[Q] Problem with olinex 1.4.0 Bootloader - Touch Diamond, MDA Compact IV General

Hello All,
I was following the guide here, and came across a problem when trying to use Unsigned-Hard-SPL-Diamond-OliNex, opened the ROMUpdateUtility.exe. Once I click Yes to running Bootloader.exe my device freezes, is there any way around this?
Thanks,
DevPump

Problem Resolved [Close Thread]
I was using the wrong HardSPL for me device.
Close Thread.

Having issue with the RUU
I've been trying to get the Tael ROM using the guide (here), but I needed to use the Hard SPL package to flash it.
I used the RUU from the HTC site (5.11 or something) before I found this site and ever since then, I can't flash Energy or any other ROM to the SD card or the actual drive of my HTC Fuze.
On to my problem.... Any time I try and use the RUU from OliNex, I either get Error 246 (Device Not Responding) or 262 (Update Error). I've done the bootloader thing (power + volume + soft reset), and nothing works. I've removed the SD and SIM card, like it said to. I've tried to trouble shoot from the original thread about TAEL and googling, but no luck.
Any help? I'd really like to flash different ROMs to my Fuze
TOTAL NEWB STATUS - soooo be easy please
**Edit/Revise**
Looked through the site and found the "Tutorial/How-to's/etc" thread (here) and downloaded all the different RUU's. Tried the one signed to OliNex, didn't work. Tried the other ones, nothing worked. Did it with &without the SD and SIM card. Still nothing.
When I run any of the RUU's and it runs the progress bar, it only runs on the computer and not my Fuze. Getting really frustrated with this... So far only able to run Android through SD card, and the battery life barely works on that (5 hours on idle). Hopefully I can get some help from somebody.

did you tried reset your phone?
press the reset button under stylus slot..
hope it helped..

Related

Error 246, 260 and 202

hey guys,
I'm freakin' out... I followed the instructions on trinityguides.info to upload the Hard-SPL. However, even though the Active Sync is working and the RUU seems to connect to the mobile and everything if going fine so far I get this bloody 246 and that *****y thingy of a mobile is going into the three colour mode... Ok, not a big deal. As I've read in the FAQ just start the RUU again and it should be cool... well, its not... now I get a 260. Nevertheless, I've not given up yet. I tried the installation again. This time without accepting the message on the mobile, after a while I get another error 202....
so please guys... where is the trick??? I read something about go into bootloader manually - I reckon that's the camera,power and hard reset button combo. When should I do this???
I also downloaded all three of this roms, 1.20, 1.30 and the other Macrofl or so....
I'm running XP SP2, Active Sync 4.5,
Mobile: HTC P3600, IPL-0.50, SPL-1.07.0000, WM5 German
Update via SD
Hi,
I had the same kind of problem just a few days ago... and I solved it simply using my SD memory. Using it, you bypass the pc (and the connection between the PDA and PC) and all this type of problems "connection-depending".
You can flash your PDA putting the rom image on the SDcard (how you should do, you can read here here )...
Ciao
Tompo
hey tompo,
thx for your help, but I still have problems. I formated my Sandisk 2GB ultra II SD card and copied the RUU_signed.nbh to the root of the SD. Then I renamed the file to TRINIMG.nbh and went manually to the bootloader. However, there was only a short flickering of a grey screen that said "loading", after that I was back in that three colour thingy.... crap.... what the hell am I doing wrong???
seems as i have though luck with that mobile....
Any more hints???
cheers
dee-fu said:
hey guys,
I'm freakin' out... I followed the instructions on trinityguides.info to upload the Hard-SPL. However, even though the Active Sync is working and the RUU seems to connect to the mobile and everything if going fine so far I get this bloody 246 and that *****y thingy of a mobile is going into the three colour mode... Ok, not a big deal. As I've read in the FAQ just start the RUU again and it should be cool... well, its not... now I get a 260. Nevertheless, I've not given up yet. I tried the installation again. This time without accepting the message on the mobile, after a while I get another error 202....
so please guys... where is the trick??? I read something about go into bootloader manually - I reckon that's the camera,power and hard reset button combo. When should I do this???
I also downloaded all three of this roms, 1.20, 1.30 and the other Macrofl or so....
I'm running XP SP2, Active Sync 4.5,
Mobile: HTC P3600, IPL-0.50, SPL-1.07.0000, WM5 German
Click to expand...
Click to collapse
Ok.....You wanna get to the 3 strip screen?
Make sure the battery has a 50% of its charge.
-Turn the device off.(DON´T HOOK IT UP TO THE COMPUTER YET) so it should be off and unplugged.
-Press and HOLD camera button + power button,now you should see the 3 strips,if so you can hook it up to the usb port.
Got it?
I don´t remember now if you have to follow this step first:
http://forum.xda-developers.com/showthread.php?t=293957
Like I said I´m not sure,but take a look.....if you brick the phone there´s a way to fix it.
See ya.
THX
thank you guys for the support,
however, the source of the prob was the SD card. Even though I formatted the SD in my laptop with FAT32 and no label, it seemed to me that the mobile couldn't access it. I've done it several times - didn't work. Finally, I thought lets format the thingy with the mobile itself - voila - it worked.... I dono if something with my card reader is wrong... the SD was working fine with tomtom and was accessible in both (laptop and mobile) without flaws. Only the bloody flashing didn't work as it should be.... well, I don't mind any more, may be its a solution for another desperate trinity user....
Cheers guys - I'm runnin' on WM6.1 now....*sweet*
hello could you please say how did you format with the trini, cuz I'm really new and unable to find that function.
I have exactly the same problems, but no external card reader
Many thx

