn't work. Finally, I thought lets format the thingy with the mobile itself - voila - it worked.... I dono if something with my card reader is wrong... the SD was working fine with tomtom and was accessible in both (laptop and mobile) without flaws. Only the bloody flashing didn't work as it should be.... well, I don't mind any more, may be its a solution for another desperate trinity user....
Cheers guys - I'm runnin' on WM6.1 now....*sweet*
hello could you please say how did you format with the trini, cuz I'm really new and unable to find that function.
I have exactly the same problems, but no external card reader
Many thx
my mobile dosent recognize the internal memory(4GB), i made these steps but it was unsucssesful:
1.i tried to format the memory with the program in mobile but it appear an error message that its impossible to find flash nand memory.
2.i make the reset software and hardware.
anybody can help me please?
Reflash!!!!!!! From scratch up from Hardspl to ROM.
..........how?
http://modmydiamond.info/ - tells you all you need to know
I've just had the same issue and have reported it to Vodafone, I've only had the thing since Monday and have just about got it set up as I want it. . Why couldn't they just have given us a microsd slot!
A hard reset did nothing.
I'm glad I hadn't flashed the ROM yet!
Iv'e tryed to flash HardSPL to Kaiser... Downloaded various unlockers/flashers, even SD card solution... When trying to flash over usb with some Kaiser-HardSPL.exe - after entering tricolor mode and when progressbar appears it always stuck on 0%, and nothing happens... Update utility shows error (Rom update utility encountered communication error or smth.) and sugests me to do recovery. Tryed everything - SoftSpl1.56, Softspl1.93, SSpl-kais...
Other method i've tryed - SD card
Iv'e followed instructions, formatted card, copied those two files (http://forum.xda-developers.com/showthread.php?t=420683) to sd card, but after resetting Kaiser it only shows "Loading..." and hangs... no restart, nothing... just "loading..." on screen...
Bootloader menu shows following versions:
KAIS130
SPL-3.29.0000
CPLD-8
somehow... after trying another 1000 -th time... it just flashed...
Have exactly the same problem, tried all other solutions! any idea on what the last method was that worked?
When flashing via USB it will hang at 0% (and fail w/ 260 error on PC side) if the SD card is left in. I've made that mistake more than once.
Remember to remove SIM, too.
I don't have sd card and I've got the same problem...
Any ideas?
I have the same problem. I want to upgrade Hard SPL 3.24 to newer version. I always get 262 error. Also tried all possible ways (MicroSD uses FAT32, but I didn't formatted It, because I don't have SD adapter).
Sometimes It's shown that flashing complete, but HardSPL version still is the same.
Read you noobs
FOLLOW THE DIRECTIONS
http://forum.xda-developers.com/showthread.php?t=396922
latinohot, I'm doing all right...
EDIT:
I changed cable, and it went for the first time
Biker182 said:
latinohot, I'm doing all right...
EDIT:
I changed cable, and it went for the first time
Click to expand...
Click to collapse
good, also check the contact pins, sometimes they get bent.
hmmm...
i STILL can't get hardspl to work at all...just get stuck at 0%
sabzi43 said:
i STILL can't get hardspl to work at all...just get stuck at 0%
Click to expand...
Click to collapse
Are you using sspl to upgrade? sim and sd out? usb cable or sd flash? Do you already have a hspl and are just upgrading?
If you're on an original spl you must use sspl to do it.
If you're upgrading then you can use the kaisdiag file by cmonex and an sd.
aaaaahhhhh
WarByte said:
Are you using sspl to upgrade? sim and sd out? usb cable or sd flash? Do you already have a hspl and are just upgrading?
If you're on an original spl you must use sspl to do it.
If you're upgrading then you can use the kaisdiag file by cmonex and an sd.
Click to expand...
Click to collapse
I'm using usb to windows 7, sim and sd were out.
The thing is i've never done this before, but i am pretty sure i have it down...
I tried this I think 3 times then started to panic when after the recover from the freeze, i noticed things being weird, so i hard reset so i still have a functioning phone until i figure this out.
(it still has bugs it never had before :/)
ive downloaded numorous hardspls, all didnt work.
it's been one saaaaaaaaaaaad experience cuz i really want to make this happen and brag to my guy friends I FLASHED MY PHONE.
and get win 6.5, of course.
any help much appreciated!!!!!!!
sabzi43 said:
I'm using usb to windows 7, sim and sd were out.
The thing is i've never done this before, but i am pretty sure i have it down...
I tried this I think 3 times then started to panic when after the recover from the freeze, i noticed things being weird, so i hard reset so i still have a functioning phone until i figure this out.
(it still has bugs it never had before :/)
ive downloaded numorous hardspls, all didnt work.
it's been one saaaaaaaaaaaad experience cuz i really want to make this happen and brag to my guy friends I FLASHED MY PHONE.
and get win 6.5, of course.
any help much appreciated!!!!!!!
Click to expand...
