Database Develop

[Q] Restoring Captivate from AT&T World Phone Screen

Hey folks. I'm hoping to get through this in one piece, with one walkthrough.
I recently messed up in flashing a Rom to my Captivate. It cleared the phone of firmware and left me with the AT&T splash screen.
I bought a jig, and am now at the "Downloading..." screen and am trying to take this slowly to ensure a properly functioning phone (I've been without for two weeks now).
I've read through the sticky post [link]http://forum.xda-developers.com/showthread.php?t=884364[/link] and have most of the downloads. The Odin link is dead, and I don't have the proper version (I used a version I later found out was bad).
What I'm hoping for is to get someone to show me where the proper version of Odin is, and maybe give me a quick guide to doing this for a Rogers Galaxy S Captivate.
I hope I'm not coming off as lazy, but I tried this solo, and it went awry. Thanks for any help in advance.

This is the link for Odin. http://forum.xda-developers.com/showthread.php?t=731989
You want to Open Odin, then use the jig to put the phone in download mode, connect usb to your computer and wait until odin recognizes your phone. Click Start and sit back and wait. You should then be able to put whatever rom you want on the sd card and flash

Okay. I got the proper download, and used Odin. It reported success.
I haven't unplugged the phone from the computer yet, but it's also not showing as a drive on my computer. I'm at the stage where I'm supposed to root the phone after using Odin and before flashing.
Should I unplug the phone, or is that going to send me back to square one?

JavaMac said:
Okay. I got the proper download, and used Odin. It reported success.
I haven't unplugged the phone from the computer yet, but it's also not showing as a drive on my computer. I'm at the stage where I'm supposed to root the phone after using Odin and before flashing.
Should I unplug the phone, or is that going to send me back to square one?
Click to expand...
Click to collapse
If you used that Odin 1 click you will have the AT&T version, it will work but you will have the AT&T boot up screen. After it is finished your phone should reboot by itself. If it didn't try pulling the battery and then turn it back on.

Driver Installation Issue at Fault?
Okay, so I'm starting to wonder what's going on with the communication between my phone and my computer. I have the drivers, but when I try to install them (64 bit, for a dual-core, right?), it claims to fail.
I think maybe that this is the reason I can't get the computer to recognize the drive. Also, when plugged in last time, it said it failed to install drivers again. Even when the phone was operational, I had issues with that.
So . . . I'm wondering if maybe I solve that and the issue becomes seamless. Any thoughts on this would be appreciated, as it seems I'm stuck until I get the phone to register. Even Odin won't see it now, although I've already passed that step. F-Bomb.

Did you get the drivers right from samsung web site if not thats why they wont install i had same thing when i got my cappy.
I got drivers from.samsung.com installed em worked perfect sence. i kept the download saved had to install em a few times over the last 9 or so months. Only because of all the dam software hardware i run. Good luck
Sent from my GT-I9000 using XDA App

Just because it's a dual core processor in the computer doesn't mean you have a 64 bit OS.
You might want to know what version of windows you have...just a thought.

Okay . . . I can't seem to resolve this driver problem, nor can I move forward in the previous issue of getting my phone back to a functional state.
I can't imagine what I'm doing wrong that everyone else managed to avoid. Could I maybe request some one-on-one time with an experienced Rogers user? Just to recall the exact steps they took in order to successfully UNSCREW their phone.
Again, I appreciate all the help. Every post is making progress. I'm just frustrated at my ineptness with solid state installations.

I'm still not able to install the drivers or get my computer to register the phone as a drive. I did a bit more reading, but I've found nothing but different driver links. Has anyone else had this installation failure?

I have had driver problems before...try plugging up phone; on computer control panel, device managment , go to were it has device (just click then till se something about samsung) then uninstall drivers, next unplug phone, reinstall drivers that are on design gears (developer) thread for odin one click, next plug up phone sbf it will say new hardware and install drivers then see if that works... Ps if need to just pm me and I will get back to you to try and help
Sent from my SAMSUNG-SGH-I897 using XDA Premium App

A side note: I just tried it from my computer and the link if good and they work
Sent from my SAMSUNG-SGH-I897 using XDA Premium App

Try it again, however this time plug your USB cable into the USB port in the back of the computer.

