was wanting to install serendipity 6.4 on my phone and like a dumb ass i left my phone in mass storage mode instead of usb debugging mode when i started odin, i pulled my battery and now i have the phone+computer image and canot get it into download mode, am i completely screwed and if not can anyone kindly guide me through what to do, its my first time rooting
odin uses download mode not debugging or mass storage...
dunno what you think you are talking about there...
installing serindipity has nothing to do with rooting.
rooting and installing roms are 2 different things.
you should have READ before touching your phone.
take out battery count to 5 put back in
hold both volume buttons,
plug in USB, KEEP BUTTONS HELD until you see BIG triangle
this is download mode.
go read instructions to fix yourself from here.
go read instructions go read instructions go read instructions go read instructions go read instructions go read instructions go read instructions go read instructions go read instructions go read instructions go read instructions go read instructions go read instructions go read instructions
are you getting the hint?
programming a phone (or anything) cannot be learned in 10 minutes
...i feel even more dumb now...thank you for your quick reply tho, once at this stage do i have to continue with the flash back to stock to be able to use my phone again?
that would be your best bet.
start from scratch
read then flash.
http://forum.xda-developers.com/showthread.php?t=731989
better luck next round
ok, does odin normally take a while to go back to stock? when i tried it earlier the progress bar never would move so after about 15 min i just pulled the plug
yeah odin can lock up... you dont have much of a choice but to unplug
were you using the one-click odin i linked you to?
or the other full odin flasher?
either way just try again....
i was using one click, how long should i wait before i unplug and try again?
5 minutes max...
click start not master clear...
master clear will wipe your SD card and wipe user apps and data, and must be done with the phone booted up normally and debugging on.
flash to stock from download mode.
what can i do if it continues not to work? and yea i know not to click master clear
run Odin as administrator...
just keep trying, or try another computer....
remember to install drivers...
ok, if worst comes to worst and odin just wont work no matter what i do, what do i do?
if you can get into donwload mode there is no reason you shouldnt be able to get back to stock...
but... how long have you had the phone?
there is 30 day instore replacement
or 1 year warranty exchange...
now if your phone all of a sudden *no longer turns on* and for some reason *will NEVER work again* they cant prove you voided your warranty... and will fix it.
think speaker magnets or a short 1 or 2 second burst in the mic. dont want physical damage but you want it to stop working. FOREVER.
then play dumb... " i dunno just stopped working... "
got it for christmas, and yea i can get it into download mode, would trying the odin that flashes back to 2.2 be worth a shot or do i have to use the 2.1 one that you linked me?
well the 2.2 one click is a beta 2.2... and has 3e recovery... theres plenty of fixes for 3e though.
im trying to find another odin for you...
alright thank you
removed.....
nvm it is 1010, so just follow that and i will be at full stock and from there i can go ahead and flash serendipity?
wait... im looking for something better... damn americans... i have all my links bookmarked... lol
I FOUND WHAT I WAS LOOKING FOR!!!
http://forum.xda-developers.com/showthread.php?t=995143
alright thank you very much just one last question for ya, when i do this if i decide not to go to a custom rom can i use the kies program and upgrade back to 2.2?
Related
Hi was gonna flash new firmware with odin since froyo was delayed 1month + more..
Now it wont turn on, is there any any any thing i can try to do to save my phone????
Remove the battery, wait 10 seconds, replace the battery, restart into download mode, reflash
Got into download mode, but i cant reflash, it says failed.
Which Firmware are you trying to flash, what options did you tick (repartition?)
If download mode works you are good. Reboot your PC, make sure Kies is not running. Try to flash to some knownly good ROM (JM2/JM7/JM8) - follow the corresponding instructions here in the posts to the letter. Make sure you use correct Odin version (not AT&T).
When i crashed the firmware i was using repartition tried install jm8
Ok will reboot comp do all this, brb like 5 min and ill let you know, Really Really gratefull for all helps
And there i got it working , thanks for making me calm saying it would work out when i was freaking out, 900$ is allot to loose ^^
And the reason i crashed it was that i didn follow the guide completely after reset came i waited a while , didn know it took that long for Pass so i unplugged to early, lesson learned and hopefully my sgs wont die by my hands
I was at 2.1.1 Cognition and for some stupid reason went into ROM manager and tried to apply my original backup I did when I was just Rooted and on the stock software from ATT.