Click to collapse
copy sspl.exe into your device and run it then you can flash with CustomRUU
to much better you are using ActiveSync on Windows XP
Thanks so much!!! i got it to work!!!! i actually used a jump spl instead, but i now am running win 6.5 on my kaiser!!!!!!! and i'm beyond stoked
THANKS Y'ALL!
Ok I am having the same issues. I tried to install HDWall cab on the latest march 9th energyrom with WM6.5.5 and Sense 2.5. It prompted me to restart so I did and ever since I tried rebooting it, its stuck on the bootloader. tried to hard reset a bunch of times and just goes back to bootloader. Took battery out a bunch of times. Tried to flash back to AT&T stock ROM via USB. Flash went to 100% and then when it tries to restart after flash, back to bootloader. Ran mtty1_1_.42_538 on PC and then tried to reflash to energyrom and still stuck on bootloader. The weird thing is when I try to flash via USB it the current Rom image is blank. Oh and also I attached an image of what mtty1_1_.42_538 shows when running the application. Please help chefs!!! You chefs are the brains!
bratch15 said:
Tried to flash back to AT&T stock ROM via USB.
Click to expand...
Click to collapse
I am not a chef but at this point I would do an SD flash of my favorite ROM.
Hope that helps.
I would if I could flash from a 16gb micro SD. That is the only card I have. I have read you can't flash with any card over 2GB. Don't know if its true because I don't have any other card. Card is formatted through my pc. Please help!
Something got messed up between installing HDWallpaper cab and the soft reset after.
bratch15 said:
I would if I could flash from a 16gb micro SD. That is the only card I have. I have read you can't flash with any card over 2GB. Don't know if its true because I don't have any other card. Card is formatted through my pc. Please help!
Click to expand...
Click to collapse
it doesnt hurt to try
i'm using an 8GB card and I can flash from SD with no prob
I can't flash from the microSD. I formatted FAT32 through the PC and tried putting a couple different NBH files (stock Roms and custom Roms) and neither my old fuze or my Tilt 2 read it. I don't know if it is because it is a MicroSDHC 2 card. Anybody???
For some reason my fuze and Tilt 2 will not read the card in bootloader. I'm thinking I might have a hardware issue but would like to keep plugging away at possible solutions it might be... The phone is only 2 months old so I'm questioning whether it is a software or hardware issue
In case anybody was wondering, my bootloader reads as follows:
RHOD300 32M SS-BC
SPL-0.85.OliNex
MicroP(LED) 0x0A
MicroP(KEY) 0x04
TURBO HW/TURBO SW
TP MFG DATA
522, 535 815, 860
812, 211 226, 210
232, 860 Calibrated
At the bottom of the screen it will show the USB when plugged into the PC and Serial when unplugged like it should
Possible fix
Format your card again but in 16bit.
Copy the ROM image you wish to burn to the root of the card.
Make sure it is named RHODIMG.nbh and nothing else.
Before trying to burn this rom, I would actually burn HardSPL again to your phone.
Then insert card and see if it will reburn your rom.
I am using a 16GB card in my TP2 without problems, but found I actually had less problems by formatting it to 16bit. And any access to the card was actually faster than formatting it in 32bit.
Hope this helps
I will try that tonight when I get home. Any other ideas until then?
bratch15 said:
I would if I could flash from a 16gb micro SD. That is the only card I have. I have read you can't flash with any card over 2GB. Don't know if its true because I don't have any other card. Card is formatted through my pc. Please help!
Click to expand...
Click to collapse
I think it's not a matter of capacity so much as a matter of brand. If your 16GB is from eBay you might well have a defect/reject card. I have a 4GB A-Data from Newegg that I only use for flashing. Never saw any problem with it.
bratch15 said:
For some reason my fuze and Tilt 2 will not read the card in bootloader. I'm thinking I might have a hardware issue but would like to keep plugging away at possible solutions it might be... The phone is only 2 months old so I'm questioning whether it is a software or hardware issue
Click to expand...
Click to collapse
It seems the read can not be read in two devices. That sounds like a defective card. Get your self a 2GB (non HC) card from a reliable source (maybe BestBuy) and keep it just for flashing.
I had this same problem I solved it check this thread http://forum.xda-developers.com/showthread.php?t=638825
Tried everything on the thread and still no go. Called HTC and sending it in to get fixed.
Hello guys,
now i have got a hd7 windows phone flashed with a custom ROM. (deep shining i think ...)
After the official mango update i had the first reset. The HTC-screen freezed and i couldnt do anything, so i reset my device. After that i installed a custom rom on my phone. Until now there are 8 months since the first reset and 5 hard resets. The resets werent made by me, the phone resets himself. So can you help me please ?? What can i do to stop this ?
I've already asked this in a german forum and they answered that the issue is my mini sd card ! So i tryed to change it today. I've did it but the phone didnt recongnized my new card. So i put the old card back. I looked at my new card and it was only a simple MINI SD CARD 2GB. The card of the device is MINI SD CARD HC 16GB. So my second question is, does only a mini sd HC card fit into the HD7 ?