Database Develop

Nook wont boot off Sdcard..Boots normally

no matter how many times i make the sdcard image, my nook refuses to boot off of it. Ive tried with Mac, WIndows, and Ubuntu and all failed. When i pop in the sdcard the nook just boots up normally...please someone help me. Ive been trying to get this to work since the second the first instructions were posted on nook devs

I had this problem as well. I ended up using a different USB MicroSD card reader and it worked. Try using a different MicroSD card, usually ones less than 2GB are safest, as they are not SDHC, and thus are compatible with more SD card readers...

hharte said:
I had this problem as well. I ended up using a different USB MicroSD card reader and it worked. Try using a different MicroSD card, usually ones less than 2GB are safest, as they are not SDHC, and thus are compatible with more SD card readers...
Click to expand...
Click to collapse
that might explain it lol..i've been using the 16gb that came with my galaxy s and using my phone as the sdreader
has one had success flashing the image through their phones or the nook itself?

Did you make the carding using winimage yet? For me, that was the method that worked the most consistently.
To check it, pop the card in your reader and see if there is a single ~40mb partition named nooter. That pretty much says the card is what it is supposed to be.
Unplug the nook, power it off by holding the power button until it turns off. put the card into the nook, plug it into your computer. In a little time, you should notice it saying about a new device connected, or some complaining about not being able to find the drivers. Let it go for about a minute after that and then remove the card and reboot the nook.
If it still boots normally with the card your just made, try using another card and see if that works. Also, if you have access to a mac, before you make the card with winimage (on the windows machine), use Disk utility to partition the card with 1 partition, free space.
It sounds kinda quirky, but it is how I got it to work.

I had to try 4 different computers before I found one that would work with either Winimage or Cygwin. Just keep trying different things and you'll eventually get it.

I originally tried using the Nook Color itself as the SD card reader, which did not work. Since the only USB card reader I had handy was not SDHC, I went down to a 2GB SD card, and it worked.

Help - Trouble w/Winimage
I'm using 64bit Vista and can open Winimage but when I try to install the 40Mb img file to the SD Card, all I get on the card is four files totaling about 11 Mb.
Could someone please post instruction for making an uSD image of Nooter 0.2
Thanks in advance

bobdude5 said:
that might explain it lol..i've been using the 16gb that came with my galaxy s and using my phone as the sdreader
has one had success flashing the image through their phones or the nook itself?
Click to expand...
Click to collapse
[mbm] initially had trouble as well since he was using his Nook as a card reader. Generally only dedicated card readers will reliably work. I'll go add that to the wiki page.

pokey9000 said:
[mbm] initially had trouble as well since he was using his Nook as a card reader. Generally only dedicated card readers will reliably work. I'll go add that to the wiki page.
Click to expand...
Click to collapse
did he end up using a card reader or did he get it to work?

My mistake was
Pokey9000 pointed out that I was making a simple mistake that stopped my card from working:
make sure your are writing to the whole disk, not a partition.
of = /dev/disk# (good)
of = /dev/disk#p# (bad)
I was adding the partition number to the end of my device string.

bobdude5 said:
did he end up using a card reader or did he get it to work?
Click to expand...
Click to collapse
IIRC he switched to his laptop's SD reader with an adapter and got it working.

pokey9000 said:
IIRC he switched to his laptop's SD reader with an adapter and got it working.
Click to expand...
Click to collapse
i just tried a 2gb sdcard..didnt work.. so its the reader. I hope a usb adapter will work

bobdude5 said:
i just tried a 2gb sdcard..didnt work.. so its the reader. I hope a usb adapter will work
Click to expand...
Click to collapse
via the laptop SDcard slot, the image doesn't work, and I used a USB SDcard reader, it worked.

+1 request for help
docfreed said:
I'm using 64bit Vista and can open Winimage but when I try to install the 40Mb img file to the SD Card, all I get on the card is four files totaling about 11 Mb.
Could someone please post instruction for making an uSD image of Nooter 0.2
Thanks in advance
Click to expand...
Click to collapse
+1 - despite searching and multiple efforts, I still am unable to get a useful microSD card to root the NC

docfreed said:
I'm using 64bit Vista and can open Winimage but when I try to install the 40Mb img file to the SD Card, all I get on the card is four files totaling about 11 Mb.
Could someone please post instruction for making an uSD image of Nooter 0.2
Thanks in advance
Click to expand...
Click to collapse
drbowden said:
+1 - despite searching and multiple efforts, I still am unable to get a useful microSD card to root the NC
Click to expand...
Click to collapse
That's OK!
After doing the winimage the microSD will have a 40MB partition with about 30MB free space and only about 7.5MB of files. It should work!

