Hello,
I have weird problem with my Samsung captivate.
I install a new rom on my device and it work well for several hours buy than it suddenly stop to work.
After a reset my device get stuck on the at&t screen.
I entered the download mode and flashed clean rom with odin (and check the Master Clear option).
But it still get stuck on the at&t screen.
Is this can be hardware problem?
Is there any way to get the log file from the boot to find out what is the problem?
Related
I have an i9000m which I had flashed to Froyo JPO with Odin, then installed Darky's ROM v 4.0. I had been using this for a while with no problem but a couple days ago it shut itself off for apparently no reason and when i tried to turn it on it would just get to the Galaxy S startup screen and then continuously restart and never fully boot. I could still get into download mode so I flashed back to the stock eclair JH2 firmware, but when I tried to turn the phone on, it would go through the normal boot sequence, but then i would be stuck at a black screen, with the bottom two buttons lighting up. I played around with flashing various different firmware versions, but it didnt help. After searching the forums it looks like it might be a problem with the internal SD card, but I'd like some other opinions/advice. Could anybody help me get my phone functioning again?
I'm having the exact same problem since today. It started out of nowhere; one moment the phone is working fine, the next its rebooting and it gets stuck...
Anyone got a solution besides a factory reset?
Hi guys, I have researched for quite a while not and I have found nothing that suits my situation.
I have flashed with multiple roms to no avail using ODIN. Everything appears to work fine, the rom uploads to the phone correctly, the phone reboots and comes to the Galaxy S logo and quickly resets and keeps on cycling.
Im not sure what I can do.
Any help appreciated, thanks.
try to flash a firmware that contains 3 files + pit.
if you cannot find one, try darkys new 9.2 resurrection. its only 1.tar file but you can use pit and re partition.... and it contains dbdata which should fix your problem
stuck on either the battery logo or the at&t screen
Hi I was trying to install Andremada3 on my galaxy captivate and got as far as installing URSA minor and then when I tried to install the Andremeda it was not on my sd card... so I tried to reflash to factory so I have access to the internal card to upload the zip file in doing so something happened and now my phone just keeps on flashing the battery icon or the at&t world phone screen and does not get past that... it does not even go into recovery mode by holding the volume and the power button... What can I do...Please help Thanks..
Hey,
I had the cm9 on my I9001, now i want to have the stock rom, i downloaded the Stock rom, ArriesVE.ops, and Odin.
Than i flashed the ROM on my phone, after this was done, it restarts, i can see the White Samsung Logo , after this i see the "Samsung Galaxy S Plus" Logo, this logo stays for a few seconds and than my phone restarts again and all repeats..
What should I do
Maybe this would help you http://broodplank.net/old/flashsamsungi9001.php
Same Thing...
Gnampf7 .. did u find a way past that.... have been stuck @ de same point whole day now... flashed the stock ROM thrice... cleared cache... cant do a factory reset thou... its asking for a passcode i dont have.
any ideas??
Bootloop on i9001
Hi guys, i gonna tell you about how my i9001 was stuck in a bootloop. Maybe you could help me. I'm sick of it.
Cause: I installed cm10 and cwm5 or 6 as recovery and upgrade my device by using Ota Updater. When I restarted my i9001, it got stuck in a bootloop.
What my i9001 can display: It can access to rampdump mode and download mode. In case I try to turn on my i9001 or access to recovery mode the Samsung logo is shown twice. It often gets stuck showing the typical grey battery flat (with a loading stopped) and the black screen alternately.
Attempts: i've tried everything except for the right solution. Lots of forum threads and nothing works for me. I've tried:
1.- Boot_loader for device boot.
2.- I've flashed an stock rom: XXKQP, and 2 more: BVKPC y XXKQ1. Each one are official.
3.- And then recovery-clockwork-5.5.0.4 and -6.0.1.2.
4.- I've tried, then, flashing feamodrecovery 1.2.
5.- Nothing works for me.
I've been using Odin 4.43. AriesVE in OPS section and when flashing these roms: one package. For recovery packeges: one package and pda (I tried these two options).
I can't reach at recovery mode. Any help would be greatly appreciated. Greetings!
http://forum.xda-developers.com/showpost.php?p=51290392&postcount=13
Hey everyone,
I have a problem. I want to turn in my phone at t-mobile and I've cleared my phone did a factory reset and unrooted the phone, everything is perfect. Except one thing, When you turn on the phone before the samsung logo I still have a custom deadmau5 picture and no matter what I do it shows up before the samsung logo. How can I fix this problem?
evocalante said:
Hey everyone,
I have a problem. I want to turn in my phone at t-mobile and I've cleared my phone did a factory reset and unrooted the phone, everything is perfect. Except one thing, When you turn on the phone before the samsung logo I still have a custom deadmau5 picture and no matter what I do it shows up before the samsung logo. How can I fix this problem?
Click to expand...
Click to collapse
Download the firmware from here > http://www.sammobile.com/firmwares/database/SM-G920T/
Extract the zip file and then flash the file using Odin.
If that doesn't fix it you might have to flash TWRP and do a full wipe and then flash the firmware.
I hope someone can help me.
I have an old galaxy note GT-N7000 which I still use and it’s rooted. Recently it has been giving me issues so I decided to do a factory reset which I thought would just fix everything. However, it just got stuck on the Samsung Galaxy note screen. It also only boots into download mode, not recovery mode & I have tried all the tricks and still it will not boot to the home screen.
I have downloaded a stock N7000 stock rom to flash back to stock, the Jodin program, including the pit file, but as soon as it connects and tells me to press start, all it says is running but does nothing. It will not allow me to flash anything.
Any idea why it’s stuck on the boot screen and how can I fix this? Should I have wiped something before doing a factory reset, as I don’t have a clue. Also if it’s best that I put a latest rom on it, I’ll be cool with it, as long as I can get it working again
Cheers for any help guys...
Thanks
Sent from my iPhone using Tapatalk