It got to the data partion and couldnt access it, rebooted and now I get force close errors when it boots. I can virtually do nothing cause the errors just come one after another.
I tried to go into download mode so I could use ODIN and start over and it will NOT go in download mode. I am holding the vol up and down and then pressing power. I am holding all three until the screen goes black twice then letting go of the power. It just goes back to the little circle in the middle meaning its charging.
I am hosed....please help me get this fixed!
The force closes comes from within android...its boots up but is unusable.
gocats7 said:
I was at 2.1.1 Cognition and for some stupid reason went into ROM manager and tried to apply my original backup I did when I was just Rooted and on the stock software from ATT.
It got to the data partion and couldnt access it, rebooted and now I get force close errors when it boots. I can virtually do nothing cause the errors just come one after another.
I tried to go into download mode so I could use ODIN and start over and it will NOT go in download mode. I am holding the vol up and down and then pressing power. I am holding all three until the screen goes black twice then letting go of the power. It just goes back to the little circle in the middle meaning its charging.
I am hosed....please help me get this fixed!
Click to expand...
Click to collapse
First of all, for God's sake please post on the RIGHT AREA. This is not develpoment....the mods are tired of saying the same thing and I dont see why is this so hard to understand.
Turn the phone off then Hold Vol Up and Down then plug the usb while holding those.
That is the way mine goes into download mode.
My bad, feel free to move it.
As I posted, I am doing that and cant get into download mode....please help and again sorry for posting to the wrong area. Im kinda freaking out.
Appologies again, I didnt read your post well.
I tried it the way you stated as well and it goes to the charging screen only.
When I post in the future I will pay more attention to where I post, I understand the frustration.
I cant go into recovery or download either one. Am I bricked? I could really, really use some help. I know I screwed it up and it was a great lession...I just dont want it to be a costly one.
1st question - were you able to get into either download mode or recovery mode via the button combos before you installed cognition?
2nd - if you let it boot up will it boot all the way to the lock screen?
1) Yes I was able to get into download mode and recovery mode before I screwed up.
2) Yes, I can get all the way to the lock screen and if i catch it just right I can navigate the os but it is almost impossible.
The backup from within ROM Manager I applied was back to the original OS that came on the phone that was rooted and had rom manager on it.
I would bet that whatever files allow you to get into download mode, etc are gone or something along those lines.
I am about to freak out.
have you tried pulling your battery, sim card, and any external sd card, let the phone set for a minute, then put back only the battery and then try either the recovery or download button combo?
I am able to get all the way to about phone and here is what it says. I have a combination of mess....man I screwed up royally.
Build Number
ECLAIR
Kernel Verson
2.6.29
[email protected] #237
BaseBand Version
I897UCJH7
Firmware Version
2.1 -Update 1
Again, I was on 2.1.2 Cognition and went through ROM manager and applied a backup which was a snapshot of my phone the day I got it, rooted it, and added ROM Manager. Which isnt there now.
I know what I did was really stupid, I know what I should have done. I would just really appreciate any help getting this back or getting it to a point that I could send it back and not get charged for it. I got it from amazon. Do you even think they would look at the file system? I am within my 30 day window.
Yes, it boots up normally meaning not into download or recovery mode. The specific errors I am getting in the os are as follows:
The process android.process.media has stopped unexpectedly and i have to click force close. I do get a few others about browser, phone, gallery, calendar, but in the end the media one is the one that comes up over and over. Since I can get this far surely there is a way to get me back to a workable state that I can fix it.
If not, I wonder if I could connect via usb and try to wipe every file off the darn thing and send it back? Obviously I would like to avoid that but I am running out of options and frankly this is over my head.
I dont think your trying the download mode correctly with the battery out. You need to take your battery out, put the battery back into the phone, hold down BOTH the volume up and down keys at the same time by pushing in the middle of the keys and then plug the usb into your phone. This works every time.
I can get into the phones Hard drive via USB and see the folders. I see .img files within clockwork that were suppose to have applied, not that it it matters.