Finally Successful!
Finally got it done! Now on to loading useful apps and see how the NOOK holds up to work!

So excited to try and...
Grrr. both my sandisk and generic mini card readers suddenly all decide to fail/stop working and only found one of my 2gb sd cards after my move haha...
Murphy's law, such as life is..
-CC

Heya guys, Android n00b, but old time iphoney.
I to am having the same problem. I have been writing sd cards off multiple machines, bought more sd cards, etc.
Any help would be greatly appreciated! tx
Details:
Linux Mint 8 - Main
Windows 7 - tried and no success in results
Nook Color - Running firmware 1.0.1
8GB PNY HC uSD - image written sucessfully - Failed to boot in NC
2GB Sandisk uSD - image written sucessfully - Failed to boot in NC
1GB Kingston uSD - image written sucessfully - Failed to boot in NC
Latest nooter tried - auto-nooter-2.12.18.img - writes sucessfully - shows 2 partitions (NooterFiles,AutoNooter2)
Install notes:
I follow the directions to the letter. I have set up android sdk, and the other files needed from when this first became available. (I know they're not needed at the moment, but giving a history)
The image writes successfully. If I re-insert the card into my pc, then it reads as un-recognized. However, taking a leap of faith I put the card into the powered down NC. Plug in the usb cord, and it reboots just as normal.
Now after it boots. I swipe to open, and it goes into usb mode. Now my computer can see the 2 partitions listed through the nc.
Upon investigation I found that the partitions were not bootable. Aha! So I tried making them bootable. No success.
I'm at a loss, any help/points in the right direction would be greatly appreciated.

Burned wrong image - Full SDCard Access

so i either don't fully understand how images work in the SDCard itself (not on the nook), or i did something wrong and don't know how to fix the card, but at any rate, i managed to burn a 128meg image onto my 8gig sd card, didn't like the image, and now can't figure out how to get the card back to a regular 8gig card!
would love some direction. tried to search but must not be using right keywords.
didn't see any kind of format or clear option in the winimg program we're using.
thanks!

byproxy said:
so i either don't fully understand how images work in the SDCard itself (not on the nook), or i did something wrong and don't know how to fix the card, but at any rate, i managed to burn a 128meg image onto my 8gig sd card, didn't like the image, and now can't figure out how to get the card back to a regular 8gig card!
would love some direction. tried to search but must not be using right keywords.
didn't see any kind of format or clear option in the winimg program we're using.
thanks!
Click to expand...
Click to collapse
On your Nook I believe you can go to Settings, Device Info, Mount the SD card if it's not mounted and then format it. It'll erase it and you'll have a blank SD card. If you're going to put a different image on the card I don't know if you even need to bother formatting, but I' not sure about that stuff.

does the nook format work differently than a computer format? because i burned a 128meg image onto an 8gig card and now even a computer format won't get the whole 8gigs back... just the 128 megs. it's like it's got invisible partitions on it or something.

Partition
Try EASEUS Partition Manager to change the partition size/format card.

byproxy said:
so i either don't fully understand how images work in the SDCard itself (not on the nook), or i did something wrong and don't know how to fix the card, but at any rate, i managed to burn a 128meg image onto my 8gig sd card, didn't like the image, and now can't figure out how to get the card back to a regular 8gig card!
would love some direction. tried to search but must not be using right keywords.
didn't see any kind of format or clear option in the winimg program we're using.
thanks!
Click to expand...
Click to collapse
byproxy... here is the easy way...
1) Go and download "EASEUS Partition Master 7.0.1 Home Edition" --- just google it (the home edition is free and downloadable)
2) Put your microSD card into a card reader and plug into your computer
3) install EASEUS onto your computer and run the app
4) Once app is started, located your microSD card amongst the list of drives listed
5) select each one of the partitions on the SD card, and delete them individually
6) Once all partitions are deleted, make sure that you are still selecting the microSD card, and select the option to create partition (it may just say create)
7) Make sure you select FAT 32
8) Then select FORMAT
9) Lastly, click on APPLY and it will do all the things above. So in short you select all the actions that you want... and only in step 9 will it execute all those actions.
Please make sure that any changes you make are to the SD card and not any of your other drives. Last thing I would want is for you to accidentally format your Computer, NAS, or your non-SD card. =)
Enjoy...

sweet. exactly what i was looking for. thanks gents!!!

hvuong2 said:
byproxy... here is the easy way...
Enjoy...
Click to expand...
Click to collapse
OK, but isn't it easier just to do it in the Nook or am I missing something here?

