This is a simple but extremely useful modification of the Otterbox Defender case, which allows to use it with a generic lanyard (I've got mine with some digital camera). The image tells it all, but there are a few hints for a DIY person.
Start drilling the holes from the inside, not from outside. That way you can ensure they'll go through the thicker parts of that plastic prominence of the back lid.
Chamfer the entrance of each hole a little, so the lanyard wears less.
Use the lanyard from some similar by weight electronics, so it's capable to hold that weight reliably.
It's wise to get an adjustable lanyard or trim it to your hand, so you can use different "lanyard stretching gestures" while holding the device. For example I can use mine over the left hand going under the thumb while ballancing the HD2 on the side of a single index finger at the lowest part of the case - great for reading.
I've used a thin (1.25mm) drill bit, but a piece of steel wire chiseled at the end or a tiny flat tip eyeglasses' screwdriver will do the job easily. Chamfer with any knife.
Related
Shellster Horizontal Ribbed Design - Cover/Holster Combo:
----------
Available from Amazon.com (search words: LG 855 Shellster Black Belt Clip Holster)
Price: About $3.50 US ($3.50 + Free Shipping)
Materials: Hard black plastic cover and holster w/clip
Pros:
Compact
Great fit
Price
All-in-one solution
Cons:
Poor case retention in holster
No shock-absorption by case
No other color options
Belt clip only fits belts to 1-5/8" (4.1 cm)
Boxed-edges on case and holster
The "Shellster" case was my first LG P970 phone case. The price was right from Amazon (under $4, including shipping) and the on-line reviews were mostly favorable. I was impressed with the compactness of the combo, and the overall fit on the phone. I don't think the cover and holster could be made any thinner than this combo. The case sides wrap up and around the phone's sides, and sit just above the glass face surface; this case does not interfere with the on-screen keyboard in any way. The cover doesn't look like it's held on the phone by much, but it grips the phone well. My only real complaint is that the back of the cover is "boxy", with squared edges; the P970 has a beautifully rounded back that fits the hand well, and the squared edges of the cover feel out of place and make the phone appear larger than it actually is.
The holster is precision-molded and holds the phone cover face-inward. Three clips -- two on each side and one on the bottom -- hold the cover snugly in and against the holster. There is a shallow perimeter lip on the holster that helps position the cover; it also (somewhat) prevents the phone/cover from sliding up and out of the holster. A large felt pad lines the inside of the holster and protects the phone's face. A mulch-position clip securely locks the holster on a belt up to 1-5/8" (4.1 cm). The holster also has a "kickstand" built into its clip; pulling out on the clip and slipping an attached wire loop downward locks the clip outward. The stand seems to work fairly well, but I question its long-term durability.
In use, the holster didn't perform well. I immediately ran into problems with keeping the phone/cover in the holster while carrying it on my hip/small-of-back; all was well until I sat down. Sandwiched between my back and a chair/seat backrest, the phone had a tendency to work its way up and out of the holster in vertical carry. The three or four times the phone slipped out, I was able to quickly recover it. The Otterbox for the iPhone has a release latch on its holster; it's a feature that this holster sorely lacks. The holster has a raised ridge at its top to help retain the phone/case, but it's just not enough. I also ran into an issue with the belt clip: 1-5/8" clearance wasn't enough for my 1-3/4" work belt; the clip slipped over my belt, but wouldn't lock.
Rating, in three parts:
Cover - 3/5 - holds phone the well, but feels boxy in the hand, making the phone feel larger than it really is.
Holster - 1/5 - nicely built, but cover/phone retention is poor.
Overall - 2/5 - An inexpensive combo that's limited by both the lack of a retention latch and a non-contoured cover.
Hi all
I don't like any cover like holster or pocket,it's to big.
I made, better holding Note2 in one hands very simple way.
Use screen protectors,cut into small strips. Two of external lengthwise and glue on both side and inside glue few of them-yours chose how many but must be thin.
For me slip angle greatly increased.
Regards for all.
Yep!
NOTE: I received this at a discount in exchange for reviewing it.
Also NOTE: This is an outstanding case and the first fully protective case where I have given it five out of five stars on Amazon as well as here.
Please see the photos. Wireless charging works well with this case on. The phone is fully protected, front back and the sides - with this case. The only con I can find about this case is - which is not even a con - is that the two piece fit together so well that when it arrived with no instructions on how to pull it apart to insert the phone, that it is puzzling at first how to do so! DO NOT do like I did which it to try to pry the pieces apart with a knife on the front to try to open it - fortunately I did not scrape the case but soon discovered that the rubber lip on the front around the edges can be pulled back, and that is how to get the front of the case away from the back.
The pieces fit together with very tight tolerances. You first put the phone into the front of the case (and use no screen protector because one is included as part of the front of the case) - and it snaps on nice and tightly. Then you push the flexible heavy rubber-life back onto the front. When you are holding the phone case with the front facing you, and feel along the back edges on the sides of the phone, when you run your fingers up and down those edges they may feel lumpy. If you just push those lumps in then you will feel them snap into place and flatten out - this case fits the phone very well.
One thing I like in particular about this case is the raised lip around the front edge of the phone is raised higher than you will find on most other protective cases, without seeming like it is too fat around the edges of the phone. Additionally, the lip is raised less down near the home button on the phone so that there is no issue with people with large fingers trying to get the fingerprint reader to work well - another good design consideration included with this unit.
