[Q]Odd signal issue - Galaxy S I9000 Q&A, Help & Troubleshooting

Ok, so I know it's not the csc, or the rom, or the apn settings, or the modem, or the band selection. It's not an app, or even a signal issue. It's not the service or network selection. Wiping didn't help nor did a factory reset. Every time my phone connects to an edge network, it won't connect to an hsdpa network without me going into settings, wireless and network, mobile networks, wcdma only and then back to gsm and wcdma. Any suggestions?

Anyone that comes up with a half-way decent suggestion gets a Thank You....
I'm guessing that no one has come across this before? It's not like it won't connect to HSDPA, it's just that it won't connect automatically. Believe me when I say, I've searched samsunggalaxysforum, google, and xda for a solution so I don't think this is a problem that has been posted here as of yet. Forgive me if it is and lead me to it....

Bump.
I don't think enough people have seen it before it slips into the nether regions of the forum.

I changed HSDPA revision to option 2 in band selection (HSDPA/no HSUPA). It worked off of airplane mode, which it hadn't done before but the same issue persists. When I get to work (where there is a clear HSDPA signal) from home (also clear HSDPA) it's on EDGE. During travel or when the HSDPA signal is not available, it'll just stay on that **** EDGE network even when I get to an HSDPA area.

Same problem on a clean stock rom ???
jje

Come to think of it, I'm not sure. HSDPA is new where I live but not where I work. I did, however, do a repartition in Odin of the JS3 firmware and then a wipe with Darky's 9.2 and 9.3. Of course I didn't really stick with JS3 for very long before flashing to Darky's ROM but this isn't a problem inherent in the ROM itself or others would have reported it. Furthermore, I've switched between kernels, file systems and modems and yet the problem persists. I haven't enabled any tweaks with any kernel I've used either so that shouldn't be an issue, should it?

Maybe try this.
Dial *#*#4636#*#* ->
Go to Phone Information -> and perhaps play with the Preferred network type?
If noen of your efforts have resulted in anything meaningful, the suspicion goes to your operator.
Hope this helps.

i have the exact same issue although 3G is available in my area when it once logs into edge mode it doesnt wanna change it. only when i restart the phone it logs onto 3G again.
pretty annoying
maik

You can go into wireless and settings, network settings, wcdma only, and then back to wcdma and gsm and it'll connect to 3g or H. At least that way you don't have to restart the phone every time it does it. The main thing is finding out what can fix the issue.
For some reason, the phone information settings don't stick. I've tried to use wcdma preferred but it just goes right back. The other code settings, on the other hand, work just fine.
Sent from my GT-I9000 using XDA App

I'm wondering if it may be a sim card problem rather then a phone problem. I'm thinking I should try my girlfriend's sim. I'll report back when I see if that's the problem. It'll be after work though so feel free to come up with other suggestions. I plan to do a write up in general, [resolved] if we figure out the problem so people with this issue can know what to do.
Sent from my GT-I9000 using XDA App

Not the sim. I also contacted my service provider to get a push of their latest update with tower location, it's not prl on gsm it's id-something-something. No change there really as far as the signal issue goes. I also checked my provider website just to see how much data I had used, not even close to the cap on unlimited.
I think i'll have to try a flash on odin with repartition to a stock firmware and then work my way back to see what may have caused the problem. It's a shame, really since everything else on the phone works phenomenally, it just won't auto connect to hsdpa which is spotty in my home and work area so it's a bigger pain in the neck then it needs to be if it won't switch between the two on it's own.
Sent from my GT-I9000 using XDA App