Can't flash Kaiser HardSPL in any way???

Iv'e tryed to flash HardSPL to Kaiser... Downloaded various unlockers/flashers, even SD card solution... When trying to flash over usb with some Kaiser-HardSPL.exe - after entering tricolor mode and when progressbar appears it always stuck on 0%, and nothing happens... Update utility shows error (Rom update utility encountered communication error or smth.) and sugests me to do recovery. Tryed everything - SoftSpl1.56, Softspl1.93, SSpl-kais...
Other method i've tryed - SD card
Iv'e followed instructions, formatted card, copied those two files (http://forum.xda-developers.com/showthread.php?t=420683) to sd card, but after resetting Kaiser it only shows "Loading..." and hangs... no restart, nothing... just "loading..." on screen...
Bootloader menu shows following versions:
KAIS130
SPL-3.29.0000
CPLD-8
somehow... after trying another 1000 -th time... it just flashed...
Have exactly the same problem, tried all other solutions! any idea on what the last method was that worked?
When flashing via USB it will hang at 0% (and fail w/ 260 error on PC side) if the SD card is left in. I've made that mistake more than once.
Remember to remove SIM, too.
I don't have sd card and I've got the same problem...
Any ideas?
I have the same problem. I want to upgrade Hard SPL 3.24 to newer version. I always get 262 error. Also tried all possible ways (MicroSD uses FAT32, but I didn't formatted It, because I don't have SD adapter).
Sometimes It's shown that flashing complete, but HardSPL version still is the same.
Read you noobs
FOLLOW THE DIRECTIONS
http://forum.xda-developers.com/showthread.php?t=396922
latinohot, I'm doing all right...
EDIT:
I changed cable, and it went for the first time
Biker182 said:
latinohot, I'm doing all right...
EDIT:
I changed cable, and it went for the first time
Click to expand...
Click to collapse
good, also check the contact pins, sometimes they get bent.
hmmm...
i STILL can't get hardspl to work at all...just get stuck at 0%
sabzi43 said:
i STILL can't get hardspl to work at all...just get stuck at 0%
Click to expand...
Click to collapse
Are you using sspl to upgrade? sim and sd out? usb cable or sd flash? Do you already have a hspl and are just upgrading?
If you're on an original spl you must use sspl to do it.
If you're upgrading then you can use the kaisdiag file by cmonex and an sd.
aaaaahhhhh
WarByte said:
Are you using sspl to upgrade? sim and sd out? usb cable or sd flash? Do you already have a hspl and are just upgrading?
If you're on an original spl you must use sspl to do it.
If you're upgrading then you can use the kaisdiag file by cmonex and an sd.
Click to expand...
Click to collapse
I'm using usb to windows 7, sim and sd were out.
The thing is i've never done this before, but i am pretty sure i have it down...
I tried this I think 3 times then started to panic when after the recover from the freeze, i noticed things being weird, so i hard reset so i still have a functioning phone until i figure this out.
(it still has bugs it never had before :/)
ive downloaded numorous hardspls, all didnt work.
it's been one saaaaaaaaaaaad experience cuz i really want to make this happen and brag to my guy friends I FLASHED MY PHONE.
and get win 6.5, of course.
any help much appreciated!!!!!!!
sabzi43 said:
I'm using usb to windows 7, sim and sd were out.
The thing is i've never done this before, but i am pretty sure i have it down...
I tried this I think 3 times then started to panic when after the recover from the freeze, i noticed things being weird, so i hard reset so i still have a functioning phone until i figure this out.
(it still has bugs it never had before :/)
ive downloaded numorous hardspls, all didnt work.
it's been one saaaaaaaaaaaad experience cuz i really want to make this happen and brag to my guy friends I FLASHED MY PHONE.
and get win 6.5, of course.
any help much appreciated!!!!!!!
Click to expand...
Click to collapse
copy sspl.exe into your device and run it then you can flash with CustomRUU
to much better you are using ActiveSync on Windows XP
Thanks so much!!! i got it to work!!!! i actually used a jump spl instead, but i now am running win 6.5 on my kaiser!!!!!!! and i'm beyond stoked
THANKS Y'ALL!

