Related
I just got my "new" nook and tried to boot Froyo 0.6.8 from an SD card. It just gets stuck at the blue ANDROID_ screen. I tried Froyo 0.6.7 and redoing 0.6.8 but it never got past ANDROID_. I'm using a new Transcend 4GB class 6 card. I first tried writing it using WinImage and my laptop's built in card reader, but when that card didn't boot I tried using a USB card reader and Win32diskimager. The Nook came with 1.1 on it and I haven't done anything to the internal rom.
Any ideas? How long should it stay on the Android_ screen if its working?
Did you figure this out?
This sounds like the classic failure described with 16GB cards on multiple threads. There's a nice consolidated thread on cards that are known to work. I'd check that. I have froyo working beuatifully on an 8Gb class6 transcend card.
Most likely you have some glitch on the card. I would do a complete deep wipe of the card (e.g. using SDformatter, all options). Then reflash with win32diskimager, then expand the SDcard partition with EASUS
it should boot in a couple of minutes tops the first time round.
I looked at those threads about cards before I bought one and the Transcend 4gb, class 6 I got is one that seemed to work.
I haven't been able to get the nook to boot off any card. I tried doing the format suggested and tried another 1gb PNY card with the bootable clockwork. I've tried writing with the internal SD writer in my laptop and with a Kodak (sakar) usb writer and with Win32DiskImager and WinImage.
I suppose the USB writer I have might not be good, but I don't want to get another one without knowing its one that works. So far I don't know whether the problem is with the cards I'm writing or for some reason this nook won't boot off SD card.
Thanks for the suggestions.
I probably had a flaky 4gb card. Now it won't format or write whatever I do.
dumb Q, but is the 1gb card you ahve also flaky now too... in which case it might well be the reader?
Will your nook stock OS read the SD card? (e.g. throw some photos ont here and see if the nook will show them) that way eliminate the nook.
There's some older threads that suggest first formatting the SD card with the nook stock OS, but I've never needed to do that.
I'd persevere - there's definately some plusses of froyo over the rooted B&N (especially if you use adhoc networks a lot), and you absolutely need nookie froyo as a backup incase you fry something when you take the plunge to CM7 (which is phenomenal, despite being so early in its release)
The 1gb I borrowed seems ok. I managed to boot a card with a bootable clockwork on it. I didn't do anything to Nook stock OS yet. I want to be clear that I can recover if I do first. I did get another reader, but I think it was probably the card. I wasn't able to boot of the 1gb at first because I was making a mistake in unzipping the .tar.gz files.
Do you have any pointers of where to find out about how to use Clockwork recovery?
I am using 0.6.7 on a 8gb class 6 Transcend... it's working great, no issues with booting.
Hi,
I am unable to post in the dev forums. hence opening this thread.
I am facing a problem installing sd card bootable CM7.
I am refering to the folowing thread: [ROM][CM7] Size-agnostic SD Card image and CM7 installer for SD Cards. with updater: http://forum.xda-developers.com/showthread.php?t=1000957
I do the following:
1. Burn the 9M image (that would unpack into ~130M disk image)
2. Put the downloaded CM nightly build on the sdcard
3. Put the card in the nook color and boot
4. The nook boots to the installation process...penguin image in a corner and starts the process
However, it gets stuck at "Writing superblocks and filesystem accouting information".
I dunno if its stuck or not......because the cursor keeps on blinking.
Its been about 30 minutes and the screen stays in the above status only.
For information, I am using 16gb Kingmax Class 10 microsd card.
Any help will be greatly appreciated.......
acme2ajax said:
Hi,
I am unable to post in the dev forums. hence opening this thread.
I am facing a problem installing sd card bootable CM7.
I am refering to the folowing thread: [ROM][CM7] Size-agnostic SD Card image and CM7 installer for SD Cards. with updater: http://forum.xda-developers.com/showthread.php?t=1000957
I do the following:
1. Burn the 9M image (that would unpack into ~130M disk image)
2. Put the downloaded CM nightly build on the sdcard
3. Put the card in the nook color and boot
4. The nook boots to the installation process...penguin image in a corner and starts the process
However, it gets stuck at "Writing superblocks and filesystem accouting information".
I dunno if its stuck or not......because the cursor keeps on blinking.
Its been about 30 minutes and the screen stays in the above status only.
For information, I am using 16gb Kingmax Class 10 microsd card.
Any help will be greatly appreciated.......
Click to expand...
Click to collapse
Ummm... did you unpack the image prior to burning it to your Sdcard?
In addition it is not proven yet to work on 16gig cards, it has only been tested up to 8gig cards.