Related

No 3G since FRF83

Any solution?
Only GPRS/EDGE does work, if 3G is available, it disconnects automatically until 3G isn't available.
Solution: Set to 2G-Only :-(
Anyone has the same problem?
I didn't have this problem with FRF 72.
Provider: Sunrise Switzerland
Radio: 32.36.00.28U_4.06.00.12_7
Have you tried going into your phone settings from *#*#4636#*#* and setting it to wcdma only? I did that on mine not too long ago and no more dropping to edge for me!
-------------------------------------
Sent via the XDA Tapatalk App
andi86 said:
Any solution?
Only GPRS/EDGE does work, if 3G is available, it disconnects automatically until 3G isn't available.
Solution: Set to 2G-Only :-(
Anyone has the same problem?
I didn't have this problem with FRF 72.
Provider: Sunrise Switzerland
Radio: 32.36.00.28U_4.06.00.12_7
Click to expand...
Click to collapse
does it lose complete signal? or does it show 3g still but just not doing anything?
Mine was working at first after flash. Then at about 2am it just kept trying to load then times out. Still shows 3g but just dont do anything. Im hoping its just tmobile messing with their towers... I dont see why it would work at first then not now..
The problem is, that i can only have a internet connection, when the phone is logged in into a gsm or edge network.
as soon as wcdma is available, the phone disconnects from the internet.
the signal is always available, but it looses the internet connection when it changes to 3G mode.
when the phone changes from 2G->3G mode, i see for 1s the 3G icon and then no icon will bi there.
when it changes back from 3G->2G, the EDGE/GPRS icon is visible again.
andi86 said:
the signal is always available, but it looses the internet connection when it changes to 3G mode.
when the phone changes from 2G->3G mode, i see for 1s the 3G icon and then no icon will bi there.
when it changes back from 3G->2G, the EDGE/GPRS icon is visible again.
Click to expand...
Click to collapse
ok thanks for clarification. My problem is different. I think related to phone company.. I still show the 3g signal and even have bars, but the pages dont load and eventually gives me the check your service and try again alert....
So Im hoping soon its working again for me... And I hope you as well figure it out.....
Thank you Good luck!
Had the same issue after update, did *#*#4636#*#* and noticed I was set to GSM only. Set it to WCDMA preferred and now it's good.
Thank you very much, thats the solution!!
Andi
ezhangin said:
Had the same issue after update, did *#*#4636#*#* and noticed I was set to GSM only. Set it to WCDMA preferred and now it's good.
Click to expand...
Click to collapse
Sent from my Nexus One using XDA App
ezhangin said:
Had the same issue after update, did *#*#4636#*#* and noticed I was set to GSM only. Set it to WCDMA preferred and now it's good.
Click to expand...
Click to collapse
Thank you. Updated to FRF83 this morning and I've had a full 3g signal, just couldn't pull data all day. Could over edge. Sure enough, GSM only was selected.
AT&T N1.
I'm having the same issue on a non-rooted phone on T-Mobile. No 3G after the FRF83 update. Full bars of service and 3G displayed in the status bar. Dropping to Edge only works but there is no data with 3G.
Lost Dog said:
I'm having the same issue on a non-rooted phone on T-Mobile. No 3G after the FRF83 update. Full bars of service and 3G displayed in the status bar. Dropping to Edge only works but there is no data with 3G.
Click to expand...
Click to collapse
Same issue here.
Switching to WCDMA preferred doesn't work for me though.....any help is welcome
I think it's a hardware problem with a lot of N1's.
Mine was ok the first 2 months, and later, 3g not working. This is driving me crazy ):
I have tried everything. Change the simcard, I did a reset of the data with my telcon, and nothing happens.
I've seen these problems on many N1's.
I hope google / htc release a fix for this problem.
Lost Dog said:
I'm having the same issue on a non-rooted phone on T-Mobile. No 3G after the FRF83 update. Full bars of service and 3G displayed in the status bar. Dropping to Edge only works but there is no data with 3G.
Click to expand...
Click to collapse
how bout checking your bands in the service menu. so *#*#4636#*#* -> phone info -> press the menu key for more options -> select bands -> choose one appropriate for your region (ie "USA BANDS").