error 00018003 TRINIMG.nbh - FAIL

I am trying to upgrade ROMS. I have the Ollipro boot loader - ALL OK, the Radio ROM I want, ALL OK. When I try to flash a ROM ([P3600i] Karmba_a v10.1 - Diamond [fixed].rar) or (cmE_0.9_beta.rar) or (n0610e_beta_m2d.7z) I get the above error. I am flashing by SD as I do not use Windoze on my PC. Radio's flash this way fine. Would this be the problem?
tchoklat
3600i
tchoklat said:
I am trying to upgrade ROMS. I have the Ollipro boot loader - ALL OK, the Radio ROM I want, ALL OK. When I try to flash a ROM ([P3600i] Karmba_a v10.1 - Diamond [fixed].rar) or (cmE_0.9_beta.rar) or (n0610e_beta_m2d.7z) I get the above error. I am flashing by SD as I do not use Windoze on my PC. Radio's flash this way fine. Would this be the problem?
tchoklat
3600i
Click to expand...
Click to collapse
Hey, i think you have bricked your trin. Read my post also! there is a solution for your problem by making gold card. Haven't luck yet, but i still tried to get my trin working again.
thekidz.rocks said:
Hey, i think you have bricked your trin. Read my post also! there is a solution for your problem by making gold card. Haven't luck yet, but i still tried to get my trin working again.
Click to expand...
Click to collapse
Not sure if my 3600i is bricked as I have the Olipro 3.6 Hard SPL and I can SD-flash any Radio ROM. It is just the ROM it self that fails with the error as mentioned in the topic. Any guidance appreciated!
tchoklat
Hi all,
Most definitely it is not bricked. Been there with my tinity.
On my pda only the WM5 could be installed without the error code (i only could install it from SD, because i have vista on my computer, and even with trying to follow others advice i didn't managed to flash from my computer)
and after something like 6 hours of hard searches and many tries here is my solution:
1.installed Olios's hardspl_120 (tried both 130 and DES):
first i booted om WM5, copied SSPL-TRIN.exe and the hard-spl nbh that i've renamed it to trinimg.nbh, and run SSPL-TRIN.exe, that will get you in the famous tricoloured screen (i don't know why it only installed the hard spl this way, if i try to manually enter the boot with power+camera+the stylus inserted in the reset it didn't installed and i end up with "Upgrade fail" after 1-2% or i got i restart during the flash upgrade).
2. installed the last radio Trinity_Radio-1.50.08.11
the same way like the hard-spl from SD card.
3. installed WM6 ROM
I've taken a WM6 rom (the first that i tried was Mary v3.7) and installed from SD card.
That was it.... success.
After i've managed to put a wm6 rom i've tried wm6.5 rom and worked and a couple of firmwares.
Hope this post will help in need trinity owners, because i was last night very desperate.....and i didn't found any answers, just tried and tried and...... and hope this solution will work for you too.
good luck!