...worst case there's a low level SD card formatter from Panasonic (IIRC might be Toshiba) that will do a complete low level format and has recovered uSDs for people using them with Nintendo DS dev carts...
A Google search should turn it up, or a thread on a DS site which might have a link to it. It'll be a little windows program...
(I believe that windows and most devices just do sort of a quick format of the uSD, and so can't recover from some problems like re-partitioning of the card... so monkeying around with a partition editor and assigning the card to be one big partition then re-fromatting under windows or some other device MIGHT work as well...)
[EDIT]
oops, I see post #5 has the re-partitioning solution as well... another way to do it would be to backup an image of the card BEFORE burning something like autonooter on it then restore that original image to card once finished with whatever you were trying out... it's what I did when I tried autonooter w/my old 128MB card, in linux in my case a
dd if=/path/to/sd/card of=./somefilename
dd if=./autonooter.img of=/path/to/sd/card
then later
dd if=./somefilename of=/path/to/sd/card
sd card path under linux is likely to be /dev/memc<device ref characters?>
You should also be able to do this under windows with the utility recommended for windows users to use with the autonooter image, as I'm guessing that it's just a GUI wrapper and a windows compiled version of the dd utility...
[/EDIT]

Varying opinions
BarryR1 said:
OK, but isn't it easier just to do it in the Nook or am I missing something here?
Click to expand...
Click to collapse
Some believe that there are issues with formatting on Nook... depending which ROM you are running. The surefire and safe way, is to do it from a PC.
Nook should format, but may not partition correctly.

hvuong2 said:
Some believe that there are issues with formatting on Nook... depending which ROM you are running. The surefire and safe way, is to do it from a PC.
Nook should format, but may not partition correctly.
Click to expand...
Click to collapse
No, the Nook will format the *device* and not a partition, so it always works. But you don't want to do it if you've installed NC or HC to eMMC.
If you're using Stock rooted, just boot without the card in the device, put it in, format. Done.
Or if you're on a real os just format the device... mkfs.vfat /dev/sdX

Help a noob with monster CWM and getting CM7 installed

Hi I would seriously appreciate any help! I am at a lost after hours of reading.
I had started off with autonooter, and now looking to install CM7. I had been told that I need to have the monster rootingpack. So I'm trying to go from autonooter to CM7.
I had tried to write monster clockwork... and did the 8gb clockwork, says its done but nothing shows up on my sd card. I then proceeded to format my sd card and still no luck.
I then tried to go into Rom manager and reboot into recovery but now there is an error! I'm so frustrated, I don't know what I am suppose to do.
Please let me know if you can offer help! Thanks in advanced.

Difficult to say without more - I assume you are using WinImage (run as adminstrator) to "Restore Virtual Hard Disk on physical drive"? If done correctly, there should only be four files on the drive (at which point, you need to drag and drop the zipped ROM to the drive.
Dumb question - is the flash card an 8 GB flash card?

Wile-E-Coyote said:
Difficult to say without more - I assume you are using WinImage (run as adminstrator) to "Restore Virtual Hard Disk on physical drive"? If done correctly, there should only be four files on the drive (at which point, you need to drag and drop the zipped ROM to the drive.
Dumb question - is the flash card an 8 GB flash card?
Click to expand...
Click to collapse
I yeah I used winimage as adminstrator and put the img file on and chose the drive the 8g sd card was on, click write, bar went up and it said done. looked at my sd card and there is absolutely ZERO files on it....
Appreciate asking, any thoughts?

Are you using a card slot that came with your computer? If so go get a true card reader, that may be the issue.

Schulz3 said:
Are you using a card slot that came with your computer? If so go get a true card reader, that may be the issue.
Click to expand...
Click to collapse
This is an interesting idea... is this usually an issue? I was putting my microsd card in a SD converter card and putting into a built in SDcard reader in my lenovo.
Is there a way to get my pc to read my sd card from my nook?

tmac4life said:
Hi I would seriously appreciate any help! I am at a lost after hours of reading.
I had started off with autonooter, and now looking to install CM7. I had been told that I need to have the monster rootingpack. So I'm trying to go from autonooter to CM7.
I had tried to write monster clockwork... and did the 8gb clockwork, says its done but nothing shows up on my sd card. I then proceeded to format my sd card and still no luck.
I then tried to go into Rom manager and reboot into recovery but now there is an error! I'm so frustrated, I don't know what I am suppose to do.
Please let me know if you can offer help! Thanks in advanced.
Click to expand...
Click to collapse
In order to flash CM7 you need to use the EXT4 Compatiable CWR