If all else fails do a factory reset by going to the settings -> privacy -> restore factory defaults.. of course do a backup/sync/whatever before just to make sure you can get all your apps back.
There's other ways to do a factory reset via the bootloader .. its under recovery and you press up volume or the trackball I think and you can just select all the clear/erase settings there and that should clear out everything on the phone's internal storage.
The factory reset worked for me (via bootloader) when I upped from update-1 to FRF50 and didn't have any data icon next to my signal strength. Could call out but couldn't get data.
Hope that helps.
jasonpich said:
I think it's a hardware problem with a lot of N1's.
Mine was ok the first 2 months, and later, 3g not working. This is driving me crazy ):
I have tried everything. Change the simcard, I did a reset of the data with my telcon, and nothing happens.
I've seen these problems on many N1's.
I hope google / htc release a fix for this problem.
Click to expand...
Click to collapse
Check your APN settings. Do a full factory reset from the bootloader. If nothing works you should call tech support again. Most 3g issues where you have issues with connecting are service/signal level related. I *****ed early about my 3g issues on tmobile and it was the network as they've pretty much gone away with improving the backhaul in my area for HSDPA+ or updates to the phone's radio.
HTC is really really really cool about swapping phones and repairing them. If you feel you have a nexus that has hardware issues call them. I did this 3 times already (one time for minor cosmetic issues with the refurb they sent) and I couldn't be happier about how willing they were to replace/repair the phone. It turns out I really didn't have any issues with them at all.. with any issues with hardware from the second refurbished phone. It was service or software related and I'm happy to say with updates/tmobile service improvements I couldn't be happier with this phone.
blisk said:
Check your APN settings. Do a full factory reset from the bootloader. If nothing works you should call tech support again. Most 3g issues where you have issues with connecting are service/signal level related. I *****ed early about my 3g issues on tmobile and it was the network as they've pretty much gone away with improving the backhaul in my area for HSDPA+ or updates to the phone's radio.
HTC is really really really cool about swapping phones and repairing them. If you feel you have a nexus that has hardware issues call them. I did this 3 times already (one time for minor cosmetic issues with the refurb they sent) and I couldn't be happier about how willing they were to replace/repair the phone. It turns out I really didn't have any issues with them at all.. with any issues with hardware from the second refurbished phone. It was service or software related and I'm happy to say with updates/tmobile service improvements I couldn't be happier with this phone.
Click to expand...
Click to collapse
Thanks blisk, but the thing I don't understand is why Blackberry 9700 with T-Mobile bands, doesn't have problems at all ?
By the way, I rooted my phone , so the thing with the warranty it's complicated
I had it happen last night at work all night, but when i got home i checked my wife's tp2 and it also was doing the same thing so for levity wasn't the phone but tmobile. They started worming the same time also.... I think its tmobile.
Hello, I had the same problem with my imported n1. I'm using the tmobile version non rooted fully stock manually updated to frf83. I did a *#*#4636#*#* and selected wcdma only, rebooted and couldn't connect to my gsm network. Went in again and did a wcdma preferred, rebooted, and I works better, still changes fast to edge and G, but less often, I'm still trying it but I have high hopes its gonna be ok
Mmmm i did have problems with 3G too after pushing FRF83, but i found out that for some reason the APN settings weren't set correctly after the update. In my case the port setting after the proxy of the APN wasn't set, i changed to the correct value and it worked.
In conclusion, check your APN settings.
Just went from FRF72 to FRF83 and it's working fine.
I'm currently set to GSM auto (PRL) in the *#*#4636#*#* and I didn't change it to that after putting on FRF83.