I wonder if I could delete anything that isnt part of the stock image and send it back and just not be an idiot again? I really dont want to do that but I dont know what to do.
I found this log file on the device and the last line was the error that I got right before it rebooted and I was hosed:
Can't mount /data/!
Failure at line 2:
restore_rom /sdcard/clockworkmod/backup/original boot system data cache sd-ext
aNdroidnut I tried it exactly as described and all I get is the lines in a circle stating that its charging then the battery charging. I have tired it the way you said and the way I had done it all the other times.
I think the problem is i have an incomplete OS since it failed in the restore process within ROM Manager because I never should have done it that way.
If you were able to get into download via button combo before you should be able to do it now with after pulling your battery, sim card and external sd card as I mentioned before.
gocats7 said:
I can get into the phones Hard drive via USB and see the folders. I see .img files within clockwork that were suppose to have applied, not that it it matters.
I wonder if I could delete anything that isnt part of the stock image and send it back and just not be an idiot again? I really dont want to do that but I dont know what to do.
Click to expand...
Click to collapse
If you can get to this point you are not bricked and can recover. I am guessing you are connected to your computer in usb debuggin mode -- this is good as there is another way to get into download mode.
use oden3 one click here http://forum.xda-developers.com/showthread.php?t=731989
use download method one in the odin3 instructions if you can get connected to your computer in usb debugging mode. use download method 3 if you can get into download mode via the button combo after a battery pull
i think you failed at reading the warning:
disable the lagfix before trying to use clockwork
Are you trying this with Odin already open?
Sent from my SAMSUNG-SGH-I897 using XDA App
When I try what everybody else explains I too just go back to the loading circle. Then it just goes right back to my charging screen. I figured this method out by mere chance one night when tinkering. I haven't seen it posted anywhere, so hopefully this is what you need:
1) open odin
2) pull battery, sdcard, and sim card
3) plugin usb to phone and computer(NO BATTERY YET)
4) hold down vol up and vol down(NO POWER BUTTON)
5) place battery into the phone
This works every time for me no exceptions.
Hope this helps,
S4NDM4NN
OK, I have made progress thanks to the great tools these guys have and your help!
I am shaking as I type this (yea i know its just a phone). I was able via Odin to do a master clear. It rebooted and now I get into the OS and get NO errors. It seems fine but will not go into download mode no matter what I do and I have gone into it many times in the past. I went from stock (via Odin) to Cognition several times initially to really understand the process. I never had problems getting into download or recovery.
I really think, with you guys help, Im going to be ok here. I saw where you wanted me to do method 3. I have tried method 3 many times and method 2 many times.
Since I am able to get it to boot error free I was considering unrooting, rooting, downloading ROM Manager and trying to put Cognition 2.1.2 on it via Rom Manager. BUT before I do that I want advice if you would. Obviously following what I thought got me to this point to start with.
Fixing so-called "Bricks"/Odin Errors
This guide is open to contribution/editing/correcting
I DO REALIZE THAT MOST OF THESE LINKS ARE BROKEN, PLEASE SCAN THE THREAD TO FIND UPDATED LINK. I'M NOT VERY ACTIVE ANYMORE, SORRY!
-----------------------------------------------------------------------------------------------------
BOOT CYCLE
This is where you get the annoying Samsung Screen/Galaxy S screen.
DOWNLOAD REQUIRED (CREDITS TO Woodrube):
JFD ODIN Images from Samsung (PDA)
Stock JFD Image
512 PIT File (PIT Extract first!)
Stock 512Pit
ODIN
Odin3_v1.0.exe.zip
Click to expand...
Click to collapse
1. Get into Download Mode (WITH THE PHONE PLUGGED IN) by following the steps below
*Turn off the phone until you get to the charging battery screen (keep in mind, your phone is currently PLUGGED IN)
*Press volume up and down, and power all at once.
*As soon as the screen turns black, release your power button.
2. Unplug phone from USB
3. Open Odin (in Administrator if you're running W7 or Vista), try one of the ones I attached to this post, at least one of them is bound to work, some don't work for me, but works for others, some doesn't work for others, but works for me, whatever floats your boat
4. Load in the files into Odin that you have downloaded from above Just load in the files corresponding to the text field.