Edit: Others now have posted that 16gig cards do not work.
And Class 10 cards are known to have issue with Nook.
Search TITLES in this Forum only for "card" for threads on sd cards.
ADude said:
And Class 10 cards are known to have issue with Nook.
Search TITLES in this Forum only for "card" for threads on sd cards.
Click to expand...
Click to collapse
Hi Adude...Thanks for the update.
Have a small doubt...
I am able to install and run successfully, the sdcard bootable CM7 bt image...which is for 2gb card.
I, then, expand that partition to the rest of the card.
So is it the size of the card thats the issue?
Can this 'size agnostic' image be modified to write only to 2 or 4 gb and then we can expand the rest. I will like to ask this question to verygreen, but i still have some posts to go till I can paste in dev forums.
Thanks again for the info.......
Bumping an old thread, since I have the exact same problem, and can't post in the proper thread as well.
But I used a 2GB class 2 card( I think, it's a generic card that you get in the bundle when you buy a phone) instead, but got the same message.
Did I harm the card in anyway? Can I use it again for this procedure? Or do I have to reflash it in some way?
BrotherZero said:
Bumping an old thread, since I have the exact same problem, and can't post in the proper thread as well.
But I used a 2GB class 2 card( I think, it's a generic card that you get in the bundle when you buy a phone) instead, but got the same message.
Did I harm the card in anyway? Can I use it again for this procedure? Or do I have to reflash it in some way?
Click to expand...
Click to collapse
Generic Class 2 card. You answered your own question, it's probably too slow.
Pity, that's the only card I have lying around.
I'm very new to this so sorry for some very basic questions. But:
1. How do I restore the card to it's original state? I tried the HPUSBFW.EXE file that is in the link above(how to flash a bootable SD guide) but it says that I need admin rights even though I already am admin. Is there any other way to restore the card?
2. I have another generic 2GB from a Sony X10 mini pro, but no idea to try that then? What kind of SD-card should I buy? Since I saw that too fast SD cards have problem as well.
I also can't post in the dev thread and am having issues with this. I'm using an 8gb sandisk class 4 microsd card. I used win32imager to burn the agnostic iso file to the card. Then I clicked exit, unmounted the drive, and plugged it back in. Now the drive shows as a 115mb drive with 107mb free. In gparted it shows as 2 partitions, 1 as 115mb and another as unallocated with the rest of the 8gb. Windows can't see the unallocated one though.
So right now I'm stuck and can't copy the nightly cm7 build onto the drive. Anyone know why it formatted it like this and what I can do to fix it?
Here's an image of what I'm talking about:
107 MB is enough
gmanpie said:
I also can't post in the dev thread and am having issues with this. I'm using an 8gb sandisk class 4 microsd card. I used win32imager to burn the agnostic iso file to the card. Then I clicked exit, unmounted the drive, and plugged it back in. Now the drive shows as a 115mb drive with 107mb free. In gparted it shows as 2 partitions, 1 as 115mb and another as unallocated with the rest of the 8gb. Windows can't see the unallocated one though.
So right now I'm stuck and can't copy the nightly cm7 build onto the drive. Anyone know why it formatted it like this and what I can do to fix it?
Here's an image of what I'm talking about:
Click to expand...
Click to collapse
The nightly CM7 -87 file has around 91 MB (here: http://download.cyanogenmod.com/get/cm_encore_full-87.zip), so you should have enough space to copy it onto your sd card. Actually, that leaves more than 15 MB available, so I suggest you also put the gapps in your SD card (here: http://android.d3xt3r01.tk/cyanogen/gapps/gapps-gb-20110307-signed.zip)
About the unallocated space, it will be partitioned by the installer accordingly once you boot the NC with your SD card in it.
Looks like it's working now. I fit the nightly build on there but couldn't fit gapps(144mb). I messed up my froyo install earlier trying to put cm7 on, so I was worried I'd be stuck with a half functional rom for my upcoming 14 hr flight :/
Ok, now for my next question. How do I install it to the emmc? I tried installing it through froyo, but when I deleted the system folder and reset it to factory settings it messed up the froyo install, so now the rom manager doesn't work.
[Edit:] going to try following this thread:
http://fineoils.blogspot.com/2011/04/nookcolor-with-cyanogen-mod-70-emmc.html
What? Gapps is ~5MB only. If you're trying to install with both at the same time verygreen's instructions say that you should flash CM7 and turn on wifi first, prior to flashing gapps.