In need of instruction...

To give a back story on what I'm trying to accomplish, I'll explain my situation.
I work for Bell, in a retail store, the main reason I came to these forums was to find a way to re-flash phones in store to avoid having to doa what little stock we have of the phones. One of my colleagues from another location told me about the new update from Kies locking phones up at a ridiculous rate of 25%, so I'm trying to be pro-active about it.
Once I got in, I got a bit carried away with 2.2 software and what not. Now, i'm no expert, but I'm computer literate and made sense of most of the process, some extra guidance would be nice though.
Playing with the phones we have in store, I was able to flash every available software I could find on said phones, however a constant issue is found. I can not get a solid data connection. If I disable data, everything works fine, soon as I turn it back on, nothing happens.
Furthermore, I followed a thread regarding re-flashing everything back to Bell's stock settings and it didn't help me along at all.
I have done some searches, but i'm coming up dry. I know you've probably heard this hundreds of times and I'm sorry for being new to the process, some guidance towards this all would be great.
Bellkingsway said:
however a constant issue is found. I can not get a solid data connection. If I disable data, everything works fine, soon as I turn it back on, nothing happens.
Click to expand...
Click to collapse
Can you elaborate more on this?
what do you mean by unable to get a solid data connection?
what kind of data connection are you referring to?
USB cable between phone to PC?
or Wifi data
or APN (3G) data?
Bellkingsway said:
I work for Bell, in a retail store, the main reason I came to these forums was to find a way to re-flash phones in store to avoid having to doa what little stock we have of the phones. One of my colleagues from another location told me about the new update from Kies locking phones up at a ridiculous rate of 25%, so I'm trying to be pro-active about it.
Click to expand...
Click to collapse
not sure where you got that number from, but it's not that accurate
the reason for the ridiculous high amount of returned phones is due the Internal SD card problem that was found.
even under normal conditions if it gets formatted a lot or used a lot it seems to die faster than its Europe counterpart.
apparently on the Canadian version of the I9000 they use a bad batch of Flash Disk for the storage memory
there is a sticky Topic Poll about it.
it is NOT the ROM flash from Kies that are killing the units, just anything software that constantly access the internal SD can produce the same effect.
http://forum.xda-developers.com/showthread.php?t=793404
the rest of the returns you guys at Bell are seeing are due this other problem discussed here http://forum.xda-developers.com/showthread.php?t=775017
it can be reproduced, but you need the ideal conditions to do it.
it has to do with signal quality and tower availability
AllGamer said:
Can you elaborate more on this?
what do you mean by unable to get a solid data connection?
what kind of data connection are you referring to?
USB cable between phone to PC?
or Wifi data
or APN (3G) data?
Click to expand...
Click to collapse
I'm referring to 3G connection. I have set up the APN, even tried different settings, all producing the same results.
In regards to your second reply, the phones I've seen at this location for DOA's have mostly because of a failure to fully turn on, the display won't show. I've experienced similar issues when a flash doesn't work properly, a re-flash fixes it. We started seeing this issue after samsung released the update. However, I'm not going to flash a customers phone to have them lose 3G connectivity, or open up other issues.
Basically, I'm looking for two things. Primarily a way to re-flash everything to work as if it were out of box, with the latest software update. Secondly, to be able to get a stable 3G connection on 2.2, everything else seems to work fine at this point.
i'm not even going to touch the 2.2 topic as it's not even released officially.
the current stable official flash is JH2, on JH2 3G should work properly (stable), another thing you can do is to go into the service menu using the secret codes (wiki) and make sure the proper 3G bands are selected for WCDMA
1900 and 850 should both have a start next to it
next check is the *#0011* to see if the towers keeps constantly changing
that's another reason for unstable 3G if the phone keeps jumping towers every few seconds
this is also related to the 2nd link i mentioned about people getting Comatose Syndrome on the phones, which locks up the phone, and they have to reset the phone to get the phone to work again.
I'm running JH2 currently, I ran *#2263# 850 and 1900 are available. Also, ran *#0011# both are available, ran a test on youtube it worked for 5 minutes.
Any ideas?
**Edit**
I lied, on the *#0011# it only shows 1900.
Bellkingsway said:
the phones I've seen at this location for DOA's have mostly because of a failure to fully turn on, the display won't show. I've experienced similar issues when a flash doesn't work properly, a re-flash fixes it.
We started seeing this issue after samsung released the update. However, I'm not going to flash a customers phone to have them lose 3G connectivity, or open up other issues.
Click to expand...
Click to collapse
Get something straight
the update samsung released was JH2, and it is not causing the problems you've seen.
the problems with the symptoms described are after they were flashed by the Alpha & Beta versions of Froyos 2.2, which many of them do end up losing the 850 band, the band issue can be fixed with much work.
there have been at least 4 different leaks of froyo, each one bringing its own volume of chaos and bugs, the most dangerous 2 are JPH and JPK, one loses the IMEI / ESN number ID, the other one kills the internal SD
Bellkingsway said:
I'm running JH2 currently, I ran *#2263# 850 and 1900 are available. Also, ran *#0011# both are available, ran a test on youtube it worked for 5 minutes.
Any ideas?
**Edit**
I lied, on the *#0011# it only shows 1900.
Click to expand...
Click to collapse
Since the I9000M and I9000 are hardware based bands, you should always have the 850 and 1900 bands for 3G
Many who have tried Froyo and back had come across the problem of losing the 850 band, mainly because the Froyo leaks were intended for the Korea test team running international I9000 devices
some times just by flashing the Firmware back to stock or Froyo betas doesn't actually activates the 850 band, even though it shows as selected in the Service Menue
if you go back to the Band Selection screen of the Service Menue, you should choose bands that are knowingly not available in canada, like say band 900 for example, and then go back again to the service menu, and band selection to only choose 850
once you can confirm 850 works, then you can select 1900 as well, and now both of the bands should be active permanently until some body else screws it up again.
using *#0011# and trying to call the voice mail are the fastest way to verify for line and for 3G on 850
you can also try the app speedtest from speedtest.net
http://www.appbrain.com/app/speedtest-net-speed-test/org.zwanoo.android.speedtest
AllGamer said:
Can you elaborate more on this?
what do you mean by unable to get a solid data connection?
what kind of data connection are you referring to?
USB cable between phone to PC?
or Wifi data
or APN (3G) data?
Click to expand...
Click to collapse
AllGamer said:
Since the I9000M and I9000 are hardware based bands, you should always have the 850 and 1900 bands for 3G
Many who have tried Froyo and back had come across the problem of losing the 850 band, mainly because the Froyo leaks were intended for the Korea test team running international I9000 devices
some times just by flashing the Firmware back to stock or Froyo betas doesn't actually activates the 850 band, even though it shows as selected in the Service Menue
if you go back to the Band Selection screen of the Service Menue, you should choose bands that are knowingly not available in canada, like say band 900 for example, and then go back again to the service menu, and band selection to only choose 850
once you can confirm 850 works, then you can select 1900 as well, and now both of the bands should be active permanently until some body else screws it up again.
using *#0011# and trying to call the voice mail are the fastest way to verify for line and for 3G on 850
you can also try the app speedtest from speedtest.net
http://www.appbrain.com/app/speedtest-net-speed-test/org.zwanoo.android.speedtest
Click to expand...
Click to collapse
Sweet, I will try this as well.
Just a note, I have a galaxy s that is untouched, out of box and it also shows only 1900....
I'm starting to think location might be part of the issue.
there's also this sticky
http://forum.xda-developers.com/showthread.php?t=770041
with additional info you can do on the phone to get 850 back