DO NOT CHECK REPARTITION.
5. Plug in your phone with the DL mode
6. Click start and wait for the magic
-----------------------------------------------------------------------------------------------------
NO-BOOT PHONES
This is where your phone does NOT turn on, no combo of buttons works and power button does nothing.
DO THIS ONLY WHEN YOU PLUG IN YOUR PHONE AND NOTHING SHOWS UP ON THE SCREEN!!! If else, follow the steps from above.
This method is basically same as above, EXCEPT the way you get into Download Mode as your phone is HARD BROKEN.
1. Download all the files required in the "BOOT CYCLE" section of this post.
2. Remove everything from your phone (SD card, sim, battery).
3. Plug your phone into your computer WITHOUT the battery, as you have already taken it out in the last step.
4. Press and HOLD vol. up and vol. down.
5. As you are HOLDING these buttons, reattach your battery.
6. You should be in Download Mode.
7. Unplug phone from USB
8. Follow steps 4-8 from the "BOOT CYCLE" section.
Troubleshooting:
-Odin stuck at some random process?
*Switch to another odin
*Make sure you did NOT check repartition, if you did, just repeat all the steps over again, except for the downloading parts, obviously.
-Phone not responsive?
*Try "NO-BOOT PHONES"section of this guide
-Phone stuck at Galaxy S logo screen?
*Put it in to DL mode, and run Odin again, it's just a bad install.
-All three ODIN is nonfunctional, stuck or giving "FAILED" errors?
*DO NOT CLOSE ODIN ONCE IT HAS FAILED!
*Unplug your phone
*Replug in your phone, get it into DL mode
* Unplug once it is in DL mode
*Replug and ODIN should recognize your phone
*Leave all the settings the same, then click "Start" again.
-Cannot get into download mode using the method I listed? Use the method(s) below:
Soldering Method
More methods coming soon
-----------------------------------------------------------------------------------------------------
I know how much of a pain posting in the Q/A section can be and the wait time is pretty bad, so if you need help regarding UNBRICKING and ONLY UNBRICKING feel free to post in here.
Hope you enjoy, this is my first guide, please don't flame. Any comments or suggestion is suggest, or if you have your own method I'll also post it
POST YOUR RESULTS!
-Steven
The only forums this guide should be posted on is XDA, DZ, and PHANDROID under the username DRAIKZ and EXPLOSIVE. If it helped you, feel free to donate a coke or two!
​
Nice Guide! One thing I noticed is that the color is overdone and instead of helping with reading it has the opposite effect. Made everything look semi-messy and crowded.
good guide..
one question though, the PIT file is the one for the Tmobile JFD file. would that affect any unlocked vibrant? I mean, would it lock the phone back to Tmo??
thanks for sharing,
Cheers
I thought there's no fix to a phone which is really BRICKED? oh well, everything's possible at this time.
Please be more descriptive in your terms of "brick(ed)". The term bricked is meant that your phone isb rendered COMPLETELY & UTTERLY USELESS, FOREVER! The phone will never get used again... Hence.... Brick!?
I like the guide just think it would better off with more descriptive details of what caused the phone to boot loop or not boot.
Ok let me fix up the terms when I get home. I don't think you can ever make the vibrant utterly useless haha. Android phones are nearly impossible to brick
Sent from my SGH-T959 using XDA App
angel6677 said:
good guide..
one question though, the PIT file is the one for the Tmobile JFD file. would that affect any unlocked vibrant? I mean, would it lock the phone back to Tmo??
thanks for sharing,
Cheers
Click to expand...
Click to collapse
I'm not too sure as I do not have an unlocked phone myself and was wrong the same thing a few days back.
Sent from my SGH-T959 using XDA App
Is there a fix for the brick where the phone does not turn on at all amd does not even respond to the usb in the phone like for example plugging in the phone a wall charger and not even a grey battery or a little circle symbol?
Sent from my SGH-T959 using XDA App
Yeah, read the info under the "HARD BRICK" section Good luck, it should work as that also happened to me, I had it fixed with the method I listed up there.