Is it bricked? (Upgrade ROM error)

(I'm not 100% sure this is the correct forum, but since it is very ROM related it didn't feel all wrong to put it in here...)
Hi guys. After som serious flashing of cooked ROMs I decided for some unknown reason that I should try to restore a stock ROM. Now, being very tired as I was, i completely forgott that its probably a good idea to flash a new Stock ROM on the unit BEFORE flashing it with a signed SPL....so I just flashed the Signed SPL to the device. That in it self seem to have gone ok, because when I start the unit it say "SPL-1.15.0000". Problem is though that it also says "Upgrade ROM error, please try again"
Now, what should I do? Have tried put both signed and unsigned SPLs on the storage card and started up via the volume down/pwr button thingy, but that does not seem to do anything. I have also tried to attach the unit to a USB port when in tricolor mode ("USB" shows up on the screen) and tried the CustomRUU program. It finds the device and starts to "upgrade" (grey screen on the device with 0%) but then it just doesnt seem to get any further...
As the device was working fine with a custom ROM before I started all this, I suspect that the main problem proably is that I now have a Standard SPL with a cooked ROM, and that they collide sort of. I, as well as the Blackstone, is now stuck and I am all out of ideas what to do? Have also tried Hard and Soft resets, but that doesnt seem to change anything.
Help!
try removing the SD Card and put the phone into bootloader mode and re-flash the stock ROM! if this doesn't work ... still with the SD Card removed try flashing to USPL and flash the stock ROM again!
hope this helps
You can try USPL on your HD and flash a custom or stock ROM with it.
PapaDocta said:
try removing the SD Card and put the phone into bootloader mode and re-flash the stock ROM! if this doesn't work ... still with the SD Card removed try flashing to USPL and flash the stock ROM again!
hope this helps
Click to expand...
Click to collapse
Thanks for the feedback!
Just be be sure, "into bootloader mode" is when you start the device holding down volume down and powerkey until you see the tricolor screen? Then that is probably what I have tried to do for a while now without success (total success that is, I do get into the tricolored screen)). Or maybe I am doing something wrong, could you perhaps point to a detailed explaination besides the one in "HardSPL" thread?
USPL I havnt tried, will do that! Is it still so that trying to do USPL on Vista is asking for trouble?
I read somewhere that Stock ROMs should only be flashed from internal storage, not SD cards, is that true? If so, how do I go about accessing that storage now when it doesnt show up in the file explorer on my PC (PC recognizes it as USB device, "HTC Sync" but I get no file access to it).
improwise said:
Thanks for the feedback!
Just be be sure, "into bootloader mode" is when you start the device holding down volume down and powerkey until you see the tricolor screen? Then that is probably what I have tried to do for a while now without success. Or maybe I am doing something wrong, could you perhaps point to a detailed explaination besides the one in "HardSPL" thread?
USPL I havnt tried, will do that! Is it still so that trying to do USPL on Vista is asking for trouble?
Click to expand...
Click to collapse
just do uspl it will work
improwise said:
Thanks for the feedback!
Just be be sure, "into bootloader mode" is when you start the device holding down volume down and powerkey until you see the tricolor screen? Then that is probably what I have tried to do for a while now without success (total success that is, I do get into the tricolored screen)). Or maybe I am doing something wrong, could you perhaps point to a detailed explaination besides the one in "HardSPL" thread?
