Related
I installed Nookie Froyo to the EMMC and got it working enough using Clockwork Recovery. When I signed in for the market, I realized I used the wrong account so I was going to restore to factory settings to change the account.
Now my NC won't even turn on no screen light up, nothing, is there anything I can do to save it?
I was running the Customized Nookie Froyo seen at http://forum.xda-developers.com/showthread.php?t=922324
I have tried the stock repair on the SD card suggested in the developers forum but the nook wont do anything.
I'm having the same issue in 0.6.6. At one point I got it to say "loading" on the screen, but I realized the SD card I had in was not working. Haven't been able to get it up since.
Have you tried connecting it to a computer? I have been switching where I connect the usb cable to and see if it helps.
Flash my boot repair on my froyo on emmc thread..
Sent from my HTC Desire using XDA App
Well I don't know what I did but this morning when my nookie froyo emmc was at 20 percent it decided to turn off and not turn on and won't turn on when charged and will not boot any sd cards. I feel stupid but after my nook working on emmc froyo for a week and now its not even turning on I feel very stupid. All help is appreciated, thanks!
Sent from my ADR6300 using Tapatalk
Have you tried booting to the CWR card yet? And using Samuelhalff's zip that restores the stock partitions? This seems to have worked for many people experiencing the fatal Froyo crash. Take a look at the 'Easily Restore to Stock" thread found here in the Nook forums. And in the end if your device truly won't turn on, then chances are the guys down at B&N won't be able to either. *Warranty*
Well I have tried monster root pack as a card but I haven't tried stock partitioning,i dont know where the thread is. But will this let me even boot an sd card ?
Sent from my ADR6300 using Tapatalk
RileyGrant said:
Were you running froyo off emmc? If so:
http://forum.xda-developers.com/showthread.php?t=931720
I recommend flashing this ROM instead though (pre-rooted 1.1):
http://forum.xda-developers.com/showthread.php?t=932145
And yes if you insert the CWR sdcard into the nook and hold the power button, it will power on. The reason it isnt powering on currently is because your froyo boot partition is corrupted, not because of the nook itself. The CWR sdcard has a different boot partition that your nook will see and boot to when you hold the power button down with the CWR sdcard in.
Click to expand...
Click to collapse
Thats my post from an earlier thread with someone having the same issues. It worked for him, it should work for you. Just make sure you follow the steps right and especially make sure your burning the Clockwork image to your SDcard correctly that way it will boot into Clockwork instead of staying black.
I'm gonna have to give these steps a whirl. The downloads are taking foreeeever.
Also had Froyo installed with CWM and just got finished installing gapps. I went to format an SD card, had no luck, and tried to reboot. Ol' Nookie decided not to come back to life after that.
edit: wait, instead of flashing the stock rom can I flash the pre-rooted 1.1 rom?
Just read this over on android central (in a thread about flashing honeycomb). I believe it is what I did and why my nook won't boot:
****While running Honeycomb from Internal Memory NEVER choose the option to format your SD Card from within Honeycomb. The files that were altered to let HC run internally will lead the OS to actually format your boot partition instead of your SD. If you need to format an SD, do it on your computer or in an Android phone, etc.*****
Click to expand...
Click to collapse
Drat. Just got my CWM image on my sd card. Here goes nothin! Will report back
OK, I have CWM booting off the SD card, i'm formatting system and data under mounts and storage, and then i'm installing the 1.0.1 complete restore. It goes through and then I got to reboot system. Then...nothing. Back to black screen. Help please!
I can pop the SD card back in and boot back to CWM. I've tried several times now with no luck
samuelhalff has a flashable zip that restores the boot partition for situations like this. Go look for it in the development forum. you should be able to flash it using CWR and your NC ought to boot.
eyecrispy, thank you! samuelhalff's boot zip followed by his 1.0.1 complete restore zip did the trick.
RileyGrant, thank you for your post as well. Much obliged!!
Mine just shows a blank screen. All I did was boot into ClockwordMod Recovery, make a backup, then reboot. I was going to flash the Honeycomb Rom, but decided to give it some more thought first. Now All I get is the blank screen, it won't power all the way off, and it won't power on or anything
EDIT: Managed to get it to turn off, but when I turn it back on it boots into recovery. I select Reboot System now, and it reboots back into recovery. Forgive me, I'm so new to this Nook Color thing lol
EDIT AGAIN: Tried using the Monster Pack or whatever, flashed the removeclockwork.zip, followed by the installclockwork.zip, then removed the SD card, rebooted, and went right back into Clockwork Recovery. What gives?