If you need help or some questions answered during the process, I'll be online for another hour or so, or just PM me
OP. Can you add the soldering option as well? Would be good to have it in here. Added this Guide to the WIKI.
swehes said:
OP. Can you add the soldering option as well? Would be good to have it in here. Added this Guide to the WIKI.
Click to expand...
Click to collapse
Will do and thanks for the add
Now off to find the soldering guide x]
what do you do when you use odin and it STILL boots back to the samsung screen??
If the black screen doesn't change after like 15 minutes, then just do the whole process all over again. It could just mean a bad install
Even programs messes up sometimes
Goodluck!
Remember, please post your results so I can see how I can improve this guide!
So, i think i have actualy made a brick. I was running macnut r12/a13 kernal for about a week and had some issues with the overclock so i figured i would just flash aver itself as that has fixed a few issues in the past. booted into clockwork, flashed the rom, no worries. Hit reboot system and it hung at the vibrant/i9k boot screen. At this point i was still not worried. Here is where it gets fun. My Phone will now not boot into recovery, i have been trying now for about 4 hours. I can boot into download mode, but i can not get odin to see my phone. On the same PC, odin sees other vibrants, just not mine. If i turn on the phone it just boot loops at the vibrant/i9k screen. My pc makes the usb plug/unplug noise as it boot loops turning on and off with the vibrant/i9k screen telling me that the drivers could not be installed. If i plug my gf's vibrant in, i have no issues and odin gives me a com port. Any suggestions?
THANKS dude only if if you posted this before when my vibrant was soft bricked... I sent it back I didn't know what to do hehe!
Also a question... if I do this.. will it remove root and everything also does my phone HAVE to be soft/hard bricked to use these methods because I might want to just use the soft brick Odin thing when I want to get back to normal without being soft bricked...
Sent from my SGH-T959 using XDA App
@ Adam, have you tried installing the drivers manually? If not, then I don't know what to say =/ But I'm SURE people around here can offer some help
@Rider, You're welcome, and yes it does remove everything, and yes it does work even when you're not stuck in bootloops
draikz said:
@ Adam, have you tried installing the drivers manually? If not, then I don't know what to say =/ But I'm SURE people around here can offer some help
thanks for your reply
If odin recognizes one vibrant( the working one, my gf's) and not the other(my bootlooping) do you still think its a driver issue.
Macnut is a amalgam of almost all the galaxy s's. when my phone booted it would startsaying vibrant, then flash i9k. i did install kies thinking it would have some drivers for the i9k. I will try monkeying with the drivers a bit and let you know.
Click to expand...
Click to collapse
Ok, try playing around with the USB cable, trying different USB ports, too.
No problem, remember to post your results once you try it
Hello. I have searched the forums and have not really found out an answer to my question. Earlier in the week I tried installing Andromeda with an ursa minor kernal I believe? (I was following a tut on youtube) I succesfully got ursa minor on my phone but the tutorial failed to mention I had to put Andromeda on the internal sd card to flash it. (first time trying to flash a rom so big noob). I decided to go back to stock and retry using Odin One Click. Odin bricked my phone because it is build number 1108 :/ I have an infinite ATT world phone boot loop because of this. I will be trying to make a jig/buying one soon to get back into download mode to fix this. I am not sure exactly what I am supposed to do once I am in download mode. I want to get back to stock. Obviously Odin One Click doesn't work because of my build number. What steps should I follow to go back to froyo 2.2 and to retry? Please help I am just not sure.
yakobo said:
Hello. I have searched the forums and have not really found out an answer to my question. Earlier in the week I tried installing Andromeda with an ursa minor kernal I believe? (I was following a tut on youtube) I succesfully got ursa minor on my phone but the tutorial failed to mention I had to put Andromeda on the internal sd card to flash it. (first time trying to flash a rom so big noob). I decided to go back to stock and retry using Odin One Click. Odin bricked my phone because it is build number 1108 :/ I have an infinite ATT world phone boot loop because of this. I will be trying to make a jig/buying one soon to get back into download mode to fix this. I am not sure exactly what I am supposed to do once I am in download mode. I want to get back to stock. Obviously Odin One Click doesn't work because of my build number. What steps should I follow to go back to froyo 2.2 and to retry? Please help I am just not sure.
Click to expand...