To install to EMMC you need to burn a CWM SD card, plop the nightly zip on there, boot up with it, then install zip from SD card (select the nightly). Wipe caches/data. Remove CWM card, hit reboot option in CWM menu. You'll need to either have a fresh SD card or reformat the CWM card since CM7 on EMMC requires an SD card in. Instructions for doing this (step by step) are somewhere in General forum by eyeballer.
(Also of note: the info that 16GB cards do not work with this image is no longer true)
Could anybody use a 16Gb sd card so far? I bought one just for the nook and now I found out that its not working - damn! I can't give it back so what? pls help!
Earymgn said:
Could anybody use a 16Gb sd card so far? I bought one just for the nook and now I found out that its not working - damn! I can't give it back so what? pls help!
Click to expand...
Click to collapse
I used SanDisk 16Gb and everything worked like a charm.
stud_muffler said:
I used SanDisk 16Gb and everything worked like a charm.
Click to expand...
Click to collapse
I did too(both with issues and successfully), the only problem I had with my card is that with the size of cm7 and gapps you ahve to flash them separately, so do cm7 first, put the gapps on the boot partition then reboot into recovery.
if you don't do that you'll run out of space on the boot partition during installation.
I used verygreen's instructions to put CM& on a Sandisk 16 gig class 4. Worked the first time I tried. After CM7 I shut down, put gapps on, then rebooted into recovery.
I think the majority of the problems people are having is NOT READING the part in the verygreen instructions about using Sandisk cards.
Imbroglio said:
I used verygreen's instructions to put CM& on a Sandisk 16 gig class 4. Worked the first time I tried. After CM7 I shut down, put gapps on, then rebooted into recovery.
I think the majority of the problems people are having is NOT READING the part in the verygreen instructions about using Sandisk cards.
Click to expand...
Click to collapse
Sandisk is not required.. I've also used Transcend and Kingston. Class 4 and 6 between the three.
What is required is a card that's not crap, or works like crap in the Nook Color. An OS does a lot of small operations or uses a lot of small files, so even if the card is great at mass transfers but sucks at smaller ones, it's going to be a bad experience.
Sandisk is one way to avoid it. So if you're buying one, might as well make it Sandisk. Any others.... if it doesn't work right, try a different card. That easy.
I have a new 1.2.0 nook color that is preventing me from booting from sd. Tried multiple manual nooter images. The symptom I face is the system does not boot atall, no display, nothing when I have the microsd that is a boot image in the slot. If I take out the microsd, after a few attempts it powers on. With the sd in place, it just does not power up. Tried pressing power, connecting to pc, connecting to power from the wall, all behave the same. It looks like Barnes and Noble went out of their way to block using nook to its full potential . Anyone work around this issue? I have read some of the other posts already, but it seems this problem is happening with only the most recent versions out there.
I can use the same micro sd fine with regular files. if there is a bootable image it stops booting. It looks like the firmware is checking the sd and if there is a boot image there, just suspending the device. Any help will be appreciated. I want to keep the original os on the nook, but need the flexibility of having another android install on a sd.
Maybe an obvious question, have you tried the latest clockworkmod recovery (3.0.2.8) as a bootable image on your sd card? I would first try if you can boot into recovery from the sd card before adding manual nooter into the mix. Manual Nooter is *not* a bootable image.
If all of this is old news for you, ignore my post.
Good luck with your new Nook Color.
Tried multiple versions including 3.0.2.8.
On your recommendation, tried just a bootable disk. That did not work either. I just cannot turn it on. No display at all.. I can only boot it up again if I remove the micro sd card. I tried the 8 gb image first then trying 1 gb image file nookdev-clockwork-0.7 on an 8 gb card then copying the uImage and uRamdisk files. Any problems with this approach? I am fairly new to nook/android, but tech savvy..
Have you tried different models/sizes of uSD cards? How about trying different software, card readers, or PCs to write the IMGs to the cards? At the bare minimum those should be attempted before blaming the Nook.
here is why I thought it may be a nook issue. I may be wrong, but here is the logic. I created the boot disk with win32diskimager-RELEASE-0.3-r27-binary. I can put the same card into the nook when it is already booted and can read these files. When i do this, the nook is creating the standard folders in addition to these files. So I am assuming that the card, writing software, etc may not be the issue since the nook is able to read. Is this assumption wrong? I don't have other size cards handy. I will order some and try in a few days. Meanwhile, if anyone else is facing this issue, please weigh in. Experts, please suggest if I can try something else.
nandsaa said:
On your recommendation, tried just a bootable disk. That did not work either. I just cannot turn it on. No display at all.. I can only boot it up again if I remove the micro sd card. I tried the 8 gb image first then trying 1 gb image file nookdev-clockwork-0.7 on an 8 gb card then copying the uImage and uRamdisk files. Any problems with this approach? I am fairly new to nook/android, but tech savvy..