YUP Same thing happened to me. I have read all the posts in this thread and i did try to format the card i had in my nook in the brand new phiremod froyo rom. Now it wont boot at all. I have a CRW card on hand and it wont even boot that. Idk right now, nothing is working.
Try reading through the Dummies Guide to Fixing 'My Nook Won't Boot'.
I did it last night and I'm back up and running again. Here's my post for an abridged version of what I did last night: http://forum.xda-developers.com/showpost.php?p=11374824&postcount=29
I had the same problem until I flashed the repartition fix.
Give that a try
I've got the exact same problem as the OP. Running Froyo on EMMC with no problems for a few days, then I left it for a while and now it wont turn back on or boot from uSD.
I've tried long presses on the power key, usb cable power up, but nothing works. I've tried the v4 HC image and the clockwork recovery image and neither are booting.
I verified the CWR image on my android phone and it does boot on my phone, so the image is definitely okay.
Hate to think it, but could this be a battery management issue in the 0.6.7 image and the battery is now screwed? Doesn't seem like boot partition corruption to me.
Any comments or suggestions are welcomed
ChrisAC84 said:
Mine just shows a blank screen. All I did was boot into ClockwordMod Recovery, make a backup, then reboot. I was going to flash the Honeycomb Rom, but decided to give it some more thought first. Now All I get is the blank screen, it won't power all the way off, and it won't power on or anything
EDIT: Managed to get it to turn off, but when I turn it back on it boots into recovery. I select Reboot System now, and it reboots back into recovery. Forgive me, I'm so new to this Nook Color thing lol
EDIT AGAIN: Tried using the Monster Pack or whatever, flashed the removeclockwork.zip, followed by the installclockwork.zip, then removed the SD card, rebooted, and went right back into Clockwork Recovery. What gives?
Click to expand...
Click to collapse
how did you get yours to turn off, my screen says loading... and is stuck there. any help in getting mine to shut off would be helpful
Does holding power button for a few seconds turn it off?
Same thing happened to me, this fixed my problem: http://forum.xda-developers.com/showthread.php?t=986977
Sorry for asking what's probably a silly question, but I haven't seen an answer. Is this known to the Nookie dev(s) and being addressed? Just had it happen running Nookie 0.6.8 off the SD card. I was really enjoying it and just telling the wife how I think I'll flash it to the eMMC, but I might have to reconsider if this might occur. Battery was ~80%, no goof-ups reformatting anything. Locked the screen around 1:10 this afternoon & hadn't touched it since. Got home about an hour ago to turn it on, nothing. Disappointing, Nookie is pretty good!
nook color wont turn on
so what to do if i dont have a sd card with cwr or honeycomb (what i was trying to run)ive already called for the replacement, but i would still like to know what to do.
I found this thread after suffering the same or similar problem to everyone else. I turned off the screen and set my nc aside for a few minutes, then it would no longer boot. Screen just stayed black and was completely unresponsive to any input. Working my way through some troubleshooting, I plugged the nc into my computer via USB and it booted into CM7 instantly. I have no idea why this happened, but it's working fine now.
Hey guys,
I have a rooted Nook Color, that was running CM7 (very smoothly to say the least), and now it won't boot. Last time it actually turned on was a few days ago and I turned it off, at that point, and now it won't turn back on.
The really weird part is that if i put in my recovery sd card, it'll boot into recovery just fine. From there I've tried to flash pretty much every rom, take out my recovery sd card and boot.. with no avail (on the booting part).
If anyone knows how to get my nook to power on, i would be the happiest guy ever.
P.S. I've tried the whole 'hold power for 10 secs and plug in to have it turn on' deal, and even that doesn't work.
[EDIT] I found THIS xda page that helps you re-format boot. So if you have the same problem go here.
ryanolson7 said:
Hey guys,
I have a rooted Nook Color, that was running CM7 (very smoothly to say the least), and now it won't boot. Last time it actually turned on was a few days ago and I turned it off, at that point, and now it won't turn back on.
The really weird part is that if i put in my recovery sd card, it'll boot into recovery just fine. From there I've tried to flash pretty much every rom, take out my recovery sd card and boot.. with no avail (on the booting part).
If anyone knows how to get my nook to power on, i would be the happiest guy ever.
P.S. I've tried the whole 'hold power for 10 secs and plug in to have it turn on' deal, and even that doesn't work.
[EDIT] I found THIS xda page that helps you re-format boot. So if you have the same problem go here.
Click to expand...
Click to collapse
I'm having the exact same problem. I'll follow that thread. Thanks for updating your post!
[HOW-TO] : Restore Nook Color back to stock EASILY!