[Q] Problem making Win32Imager image

I'd like to copy the contents on my CM7 on an 8G Transcend uSD card to a Sandisk 8G card using Win32DiskImager on my Win 7 64 bit laptop. I've verified with EASUS that the Transcend is using the full 8G but when I create an image file it's only 4G. If I to write that to the Sandisk the process finishes almost immediately and writes nothing to the card. I've rebooted and tried several different external card readers with the same result. I have successfully used these to create 8G backup images previously so am stumped why the process isn't working this time. Suggestions?

Are you running Win32DiskImager as "Administrator"?

azj said:
I'd like to copy the contents on my CM7 on an 8G Transcend uSD card to a Sandisk 8G card using Win32DiskImager on my Win 7 64 bit laptop. I've verified with EASUS that the Transcend is using the full 8G but when I create an image file it's only 4G. If I to write that to the Sandisk the process finishes almost immediately and writes nothing to the card. I've rebooted and tried several different external card readers with the same result. I have successfully used these to create 8G backup images previously so am stumped why the process isn't working this time. Suggestions?
Click to expand...
Click to collapse
Which version of win32diskimager?
I find version "RELEASE-0.2-r23" to work best... it still always reads to about 4gig... bit it writes the image correctly.

Definitely make sure you're running with elevated priviledges (administrator). These disk imaging programs have the annoying habit of providing very little feedback when they fail due to an accounts rights issue. Took me a long time to figure this out when I first tried to install Phiremod and then again a month later when I decided to try an OC kernel (by this time I'd forgotten about the problem).

dsf3g said:
Definitely make sure you're running with elevated priviledges (administrator). These disk imaging programs have the annoying habit of providing very little feedback when they fail due to an accounts rights issue. Took me a long time to figure this out when I first tried to install Phiremod and then again a month later when I decided to try an OC kernel (by this time I'd forgotten about the problem).
Click to expand...
Click to collapse
Ahhh... as I have disabled profile to prevent the priviledges issue in win7.... I forgot about that requirement.

Jimbo67 said:
Are you running Win32DiskImager as "Administrator"?
Click to expand...
Click to collapse
Yes I ran it on an administrator account. Will have to check the version when I get home.

I had a really old version of the program. Downloaded the current version. It still creates a 4G img file but when I write it back to the new card it's the full 8G image. The contents of the boot partition look correct but the Nook just skips the SD card when booting up.
Next, I'm going to use Easeus to reduce the total used on the card to 4G, image that, write to new card and see what happens.

i have encountered win32image problem before where it fails to write to disk with erorr but when i use earlier version 0.1 it works

Followed these steps and the new card boots correctly:
- Use EASEUS to reduce the last partition so the total used on the card is 4G or less
- Use Win32DiskImager to read old card and write new card
- Use EASEUS to increase the last partition to full size.
Of course this only works if you can do the first step.
As an aside: performance with the new Sandisk card is considerable faster than the old card.

for some reason the new version of windisk imager does not write the image to the card properly for me. i always get corrupt data. i use an older windisk and everything works great. i'm on windows 7 if that makes a difference.

[Q] Guide Request

Could someone point me toward a guide that include the step by step instructions on how to reformat your microSD card after a CWM image has been burnt onto it to get it back to it's original size/recognizable in the Nook/PC.
This to me is the most frustrating part of loading ROMs on the Nook and I don't believe it's laid out step by step in any guides. They simply leave it at downloading a partition manager software tool, but not what do to within that tool.
Thanks!

I would actually recommend just buying a cheap card that you use just for flashing images. Rather than backing up, image burning, then reformatting your card each time you want to do something in CWM, spend the $6 online and buy a cheap 2GB card that you use only for this purpose. I know it isn't required, but I still use a bootable SD card with CWM recovery on it to flash new nightlies or really anything else.
I know this doesn't answer your question, but it is my solution to this problem.

While I agree you should consider a new card in case things ever go south, you should be able to put it into a card reader and format it with Windows. You can also wait until the NC is booted up and then insert the card and format it with the NC.