USPL I havnt tried, will do that! Is it still so that trying to do USPL on Vista is asking for trouble?
I read somewhere that Stock ROMs should only be flashed from internal storage, not SD cards, is that true? If so, how do I go about accessing that storage now when it doesnt show up in the file explorer on my PC (PC recognizes it as USB device, "HTC Sync" but I get no file access to it).
Click to expand...
Click to collapse
bootloader mode is when you power off the device and hold the volume button down and press power till you get the tricolor screen...
so here is what you need to do .
1. remove the sd card
2. go into the tricolor mode connect your device to the pc and make sure it says (USB) at the bottom
3. run the stock shipped exe from you pc
if that didn't work then you should try the USPL version.. and there is a guide if you are using vista.. i just tried and worked fine.. here it is
http://forum.xda-developers.com/showpost.php?p=3331078&postcount=153
and the reason i'm asking you to remove the sd card because if you have a rom (blacimg.nbh) it won't let you do anything it will try to flash from the sd card and right now you don't want to do that.
and you shouldn't put any rom into the internal storage of the phone..
PapaDocta said:
and you shouldn't put any rom into the internal storage of the phone..
Click to expand...
Click to collapse
What happens if you do that? will it try and flash over the flash? Proper *&@! it up?
nicelad_uk said:
What happens if you do that? will it try and flash over the flash? Proper *&@! it up?
Click to expand...
Click to collapse
i don't think anything would happen... the file will get deleted when you flash as the rest of the files in the internal memory
Thank you everyone! The USPL thing solved it, when I did it from a XP machine! The once bricked Blackstone is not alive an kicking again!
About USPL, I saw the workaround for Vista, but downgrading a few components to make it work just doesn't seem like a safe way to do it. And I cant help but to think that it might have unwanted side affects, ie affecting system stability. But maybe I am wrong?
Going back to shipped ROM without bricking?
Hi,
After reading this thread I am now a bit worried and, as a newbie, would appreciate maybe a "simple" answer to my question.
I''ve been experimenting with various cooked ROMs after following the guide in the WIKI for installing HardSPL and then putting the ROM file (BLACKIMG.nbh) on my SD card and installing it using the power on + volume down button method.
However, I now want to revert back to the original "shipped" ROM, which I have downloaded from the list of shipped ROMs via the WIKI (I downloaded the one which closely matched what was originally on my HD - as I didn't know how to backup the actual ROM on my HD at the time).
So, my question:
How should I put the downloaded original/shipped ROM:
RUU_BlackStone_HTC_WWE_1.14.405.3_Radio_52.49a.25.26_1.09.25.14_Ship.exe
into my HD without bricking it?! Do I just run it on my PC with ActiveSync enabled or do I need to do something to remove the HardSPL or something first?
Sorry if this has been answered previously but I get confused when a thread just makes loads of references to SPLthis and SPLthat etc.!
if you have the HardSPL already installed on your phone then you don't need to do anything more.. just connect your phone to the pc and let it sync (activesync enabled) and flash to any shipped rom you want by simply running the exe file..
PapaDocta said:
if you have the HardSPL already installed on your phone then you don't need to do anything more.. just connect your phone to the pc and let it sync (activesync enabled) and flash to any shipped rom you want by simply running the exe file..
Click to expand...
Click to collapse
Brilliant! Thanks for the simple answer Worked no problem!