Click to collapse
You'll have to use the full Odin program and grab a stock ROM from the development section. Once your in download flash stock ROM with through Odin or heimdall. I'm not next to my computer so I don't feel like fishing for links ..but should be fairly easy!
Sent from my SGH-I897 using xda premium
yakobo said:
Hello. I have searched the forums and have not really found out an answer to my question. Earlier in the week I tried installing Andromeda with an ursa minor kernal I believe? (I was following a tut on youtube) I succesfully got ursa minor on my phone but the tutorial failed to mention I had to put Andromeda on the internal sd card to flash it. (first time trying to flash a rom so big noob). I decided to go back to stock and retry using Odin One Click. Odin bricked my phone because it is build number 1108 :/ I have an infinite ATT world phone boot loop because of this. I will be trying to make a jig/buying one soon to get back into download mode to fix this. I am not sure exactly what I am supposed to do once I am in download mode. I want to get back to stock. Obviously Odin One Click doesn't work because of my build number. What steps should I follow to go back to froyo 2.2 and to retry? Please help I am just not sure.
Click to expand...
Click to collapse
This is a Odin 1 click for KB1 2.2 stock. After that follow any roms instructions except if it says stock 2.1 ignore it and assume its stock 2.2
I was wondering if I should follow this thread??
http://forum.xda-developers.com/showpost.php?p=10056254&postcount=36
Might I ask do you need to get to 2.1?
prbassplayer said:
Might I ask do you need to get to 2.1?
Click to expand...
Click to collapse
When I got my phone (about a two weeks ago) it came with 2.2 already on the phone. I don't need to get to 2.1 but I was thinking I'd go to 2.1 and then upgrade to 2.2 using att? If I can?
But why? If you got it as is and its stock its att's 2.2. At any rate If your so inclined on flashing 2.1 the one you mentioned thats using full Odin with pit should work. I suggest doing it if and only if you have that jig handy. Also keep in mind that .tar probably has bootloaders in it (wich is a risk you really dont need to take) just my 2 cents
prbassplayer said:
This is a Odin 1 click for KB1 2.2 stock. After that follow any roms instructions except if it says stock 2.1 ignore it and assume its stock 2.2
Click to expand...
Click to collapse
Links in that thread seem to be broken:/ So I suppose I can't use that.
Ive never used this one but it is also a KB1 2.2 KB1
My ultimate goal is to get Andromeda3 on my cappy. It seems to be a good rom. Could I just flash that using oden? (put it in the pda slot) or will that not work until I go back to stock?
With this new thread you linked me to, Just put in odin and I should be good to go? Thank you for your help by the way.
Ive never used that rom. Follow their instructions and assume stock is 2.2 for you. Also The original link i sent you should have worked. Aperrantly mediafire.com is having issues tonight.
installing Andromeda3 doesnt require going back to stock, 2.2 or 2.1.
ODIN flash a custom CWM kernel
boot to recovery
flash rom
thats it
Pirateghost said:
installing Andromeda3 doesnt require going back to stock, 2.2 or 2.1.
ODIN flash a custom CWM kernel
boot to recovery
flash rom
thats it
Click to expand...
Click to collapse
I can't because I bricked my cappy. i can't go into recovery right now. I need a jig to get back into download mode to fix it.
prbassplayer said:
Ive never used that rom. Follow their instructions and assume stock is 2.2 for you. Also The original link i sent you should have worked. Aperrantly mediafire.com is having issues tonight.
Click to expand...
Click to collapse
Once I get my jig hopefully mediafire is up and I can download from the first link you sent me. That seems to be my best bet right now. Thank you for your help. I sure hope I can get my phone backXD
yakobo said:
I can't because I bricked my cappy. i can't go into recovery right now. I need a jig to get back into download mode to fix it.
Click to expand...
Click to collapse
you are stuck in a boot loop right?
if you power your phone off, hold down both vol buttons and hold down the power button until the ATT screen comes up, let go, does it not go into recovery mode?
or
download mode:
power off, while holding both vol buttons, plug in usb. does that not work?
yakobo said:
My ultimate goal is to get Andromeda3 on my cappy. It seems to be a good rom. Could I just flash that using oden? (put it in the pda slot) or will that not work until I go back to stock?