[Q] Milestone is loosing signal - hardware or software error?

Yesterday my Milestone dropped the network and wrote "Only emergency calls". On other phones there was maximum signal. After a while the phone logged in to the network, but lost the signal again. I thought something is with the ROM, so I made a factory reset but didn't help. I flashed the correct SBF file (first Éclair, then Froyo), but didn't help. I restored an earlier MOD I used without any problem but didn't work.
I always used the German baseband files with other MODs because my Milestone is German.
The problem is that if I make anything (I mean anything related to the data connection), the GSM signal disappears, sometimes data connection remain with no problem, sometimes it is lost, too, but sometimes it has GSM signal with only EDGE network. If I do nothing, just turn off the screen and do nothing, everything goes back to normal, and the phone has normal data connection with GSM signal, I can make or receive phone calls.
I put in another SIM but the issue was the same.
Can I try something related to software and didn't try yet or this is a hardware failure? And if so, what is the price of a GSM module? I couldn't find it.
MOD: It seems that only the 3G is not working (sometimes HSPA does while 3G phone connection don't), with 2G there isn't any problem.
dial *#*#4636#*#*
Under phone info, try a different network type.
It probably defaults to GSM (auto). It does on mine anyway and it's fine.
But maybe WCDMA preferred, GSM only, or WCDMA only will work better.
It depends on which is screwing up... the WCDMA or the GSM
edit: had the dialpad code wrong... again.. geez
lordfreyr said:
Yesterday my Milestone dropped the network and wrote "Only emergency calls". On other phones there was maximum signal. After a while the phone logged in to the network, but lost the signal again. I thought something is with the ROM, so I made a factory reset but didn't help. I flashed the correct SBF file (first Éclair, then Froyo), but didn't help. I restored an earlier MOD I used without any problem but didn't work.
I always used the German baseband files with other MODs because my Milestone is German.
The problem is that if I make anything (I mean anything related to the data connection), the GSM signal disappears, sometimes data connection remain with no problem, sometimes it is lost, too, but sometimes it has GSM signal with only EDGE network. If I do nothing, just turn off the screen and do nothing, everything goes back to normal, and the phone has normal data connection with GSM signal, I can make or receive phone calls.
I put in another SIM but the issue was the same.
Can I try something related to software and didn't try yet or this is a hardware failure? And if so, what is the price of a GSM module? I couldn't find it.
MOD: It seems that only the 3G is not working (sometimes HSPA does while 3G phone connection don't), with 2G there isn't any problem.
Click to expand...
Click to collapse
Are you sure you have applied the correct baseband?
I would tell to re-apply thru AOR.
Sent from my Milestone using XDA Premium App
You could go to settings, wireless and networks and somewhere there there is use only 2g networks and if that is checked, you could try to uncheck it. That is what happened to me before on the froyo mod. Also, you could try turning on airplane mode, then turn it off. Good luck
I always used the German baseband, tried to switch 2G/3G many times, applied the baseband trough OR, applied the RTEU baseband, re-flashed the ROM, the original Éclair, the Froyo, again and again but nothing helped. I gave up I decided to go to the service. Before that on a forum somebody asked something, I gave an answer but I was not 100% sure about it, so I flashed the RTEU Froyo.
And it worked. The 3G, HSPA, 2G, EDGE, phone functions all are working now. My phone is truly German, it has QWERTZ keyboard and the original ROM was the ROM from Deutsche Vodafone (tried that one before, too), it has the logo on its box, and the German baseband files always worked. I don't know what just happened, it's simply working now. Why now... don't know.