I actually do have a dedicated cheap card with CWM loaded on it. The problem I ran into this time was that someone had approached me with a stock nook wanting a ROM loaded onto it. So I needed yet another card to burn a root image onto. So I was stuck having to burn that image on an 8GB not so cheap card and then could never get it back to 8GB or recognizable in my PC/Nook by using various software packages.
It also causes all sorts of FCs when inserted into the Nook running MIUI. Once it's removed they go away.
Regardless, if anyone knows of a guide or the steps to doing so that actually works, it would be appreciated and I have to imagine I'm not the only one who runs into this extremely frustrating issue.

i could be wrong
but cant you boot into default nook, not booting off the microSD card and reformat the microSD card?
even if you rooted/formatted the built-in memory for android/cm7 over the nook color OS, you should be able to format the card.
the other question that i have the the OP
have you tried to access the card from all os (win, mac, linux) both through a usb adapter and through the nook directly connected to the pc/mac?

I have not had that issue with either a USB card reader or with the Nook. Do you have access to a camera that uses micro SDHC cards? You can usually format it there as well. After that, Windows should recognize the card in a reader and let you delete any folders the camera placed on it.

WWWestonC said:
Could someone point me toward a guide that include the step by step instructions on how to reformat your microSD card after a CWM image has been burnt onto it to get it back to it's original size/recognizable in the Nook/PC.
This to me is the most frustrating part of loading ROMs on the Nook and I don't believe it's laid out step by step in any guides. They simply leave it at downloading a partition manager software tool, but not what do to within that tool.
Thanks!
Click to expand...
Click to collapse
I think we need a little more information about what you are trying to achieve?
If you are looking to get your uSD back to its "fresh off the rack from the store" state, the easiest thing to do would be to just use your NC to reformat the card from within it's "Settings" area.
But, if you have loaded CM7 (or whichever ROM) onto the eMMC of your nook, then you would need to use Android's tools to do this.
When using an imaging tool to prepare the uSD, I would recommend Image Writer for Windows to write your ROM images to the uSD. It is pretty easy to use, and way better than WinImage. Use the 0.3 (Lost) release.
In my case, I just used verygreens solution of installing CM7 to my uSD, it is a one time set up and I only have to drop new nightlies onto the /boot partition whenever I want to upgrade (which is everytime a new nightly comes out, heh). I never take my uSD out of the NC anymore.
If you are looking to repartition your uSD card to get a bigger /boot partition so you can rest assured that the bigger nightlies will fit (essential if you have alternate image and ramdisk files for the alternate boot scenario), then I would follow this post in verygreen's guide.

In response to some of the questions, I am trying to get my SD card back to off the shelf so it can be used in the Nook for storage.
I have not tried on another OS to format the card. I only have Windows XP on my laptop. I could try on my Windows 7 desktop but would be very surprised if that solves the issue. I cannot see it when it is plugged in via USB adapter to my PC.
I have MIUI 1.7.22 ROM loaded on the eMMC of my Nook and using Android's format option does not work as it is greyed out.
Nothing recognizes it except for Easus Partition Manager, but I've tried everything under the sun (Deleting Partition/Wiping Partition/Assigning Drive Letter/Increasing size) and can't get it to return to a usable state.

WWWestonC said:
In response to some of the questions, I am trying to get my SD card back to off the shelf so it can be used in the Nook for storage. [snip...]
Click to expand...
Click to collapse
In Android, I think you have to unmount the uSD before you can "erase" it (thus effectively re-formating it to it's maximum size).
I would do it this way if you are able to, because you are guaranteed a uSD card that Android will recognize every time. Devices that use removable cards this way know how to properly format them. Desktop OSs treat them as removable media (i.e. like disks/discs) and do not always format them properly using a a USB adapter.
When formating SD/uSD cards on your PC, your best bet is to use an actual card reader that connects to your PC via a USB cable (like the multi-card readers).
Here is a formatting tool specifically for SD/uSD cards from the SD Association website (https://www.sdcard.org/consumers/formatter_3/). Instructions are at their website too.
Incidently, if you have access to a Mac system running OS X, the Disk Utility app in Applications > Utilities will also format your uSD and get it back to stock where Win machines have problems. I know this from personal experience.
Here is another thread, Read All About it: WP7 SD-card format working., with more formatting info that may or may not be helpful...
Short of a Mac system, you could install Linux (I recommend Ubuntu currently) in a VirtualBox virtual machine environment and give that a go in your Win7 environment. If you go this route, you also want to install the Extention Pack for USB 2.0 support. Then you end up with a more versatile OS for tinkering around in all within your Win7 evironment....