With this new thread you linked me to, Just put in odin and I should be good to go? Thank you for your help by the way.
Click to expand...
Click to collapse
Get ursa minor back on your phone, then mount usb in mounts and storage, then copy the Andromeda3 zip to the drive. You were almost there.
Fish around in the usb port with 301kOhms of resistance from radio shack. You will hit pins 4 abd 5 and you will be in download mode.
Pirateghost said:
you are stuck in a boot loop right?
if you power your phone off, hold down both vol buttons and hold down the power button until the ATT screen comes up, let go, does it not go into recovery mode?
or
download mode:
power off, while holding both vol buttons, plug in usb. does that not work?
Click to expand...
Click to collapse
No:/ no button combos work to get me in recovery or download mode. Getting a jig (hopefully today) so I can fix all this. Yes it is in a boot loop
AdamOutler said:
Get ursa minor back on your phone, then mount usb in mounts and storage, then copy the Andromeda3 zip to the drive. You were almost there.
Fish around in the usb port with 301kOhms of resistance from radio shack. You will hit pins 4 abd 5 and you will be in download mode.
Click to expand...
Click to collapse
Thanks. I tried putting the Andromeda on the phone by copying it over to the phone through the mounted sd card but it was all of a sudden "write protected" and showed up as a cd instead of an sd card. :/ I know I was real close but I made some mistakes along the way
also, when you say fish around the usb port. you mean inside the phone? Is there any danger of hitting the wrong pins and possibly hurting my phone? (say i hit pins 3 and 5 by mistake or something) or is it all pretty safe? I was going to try and attempt the jig method that only used the resistors but n oticed the pins were horrible small in the phone:/
yakobo said:
Thanks. I tried putting the Andromeda on the phone by copying it over to the phone through the mounted sd card but it was all of a sudden "write protected" and showed up as a cd instead of an sd card. :/ I know I was real close but I made some mistakes along the way
also, when you say fish around the usb port. you mean inside the phone? Is there any danger of hitting the wrong pins and possibly hurting my phone? (say i hit pins 3 and 5 by mistake or something) or is it all pretty safe? I was going to try and attempt the jig method that only used the resistors but n oticed the pins were horrible small in the phone:/
Click to expand...
Click to collapse
It's not inside the phone... it's the USB port on the phone. One pin is on top and the other is on the bottom. If you don't have a JIG, that's the easy way to do it. There's no power on the USB port. This is a quick way to do it. You'll be fine. It's safe.
AdamOutler said:
It's not inside the phone... it's the USB port on the phone. One pin is on top and the other is on the bottom. If you don't have a JIG, that's the easy way to do it. There's no power on the USB port. This is a quick way to do it. You'll be fine. It's safe.
Click to expand...
Click to collapse
Sorry, that is what I meant. I meant to place where the charger is plugged in to. Just seems like the pins are really really tiny. Thank you for your help gonna get my resistors hopefully today and get my phone working again.
Hi,
I have done a lot of reading and searching, and I think I understand most of the basic pieces of what I am trying to do and how to do it. Let me explain.
Ultimately, I want to be able to install custom roms to my captivate.
Firmware: 2.2
Kernel: 2.6.32.9
Build: FROYO.UCKB1
I installed rom manager, but I see that with my hardware, I cannot install cwm recovery. It seems I need to downgrade my kernel using odin. Problem is, although I found the thread listing all of the kernels for download in zip format, I have no clue which one to use.
I found the instructions on how to reboot into cwm recovery, but without the new kernel, I cannot do it, at least that's what I gather.
Can you guys help me here? I know I am on the right track, but don't know what to do to go any farther. Also, I cannot get into recovery mode buy clicking the buttons. It seems I must now use adb. All I want to do at this point is reboot into cwm mode. Can that be so difficult.
Well, this is my first post. Thanks to all who reply.
Viper
3e recovery. Look in the stickies to fix that. OR flash another kernel (like Cog 4.x.x kernel) and flash a rom.
+1 to the above. Personally when flashing a custom ROM I just always start with JF6, the flash the green CWM update.zip file followed by the ROM, or if it's got an initial-kernel like many ROM's call for now days.
Quick stupid question...