Drivers were installed properly with Toolbox. Thanks for the help

[Q] Bricked And JIG is not helping

HI,
I am from INDIA, few months back I got a Samsung Captivate , Till now i tried FIREFLY and CM7 ROMs . The first time flash i did it with ODIN i guess i did it with a wrong firmware ,So was stuck with AT&T screen boot loop issue. Searching the forums and found JIG may help and so made a JIG (as i can't get one here) . and recovered my phone and flashed stock and then FIREFLY and 2 weeks back i flashed CM7 for getting Gingerbread and not likeing the UI of the ROM tried to switch back to stock and then customize on my own.
So When i tried flashing Stock the installation was success the screen stuck few moments on AT&T logo and i thought it would go off, But as i was very eager to get my phone online again i pulled of the battery to restart manually (Which i dont think was nice idea ) Now the screen remains black even i use the JIG to get into download mode. But the phone heats UP when i plug it for charging on computer or directly to switch
HELP NEEDED as i am very addicted to this PHONE

I have the same issue. I was tryint to load Cognition and it just gets stuck on the ATT screen but I haven't tried a jig yet. I was wondering if I can replace the files on the phone with good files that aren't corrupted and see if it boots up because droid explorere can still pick up the phone and so does Odin but when I do a master reset nothing happens.

@rajasekhar - Have you tried: Removing all parts (battery, sim, sd) let it sit for a few min (my preference is around 10 min to insure no residual power is left in the system) then hold the jig in place and putting the battery back in? Keeping the jig in place, so that as soon as the device gets power it is immediately seeing the jig, before it can try any other processes.
A bit difficult to do with hand made jigs I know. If you still getting nothing then your in for the worst and the phone need a JTAG or service center visit.
Tho it sounds a little odd that it could boot up to seeing the AT&T logo, but does not respond to the jig. Might even be a hardware problem.
@i3oots - Since you say your still getting PC response your safe to try and reflash it or just pick something different altogether. Tho you might wanna let ODIN settle and just sit there doing nothing for a few min, w/o then w/ the phone plugged in. Or learn about Heimdall and go that route.

Would I be able to flash it even though it get's stuck on the ATT screen? It won't go into download mode. I'll look on the forums how to flash it too. I'm a newb at this which is why I bricked it but everyone has to start somewhere lol.

rajasekhar19489 said:
HI,
I am from INDIA, few months back I got a Samsung Captivate , Till now i tried FIREFLY and CM7 ROMs . The first time flash i did it with ODIN i guess i did it with a wrong firmware ,So was stuck with AT&T screen boot loop issue. Searching the forums and found JIG may help and so made a JIG (as i can't get one here) . and recovered my phone and flashed stock and then FIREFLY and 2 weeks back i flashed CM7 for getting Gingerbread and not likeing the UI of the ROM tried to switch back to stock and then customize on my own.
So When i tried flashing Stock the installation was success the screen stuck few moments on AT&T logo and i thought it would go off, But as i was very eager to get my phone online again i pulled of the battery to restart manually (Which i dont think was nice idea ) Now the screen remains black even i use the JIG to get into download mode. But the phone heats UP when i plug it for charging on computer or directly to switch
HELP NEEDED as i am very addicted to this PHONE
Click to expand...
Click to collapse
You have probably Hard Bricked your phone. A JIG will not work to recover the phone. If the phone has any life at all, then the JIG will work. Else, u hard bricked it...you should never remove the usb cable when flashing bootloaders or odin or anything!
the only solution is to get a JTAG which can recover hard bricks OR you can go to a warranty store (don't know about india) and make up a sob story and have them replace it..

rajasekhar19489 said:
HI,
I am from INDIA, few months back I got a Samsung Captivate , Till now i tried FIREFLY and CM7 ROMs . The first time flash i did it with ODIN i guess i did it with a wrong firmware ,So was stuck with AT&T screen boot loop issue. Searching the forums and found JIG may help and so made a JIG (as i can't get one here) . and recovered my phone and flashed stock and then FIREFLY and 2 weeks back i flashed CM7 for getting Gingerbread and not likeing the UI of the ROM tried to switch back to stock and then customize on my own.
So When i tried flashing Stock the installation was success the screen stuck few moments on AT&T logo and i thought it would go off, But as i was very eager to get my phone online again i pulled of the battery to restart manually (Which i dont think was nice idea ) Now the screen remains black even i use the JIG to get into download mode. But the phone heats UP when i plug it for charging on computer or directly to switch
HELP NEEDED as i am very addicted to this PHONE
Click to expand...
Click to collapse
Does your computer recognize the phone? If odin is open, does the box turn yellow when you connect your phone? Make sure you have the right drivers. I think cm7 and captivate drivers are different. Keep trying with the jig. Just because you can't see anything on the screen doesn't mean the phone is dead.

i3oots said:
Would I be able to flash it even though it get's stuck on the ATT screen? It won't go into download mode. I'll look on the forums how to flash it too. I'm a newb at this which is why I bricked it but everyone has to start somewhere lol.
Click to expand...
Click to collapse
If your phone is booting up far enough to send out USB info for ODIN and other PC programs to see it, then your still in a workable condition. This also means you can still get into download mode, but since things arn't working properly it will be harder. Depending on which bootloaders your phone has will direct which methods you'll have to try out to get into download mode.
AFTER you've had a chance to look around the forum and self-educate on the different ways of getting into download mode. If your still having problems give us a lil more info of what you were running before the flash and to which version of Cog you were trying to flash.