[Q] S III mini network issue

Hi guys,
I own an i8190, baseband : I8190XXALJL and I encounter frequent network outage.
Although the signal strenght indicator shows 3-4 bars, I cannot be called, cannot call and data is not being fetched.
On battery usage app, the network is most of the time "green".
On any other phone around me (blackberries, iphones, SGS II and III), and on the same network the problem does not reproduce.
If I turn the phone to airplane mode, and then back on, I am able to call, send mails so on and so forth.
Does any of you have the same problem ?
If any of you updated to I8190XXALL2, is this problem still persisting ?
Should I send it to the service ?
I'm currently running the ALL2 baseband, but previously had both the ALJL and the ALK6 ones and didn't encounter any such issue...
Before sending it back you could try with a different SIM card, maybe yours is acting up (it sometimes happens, especially with old SIMs).
Seeing how nobody complained of a similar issue though, I don't think that changing your baseband will have an impact, but if you'd like to give it a try you can download original firmwares (that contain the baseband) from here: http://www.sammobile.com/firmware/. In order to install them, just follow the steps in the root thread.
Will do so. I'm going to pit-stop my SIM card @ Vodafone and let you know about it.
It's strange that this happens only deep inside buildings (eg. offices, malls, etc..).
When this happens, usually the data activity indicator disappears OR the S3 mini is using 3G frequencies (not H, not G, but 3G)
Just changed my sim card and the issue still persists...
It's driving me nuts. My feeling is that the S3 mini doesn't lock on a network cell when 2 are available with similar coverage.
Will upgrade to the latest build and let you know about it :banghead:
Sent from my GT-I8190 using Tapatalk 2
And now the handset runs XXALL2 from vodafone uk.
I'm curious if the phone will have that network issue furthermore.
Happy Holidays!!
Sent from my GT-I8190 using Tapatalk 2
bogdangr said:
Hi guys,
I own an i8190, baseband : I8190XXALJL and I encounter frequent network outage.
Although the signal strenght indicator shows 3-4 bars, I cannot be called, cannot call and data is not being fetched.
On battery usage app, the network is most of the time "green".
On any other phone around me (blackberries, iphones, SGS II and III), and on the same network the problem does not reproduce.
If I turn the phone to airplane mode, and then back on, I am able to call, send mails so on and so forth.
Does any of you have the same problem ?
If any of you updated to I8190XXALL2, is this problem still persisting ?
Should I send it to the service ?
Click to expand...
Click to collapse
I'm exactly in the same situation . Please let me know if your new firmware solves the problem.
Tks,
ci6i said:
I'm exactly in the same situation . Please let me know if your new firmware solves the problem.
Tks,
Click to expand...
Click to collapse
So far there's no difference. Where I live the network coverage is pretty bad, but it doesn't "disconnect in the background".
Only at the office I can test it out for sure or inside massive buildings.
ci6i, go ahead and update; install kies (for drivers only ), get odin3 1.87 and flash it with XALL2 from samfirmware.
Lately I see there is XALL3 available for some asian countries.
I still think that my BlackBerry 9810 is a tank. unfortunately vodafone romania doesn't sync emails two ways via BIS so... :crying: I had to get back to samsungs...
Well, i understand to lose signal if network coverage is bad, but my phone gets "network stuck" in the middle of town. I noticed this few times: at job, the phone stands on the table near me, and i receive sms about missed calls (i have voice calls diverted to voice mail when unreachable). If i try to call or browse the net at this moment, it's impossible until i set airplane mode on then off. All this time, the phone shows full network signal and HSPA data connection.
I'll try to change the firmware after hollidays.
As mentioned above, try to change firmwares (to XXALL2), I've also noticed some network drops when I'm at home (however this is expected in my case), but when I installed this firmware, I noticed some signal gain (full on 2G and +1-2bars on 3G signal).
Hi again.