Does the sim card need to be out to do this, or any of the other things I have been trying?
PghPittViper said:
Quick stupid question...
Does the sim card need to be out to do this, or any of the other things I have been trying?
Click to expand...
Click to collapse
It does not matter. The whole (remove SDCARD and SIM steps) in my opinion have always been false info. The only reason I'd remove anything would be the SDCARD if using a recovery that's untested to ensure it's not formatted or something like that.
error?
No matter what I try flashing with odin, I get this message:
<OSM> All threads completed. (succeed 0 / failed 1)
This indicates that the process failed. What gives?
Re-install your drivers. Then ensure the ODIN is open BEFORE connecting your phone in download mode. You can get the latest drivers in a package I made with ODIN here:
www.mediafire.com/?eyr42m5ilf03566
Edit: Also only use a genuine OEM cable when flashing. There are two many issues with non-oem cables and the usb data transfer they provide.
Need big time help now!!!!!!!!!!!!!! Possible Brick!!!
Now i have been playing with flashing roms. Now I have a real problem.
I flashed darky 10.2 i believe and now I am in a boot loop. It cycles between the white att screen and a colored pixelated screen.
I have been reading and researching for hours now. Present time 3:15 am. Research tells me that the cappy is pretty much un-brickable.
I KNOW I have to get into either download mode or recovery mode. I cannot do either.
I have researched this subject exhaustively, but my brain is fried now, and I work at 6:00 and need my phone.
What to do????
I emplore anybody up at this time to help.
TIA
PghPittViper said:
Now i have been playing with flashing roms. Now I have a real problem.
I flashed darky 10.2 i believe and now I am in a boot loop. It cycles between the white att screen and a colored pixelated screen.
I have been reading and researching for hours now. Present time 3:15 am. Research tells me that the cappy is pretty much un-brickable.
I KNOW I have to get into either download mode or recovery mode. I cannot do either.
I have researched this subject exhaustively, but my brain is fried now, and I work at 6:00 and need my phone.
What to do????
I emplore anybody up at this time to help.
TIA
Click to expand...
Click to collapse
What ROM were you coming from? Did you try all the 3 button combos? or battery pull/Vol+/- then plug in usb? Next best thing is a Homemade/bought Jig.
PghPittViper said:
What to do????
I emplore anybody up at this time to help.
TIA
Click to expand...
Click to collapse
Did you flash gingerbread bootloaders before flashing the ROM?
I am not amused by your phones performance
Did not flash gingerbread...
I apologize, my intent was not to amuse.
How now can I flash gingerbread if the phone wont stay powered on?
I ran home during my work break to check my replies.
Because I didn't flash gingerbread, I presume I was hasty in flashing darky becuause it seemed so great, is it possible to resurrect this phone?
I am feeling pretty discouraged.
Thanks and please continue to help.
As long as the phone shows any type of life its not Hardbricked and can be recovered with key combos or a Jig. Your fine. Get in to download mode and flash a clean stock and start over.
Entering recovery mode in my situation.
I am currently trying to hold the 2 button volume control and the power key.
The phone comes on to the att white screen, then goes black, then comes back on, etc...
I am very worried.
When I plug into the usb, it will connect to pc, then disconnect, then keep repeating this. I read that kies has an emergency recovery feature. But,, I can't connect to kies. Odin recognizes a port, but kies just says to connect your phone.
Any advice?
PghPittViper said:
I apologize, my intent was not to amuse.
How now can I flash gingerbread if the phone wont stay powered on?
I ran home during my work break to check my replies.
Because I didn't flash gingerbread, I presume I was hasty in flashing darky becuause it seemed so great, is it possible to resurrect this phone?
I am feeling pretty discouraged.
Thanks and please continue to help.
Click to expand...
Click to collapse
You don't need gingerbread BL for Darky 10.2. I've flashed Darky 10.2 before, his directions were pretty clear. I moved onto Fasty since his updates stopped. I suggest reading the stickies for making jigs or buying them as well. You can do it! & Good luck.
^what he said. You can try and taking out ur batter open odin, connect your phone hold Vol up and down insert battery. If that doesn't work you need a jig. Not hard to make, takes a little time though (if you peel a cheap cable for the plug that is)