Did anything worked for you, if not only a jtag can help you looks like u hard bricked the phone.

Hi guys
@DaNarki : Yea i tried that method to .
Thanx for ur suggestions guys .I really squeezed through xda for all possible ways of unbricking but no use. SO thought JTAG was the only option.But wanna know more about JTAG???????
Went for a samsung service centre they said they wont handle other country products of samsung. Just yesterday went to the local Cell phone Repair store , He said like he would try using a Ctool box they have for installin onto the rom directly. So i thought why not Give a shot to it ...
That store guy raised another question in me . Yesterday after giving it in the morning he said to call in the evening . I did so and he said the Phone is booting on the Ctool but it is sometimes throwing error . I dint get his intention in saying so . have to go to him today

bricked maybe not
I thought I was bricked also ...HARD BRICKED......no buttons no nothing ...tried odin on, phone plugged in, and hold down volume up and down and reinstall batt......nothing worked.......but this... it worked for me........ok first of all remember this will be a bit tricky because you will have to keep the volume keys pressed the whole time till you have download mode......should also have full batt......take out the sim and any flash cards you may have in the phone and the batt.....set the phone down and watch a couple hours of tv or try to brick your buddies phone so he can feel your pain...lol something.....ok now after your tv show has gone off turn on your computer and start up odin one click to stock.... put just the batt in the phone.....if your friend is still there you should try this with 100% batt.... use his phone to charge your batt.....any way put the batt in the phone....plug the usb cable into your computer......now for the tricky part .......press down the volume up and down now and do not let them go till the end of this and you should have download mode.......now plug in the usb to your phone IF YOU HAPPEN TO GET DL MODE HERE THEN GO AHEAD AND LET GO OF THE VOLUME BUTTONS AND FLASH YOUR PHONE ....if not... KEEP THE BUTTONS PRESSED.......now take the batt out of the phone.....keep them pressed......unplug your usb cable......keep them pressed.... restart odin...... keep them pressed....plug your usb cable back in.......keep them pressed... re-install the batt.....you should get download mode.......remember you have to keep them pressed... JUST... the volume up and down pressed through the whole process nothing else....This worked for me and I was dead bricked no nothing from any of the keys no nothing..... I DIDNT INVENT THIS METHOD I READ IT ON HERE SOMEWHERE AND CANT FIND IT AGAIN......It did work for me when nothing else did.....so if the person that posted it reads this THANK YOU...... ................................................. I hate to say this but I may have got the last two instructions backward you may have to put the batt in before plugging in the usb cable.......Like I said I cant find the original post
rajasekhar19489 said:
Hi guys
@DaNarki : Yea i tried that method to .
Thanx for ur suggestions guys .I really squeezed through xda for all possible ways of unbricking but no use. SO thought JTAG was the only option.But wanna know more about JTAG???????
Went for a samsung service centre they said they wont handle other country products of samsung. Just yesterday went to the local Cell phone Repair store , He said like he would try using a Ctool box they have for installin onto the rom directly. So i thought why not Give a shot to it ...
That store guy raised another question in me . Yesterday after giving it in the morning he said to call in the evening . I did so and he said the Phone is booting on the Ctool but it is sometimes throwing error . I dint get his intention in saying so . have to go to him today
Click to expand...
Click to collapse

rajasekhar19489 said:
Thanx for ur suggestions guys .I really squeezed through xda for all possible ways of unbricking but no use. SO thought JTAG was the only option.But wanna know more about JTAG???????
Click to expand...
Click to collapse
If you just wanna know a bit about the process ask this guy. He is pretty much the only person in the US (I know not all to useful to a person in India) that does JTAG for the cappy.
I can tell you this much, it requires a special device called a Riff box and it sends boot info directly to the chip on the main/mother board that is used for the booting process.
Somewhere I've seen a site that listed info of ppl around the world that will JTAG, but I can't seem to find it right now.