Completely resets Nook to out of the Box condition.
Works every time
____________________________________________________
Sent from NookColor CM7 uSD using Tapatalk
japzone said:
[HOW-TO] : Restore Nook Color back to stock EASILY!
Completely resets Nook to out of the Box condition.
Works every time
____________________________________________________
Sent from NookColor CM7 uSD using Tapatalk
Click to expand...
Click to collapse
How is that possible if you can't get it to power back? I burned the clock recovery on it and the rootkit and it won't power on at all to even pick up the files.
mrairbrush said:
How is that possible if you can't get it to power back? I burned the clock recovery on it and the rootkit and it won't power on at all to even pick up the files.
Click to expand...
Click to collapse
Just because the backlight isn't coming on doesn't mean it's not powering on
To the OP: sounds like you broke something in the boot partition. Follow the link japzone sent and see if that fixes it.
Not sure what I did while in recovery, but it was looping after trying to update Phiremod with a auto update. Screen went black and ever since my pc with not recognize the nook being plugged in nor will it boot into recovery with the appropriate zip and image on my sd card.
Any clues would be much appreciated
PapaMag said:
Not sure what I did while in recovery, but it was looping after trying to update Phiremod with a auto update. Screen went black and ever since my pc with not recognize the nook being plugged in nor will it boot into recovery with the appropriate zip and image on my sd card.
Any clues would be much appreciated
Click to expand...
Click to collapse
There's no way you bricked an "unbrickable" device. You may just have to create a CWM SD and restore your previous Phiremod ROM.
P.S. SD boot priority ROCKS!!
natoe33 said:
There's no way you bricked an "unbrickable" device...
Click to expand...
Click to collapse
Challenge Accepted!
The first thing to try if you're getting no response is to hold down 'n' while powering on and see what happens. Otherwise, hit the pinned "My Nook won't boot" thread in General.
Try booting with no SD card in. If that works some Androids I have played with don't like to boot with the ROM zip on the root. The nook especially gets stuck trying to boot from the SD when there is nothing to boot on it.
Sent from a CM7 DInc2
I am just saying I have tried all of the above and there is no response from my nook. I have the CMW SD and nothing, I have tried holding down the n while powering on, nothing I have tried booting with no SD, nothing. I have been all though the Pinned thread my nook won't boot, tried it all, even bought a new sd card just in case, nothing
PapaMag said:
I am just saying I have tried all of the above and there is no response from my nook. I have the CMW SD and nothing, I have tried holding down the n while powering on, nothing I have tried booting with no SD, nothing. I have been all though the Pinned thread my nook won't boot, tried it all, even bought a new sd card just in case, nothing
Click to expand...
Click to collapse
What program are you using to burn the clockwork card?
Sent from my LG Optimus V using Tapatalk
Win32Diskimager, I think I'm stuck until my pc with recognize the device. The light on the Nook Power Cord changes from yellow to green like it's supposed to. Can't imagine the port on the nook just going bad at the same time but maybe that's the case.
just got back from Barnes and Noble, they could not get the Nook to be recognized on their computer with a new cord either
PapaMag said:
Win32Diskimager, I think I'm stuck until my pc with recognize the device. The light on the Nook Power Cord changes from yellow to green like it's supposed to. Can't imagine the port on the nook just going bad at the same time but maybe that's the case.
Click to expand...
Click to collapse
Did you make sure to run as admin and check the MD5?
Sent from my LG Optimus V using Tapatalk
yes everything has been done over and over, the nook is not recognized by the pc which in turn won't allow me to boot to anything.
wonder if the screen went bad
but then again, if it is powering on and the screen is bad, you should see it via adb
if the port and the screen went bad, then you didnt brick it per say, but its just hardware failure.
if its under warranty and registered, id say try to get it rma'd
if it is truely dead, they cant say that you voided the warranty
The sdcard adapter being used to burn the cwm or cyanogenmod install can influence whether or not the nook will boot from it.
Try burning the sdcard using a different adapter. I ended up using both the nook itself as well as my phone plugged into my PC as any attempt to boot from an sdcard burnt from the adapter that came with it will not even power on when inserted into the nook.
Hope this helps.
Sent from my NookColor using XDA Premium App
After several attempts and a few SD Cards I am back up and running. Thanks for all the advice and help. I believe it was a bad image, finally got it restored, rooted and running cynogenmod once again
I saw in the other forum. Glad you got it working.....
leapinlar: Ask the question on the forum. I don't like using PMs.
Recently the update allowing google play store somehow bypassed the anti-update thing on my nook, so now I can use play store on the nook home, but the update removed my root but kept the android system home.. It uses a lot of ram, which i'd rather have free to play games or other resource heavy apps on.