The same issue even on xall2
Just happened again today in a crowded place.
It goes to "3G" from "H" and then it's gone off the network.
Will try with XALL3 although there is a small improvement concerning "sticking to the network carrier". It seems it'a hard job to get a call when in coverage area...
If still no success, I'll loose my patience with this Sammy...
See ya!
Sent from my GT-I8190 using Tapatalk 2
You get SMS because they use a dedicated network bandwidth for this technology and apparently the S3 mini does not loose connection on this communixation channel.
It appears that S3 mini is dropping voice and data, but not sms and CB (cell broadcast).
Sent from my GT-I8190 using Tapatalk 2
LJL version. No drops. Sometimes when i am on edge of 3G coverage area
Sent from my GT-I8190 using xda app-developers app
Hi, i also have the problem with vodafone Romania. I can't place calls or use data connection. After reboot everything is ok. I tried to switch to Airplane mode and back, but no results.
Same problem over here
bogdangr said:
Does any of you have the same problem ?
If any of you updated to I8190XXALL2, is this problem still persisting ?
Should I send it to the service ?
Click to expand...
Click to collapse
Hi bogdangr,
I have the same problem with my SIII mini. From time to time, after working normally, it loses the H or 3G symbol and shows about two or three signal bars, but if I try to make a call or receive one the operation fails miserably. The airplane mode trick doesn't work for me, and I have to reboot the phone to get it working again.
I've updated to the latest official firmware, but the problem is still there. Have you found a solution for this or anybody has more ideas of things to try?
Thanks you all,
MFC
I'm on VF RO, too.
Crappy phone, what can I say.
If it can't follow a network where there is sufficient coverage...
miguelfc said:
Hi bogdangr,
I have the same problem with my SIII mini. From time to time, after working normally, it loses the H or 3G symbol and shows about two or three signal bars, but if I try to make a call or receive one the operation fails miserably. The airplane mode trick doesn't work for me, and I have to reboot the phone to get it working again.
I've updated to the latest official firmware, but the problem is still there. Have you found a solution for this or anybody has more ideas of things to try?
Thanks you all,
MFC
Click to expand...
Click to collapse
Hi Miguel,
The only workaround for this issue (at least for me) is to keep it in GSM mode (no "AUTO mode", no "WCDMA only").
So the crappy phone won't have to switch frequencies and I can get phone calls (I start considering a luck when the phone rings...)
I'm on 4.1.2 now baseband I8190DXALL3 (latest on samfirmware) and still the same.
You just don't want to know how's everything downloading limted to GPRS
BR,
Bogdan
Does anyone know what's that *# code that enables service / engineering mode ?
I want to select on which network frequencies is the phone allowed to work.
I want to disable 3G mode and leave GPRS, EDGE, and HS(D)PA only.
The reason is that when the issue appears, S3 mini switches from "H to 3G" and "G to 3G" and then it's gone;
Although there are moments when it can fetch data with network on 3G coverage without problems...
The code is *#*#info#*#* but it doesn't work .
I don't think it's a good ideea to disable those settings. Maybe it's a temporarily problem and i know Vodafone is testing/launching 4G coverage.
For me, this network issue is happening once in a week. How often do you lose phone signal ?
ci6i said:
The code is *#*#info#*#* but it doesn't work .
I don't think it's a good ideea to disable those settings. Maybe it's a temporarily problem and i know Vodafone is testing/launching 4G coverage.
For me, this network issue is happening once in a week. How often do you lose phone signal ?
Click to expand...
Click to collapse
I found out the service code but the RF setup is not "sufforted".
Vodafone has implemeted already 4G in selected areas but it's not about that. On blackberry, iphone and nokia this is not happening.
As a frequency... 3-5 times a day while I'm at the office.
Sent from my GT-I8190 using Tapatalk 2
I'm using it with Orange Spain. I will try using the phone this weekend with another operator to find out if the problem is operator related.