malebornin69 said:
I thought I was bricked also ...HARD BRICKED......no buttons no nothing ...tried odin on, phone plugged in, and hold down volume up and down and reinstall batt......nothing worked.......but this... it worked for me........ok first of all remember this will be a bit tricky because you will have to keep the volume keys pressed the whole time till you have download mode......should also have full batt......take out the sim and any flash cards you may have in the phone and the batt.....set the phone down and watch a couple hours of tv or try to brick your buddies phone so he can feel your pain...lol something.....ok now after your tv show has gone off turn on your computer and start up odin one click to stock.... put just the batt in the phone.....if your friend is still there you should try this with 100% batt.... use his phone to charge your batt.....any way put the batt in the phone....plug the usb cable into your computer......now for the tricky part .......press down the volume up and down now and do not let them go till the end of this and you should have download mode.......now plug in the usb to your phone IF YOU HAPPEN TO GET DL MODE HERE THEN GO AHEAD AND LET GO OF THE VOLUME BUTTONS AND FLASH YOUR PHONE ....if not... KEEP THE BUTTONS PRESSED.......now take the batt out of the phone.....keep them pressed......unplug your usb cable......keep them pressed.... restart odin...... keep them pressed....plug your usb cable back in.......keep them pressed... re-install the batt.....you should get download mode.......remember you have to keep them pressed... JUST... the volume up and down pressed through the whole process nothing else....This worked for me and I was dead bricked no nothing from any of the keys no nothing..... I DIDNT INVENT THIS METHOD I READ IT ON HERE SOMEWHERE AND CANT FIND IT AGAIN......It did work for me when nothing else did.....so if the person that posted it reads this THANK YOU......
Click to expand...
Click to collapse
Thanx MAN!!!!!! . it seems interesting method to try .. but i have to wait 12 hrs to get my phone back from the guy i gave to repair that. he said his chances of getting it fixed are 50-50 so i might as well prepare for your method to ..

DaNaRkI said:
Somewhere I've seen a site that listed info of ppl around the world that will JTAG, but I can't seem to find it right now.
Click to expand...
Click to collapse
Thanx DaNaRkI .. hmm well i would now again start digging the threads for seeing wat u have suggested ..

rajasekhar19489 said:
HI,
I am from INDIA, few months back I got a Samsung Captivate , Till now i tried FIREFLY and CM7 ROMs . The first time flash i did it with ODIN i guess i did it with a wrong firmware ,So was stuck with AT&T screen boot loop issue. Searching the forums and found JIG may help and so made a JIG (as i can't get one here) . and recovered my phone and flashed stock and then FIREFLY and 2 weeks back i flashed CM7 for getting Gingerbread and not likeing the UI of the ROM tried to switch back to stock and then customize on my own.
So When i tried flashing Stock the installation was success the screen stuck few moments on AT&T logo and i thought it would go off, But as i was very eager to get my phone online again i pulled of the battery to restart manually (Which i dont think was nice idea ) Now the screen remains black even i use the JIG to get into download mode. But the phone heats UP when i plug it for charging on computer or directly to switch
HELP NEEDED as i am very addicted to this PHONE
Click to expand...
Click to collapse
hello brother,,
u can find the Jig here in india... i also purchased... and it worked for me..
Download-Mode-USB-Jig
press thanx if it helps..

rajasekhar19489 said:
Thanx MAN!!!!!! . it seems interesting method to try .. but i have to wait 12 hrs to get my phone back from the guy i gave to repair that. he said his chances of getting it fixed are 50-50 so i might as well prepare for your method to ..
Click to expand...
Click to collapse
Hope it helps I wish I could find the original post again to thank the guy that told me how to do it. I had sent that phone back to att and the promptly sent it back and told me the water dammage sticker in the bat compartment was missing and they wanted to charge me 409 bucks for the phone ....long story short it was there when I sent it and I told them to go pound sand up their ass because I wasnt paying them that much and ended up paying 125 bucks for a paper weight.So that is when I decided to have it jtaged but figured I would give it one more shot before mailing it off. That was when I found the post from that person and low and behold it worked........................... I hate to say this but I may have got the last two instructions backward you may have to put the batt in before plugging in the usb cable.......Like I said I cat find the original post

malebornin69 said:
Hope it helps
Click to expand...
Click to collapse
Buddy tried it ... Thanx for that..But dint help . Now going for another options i mean in search for other options
But ppl help me with JTAG thing and its users(or developers) availability in india

Forgot to mention
I Missed to explain my flashing procedure i have done this time . Like I never tried flash a boot file along and so was reading some threads about boot loader variations between FROYO and GINGERBREAD so i tried flashing ablong with boot loader and then I got the stock gingerbread file i put the boot loader SBL in heimdall Firstboot loader path .And Boom the first reboot got stuck and i removed the battery and then again when i tried to restart the phone is dead
Thinking this might have where the whole thing went wrong and made the cell dead .

Captivate suddenly not detected by PC

ok first off I have searched and have yet to find a sollution. So if there is one please flame me and point me to it.
Problem : I have 2 computers, both win 7 x64 pro. my desktop does not detect any cell phone, my friends droid 1 or my samsung captivate..... Both have all the drivers installed. That is a small problem because i have a laptop that does ( DID)
Big problem : phone having problems, me flash captivate and flash fail ( i think i used odin 2.2 flasher which for some reason doesnt want to work, i tryed it a few times before... but anyways so I'm in download mode and now the computer wont detect my phone, just like my desktop, I get the UNKNOWN USB device or the usb device did not install correctly blah blah blah malfunction... SO now I'm able to get into DL mode but thats it.... so where is the fix for this? Please help . its so strange that no changes were made and it goes from having worked for months to not working at all suddenly...
Again neither odin v 2.1 or v 2.2 ( as in froyo and eclar) will detect phone nor will the hemdol program or what evs.... so i can not boot past download mode. Please help .