I know I have to get my nook to start unsuccessfully 8 times, but I don't know how I go about doing that, can I get some help?
flipperz said:
leapinlar: Ask the question on the forum. I don't like using PMs.
Recently the update allowing google play store somehow bypassed the anti-update thing on my nook, so now I can use play store on the nook home, but the update removed my root but kept the android system home.. It uses a lot of ram, which i'd rather have free to play games or other resource heavy apps on.
I know I have to get my nook to start unsuccessfully 8 times, but I don't know how I go about doing that, can I get some help?
Click to expand...
Click to collapse
If you want to do it the easy way, just interrupt the boot by turning it completely off (hold power button for a few seconds) while booting eight times in a row. It will take you back to some version of stock, usually 2.0.0 or 2.0.4 then upgrade again to 2.1.0 when you register again.
Sent from my Nook HD+ running CM10.1 on emmc.
Another way
leapinlar said:
... just interrupt the boot by turning it completely off (hold power button for a few seconds) while booting eight times in a row. It will take you back to some version of stock, ...
Click to expand...
Click to collapse
After my HD+ locked up when I created a "Guest" ("child") profile and I had to do the 8-reboot process, after upgrading to B&N v2.1.0, I experimented with alternate button combinations at power-on. If I held the "n" button when pressing "power", I got a prompt that allowed me to do a factory reset.
Whether that is part of a later B&N recovery module, I can't say.
DeanGibson said:
After my HD+ locked up when I created a "Guest" ("child") profile and I had to do the 8-reboot process, after upgrading to B&N v2.1.0, I experimented with alternate button combinations at power-on. If I held the "n" button when pressing "power", I got a prompt that allowed me to do a factory reset.
Whether that is part of a later B&N recovery module, I can't say.
Click to expand...
Click to collapse
That factory reset just wipes data, it does not reinstall the ROM. He probably needs to reinstall the ROM since some of the broken symlinks may still be in /system.
Power + n takes you to stock recovery, which, without other parameters being passed to it, asks if you want to factory reset.
Sent from my Nook HD+ running CM10.1 on emmc.
leapinlar said:
That factory reset just wipes data, it does not reinstall the ROM. He probably needs to reinstall the ROM since some of the broken symlinks may still be in /system.
Power + n takes you to stock recovery, which, without other parameters being passed to it, asks if you want to factory reset.
Sent from my Nook HD+ running CM10.1 on emmc.
Click to expand...
Click to collapse
Thanks for the help!
I'd like to return my Nook HD+ to stock, too. It has a Cyanogen mod that precedes that startup, and I think that's getting in the way of the 'eight reset' mechanism for a total factory reset to stock software.
Is there a bootloader, system, and gapps zip that I could just flash from an external SD card that would do the job? Seems like there was, at one time, but it's getting very difficult to find them. Any ideas for a quick factory reset (not a wipe, but a complete reset to original OS?).
[email protected] said:
I'd like to return my Nook HD+ to stock, too. It has a Cyanogen mod that precedes that startup, and I think that's getting in the way of the 'eight reset' mechanism for a total factory reset to stock software.
Is there a bootloader, system, and gapps zip that I could just flash from an external SD card that would do the job? Seems like there was, at one time, but it's getting very difficult to find them. Any ideas for a quick factory reset (not a wipe, but a complete reset to original OS?).
Click to expand...
Click to collapse
Go to my HD/HD+ CWM thread linked in my signature and flash the plain stock zip from item 6 there and follow that with a factory reset by CWM.
And it was not the cyanoboot that prevents the 8 reset, it is because when you originally installed CM you also replaced the stock recovery on internal memory with CWM. Stock recovery is needed for the 8 reset to work.
Sent from my BN NookHD+ using XDA Premium HD app
Thanks, that worked. I also tried the rooted version of stock, but it has a problem: "Unfortunately, Home has Stopped". Is there a workaround to this?
[email protected] said:
Thanks, that worked. I also tried the rooted version of stock, but it has a problem: "Unfortunately, Home has Stopped". Is there a workaround to this?
Click to expand...
Click to collapse
Don't use that version, I should remove it. If you want to root, do it per the thread with universal root rev 3.
Sent from my SCH-i705 using XDA Premium HD app
Hi there,
I have a device that is also candidate for unrooting to stock. The thing is that I have tried both CWM and TWRP on bootable SD to try and fix the situation tith the apropriate zips but unfortunately none of them can mount sd ot any internal memory for me to reset.
Maybe I should also add that the device is charging without turning on except if there is a proper bootable sd inserted.