3g not working if radios set to 3g only?

I noticed if I go to the mobile networking settings and have it it on lte/3g if I leave a 4g area, 3g works ok. If I put the toggle specifically on 3g it shows I have 3g, but anytime I tried to search google or access a data connection the signal goes away and gives me the signal with an exclamation point. I tried finding info on this, but didn't see anything when I searched. Anyone else have this issue? I am on Sprint with the 64gb white device. Thanks
I leave mine on 3g due to the lame multiple text issue. It has no problem staying on 3g. Perhaps try updating your PRL/profile and see if that helps.
I don't have 3g either if I set it to 3g only. I don't leave lte service too often to test whether 3g works when it switches on its own. I may have to make a trip to the mountains to test it. I do know that my old Note 2 would loose lte after flashing tons over and over and I would have to flash back to 100% stock the factory reset from the settings app to fix it. I may try this with my Nexus, about time for a wipe anyway.
Factory reset does not fix it. Just noticed that I don't even get 3g when it is set on LTE. I'm gonna go talk to my cellular provider about it.
I don't know why it wouldn't work. You did update profile and PRL also right? Here's some shots of mine and it's working fine.
I have a bad Sim.....I also don't have a phone number as well..... I swiped with an old card I had and my number appeared, I guess I'll be visiting the store tomorrow to get a new one. Maybe it'll fix my 3g. Its also not wanting to let me pick 3g as an option now, just stays on LTE.
KB112 - Are you on sprint also? I updated prl/profile and no luck still. 3g still works if I am on lte and go into a 3g zone, but if I toggle it to 3g only I get no data. Wondering if its a sprint thing or a lollipop bug on Sprint, or a bad sim, missing feature activation.
Bluemgt06 - did a new sim fix it for you?
Sorry, didn't see this earlier. But yes, I am on Sprint. My 3G would work fine if I set to 3G only. Not sure why yours has issues with this?
Oddly I tried it today and it started working. I think it could have been some kind of issue with the tower/upgrades or a bug that a reset may fix on occasion perhaps.

Categories

Resources