the answers are out there... itll just take a bit of reading... however sounds like there are program incompatibilities somewhere not allowing your drivers to install especially after you said drivers did not install blah blah. Also try changing usb ports when you plug it in and go through and check to make sure all you usb drivers and ports are functioning properly. Furthermore check to ensure your charging port isnt loose and or pins bent or broken same with your cable.

try this as well... says right click and run odin in admin etc.
http://forum.xda-developers.com/showthread.php?p=16936821#post16936821

xbadwolfx said:
try this as well... says right click and run odin in admin etc.
http://forum.xda-developers.com/showthread.php?p=16936821#post16936821
Click to expand...
Click to collapse
Also use XP service pack 2 mode. This helps also.

JJ133169 said:
ok first off I have searched and have yet to find a sollution. So if there is one please flame me and point me to it.
Problem : I have 2 computers, both win 7 x64 pro. my desktop does not detect any cell phone, my friends droid 1 or my samsung captivate..... Both have all the drivers installed. That is a small problem because i have a laptop that does ( DID)
Big problem : phone having problems, me flash captivate and flash fail ( i think i used odin 2.2 flasher which for some reason doesnt want to work, i tryed it a few times before... but anyways so I'm in download mode and now the computer wont detect my phone, just like my desktop, I get the UNKNOWN USB device or the usb device did not install correctly blah blah blah malfunction... SO now I'm able to get into DL mode but thats it.... so where is the fix for this? Please help . its so strange that no changes were made and it goes from having worked for months to not working at all suddenly...
Again neither odin v 2.1 or v 2.2 ( as in froyo and eclar) will detect phone nor will the hemdol program or what evs.... so i can not boot past download mode. Please help .
Click to expand...
Click to collapse
What rom are you on? CM7 MIUI?

Well huge problem... for some reason the phone wont charge now so now i cant even get in DL mode and before that i couldnt for the life of me no matter what i read find a fix for the USB issue. idk what the **** it is but its really annoying.... I was using OFFICAL 2.2 and was trying to reflash it and try it again or flash 2.1 because i was getting random restarts. then the flash failed for some reason first time ever I think ( i seriously have flashed about a dozen times since ive had my phone over 9 months, So i know alot and have read alot, have a jig and all that jazz) so i know what im doing... I just got my phone back from samsung about a month ago they fixed a random button pressing problem, and now the turning off on a Stock rom ( plus firefly prior, why i went back to stock) made me paranoid, plus i use it as a clock for work so i cant have it turn off randomly at all. So what am I to do? I possibly can use my friends battery for a bit or my womans... but im thinking maybe this has less to do with computer now and possibly that my phone fried or something that i should send it in to samsung for warranty repair...since obviously if it was restarting on a new 2.2 instalation obviously there were probably some problems...

I read a similar story of this randomly happening to another experienced user on google, and he sent it in to samsung and they just sent him a new phone... my AT&T warrianty is long gone on my refurb but i still got 3 months left with samsung... idk why it isnt even charging on wall outlet or computer...
what to do?

Did the phone go "dead" after a failed firmware flash? Or it literally just all of a sudden won't charge? If it was truly random then it's a hardware problem all the way and most likely an issue with the USB port or a trace routed through it. Only 2 lines control charging and the Captivate is notorious for a pretty solid port from my findings.

Well I left my phone in the wall for hours and I guess it does charge so its not completely dead. Now just the issue of reflashing stock on there... so getting the USB to work in my computer. I take it the USB in the phone isnt dead or the JIG wouldnt work... I just want to know if the Random shut off is hardware related or a bad flash / rom? Anyone know what has less problems? 2.1 or 2.2? I dont think my keyboard is in 2.1 so i dont think i could take it... but i just want a working phone with my gingerbread keyboard <3 I just dont want it to turn off on me...

and now randomly odin's will still not detect, but heimdol will, but it fails about 18% into factoryrfs or what evs. And Yes I have used it before and yes I am following all directions. WTF this is blowing my mind... and yes repartition is selected

Are you using an OEM Samsung Cable? Don't use knock off cable for anything more than charging...

just fyi if u rooted ur phone and samsung checks the programing to find out and trouble shoot it will void your warranty and youll have to pay for it... so um maybe try spending the 50 and go with a refurb thru insurance.

Yes I'm using stock cable...
ANd its not rooted, its not ANYTHING since there is no OS on the phone so no way to see anything to void anything...

now most things ( on different computers) will detect the phone and all odin and heimdol but they will both fail at the beginning of any flash... Its like nothing can be pushed through the phone.... ?