[FIXED] SPL 1.54 / HSPL Problem

I think I've been a total idiot and messed up my HD. I hope there's a way to salvage the situation!
I was attempting to flash a 1.56 ROM so tried to downgrade to SPL 1.54; this was going along nicely until it encountered an error and tried to re-start the flash. Now the device is stuck on "Loading..." before begining the flashing process.
If I soft-reset the device, the SPL has changed to 1.54.0000 according to the Bootloader screen but it says "Upgrade ROM code error Please try again".
I've googled that error message and found a few hits but none of them presented a solution; just people asking this question.
Since that, I've tried to Hard-Reset but it brings me back to the same Bootloader error.
I've tried to flash a ROM but the device can't connect to Activesync to use the RUU_Wrapper and flashing via the BLACIMG.nbh on my SD card won't work either; it just goes back to the same Bootloader error screen and gets stuck on the "Loading..." again.
I've also tried to flash the new HSPL which is 1.56 capable but that suffers the same problem.
Anyone have any suggestions? Please? Never encountered anything like this in years of flashing my Blueangel and Tytn.
Full details from my bootloader screen:
RUUNBH
BLAC100 32M
SPL-1.54.0000
MicroP-Blackstone (LED) v6
Upgrade ROM code error
Please try again
Serial
Please use "Search" function before you posting a new thread.
http://forum.xda-developers.com/showthread.php?t=502167
That doesn't seem to be the same problem as the one I'm encountering. I found that thread via Google as I said I had searched in my post and flashing the stock HTC ROM that came with my device did nothing to solve the problem; 3 machines here, one running XP, one running Vista and one running 7 all fail to connect to the device to allow for any sort of flashing and flashing via an SD card does not provoke a response either.
--Edit--
Sorry - realised that my reply sounded a little stroppy! Blame it on the stress of having a possible brick on my hands! Thanks for the attempt to help but, like it says above, that solution hasn't worked for me
dom_mitchell1 said:
That doesn't seem to be the same problem as the one I'm encountering. I found that thread via Google as I said I had searched in my post and flashing the stock HTC ROM that came with my device did nothing to solve the problem; 3 machines here, one running XP, one running Vista and one running 7 all fail to connect to the device to allow for any sort of flashing and flashing via an SD card does not provoke a response either.
--Edit--
Sorry - realised that my reply sounded a little stroppy! Blame it on the stress of having a possible brick on my hands! Thanks for the attempt to help but, like it says above, that solution hasn't worked for me
Click to expand...
Click to collapse
Have you tried reading cRaCKwHoRe's guide for flashing 1.56 roms. Can be found in my signature. If you follow his steps, you should have no problems
dom_mitchell1 said:
That doesn't seem to be the same problem as the one I'm encountering. I found that thread via Google as I said I had searched in my post and flashing the stock HTC ROM that came with my device did nothing to solve the problem; 3 machines here, one running XP, one running Vista and one running 7 all fail to connect to the device to allow for any sort of flashing and flashing via an SD card does not provoke a response either.
--Edit--
Sorry - realised that my reply sounded a little stroppy! Blame it on the stress of having a possible brick on my hands! Thanks for the attempt to help but, like it says above, that solution hasn't worked for me
Click to expand...
Click to collapse
Hi, dom_mitchell1...did you manager to fix you HD ? I have encountered the "exact" same problem...I went from 1.56 to 1.54...and now I am stuck on the bootloader at "Loading...." If you have a fix...can you please let me know...and save my HD as well....thx
If you use USPL you will be able to flash everything you want.
Fallen Spartan said:
Have you tried reading cRaCKwHoRe's guide for flashing 1.56 roms. Can be found in my signature. If you follow his steps, you should have no problems
Click to expand...
Click to collapse
That's what I was following when things went wrong. Don't know what I did but during the downgrade process the flash "encountered an error" and had to restart....only it never did and just left me stuck in the bootloader with an error message.
It's fixed up now though and I'm running Dutty's shipped version quite happily. To fix it I tried different .msi packages from HTC and eventually one of them managed a successful flash. From there I was able to continue with cRaCKwHoRe's guide.
i had a similar problem i was upgrading to 1.56 so i to my thinking reverted to a stock rom them loaded 1.14 stock spl where my phone started showing the error screen i investigated and found that the stock rom id downlosded from the stock rom section must have been tampered with as the signarure was incommplete. so now the spl was reading 114000... as it was stuck in tri screen the data had loaded to my device it justxwasnt signed so wouldnt work i dowladed the appropriat 1.56 rom from htc which includdes the new 1.54spl started it and there i whent stock 1.56 rom with stock 1.54 spl. i than loaded olinexs new hspl im running vista so had to use the manual tool but othere than that installed ok.
i hope that helped in short as long as ur screen is reading a stock spl u can install an apropriat 1.56 rom from htc i belive the issue is caused by impropper signage of some stuff marked as stock here.

Categories

Resources