I presume a rescue bootable SD of OEM type could bring the device back to life.
I`ll apreciate any help.
ValentinD said:
Hi there,
I have a device that is also candidate for unrooting to stock. The thing is that I have tried both CWM and TWRP on bootable SD to try and fix the situation tith the apropriate zips but unfortunately none of them can mount sd ot any internal memory for me to reset.
Maybe I should also add that the device is charging without turning on except if there is a proper bootable sd inserted.
I presume a rescue bootable SD of OEM type could bring the device back to life.
I`ll apreciate any help.
Click to expand...
Click to collapse
When you say a candidate for stock, why? Is there something else wrong with it? I am just trying to see if it is bricked.
Sent from my BN NookHD+ using XDA Premium HD app
leapinlar said:
When you say a candidate for stock, why? Is there something else wrong with it? I am just trying to see if it is bricked.
Sent from my BN NookHD+ using XDA Premium HD app
Click to expand...
Click to collapse
Maybe Bricked is the situation. The device is charging (the green light is present when plugged to the charger or USB ) but the power button can no longer start any visible boot process on the screen.
The story of the device is nearly the following:
I was using the device for a long time rooted with installed CM updating even with over night builds from time to time.
Once I had a problem booting properly after update but easily booted to TWRP and restored the previouse update.
A week ago the same situation occured, after an update procedure I left the device plugged to the wall charger and on the morning it was stuck on the CYANOGEN universal boot logo. No way found to boot to recovery found.
I figured the recovery has gone bad. Started to prepare bootable SD to try and fox the mess somehow, but could not do the corect procedure of preparing a good bootable SD many times. The only time I successfuly booted CWM recovery from SD I tried to install a zip with CWM recovery and as far as I remember at that time the bootable recovery was able to mount another SD wile it was booted on the device and the zip installed with success according to the software. Sadly after a restart the device was as is, stuck on the bootloader logo.
After 2-3 times successfuly booting both CWM and TWRP recoveries from prepared SD card, doing nothing at all that can alter the device, just tried to see how to mount any usable memory, the device stopped visualy booting without an SD.
Thank you for the reply, hope you can add some wisdome to the happy end
ValentinD said:
Maybe Bricked is the situation. The device is charging (the green light is present when plugged to the charger or USB ) but the power button can no longer start any visible boot process on the screen.
The story of the device is nearly the following:
I was using the device for a long time rooted with installed CM updating even with over night builds from time to time.
Once I had a problem booting properly after update but easily booted to TWRP and restored the previouse update.
A week ago the same situation occured, after an update procedure I left the device plugged to the wall charger and on the morning it was stuck on the CYANOGEN universal boot logo. No way found to boot to recovery found.
I figured the recovery has gone bad. Started to prepare bootable SD to try and fox the mess somehow, but could not do the corect procedure of preparing a good bootable SD many times. The only time I successfuly booted CWM recovery from SD I tried to install a zip with CWM recovery and as far as I remember at that time the bootable recovery was able to mount another SD wile it was booted on the device and the zip installed with success according to the software. Sadly after a restart the device was as is, stuck on the bootloader logo.
After 2-3 times successfully booting both CWM and TWRP recoveries from prepared SD card, doing nothing at all that can alter the device, just tried to see how to mount any usable memory, the device stopped visualy booting without an SD.
Thank you for the reply, hope you can add some wisdom to the happy end
Click to expand...
Click to collapse
It sounds like it is bricked. If recovery said it installed successfully and it still will not boot normally, it is usually what that means. By bricking, I mean internal memory has become read only and nothing can successfully be written to it even if it said it was successful. Your probable only option is to use a noemmc version of SD CM. Search the dev forum for that term.
Sent from my BN NookHD+ using XDA Premium HD app
leapinlar said:
It sounds like it is bricked. If recovery said it installed successfully and it still will not boot normally, it is usually what that means. By bricking, I mean internal memory has become read only and nothing can successfully be written to it even if it said it was successful. Your probable only option is to use a noemmc version of SD CM. Search the dev forum for that term.
Sent from my BN NookHD+ using XDA Premium HD app
Click to expand...
Click to collapse
Apart from the the. Is that a BN at a point of too much geting on or it has to deal with the overal life of surge protection meh a chip?
ValentinD said:
Apart from the the. Is that a BN at a point of too much geting on or it has to deal with the overal life of surge protection meh a chip?
Click to expand...
Click to collapse
No, it is probably from running CM11. That has a history of bricking devices with the faulty emmc chip due to applying trim automatically.
Sent from my BN NookHD+ using XDA Premium HD app