I have heard once hedimall is used on a computer it screws with odin and wont let it see ur phone
Sent from my Stock KH3/4 2.3.4 Captivate using the XDA Premium App!

b-eock said:
I have heard once hedimall is used on a computer it screws with odin and wont let it see ur phone
Sent from my Stock KH3/4 2.3.4 Captivate using the XDA Premium App!
Click to expand...
Click to collapse
It doesn't necessarily screw with it. Heimdall installs a custom WinLIB USB driver to operate with Samsung Composite USB devices. This driver is used for Samsung Download mode which ODIN doesn't recognize. To switch back to using ODIN, you just need to go into device manager and uninstall the device and be sure to DELETE DRIVER FOR THE DEVICE. Then just plug the phone back in when in DL mode and the Samsung driver will be re-installed. However, this is really beginning to sound more like a hardware problem. I emailed you back and would be happy to put a final diagnosis or repair on the devil phone.

[Q] Usb problem with my galaxy

So heres the thing.
I flashed some firmware on my phone (did it 100 times no problem) but i got fail in odin.
I said ok nothing is wrong i can fix it. but to my suprise Odin wont recognise my phone. I get a message that the Usb is unknown.
Now beacuse i reinstalled my drivers i think that the computer needs a first time plug of another galaxy s to install the driver from the phone is that correct? (Cause my phone can only go to download mode)
so all i need to do is to get another galaxy s plug it in and let the computer recognise it for the first time. and than use my broken phone phone and it will work?

what firmware was it ,if it was ics sometimes you lose usb connections and odin wont recoqnise the phone

TIGER 123 said:
what firmware was it ,if it was ics sometimes you lose usb connections and odin wont recoqnise the phone
Click to expand...
Click to collapse
@Topic started i have the same problem and have a similar thread.
as for tiger. . . does that mean ics users are screwed if that occurs to them?

http://forum.xda-developers.com/showthread.php?t=1431523
I used this one

Problem solved here. I hope this solution helps you
I've tried so much, seriously SO MUCH. At the end it turns out it was my usb cable. i ripped my old usb cable apart for making me go ape ****.
lesson? No matter how many times you install, change ports, etc. Always be sure to try a new usb cabel. If you don't have a second one, i'd suggest you go buy a second one, it's worth a try. The whole time it wasn't working it was my stupid usb cable, changed it and in an instance i was ready to roll.
Wish you good luck!

My Galaxy Note Is DEAD!!

Hi everybody, I searched everywhere for a solution but no luck
i love my note so much that if i couldnt fix it i think im gonna kill myself.
let me tell you the whole story, maybe you can revive my note again.
im a daily rom flasher, sometimes even 2 or 3 roms a day,
i wanted to flash ics stunner rom so i went into cwm recovery,flashed the zip file and wanted to format data\factory reset, but while the phone was formatting i accidently pressed the power button, the phone was stuck and didn't complete formatting, i took the battery out, put it back in and powered the phone, it was stuck at the bootscreen GTn7000 Galaxy Note.
I got into download mode and flashed a stock rom, but it was the same.
i downloaded and flashed other stock roms but it was stuck at the bootscreen.
then i wanted to flash a stock rom that came with a Pit file, i did everythig correctly, and Odin was stuck at the partition thing, for more than 15 minutes.
i unpluged the phone i pressed the power button, NOTHING!!
i officially bricked my phone which i worked so hard for months to get it.
i tried everything,even the jig thing, i couldn't buy so i had to make one.
maybe i did somethig wrong with the jig or maybe because i didnt solder it or the usb plug im using isnt working.
this may be relevant, i pluged the usb OTG in the phone and in the OTG was a bluetooth peice for computers, the piece had a light, and the light was ON.
Another thing that if i leave the battery in the phone for a while, the camera area in the back gets a little hot, my phone always did that meaning its still alive.
i may have written too much, forgive me but im really desperate.
Thanks in advance.

You probably end up going to Samsung. Pay €200 and get a new motherboard.
Good luck.
Sent from my CM9 GT-N7000 using XDA premium

hav0c said:
You probably end up going to Samsung. Pay €200 and get a new motherboard.
Good luck.
Sent from my CM9 GT-N7000 using XDA premium
Click to expand...
Click to collapse
WOW...
the problem is that i live in a fu**ed up country and we dont have samsung here.
all phones come without warranty and by smuggling from other countries

You mentioned killing yourself. Bro it's just a phone... Hang in there!!!
Sent from my GT-N7000 using Tapatalk 2

First thing donot flash Ics now untill you are craze about it.2nd donot use CWM as much as possible.Read this.
Ok to the problem now.Since you say it gets hot,it might be still alive.Remove the battery and insert it after 10 secs and insert the jig and after few secs press vol up button.Now connect the phone to computer and see if its detected if it does try flashing abyy's kernel.I dont know which kernel for sure.Somebody might help you.People were able to get into DL mode when there screen were not showing anything.