The back of the phone's hard plastic surfaces are matte so it is not at all a 'fingerprint magnet'. The indentation for the camera lens has walls that are reflective and slanted so the lens would never be obstructed by the case and there would never be any kind of shadowing affect. On the back of the phone case there are also small fake 'screw heads' that stick up and are in fact made of the heavy rubber material - and they do a good job of actually acting like nice rubber 'feet' on the back of the phone so that it will not slip when put onto a slanted surface. Although the corners and edges of the phone are made of this material, the case is still not too bulky - and not too slip resistant - to stop you from being able to slip it easily into your pocket.
The bottom edge has plugs which only cover the ports which the case designer feels would be used less often - the headphone jack and the charging port. The speaker grille is of course left uncovered and the S-Pen is actually easily accessible - the case is designed so that corner of the phone is still protected from falls, while the S-Pen is still easily reachable, which shows how well the phone case is designed. The only other case I have reviewed which had better plugs is one with plugs slightly larger than the hole with extra ridges on the side of the plug, so that it would still stay in the hole even after being pulled out hundreds of times - that is not the case here, but these plugs still fit pretty tightly and the only way to test if these would stand up to long term daily abuse is to test that for many months of wear and tear. However, I do not think that would be a problem with this phone.
To help with the grip a little better, which may be unnecessary due to the material used in this case anyway, the sides have raised ridges sticking out all the way up and down both sides of the phone. The buttons work very will and do not work so well that they would be pushed in by mistake. Additionally the buttons are easy to find by feel without looking - but in fact they still do not stick out so they would never catch on anything either!
As far as a protective rubber case for the Note 5, this one would be my top choice! Outstanding job Artech 21!
Looks like a great case, similar to the otterbox defender. Two questions? Does Tech 21 have a lifetime warranty for this case (like otterbox) and does the slot where the home button is allow too much dust in?
I am not sure about the warranty. With regards to the slot where the home button was, I only took that photo to show it was ever so slightly misaligned but forgot to mention it. I don't think any dust would get in there...
Note: I received a discount on this case in return for reviewing it.
This case is better than others which claim to offer a huge amount of protection because it is not as bulky as most of the others. One reason could be also because it does not in fact include a cover with a built-in screen protector for the front, although there are lips which do stick up around the front to protect it when the phone is placed face down on a table.
Wireless charging works well with this case as well which can be an issue with other protective cases.
The back of the phone is a shiny plastic material which can be a fingerprint magnet to a very small extent, but that is not nearly as noticeable as an issue as the phone has on the back when it has no cover. The back is also curved on the sides like the bare phone itself, so it is very comfortable to hold.
In order to make up for some possible slipperiness on the very back, you can see by the photos included that that is more than made up for by the rubber "grippy" sides. I would have preferred the side on the phone with the volume buttons to have the same rubber material all the way up the side as the side of the phone with the power button, but that is just my preference with which everyone may not agree.
On the front, the top lip and the bottom lip around the screen are hard rubber, while the sides edges are in fact the same plastic as the center of the back of the phone. They do not fit right up to the edge of the glass the same way - so on the front you can see a little of the metal edge on the top and bottom front edges of the phone with this case. However, it is just this one 'slight flaw' that makes the next paragraph possible:
It may sound counterintuitive, but what I like most about this case is that is not only a very protective case for the phone, but it is also very easy to slip on and off the phone at the same time - the rubber and plastic pieces do not have to be pulled apart from each other to put the phone in or to take it out. Just grap a couple corners and with a little effort it will pop off - not so easy that it would ever slip off on it's own - it is very snug. It may seem like a silly thing, but I have a custom proclip holder in the car (for the bare phone) - and I like to slip my phone into that when I get into the car. As that requires removing the case and slipping it back on, when I am using the other protective cases for my phone I am forced to just not use the proclip holder those times when I am driving - except not with this case!
All in all I really like this case and I'll be using it a lot!
wondermanyoulove said:
it is 4.99 dollars in Ebay
Click to expand...
Click to collapse
Probably one of the other reviewers. I still have mine.
Any ideas on a nonslip thin cover for the bottom of the Gemini or very small felt or rubber feet?
I expect to receive my unit soon.
My idea was to use silicone to create my own "feet".
The idea is to cut feet shaped holes into thin foam, the kind you would use for scrapbooking, stick the foam onto the bottom of the gemini, fill the cut out holes with a thin layer of silicone (should be neutral curing silicone, not the type that causes a vinegar smell when curing), then remove the foam molds and let it cure.
Since I haven't physically held a Gemini PDA in my hands yet I still don't know where the rear feet underneath the LCD need to be so that the device doesn't tilt backwards. Possibly the rubber feet will need to be on the metal hinge itself, which would make things a bit more complicated.
Silicone shouldn't stick that well, so I expect to loose a foot now and then and I hope that it will be easily removable without damaging the devices case.
drwatson said:
I expect to receive my unit soon.
My idea was to use silicone to create my own "feet".
...snip...
Silicone shouldn't stick that well, so I expect to loose a foot now and then and I hope that it will be easily removable without damaging the devices case.
Click to expand...
Click to collapse
Or just get wide enough grip tape to cover the entire bottom plate. That's what I plan to do with mine since cases that allow you to keep using it are pretty much impossible with this sort of device.
Oh, how nasty I can't imagine this will ever come off again
If you want to make feet, you guys should really check out Sugru! It's amazing stuff. It makes for a great present too. They should just about give me a commission, haha
https://sugru.com
I had a leftover woven carbon fiber sticky sheet that I cut to size and put on the bottom metal plate. Protects and looks good.