Click to expand...
Click to collapse
There is an image for a bootable SD with CWM and the correct uImage and uRamdisk files (thanks to DizzyDen). That may be your problem. The SC card you created while it has the correct file structure may not have the correct boot information.
Yeah it's been my experience that the NC is more particular about what it will boot off of vs. what it will read from in normal use. Plenty of posts about this but in general you'll find most Sandisks just work so if you pick one up or borrow a card, try to get a Sandisk just to be on the safe side. Since no one else seems to be having the problem, I suspect it's probably just a card the NC doesn't like or a mostly good card with a bad sector in the wrong place.
Thanks a lot! I used the 2gb image and was able to do it with a 2gb card and 2gb_clockwork-3.0.2.8.rar file.
Have been able to root and unlock as well as install CWM v6.0.3.6. Currently running CM10.2, but my question is probably applicable to all of the ROMs.
I have a 16GB micro SD card that I've used in several phones, including my most recent Motorola Photon. I'm curious what everyone would recommend as to formatting the card and "starting fresh" if I wanted to dedicate the whole SD card to the phone (i.e., I will never remove it). What I mean specifically is that I want to dedicate the card to "add" to the 8GB that's already on the phone.
I guess what I'm asking is whether there is a way for the card to be formatted so that the Atrix thinks it's additional memory without realizing that it is an "external" SD card.
I would prefer to completely format the card as it's been used in other phones, and I want to re-install CM10.2 or maybe try ProBAM. I'm guessing generally the steps are:
1. format card based on what advice I get here
2. flash new ROM to phone
Update:
1. My phone memory was "full" even though I had very few apps. Turned out there were a bunch of "bp-dumps" being created--I presume they are like memory dumps when there is an error. I reflashed with Probam and so far things are okay.
2. I found this article that explains why one may to dedicate some card memory to SD-ext and a step-by-step of how to format. I note that I had to reboot once in between for the option of partitioning the SD-ext to show up:
http://forums.androidcentral.com/general-help-how/193297-everything-sd-cards-discussion-how.html
But it doesn't seem that Probam shows any change to the memory. I may have to reflash it a couple of times, as one of the posts suggested.
If anyone has anything to chime in with, I'd be grateful.
Hello,
I'm currently running my Nook HD+ on Jellybean, using one of verygreen's boots.
(NookHDplus-verygreen-New-SD-add-bokbokan-Cyanoboot-rev0-(06.01.13) to be exact)
I'm wanting to upgrade to KitKat, because a few reviews say it provides a better experience.
So I followed the instructions here:
http://forum.xda-developers.com/showthread.php?t=2602796
It's all very familiar, and is pretty much the same exact process as I followed when I successfully did the verygreen boot above.
I've got everything loaded onto my 8GB SanDisk SD Card, it's in my Nook HD+, and I'm ready to go.
At least, that's what I thought.
I seem to be having this issue where it's not able to find my SD Card.
When I load cyanoboot universal bootloader, CWM only gives me the options to install zips from /sdcard.
Correct me if I'm wrong, but /sdcard is classified as the internal "sd card"; and the thing I'm wanting is ext_sdcard, right?
So the question is, how do I point my device in the direction of the external SD Card, so it can boot from it?
Not sure if this helps, but when I spring my SD Card out and back in, it returns the following:
/storage/ext_sdcard: Idle-Unmounted
/storage/ext_sdcard: Checking
/storage/ext_sdcard: Idle-Unmounted
I could be wrong; as I'm no programmer, or by any means a developer, but this sounds like it's recognizing the drive, but unmounting it immediately after recognition.
Thanks in advance,
Vahn
I'm definitely no expert, but looking at the link you provided, step 6 says to copy the files to the INTERNAL SD (internal memory) as the current CWM can only read the internal SD. So it seems you boot from the external SD card, but you need the files on the internal memory for it to find them?
Update:
Fixed it myself.
I just had to completely re-format the SD Card, and drag/drop the ZIP files (CWM-Recovery-Ovation, CM-11, and PA_GAPPS).
Then I restarted the Nook WITHOUT THE SD CARD, and it started recognizing external_sd.
I put the SD Card in, mounted it, loaded the zips from external, and it worked like a charm.
Since your HD+ already had CM10.x on EMMC, there is a simpler process that does not require use of an external SD card: http://forum.xda-developers.com/nook-hd/general/how-to-updating-hd-hd-internal-emmc-to-t2863171.