There are situations when your phone is working, but your screen is black.
Let's hope yours is one of those...Try this:
1. Don't flash Abyss. Download a stock GB Rom instead.
2. Charge your phone for a couple of hours. You need your battery for the
following steps.
3. After charging, take out your battery and wait 1 minute
4. Put it back in
5. Boot into Download mode (Volume Down+Home+Power) (you will see only black screen)
6. Count to 10
7. Press Volume Up
8. Count to 10
9. Start your PC Odin
10. Connect your phone to PC
11. Wait untill PC installs the necessary drivers
12. If all goes well, your PC Odin will flash the yellow light with COM info in it
13. Flash your stock GB Rom
If this doesn't work, you'll need to think of the ways of getting your phone JTagged or where to get a new motherboard.

Dude, if you have no way of repairing a bricked phone in your country then stay away from flashing custom ROMs!!!
Sent from my superior GT-N7000 using Tapatalk

Bro as u mentioned already that u flashed stock once...all root and cmw will be wiped... i would prefer going to samsung service center and tell them that u were updating your phone through kies and after the update completed ur phone stopped working... they will fix it for free... and act innocent
Edit::: dint see the other post where u mentioned that there is no samsung center at your place... in that case theres only one thing u can do... buy the motherboard and fix it urself.... sorry that ur beast is dead

izzmohamed said:
Hi everybody, I searched everywhere for a solution but no luck
i love my note so much that if i couldnt fix it i think im gonna kill myself.
let me tell you the whole story, maybe you can revive my note again.
im a daily rom flasher, sometimes even 2 or 3 roms a day,
i wanted to flash ics stunner rom so i went into cwm recovery,flashed the zip file and wanted to format data\factory reset, but while the phone was formatting i accidently pressed the power button, the phone was stuck and didn't complete formatting, i took the battery out, put it back in and powered the phone, it was stuck at the bootscreen GTn7000 Galaxy Note.
I got into download mode and flashed a stock rom, but it was the same.
i downloaded and flashed other stock roms but it was stuck at the bootscreen.
then i wanted to flash a stock rom that came with a Pit file, i did everythig correctly, and Odin was stuck at the partition thing, for more than 15 minutes.
i unpluged the phone i pressed the power button, NOTHING!!
i officially bricked my phone which i worked so hard for months to get it.
i tried everything,even the jig thing, i couldn't buy so i had to make one.
maybe i did somethig wrong with the jig or maybe because i didnt solder it or the usb plug im using isnt working.
this may be relevant, i pluged the usb OTG in the phone and in the OTG was a bluetooth peice for computers, the piece had a light, and the light was ON.
Another thing that if i leave the battery in the phone for a while, the camera area in the back gets a little hot, my phone always did that meaning its still alive.
i may have written too much, forgive me but im really desperate.
Thanks in advance.
Click to expand...
Click to collapse
Your phone is pretty much dead I'm afraid
Why didn't you bother to read stickies first?
It has been known for several weeks now that doing a wipe from CWM in a leaked recovery (I.e all ICS ROMs except cm9 official) will lead to a corrupted emmc drive ,thus a dead phone
And no ,you pressing the power button had nothing to do with it being stuck
The moment you hit wipe from ICS stunner's recovery your phone was dommed.
Anyway what's done is done ,now find an unofficial repair shop and replace your motherboard.
I hope this makes it clear ,and good luck to you.

izzmohamed said:
Hi everybody, I searched everywhere for a solution but no luck
Click to expand...
Click to collapse
Try this : http://forum.xda-developers.com/showthread.php?t=1257434
To force your phone into Download mode !

octavian90 said:
You mentioned killing yourself. Bro it's just a phone... Hang in there!!!
Sent from my GT-N7000 using Tapatalk 2
Click to expand...
Click to collapse
if you had gone through what i went through to get the phone, you would probably do the same.Thanks for the reply, any thing would help me right now.

vijai2011 said:
First thing donot flash Ics now untill you are craze about it.2nd donot use CWM as much as possible.Read this.
Ok to the problem now.Since you say it gets hot,it might be still alive.Remove the battery and insert it after 10 secs and insert the jig and after few secs press vol up button.Now connect the phone to computer and see if its detected if it does try flashing abyy's kernel.I dont know which kernel for sure.Somebody might help you.People were able to get into DL mode when there screen were not showing anything.
Click to expand...
Click to collapse
Thanks man, i will definitely try it right away.

mother board
mother board is gone due to kernel harm of ics leak
sorry
this is the fact...

chasmodo said:
There are situations when your phone is working, but your screen is black.
Let's hope yours is one of those...Try this:
1. Don't flash Abyss. Download a stock GB Rom instead.
2. Charge your phone for a couple of hours. You need your battery for the
following steps.
3. After charging, take out your battery and wait 1 minute
4. Put it back in
5. Boot into Download mode (Volume Down+Home+Power) (you will see only black screen)
6. Count to 10
7. Press Volume Up
8. Count to 10
9. Start your PC Odin
10. Connect your phone to PC
11. Wait untill PC installs the necessary drivers
12. If all goes well, your PC Odin will flash the yellow light with COM info in it
13. Flash your stock GB Rom
If this doesn't work, you'll need to think of the ways of getting your phone JTagged or where to get a new motherboard.
Click to expand...
Click to collapse
kvsandeepreddy said:
Bro as u mentioned already that u flashed stock once...all root and cmw will be wiped... i would prefer going to samsung service center and tell them that u were updating your phone through kies and after the update completed ur phone stopped working... they will fix it for free... and act innocent
Edit::: dint see the other post where u mentioned that there is no samsung center at your place... in that case theres only one thing u can do... buy the motherboard and fix it urself.... sorry that ur beast is dead
Click to expand...
Click to collapse
kvsandeepreddy said:
Bro as u mentioned already that u flashed stock once...all root and cmw will be wiped... i would prefer going to samsung service center and tell them that u were updating your phone through kies and after the update completed ur phone stopped working... they will fix it for free... and act innocent
Edit::: dint see the other post where u mentioned that there is no samsung center at your place... in that case theres only one thing u can do... buy the motherboard and fix it urself.... sorry that ur beast is dead
Click to expand...
Click to collapse
MR.change said:
Your phone is pretty much dead I'm afraid
Why didn't you bother to read stickies first?
It has been known for several weeks now that doing a wipe from CWM in a leaked recovery (I.e all ICS ROMs except cm9 official) will lead to a corrupted emmc drive ,thus a dead phone
And no ,you pressing the power button had nothing to do with it being stuck
The moment you hit wipe from ICS stunner's recovery your phone was dommed.
Anyway what's done is done ,now find an unofficial repair shop and replace your motherboard.
I hope this makes it clear ,and good luck to you.
Click to expand...
Click to collapse
pvillasuso said:
Try this : http://forum.xda-developers.com/showthread.php?t=1257434
To force your phone into Download mode !
Click to expand...
Click to collapse
You guys are awesome, im gonna do everything you said and get back with the results, fingers crossed.
I have a friend who's going to Dubai,UAE in a week or so. if nothing worked i'll send the phone with her to repair it at samsung,does anybody know if there's a samsung service center in Dubai and give me the location ?
i cant thank you enough,really appreciate all the help.

firasusman said:
mother board is gone due to kernel harm of ics leak
sorry
this is the fact...
Click to expand...
Click to collapse
OK, how much will it cost me ?
by the way i forgot to mention that before i bricked the note, it had a charging problem, saying voltage too high,charging stopped,and when the phone is turned off the battery icon keeps appearing and disapearing, could it be that the jig is not working because of that??

Try a different USB cable?
Sent from my SPH-D710 using XDA

izzmohamed said:
OK, how much will it cost me ?
by the way i forgot to mention that before i bricked the note, it had a charging problem, saying voltage too high,charging stopped,and when the phone is turned off the battery icon keeps appearing and disapearing, could it be that the jig is not working because of that??
Click to expand...
Click to collapse
You're not going to like this: I had to send my phone back to Samsung to get that fixed. Basically the charging port was shorting out, happens when stuff gets inside it (dirt, moisture, etc, from what I read). You could try cleaning it, but for me the port didn't break, it just acted like it was charging when there was nothing plugged in. So the JIG will work if it's supposed to.

jeffrey567 said:
Try a different USB cable?
Sent from my SPH-D710 using XDA
Click to expand...
Click to collapse
I did, still the same.
jayshah said:
You're not going to like this: I had to send my phone back to Samsung to get that fixed. Basically the charging port was shorting out, happens when stuff gets inside it (dirt, moisture, etc, from what I read). You could try cleaning it, but for me the port didn't break, it just acted like it was charging when there was nothing plugged in. So the JIG will work if it's supposed to.
Click to expand...
Click to collapse
Hmmm,i'll try cleaning it.I had the same situation, so the jig should work fine despite this problem ?

jayshah said:
You're not going to like this: I had to send my phone back to Samsung to get that fixed. Basically the charging port was shorting out, happens when stuff gets inside it (dirt, moisture, etc, from what I read). You could try cleaning it, but for me the port didn't break, it just acted like it was charging when there was nothing plugged in. So the JIG will work if it's supposed to.
Click to expand...
Click to collapse
Just out of curiosity: Are you in the US and had to send your international Note somewhere? I am wondering how one can get a support for an International Note if you're in the US.
I don't mind sending it to another country, but which Samsung center will accept it?

lanwarrior said:
Just out of curiosity: Are you in the US and had to send your international Note somewhere? I am wondering how one can get a support for an International Note if you're in the US.
I don't mind sending it to another country, but which Samsung center will accept it?
Click to expand...
Click to collapse
I am wondering the same thing, mine got bricked about a week ago and I don't really know what to do with it